DSE 7560 Installation Instructions Manual

DEEP SEA ELECTRONICS

7560 INST AL LA T IO N IN ST R UC TI ON S

053-054

ISSUE 4

ACCESSING THE FRONT PANEL CONFIGURATION EDITOR

.

• Press the Stop/Reset and Info buttons simultaneously.

• If a module security PIN has been set, the PIN number request is then

shown :

• Press

(up) or

(down) to adjust it to the correct value.

• Press (right) when the first digit is correctly entered. The digit you have just entered will now
show ‘#’ for security.

•

Repeat this process for the other digits of the PIN number. You can press

(left) if you need to

move back to adjust one of the previous digits.

•

When is pressed after editing the final PIN digit, the PIN is checked for validity. If the number is
not correct, you must re-enter the PIN.

•

If the PIN has been successfully entered (or the module PIN has not been
enabled), the editor is displayed :

EDITING A PARAMETER

• Enter the editor as described above.

• Press the left or right buttons to cycle to the section you wish to view/change.

• To edit the parameter, press to enter edit mode. The parameter begins to flash to indicate that

you are editing the value.

• Press the up or down buttons to change the parameter to the required value.

• Press to save the value. The parameter ceases flashing to indicate that it has been saved.

• To exit the editor at any time, press the button.

Deep Sea Electronics Plc.

Tel:[phone]

Fax: [phone]

LO CALL (from UK BT landlines) :

Telephone [phone]

Email: [e-mail]

Web:

www.deepseaplc.com

Deep Sea Electronics inc.

Phone: [phone]

Fax: [phone]

TOLL FREE (USA only) : Tel: [phone]

Email: [e-mail]

Web: www.deepseausa.com

Deep Sea Electronics Plc.

(Far East)

Tel:[phone]

Fax: [phone]

Email: [e-mail]

Web: www.deepseaplc.com

NOTE: When the editor is visible, it is automatically exited after 5 minutes of inactivity to
ensure security.
NOTE: The PIN number is automatically reset when the editor is exited (manually or
automatically) to ensure security.
NOTE: More comprehensive module configuration is possible using the 75xx series PC
configuration software. Please contact us for further details
NOTE: The contents of the tables overleaf may differ depending on the actual module
configuration.

TYPICAL WIRING DIAGRAM

ADJUSTABLE PARAMETERS.

Front Panel Configuration Editor

(Factory default settings are shown in bold italicised text)

Section

Parameter

as shown on

Values

Timers

Mains Transient Delay

0 -10s (2s)

Start Delay

0– 60m (5s)

Transfer Delay

0– 10s (0.7s)

Return Delay

0– 60m (30sa0

Low battery Delay

0– 10m (1m)

High battery Delay

0– 10m (1m)`

Mains

Mains Under Voltage Alarm 50V-360V ph-N (184V)

(184V)(184V)

(184V)

Mains Over Voltage Alarm 50V-360V ph-N (276V)

(276V)(276V)

(276V)

Mains Under Frequency 0Hz-75Hz (45Hz)

(45Hz)(45Hz)

(45Hz)

Mains Over Frequency 0Hz-75Hz (55Hz)

(55Hz)(55Hz)

(55Hz)

System

Plant Battery Under Volt Alarm 0-40V (10V)

(10V)(10V)

(10V)

Plant Battery Over Alarm 0-40V (30V)

(30V)(30V)

(30V)

Misc

Language English, Other

Alternative Frequency Enable Disable

DisableDisable

Disable

Alternative Voltage Enable Disable

DisableDisable

Disable

AC System

3 phase 4 wire

3 phase 4 wire3 phase 4 wire

3 phase 4 wire

Single phase 2 Wire
3 phase 3 wire
2 phase 3 wire L1 & L2
3 phase 4 wire ED
2 phase 3 wire L1 & L3

Contrast

 l 

Date and Time dd mmm yyyy hh:mm

Auto Scroll Time 0-10s (2s)

(2s)(2s)

(2s)

Mains CT Primary Rating 5A- 6000A (600A)

(600A)(600A)

(600A)

Mains CT Secondary Rating 1A, 5A (5A)

(5A)(5A)

(5A)

Load Ramp Rate

0.1%-100% (

2.0%)

2.0%)2.0%)

2.0%)

(% per sec)

ACCESSING THE ‘RUNNING’ CONFIGURATION EDITOR

• The ‘running’ editor can be entered while the engine is running. All protections remain active if the
engine is running while the running editor is entered.

• Press and hold the button to enter the running editor.

EDITING A PARAMETER

• Enter the editor as described above.

• Press the left or right buttons to cycle to the section you wish to view/change.

• Press the up

or down

buttons to change the parameter to the required value.

• To save paremeters scroll to `save changes and exit followed by the down buttton

• To cancel changes scroll to `Abandon changes and exit followed by the down

button

ADJUSTABLE PARAMETERS (Running editor)

Running Editor

Section Parameter as shown on display

Factory Settings

DISPLAY Contrast

 l 

Language

English

Load power factor

%

Load parallel power

%

Enable commissioning screens

No

Voltage adjust

(manual mode only engine running bus breaker open )

Raise Steady Lower

Frequency adjust

(manual mode only engine running bus breaker open )

Raise Steady Lower

Enable mains decoupling

No

Abandon changes and exit

Save changes and exit

DIMENSIONS

240.0mm x 181.1mm x 41.7mm (9.4” x 7.1” x 1.6”)

PANEL CUTOUT

:

220mm x 160mm (8.7” x 6.3”)