How it Works
DS2
Loading...
#
D
Loading...
Loading...
72LT4
User Manual
31 pgs3.99 Mb0

DS2 72LT4, 72LT6 User Manual

Download
Page 1
User Manual
Professional LCDs
Page 2
DS72LT4, LT6 User Manual 1
Contents
Safety Precautions........................................................................................................................................................3
Important Safety Information ........................................................................................................................................4
Declaration of Conformity .............................................................................................................................................6
Getting Started..............................................................................................................................................................7
Installation.....................................................................................................................................................................9
Operating Instructions.................................................................................................................................................18
Navigating the On Screen Display (OSD) Menu ........................................................................................................22
Specifications..............................................................................................................................................................24
Input Mode..................................................................................................................................................................25
Pin Assignments.........................................................................................................................................................26
Page 3
DS72LT4, LT6 User Manual 2
Digital RGB Input (DVI-D): DVI......................
.
........................................................................................................26
Troubleshooting..........................................................................................................................................................28
Recycling and Energy Information..............................................................................................................................29
Material Contents Declaration ....................................................................................................................................30
Page 4
DS72LT4, LT6 User Manual 3
Safety Precautions
CAUTION
Do not install display in a wet environment or place anything on the top of the display filled with liquid, such as vase or beverage. Do not install near flammable objects, such as gasoline or other volatile liquids. Do not install near any heat sources such as radiators or other heating devices. Do not install in a dusty environment. Do not damage the power cord or plug. Do
not disassemble the screen to avoid electric shock.
WARNING
After extended use the heat sink behind the screen may be hot. Do not touch to avoid being burned. Do not touch the screen panel with sharp objects or extreme pressure to avoid damage to the panel. The display should be installed in well-ventilated place, do not install in a confined space. Do not drop or allow any object to fall on the screen. Do not touch the screen with wet hands to avoid electric shock. When cleaning, unplug the monitor. Use a soft, dry cloth to wipe the screen off. Do not use alcohol or other chemicals. If you smell smoke or hear a strange noise, immediately unplug the monitor and contact the vendor. Do not discard this product with general household waste. Please be sure to comply with the local waste regulations. Su
itable for mounting on concrete or other non-combustible surface only.
IMAGE BURN-IN WARNING
When a stationary or fixed image is displayed for a long time on the screen, the image may be permanently imprinted on the screen. This phenomenon is known as image burn-in and is not covered by the manufacturer's warranty. In order to avoid burn in, avoid prolonged display of static or fixed images on the screen.
Page 5
DS72LT4, LT6 User Manual 4
Important Safety Information
Disassembling the LCD is strictly prohibited. Opening the cover may expose the user to shock or other
hazards. Please contact DynaScan certified service professionals for all maintenance requirements.
Do not allow any liquid to enter the LCD. Also avoid placing the LCD close to a water sources.Do not place heavy objects on the power cord. A damaged power cord might cause electric shock or fire.Do not bend, curl, or damage the power cord.The power cord must comply with local safety regulations.Do not damage or modify the prongs/pins and the ground contact on the power plug.Do no place the LCD on an unleveled surface or an unstable vehicle. The LCD could fall over and cause
substantial damage.
Do not cover the vents and/or the heat sink.Do not install the LCD beside radiators or other heat sources. The installation site should have sufficient
ventilation so the heat generated by the LCD can be dissipated.
Do not use the Signage in a hot, humid, dusty, or fumy environment.Handle the LCD with care. Save the packaging materials for the next transport.Please clean the backside of the LCD at least once a month for dust and other particles.
Unplug the LCD immediately and contact a DynaScan certified service professional as soon as possible when any of the following situations occurs:
Damaged power cord or power plug.If liquid or foreign objects has entered the LCD.If the LCD has been exposed to rain or water.If the LCD has been dropped or the casing has become damaged.If you notice any structural damage such as cracks, or unnatural vibration.If the LCD cannot be operated following the steps outlined in this manual.If the LCD emits smoke or other odors, or generates strange noises.
Operating Suggestions
Avoid displaying a stationary image for a long period of time in order to prevent image sticking.
Page 6
DS72LT4, LT6 User Manual 5
Cleaning the Panel
Use a soft, lint-free cloth to gently wipe dust off the screen panel.
Do not use any hard material to wipe the panel. Do not poke the panel with your hand or any sharp object (such as a pen or a nail) or exert excessive pressure
to the panel to prevent damage to the panel.
Do not use any cleaning solution on the panel as it might cause discoloration.
Cleaning the Casing
Unplug the power cord. Gently wipe the casing with a soft cloth.
Attention
Do not use any of the following solutions to clean the casing as they might damage the paint and cause it to
crack or peel: benzene solution, alkaline solution, alcohol-based cleaning solution, glass cleaner, wax, polisher, or detergent.
Page 7
DS72LT4, LT6 User Manual 6
Declaration of Conformity
FCC Verification
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Information
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Declaration of the Manufacturer
We hereby certify that the Professional LCD DS72LT4, LT6 is in compliance with Low Voltage Directive 2006/95/EC Electromagnetic Compatibility Directive 2004 /108 /EC
IEC60950-1:2005+A1(2nd Edition) E
N60950-1:2006+A1:2010 EN55022:2006+A1:2007 Class A EN61000-3-2:2006+A1:2009+A2:2009 EN61000-3-3:2008 EN55024:1998+A1:2001+A2:2003 EN61000-4-2:2009 EN61000-4-3:2006+A1:2008+A2:2010 EN61000-4-4:2010 EN61000-4-5:2006 EN61000-4-6:2009 EN61000-4-8:2010 EN61000-4-11:2004 EN61000-4-11:2004
DynaScan Technology, Inc.
Page 8
DS72LT4, LT6 User Manual 7
Getting Started
Contents
Confirm the accessories below are included with the display. If any item is missing, please contact your dealer. The color and shape of the accessories may vary by product.
• DS72LTx Professional LCD
• Remote Control x1 pcs
• Batteries (1.5V / AAA) x2 pcs
• Quick Start Guide x1 pcs
• Power cable x1 pcs
• RS-232 cable x1 pcs
• DVI cable x1 pcs
• CD-ROM x1 pcs
• Ethernet crossover cable x1 pcs
Attention: Please use the following table to check whether the included power cord is suitable for your region. If the power cord does not match your region, please contact your local supplier. Please use matching AC socket in order to meet local safety regulations.
DS72LT4
Plug Type North America European Continental
Japanese Taiwanese
Plug Shape
Region U.S.A. / Canada
EU
(Except U.K.)
Japan Taiwan
Voltage 120V 230V 100V 110V
DS72LT6
Plug Type North America European Continental
Plug Shape
Region U.S.A. / Canada
EU
(Except U.K.)
Voltage 220V 230V
Page 9
DS72LT4, LT6 User Manual 8
Installing and Replacing Remote Control Batteries
1. O
pen the battery compartment cover.
2. Insert 2 new AAA batteries.
3. Close the battery compartment cover.
Warning:
• Incorrect usage of batteries may cause leakage or explosion.
• Pay attention to the polarity when installing batteries.
• Do not use batteries from different brands together. Do not mix new and used batteries. Doing so may
shorten the battery life or cause leakage.
• Remove the batteries or replace them with a new pair when the batteries are depleted in order to prevent battery leak in the battery compartment.
• Do not touch the leaked substance from the batteries in case of a battery leak. Doing so may damage human skin.
Note: if you plan on not using the remote control for a long period of time, we recommend removing the batteries from the remote control.
Page 10
DS72LT4, LT6 User Manual 9
Installation
The LCD must be properly installed using a wall mount. Incorrect installation may cause injury or damage the equipment. Product warranty does not cover damages caused by improper installation and DynaScan shall not be held responsible in such incident.
Mounting
Hanging the Professional LCD from the ceiling or mounting it on the wall is the responsibility of the user. Not all
ceilings or walls provide enough strength to support the LCD. The LCD may drop and cause serious injury if it is hanging from the ceiling with insufficient support or is mounted on a slanted wall. Product warranty does not cover improper installation, modification, or damages caused by natural disasters. DynaScan recommends hiring certified professionals to evaluate the installation site and mounting operation.
Do not to cover the vent and/or the heat sink in order to ensure proper heat dissipation. Refer to the installation guide provided by manufacturer of the mount for proper installation.
When mounting on a wall or hanging from a ceiling
A wall mount is not included in the accessory. Please purchase a VESA Standard wall mount to secure the
LCD. DynaScan is not responsible for damages caused by using non-standard wall mounts.
Verify that the mounting location can support the weight of the LCD before installation. The installation angle must be within 15 degrees of the vertical axis. Do not install the wall mount while the power is turned on as it may cause serious injury from electrical shock.
Model Number VESA (mm) Screw specification
Screw Length Number
(A * C) 400 * 400
DS72LT4 DS72LT6
(B * C) 800 * 400
M6
Greater than 10mm
(not including wall
mount thickness)
8
Page 11
DS72LT4, LT6 User Manual 10
DS72LT4 Unit:
DS72LT6
A B C
A B
C
[inch]
mm
Page 12
DS72LT4, LT6 User Manual 11
Orientation
W
hen used in the portrait orientation, the LCD should be rotated clockwise such that the left edge becomes the
top edge.
Installation Location
The ceiling or the wall must have enough strength to support the LCD and its accessories.Do not install in a location with strong vibrations or is dusty.Do not install near the building’s main electric panel.Do not install at a location where the LCD can be easily removed by the general public.When installed in an alcove, leave at least 10cm (4”) of space around the LCD to ensure proper ventilation.
10 cm / 4 in
10 cm / 4 in
Page 13
DS72LT4, LT6 User Manual 12
When hanging from a ceiling
Ensure that the ceiling is strong enough to support the LCD and it accessories. Also consider the effects of earthquakes, unexpected vibrations, and other external forces when evaluating the ceiling strength.
The LCD should be secured to the building’s structural frame, such as a beam, and not to materials such as light
steel frame or interior decoration.
Do not use wood screws or dry wall anchors for installation.
Maintenance
Inspect the fasteners regularly for signs of loosening or deformation. Please perform appropriate corrective
measures when a problem is identified. Neglecting the problem may worsen the situation.
Increase the inspection frequency on areas where previous maintenance had occurred to ensure the problems
do not occur again.
Page 14
DS72LT4, LT6 User Manual 13
Connecting To a Power Source
Using the power cable provided, insert the female connector into the back of the display as shown in the diagram b
elow. Connect DS72LT4 power cable to a 100-240 Volt, 50 / 60Hz AC power outlet. Connect DS72LT6 power cable to a 200-240 Volt, 50 / 60Hz AC power outlet. Insert the plug completely into the socket. A loose power connection may cause degradation to the image quality.
Connecting an External Video Source
Turn OFF the power to both the LCD and the external video device. Using the DVI cable provided, insert one end into the DVI-IN on the back of the display as shown in the diagram below. Connect the other end of the DVI cable to the DVI output of the video source. Refer to your video device’s product manual for additional information
DVI Cable
DVI (IN)
DVI (OUT)
Page 15
DS72LT4, LT6 User Manual 14
Connecting Multiple Displays for Video Wall Applications
To daisy chain multiple displays for a video wall application, connect a video source to the 1st display into the chain w
ith the supplied DVI cable and RS-232 cable. Connect the DVI-OUT of the 1st display to the DVI-IN of the 2nd display. Using the Ethernet crossover cable provided, connect the RS-485 OUT of the 1st display to the RS-485 IN of the 2nd display. Repeat connection for remaining displays. Use the OSD Menu or Display Manager software to configure the size of the video wall and the position of each display.
Note: The maximum number of DS72LTx’s in a Video Wall is 36 (6 × 6).
Note: The DynaScan “Display Manager” application is required to be installed on the PC in order to use the
External Control feature.
Note: The Daisy Chain Setting (video wall function) only supports a resolution of 1920 x 1080 (1080p).
DISPLAY 1
DISPLAY 2
DISPLAY 3
DVI (OUT)
DVI (IN)
DVI (IN)
RS-485 (OUT)
RS-485 (IN)
Video Source
RS-232 (IN)
DVI (OUT)
RS-232 (OUT)
DVI (OUT)
DVI (IN)
RS-485 (OUT)
RS-485 (IN)
Page 16
DS72LT4, LT6 User Manual 15
Connector Positions
RS-485 (IN) RS-232 (IN) DVI (IN) DVI (OUT) RS-485 (OUT) AC (OUT) AC (IN)
Unit:
DS72LT4
  
[inch]
mm
Page 17
DS72LT4, LT6 User Manual 16
DS72LT6
  
Page 18
DS72LT4, LT6 User Manual 17
Input / Output Terminals
○○○○
1 RS-485 (IN): RS485 control function for the daisy chain application.
○○○○
2 RS-232 (IN): RS232C network input connection for the use of remote control from computer.
○○○○
3 DVI (IN): Connect the DVI-D output of a PC, or the HDMI output of an AV device by using a DVI-HDMI cable.
○○○○
4 Audio (IN): Connect audio input from external AV device.
○○○○
5 Extension Connector: Extension Connector for optional IR Extension sensor kit (ESK201).
○○○○
6 DVI (OUT): Output the signal from the DVI IN.
○○○○
7 RS-485 (OUT): RS485 control function for the daisy chain application.
○○○○
8 Audio (OUT): Connect the audio signal output from Audio IN jack to an external AV device.
○○○○
9 Power Switch: Press to switch the main power on/off.
○○○○
10 AC (IN): Connect the supplied power cord to the wall outlet.
○○○○
11 AC (OUT): AC outlet 100~240V up to 100 Watt.
○
6
○
7
○
8
○
9
○
10
○
11
○
5
○
4
○
3
○
2
○
1
Page 19
DS72LT4, LT6 User Manual 18
Operating Instructions
Powering On/Off the Display
To turn on/off the display, press the power switch on the back of the display as shown in the diagram below.
Using the Remote Control
When using the remote control, aim the remote at the IR receiver on the display. The IR receiver on the DS72LTx model is at the back of the display with a receiving angle of 100 degrees. The IR receiver configurations of the two models are shown in the figure below.
The operating range of the remote control is 2.5 meters (8 feet).
Ambient light may affect the performance of the remote control. Avoid fluorescent or neon lights in the vicinity.
OFF
NOTE: the remote control only works when the main switch is in the ON position.
ON
Page 20
DS72LT4, LT6 User Manual 19
DS72LT4 DS72LT6
Front
Back
100°°°°
100°°°°
Page 21
DS72LT4, LT6 User Manual 20
Using the Remote Control (cont.)
Color and shape may vary by model.
ITEM DESCRIPTION
POWER Power On / Off
MENU OSD On / Off
UP Move the cursor up or change the setting of the selected item
LEFT Exit the current selection
RIGHT Select the highlighted item
DOWN Move the cursor down or change the setting of the selected item
Page 22
DS72LT4, LT6 User Manual 21
Using the Rear Panel Controls
ITEM DESCRIPTION
MENU OSD On / Off UP Move the cursor up or change the setting of the selected item DOWN Move the cursor down or change the setting of the selected item LEFT Exit the current selection RIGHT Select the highlighted item
Page 23
DS72LT4, LT6 User Manual 22
Navigating the On Screen Display (OSD) Menu
Press the MENU button on either the real panel control or remote control to display the OSD. Use the navigation arrows to select and adjust menu items.
ITEM DEFAULT DESCRIPTION
DISPLAY MODE LAN.
Change the orientation of the Menu. The Menu can be displayed in either LANDSCAPE or PORTRAIT mode.
AUTO BRIGHTNESS OFF
Turn On / Off auto brightness adjustment. Note: With AUTO BRIGHTNESS on, the display brightness adjusts according to the ambient light. When ambient light is bright, the screen will adjust to the set HIGH LEVEL brightness value; when ambient light is dark, the screen will adjust to the set LOW LEVEL brightness value. With AUTO BRIGHTNESS off, screen brightness will remain at HIGH
LEVEL set brightness value. HIGH LEVEL 99 Adjusts the highest brightness level. Range 0 – 99. LOW LEVEL 50 Adjusts the lowest brightness level. Range 0 – 99.
COLOR TEMPERATURE 6500K
Color temperature select (5500K 6500K 9300K and USER
MODE). R 99 Adjust the red light level. Range 0 – 99. G 99 Adjust the green light level. Range 0 – 99. B 99 Adjust the blue light level. Range 0 – 99.
CONTRAST 32 Adjust the contrast level. Range 0 – 99. SCREEN SAVER OFF Turn on / off image burn-in protection.
INTERVAL 5 min Sets image burn-in protection interval.
CURRENT TIME 00：00
Set the clock.
Note: The internal clock will continue to function when the
power is turned off.
TIMER OFF Turn on / off automatic power schedule function.
POWER ON TIME 00：00 Set turn-on time. POWER OFF TIME 00：00 Set turn-off time.
DAISY CHAIN SETTING Set video wall function.
NUMBER OF ROWS 1
Set number of rows in video wall.
Note: The maximum number of rows in a daisy chain is 6.
NUMBER OF COLUMNS 1
Set number of columns in video wall.
Note: The maximum number of columns in a daisy chain is 6. ROW POSITION 1 Vertical position in video wall.
Page 24
DS72LT4, LT6 User Manual 23
COLUMN POSITION 1 Horizontal position in video wall.
LOCAL DIMMING MODE 1 LOCAL DIMMING is on MODE 1. GAMMA NATIVE Adjusts the Gamma value.
IR CONTROL ON
Enables / disables the ability to use the remote to control the
Menu.
Note: When disabled, the remote control function can be
enabled again from the control panel on the Signage or
through the DynaScan “Display Manager” application.
POWER SAVE MODE
When in Power Save Mode, RS-232 controls do not function.
Only [Main Power Switch] on the display or [Power Button] on
the remote controller can wake up the display.
RESET TO FACTORY DEFAULT
OFF
Restores all settings to default.
Note: Does not modify CURRENT TIME, POWER ON TIME,
POWER OFF TIME.
SN: xxxxxxxxxxxxx The display’s serial number. VER: 0.0.01 1920x1080 The F/W version ; Input resolution.
Some functions may not be available for all models.
*Adjusted value: Each R/G/B value for this product has been individually adjusted in during production to a
preset color temperature of 6500K.
Page 25
DS72LT4, LT6 User Manual 24
Specifications
MODEL DS72LT4 / DS72LT6
LCD Panel Size 72.07 inches Native Resolution 1920 x 1080
DS72LT4 2500 cd/m² (Typ.)
Brightness
DS72LT6 5000 cd/m² (Typ.)
Contrast Ratio
3,000:1 (Static)
1,000,000:1 (Dynamic) Response Time 12 ms (Typ.) Viewing Angle
178° / 178° Life Time 50,000 hrs (Typ.)
PANEL
Panel Surface AR, 3H Power Supply Internal
DS72LT4 100 ~ 240V, 50 / 60Hz Rated Voltage
DS72LT6 200 ~ 240V, 50 / 60Hz
DS72LT4 Max. 920W Power On Mode
DS72LT6 Max. 2050W Standby Mode < 1W
POWER
AC Out < 100W Bezel Width (T/B/L/R) 30/30/30/30 mm Cabinet Color Black
DS72LT4 1666 x 968 x 135 mm Monitor Dimension (LxHxD, w/o Stand)
DS72LT6 1666 x 968 x 160 mm
DS72LT4 95 kg / 103 kg Monitor Weight (set / package)
DS72LT6 103 kg / 111 kg
MECHANICAL SPECS
VESA Mounting (Dimension) 8 Holes (400x400 mm, 800x400 mm)
USER INTERFACE OSD Language English
Operation Temperature
0°C ~ 40°C Storage Temperature
-20°C ~ 60°C
ENVIRONMENT
Humidity 10%~80% RH Non-Condensing DVI-D IN *1 / OUT *1 RS-232 IN *1 RS-485 (RJ-45) IN *1 / OUT *1
I/O Ports
Audio IN *1 / OUT *1
Design and specifications are subject to change without notice. DVI-D out only supported resolution is 1920 x 1080 (1080p).
Page 26
DS72LT4, LT6 User Manual 25
Input Mode
Active Resolution
H Pixels V Lines
Refresh Rate Pixel Rate Aspect Ratio
640 480 60 Hz 25.175 MHz 4:3 720 480 50 Hz 27 MHz 4:3 720 480 59.94 Hz 27 MHz 4:3 800 600 60 Hz 40 MHz 4:3
1024 768 60 Hz 65 MHz 4:3
50 Hz
1280 720
60 Hz
74.25 MHz 16:9
1280 768 60 Hz 79.5 MHz 5:3 1360 768 60 Hz 85.5 MHz 16:9 1920 1080 60 Hz 148.5 MHz 16:9
50 Hz
1920 1080
60 Hz
148.5 MHz 16:9
Page 27
DS72LT4, LT6 User Manual 26
Pin Assignments
Digital RGB Output (DVI-D): DVI
PIN ASSIGNMENT OF DVI CONNECTOR
01 TX2- 09 TX1- 17 TX0­02 TX2+ 10 TX1+ 18 TX0+ 03 Shield (TX2 / TX4) 11 Shield (TX1 / TX3) 19 Shield (TX0 / TX5) 04 NC 12 NC 20 NC 05 NC 13 NC 21 NC 06 DDC-Serial Clock 14 +5V power 22 Shield (TXC) 07 DDC-Serial Data 15 Ground 23 TXC+ 08 NC 16 Hot plug detect 24 TXC-
Digital RGB Input (DVI-D): DVI
PIN ASSIGNMENT OF DVI CONNECTOR
01 RX2- 09 RX1- 17 RX0­02 RX2+ 10 RX1+ 18 RX0+ 03 Shield (RX2 / RX4) 11 Shield (RX1 / RX3) 19 Shield (RX0 / RX5) 04 NC 12 NC 20 NC 05 NC 13 NC 21 NC 06 DDC-Serial Clock 14 +5V power 22 Shield (RXC) 07 DDC-Serial Data 15 Ground 23 RXC+ 08 NC 16 Hot plug detect 24 RXC-
Page 28
DS72LT4, LT6 User Manual 27
RS-232 Output
PIN No. NAME
01 connected to 7&8 02 RXD 03 TXD 04 connected to 6 05 GND 06 connected to 4 07 connected to 1&8 08 connected to 1&7 09 NC
RS-232 Input
PIN No. NAME
01 connected to 7&8 02 TXD 03 RXD 04 connected to 6 05 GND 06 connected to 4 07 connected to 1&8 08 connected to 1&7 09 NC
Page 29
DS72LT4, LT6 User Manual 28
Troubleshooting
ISSUE RECOMMENDED SOLUTION
No image is displayed.
• Check whether the DVI in cable is completely plugged in.
• Check whether the main switch is in the ON position, and the power cord
is completely plugged in.
• Check whether the image source’s resolution is set to 1920 × 1080 (1080p).
• Check whether the DVI cable is damaged or bent excessively.
Nothing happens when switching the main switch on.
• Unplug the power cord from the socket and plug it back in after a few seconds to reset the display.
Note: DS65LT4 does not have a power off indicator. Note: Unplugging the power cord will not change the settings.
Image is unstable.
• Check whether the DVI in cable is completely plugged in.
The remote control does not work.
• Check whether there are batteries in the remote control.
• Check the batteries for freshness, polarity, etc.
• Check whether the remote is in the operation range.
• Bright light may interfere with the remote control. Please avoid using
the remote control near special fluorescent lights or neon lights.
Auto on/off does not work or does not function properly.
• Check whether the TIMER setting in the menu is set to “OFF”.
• Check whether the “Power On Time” and “Power Off Time” settings are
set correctly.
Cannot control the display remotely via RS-232.
• Check whether the RS-232 cable is connected properly.
• Check whether the Ethernet crossover cable is connected properly.
If you are still having trouble with your DynaScan DS² Professional LCD, contact your dealer or DynaScan directly for more assistance.
Page 30
DS72LT4, LT6 User Manual 29
Recycling and Energy Information
DynaScan is firmly committed to its environmental protection efforts and we believe that reducing our products’ impact on the environment is of the utmost importance. We are dedicated to meet the latest environmental protection regulations.
Energy usage
Mode Energy consumption
DS72LT4 Max. 920 W
Normal
DS72LT6 Max. 2050 W
Standby < 1 W
Disposal
Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact your local government for information regarding the collection systems available. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being. When replacing old appliances with new one, the retailer is legally obligated to take back your old appliances for disposal at least for free of charge.
Page 31
DS72LT4, LT6 User Manual 30
Material Contents Declaration
Hazardous Substances
Lead Mercury Cadmium
Hexavalent
Chromium
Polybrominated
Biphenyls
Polybromodiphenyl
Ethers
Part Name
Pb Hg Cd Cr6+ P
BB PBDE
PCBA
O O O O O O
CHASSIS
O O O O O O
ACCESSORY
O O O O O O
PACKAGE
O O O O O O
“O” indicates that the level of the specified chemical substance is less than the threshold level specified in the standards of SJ/T-11363-2006 and EU 2005/618/EC. “” indicates that the level of the specified chemical substance exceeds the threshold level specified in the standards of SJ/T-11363-2006 and EU 2005/618/EC.
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use