Dräger Alcotest 6810 GB Operator's Instruction Manual

Alcotest® 6810 GB
Breath Alcohol Screening Device with Datamanagement
D
Alcotest 6810
ST-207-2004_sw_6810.eps
Contents
For your safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
What‘s what? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Measuring instrument . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Inserting the batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Fixing the hand strap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Symbols and readings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Fitting the mouthpiece . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Switching on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Switch on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Switch off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Automatic switch off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Performing the Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Requirements of the person to be tested . . . . . . . . . . . . . . . . . . . . . 10
Further measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Removing the mouthpiece . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Symbols on the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Quick menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Set mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Measuring limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Factory settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Maintenance intervals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Changing batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Disposal of the instrument . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Waste electrical and electronic equipment . . . . . . . . . . . . . . . . . . . . 23
Fault, Cause, Remedy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Order list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
2
For your safety
Strictly follow the instructions for use
Any use of the instrument requires full understanding and strict observation of these instruc­tions. The instrument is only to be used for the purposes specified herein.
Maintenance
Maintenance must only be performed by experts. We recommend that a service contract be obtained with Dräger Safety and that all repairs be carried out by them. Only authentic spare parts may be used for maintenance. Observe chapter "Maintenance intervals".
Accessories
Only the accessories specified in the order list may be used.
Liability for proper function or damage
The liability for the proper function of the instrument is irrevocably transferred to the owner or operator to the extent that the instrument is improperly serviced or repaired by personnel not employed or authorized by Dräger Safety or if the instrument is used in a manner not conform ing to its intended use. Dräger cannot be held responsible for damage caused by non-compliance with the recom­mendations given above. The warranty and liability provisions of the terms of sale and delivery of Dräger are likewise not modified by the recommendations given above.
-
Dräger Safety AG & Co. KGaA
-------------------------
® Alcotest is a registered trademark of Dräger.
3
Intended use
For quick measurement of a person’s alcohol intoxication through measurement of the breath alcohol concentration. For mobile use with batteries.
Preparation
Alcotest® 6810 GB is supplied with standard calibration by the manufacturer. The date of the last calibration can be found in the quick menu (page 18).
M
OK
Alcotest 6810
00123973_1.eps
4
What‘s what?
Measuring instrument
1 Display
2 Menu button "UP"
3 "OK" button
4 Menu button "DOWN/MENU"
5 Communication port
6 Indicating LED
7 Mouthpiece receptacle
7
6
1
4
M
OK
Alcotest 6810
2 3
5
00223973_1.eps
5
Preparation
Inserting the batteries
Upon initial operation or if the battery symbol on the display indicates "empty".
Gently press onto the lock of the battery compartment and remove cover.
Observe correct polarity when inserting the batteries!
Close battery cover.
05623973_1.eps
00423973_1.eps00523973_1.eps
Batteries to be used
2 each 1.5 V Type Alkaline (Mignon, LR6, AA)
6
+ +
Fixing the hand strap
Insert the smaller loop into the hole in the housing.
Thread the longer loop through the eyelet and pull through.
Symbols and readings
The breath alcohol value is measured in μg/100 ml. The result is displayed as
"ZERO", PASS", "ALERT" or "FAIL". For threshold limits see page 20.
Symbols
In these instructions for use several symbols are used corresponding to the messages indicated on the display:
Battery symbol
Indicates the battery charging status:
OK
Alcotest 6810
00923973_1.eps
Full battery
Battery capacity 2/3
Battery capacity 1/3
Empty battery
7
Note: The symbols under the battery flap mean: Attention! Please con­sult the user instructions! Before changing batteries, please read the instructions.
Buttons
OK
"OK"-button Confirms entries or selected functions. Button to switch instrument on and off.
01223973_1.eps
M
"DOWN" and "UP" Setting of values and selection of menu functions.
Fitting the mouthpiece
Open packaging. To ensure the mouthpiece stay hygienic, keep the portion to come in
contact with mouth covered by packaging until mouthpiece is correctly fitted to the instrument.
With the grooved markings facing up, press the mouthpiece into mouthpiece receptacle
until you hear it click into place.
8
05723973_1.eps05823973_1.eps
Remove packaging completely and commence breath test.
Mouthpiece can be used with orientation to right or left side.
M
OK
Alcotest 6810
Switching on and off
Switch on
Keep - button pressed for approx. 1 second until start window is displayed.
Switch off Unless the device is at "READY" you are unable to turn the device off.
Keep - button pressed.
The instrument switches off after 2 seconds.
Automatic switch off
The instrument switches automatically off 4 minutes after the last use.
OK
OK
Alcotest 6810 GB
Alcotest 6810 GB
shut-down in 2 sec.
Alcotest 6810 GB
auto - shut-down
00723973_1.eps
01323973_1_en.eps
01423973_1_en.eps
03323973_1_en.eps
9
When the batteries are discharged the instrument switches automatically off.
Performing the Measurement
Conditions
— A new mouthpiece has to be used for every person tested. — Do not apply too high alcohol concentrations onto sensor, e.g. by rinsing the mouth with
high-strength alcohol shortly before the measurement. By doing so the sensor service life is reduced.
— Keep sufficient distance to the antennas of mobile phones and transmitting stations.
Requirements of the person to be tested
— Maintain a waiting period of at least 20 minutes after drinking alcohol!
Residual alcohol in the mouth can distort the measurement. Aromatic drinks (e.g. fruit juice), mouth sprays containing alcohol, medicines can interfere with measurements. Rinsing the mouth with water or non-alcoholic drinks does not reduce this waiting period!
— Before sampling the person to be tested must breathe normally. Quick inhaling and
exhaling through the mouth must be avoided.
— The person to be tested must provide the required minimum air volume of 1.2 L (factory
setting). The exhaling breath flow must be constant for at least 2 seconds.
Preparation
Insert new mouthpiece in the holder (page 8).
Switch instrument on (page 9).
Followed by the user defined screen. If the date for next service is expired:
Unit has to be accuracy checked (see “Fault, Cause, Remedy” on page 24).
10
Alcotest 6810 GB
18.01.2007 12:00
Calibration in: XX days Acc. Check in: XX days
Temperature: 22
o
C
Policestation 1
01323973_1_en.eps
03623973_en.eps
07023973_en.eps
After 2 seconds: the info screen or "WAIT" is indicated on the display.
The info screen can also be viewed by pressing the - button.
Close with the - button.
OK
— The instrument starts in the "ROAD" mode.
To select other transport modes press the - button while
M
"ROAD" is displayed (see page 18).
The following inputs are required to perform the test: — Reason code
to select the reason code press the - button or
the - button.
to confirm the reason code press twice the - button.
M
OK
— Subject age
to select the subject age press twice the - button and
the - button.
to confirm the subject age press twice the - button.
M
OK
— Subject gender
to select the subject gender press the - button or
the - button.
to confirm the subject gender press twice the - button.
M
OK
WAIT
Test Reason
RTC
Subject Age
0 0
Subject Gender
Male
01523973_1_en.eps
00623973_en.eps
01923973_en.eps
02423973_en.eps
ROAD
Test Reason
OK
Subject Age
OK
Subject Gender
04123973_1_en.eps
RTC
01123973_en.eps
0 0
02123973_en.eps
Female
02323973_en.eps
Subject Gender
Unknown
02223973_en.eps
OK
Subject Gender
Male
04023973_en.eps
11
The following limits are activated for the different modes:
AIR: ROAD:
ZERO: < 4μg/100 ml ZERO: < 4μg/100 ml PASS: 9μg/100 ml PASS: < 31μg/100 ml FAIL: > 9μg/100ml ALERT: 35μg/100ml
MARINE: RAIL:
ZERO: < 4μg/100 ml ZERO: < 4μg/100 ml PASS: < 31μg/100 ml PASS: < 31μg/100 ml ALERT: 35μg/100ml ALERT: 35μg/100ml FAIL: 36μg/100 ml FAIL: 36μg/100 ml
Set mode see page 18.
As soon as the information is entered "READY", "R.AIR", "R.MARINE" or "R.RAIL",is displayed and a short audible signal is given. At the same time the current test number is indicated. The green light flas hes. The instrument is ready for measurement.
FAIL: 36μg/100 ml
-
READY
Test No. XXXXX
01623973_1_en.eps
R.AIR
Test No. XXXXX
07123973_1_en.eps
12
R.MARINE
Test No. XXXXX
07223973_1_en.eps
R.RAIL
Test No. XXXXX
07323973_1_en.eps
Performing the measurement
Ask the test subject to blow evenly into the mouthpiece without interruption. A sufficient
flow is indicated by a continuous tone and a green light.
While the sample is taken the display shows: "Blow"
When the sampling was successful the green light is going to cease and the continuous tone is going to stop. The display shows:
"WAIT Analyzing"
Test result
After 5 to 25 seconds (depending on the instrument temperature and the measured concen­tration) the measured value is shown on the display. ZERO / PASS
or ALERT (in ROAD mode only)
or FAIL
It is also possible to show the value in a decimal presentation, if required by respective autho­rities. Once the result is shown, this part of the test data is already stored.
Blow
WAIT
Analyzing
ZERO
PASS
ALERT
FAIL
0
μg/100 ml
01723973_1_en.eps
01823973_1_en.eps
06823973_1_en.eps
06223973_1_en.eps
06723973_1_en.eps
06323973_1_en.eps
06423973_1_en.eps
13
Error in delivering the breath sample
If the sampling volume is too low the display shows:
"Insufficient Volume"
The horn sounds briefly and a red light flashes.
If the subject is unable or unwilling to provide a sample press the
-button to complete the test with "REFUSAL" as result and confirm
by selection with YES". "NO" cancel the "REFUSAL".
To repeat press the - button. The instrument is ready for measure-
OK
ment after 4 seconds. After the test the following inputs are possible — Subject Ethnic, e.g. Asian Indian
press the - button
OK
to select the subject ethnic press the - button or
the - button.
to confirm the subject ethnic press twice the - button.
M
OK
— Officers Identity
press the - button
OK
Up to 6 digits, digit 1 and 2 alphanumeric, digit 3 to 6 only numeric.
To enter a 5 digit code use "Blank" for digit one.
enter the code by pressing the - button or
the - button.
to confirm the code press twice the - button.
M
OK
— Location of Test
press the - button
OK
enter the code by pressing the - button or
the - button.
to confirm the code press twice the - button.
M
OK
select "Next Test" or "Switch off".
YES
NO
Skip
Enter
Skip
Enter
Skip
Enter
Insufficient
Volume
OK
REFUSAL ?
Subject Ethnic
Officers Identity
Location of Test
Data saved
02023973_1_en.eps
07523973_en.eps
02823973_en.eps
03123973_en.eps
03223973_en.eps
Skip
OK
Skip
OK
Skip
OK
Subject Ethnic
W1
04223973_en.eps
Officers Identity
A 0 0 0 0
03523973_en.eps
Location of Test
0 0 0 0 0
03823973_en.eps
14
Next Test
Switch off
03423973_en.eps
Further measurement
If you select "Next Test" and press the - button a new
OK
measurement is going to be prepared. During the recovery period of the sensor (see “Technical data” on page 26) the display shows: "WAIT"
Note: Switching the instrument off in the meantime does not reduce the waiting period!
Removing the mouthpiece
Push the mouthpiece out of the mouthpiece holder.
Dispose of the mouthpiece in accordance with local regulations.
WAIT
02223973_1_en.eps
M
OK
Alcotest 6810
00823973_1.eps
15
Menu
Activation
Switch instrument on. While "WAIT", "ROAD", "READY" or "R.AIR" appears on the display
the menu functions can then be called up.
For quick menu press button shortly.
M
— After leaving menu the data input routine starts again, incomplete tests are not stored. — The main menu is accessible to instrument supervisors only.
Operation
— Select functions using and buttons.
— The selected function is highlighted.
— Activate the selected function by pressing - button.
— Selecting " back to measurement" and pressing the
- button brings the instrument into the measuring mode.
OK
If no button is pressed within 120 seconds. The instrument automatically returns to the meas­uring mode.
M
OK
16
Symbols on the display
Menu
Return to next higher menu level
Menu item with sub-menu
Open menu item
Selected function
Further items below the visible items
Further items above the visible items
Function
Activated item
Actual screen (1) of all screens (6)
17
Quick menu
Last tests
Display of the last test. Back with - button.
OK
Last cal. date
Display of last calibration date. Back with - button.
OK
Set mode
Display for selection of the two different modes: — ROAD, "ZERO" / "PASS" / "ALERT" / "FAIL". — AIR, "ZERO" / "PASS" / "FAIL". — MARINE, "ZERO" / "PASS" / "ALERT" / "FAIL". — RAIL, "ZERO" / "PASS" / "ALERT" / "FAIL".
Set contrast
Change by pressing and . Back with - button.
M
OK
Accuracy check
Confirm proper measuring operation.
Accuracy check
To perform an accuracy check before the expiry date has been reached, a download and clearing of the memory must be performed. An "Accuracy Check Error" will be displayed if a download and clearing has not been completed prior to the accuracy check being attempted.
If the "Expired time" screen appears then before an accuracy check can be performed. The instruments memory must always be downloaded and cleared using Dräger AlcoView Software before performing an accuracy check.
Back to measurement
Last tests
Set contrast Last cal. date Set mode Accuracy check
18.01.2007 12:00
Service required
Accuracy check
Temperature: 22
o
C
02623973_1_en.eps
07423973_1_en.eps
The calibration parameters are not changed with this procedure!
Enter the "Accuracy check" item by using the - button. The display shows the calibration
OK
gas to be used. Enter "Next" item by using the - button.
OK
18
Accuracy check
Back to menu Check value: 35 μg/100 ml Gas Type: Dry gas
Next
06523973_1_en.eps
When "Supply gas" is shown supply respective gas. A minimum flow rate of 3 L/min obtain "Gas flow ok" on display. The instrument automatically performs the check. The result is displayed together with the check value.
Set mode
Enter "Set mode" item by using the - button.
Change by pressing or and choose with - button.
M
OK
OK
XXXX: according to local settings
Back by enter the "Back to menu" item by using the - button.
OK
Check value : 47.6 Result : 47.0 Unit : μg/100mL
Set mode
Back to menu GB Road GB Air GB Marine GB Rail
06923973_1_en.eps
06623973_1_en.eps
19
Measuring limits
Limit
Set mode μg/100 mL
<4
μg/100 mL
9
μg/100 mL
<31
μg/100 mL
<36
μg/100 mL
36 AIR ZERO PASS FAIL FAIL FAIL ROAD ZERO PASS PASS ALERT FAIL MARINE ZERO PASS PASS ALERT FAIL RAIL ZERO PASS PASS ALERT FAIL
Displaymode
alcohol indication
Factory settings
ROAD AIR MARINE RAIL ZERO: <4 μg/100 mL ZERO: <4 μg/100 mL ZERO: <4 μg/100 mL ZERO: <4 μg/100 mL PASS: <31 μg/100 mL PASS: 9 μg/100 mL PASS: <31 μg/100 mL PASS: <31 μg/100 mL ALERT: 35 μg/100 mL FAIL: >9 μg/100 mL ALERT: 35 μg/100 mL ALERT: 35 μg/100 mL FAIL: 36 μg/100 mL FAIL: 36 μg/100 mL FAIL: 36 μg/100 mL
Error
In case of internal error, the following error message is displayed.
If the failure still occurs after the instrument is switched on and off several times. Contact Dräger Safety.
20
Internal System ERROR
662
05523973_1_en.eps
Maintenance
Maintenance intervals
If necessary:
Changing batteries, page 22.
Every month:
Check calibration.
Storage
The Alcotest
Therefore remove the batteries from the instrument during long periods without use.
Note: In case of long storage periods Remove batteries from instrument, if the instrument is not used for more than 6 months to avoid damage to the instrument caused by leaking battery acid.
Caution: Used alkaline batteries must not be thrown into open fire, be recharged or opened by exerting force. Danger of explosion!
®
6810 GB consumes a small amount of current even when switched off.
— Only dispose of as special waste in accordance with local waste disposal regulations.
For more information about suitable waste disposal companies please contact the local authorities for environmental protection.
21
Cleaning
Do not submerge in liquid – liquid must not enter the sockets!
To clean: — wipe with a disposable tissue.
do not use cleaning agents containing alcohol or solvents.
Changing batteries
If the battery symbol on the display indicates "empty", change the batteries.
Gently press onto the lock of the battery compartment and remove cover.
Remove used batteries and insert new ones – consider correct polarity.
Close battery cover.
Required batteries:
2 each 1.5 V Type Alkaline (Mignon, LR6, AA)
00423973_1.eps00523973_1.eps
+ +
— For continuity of use it is recommended always to have replacement batteries or an
additional battery supply available.
22
Caution: Used batteries — Do not expose to fire, — Do not recharge, — Do not force open. Danger of explosion!
Only dispose of as special waste, in accordance with local waste disposal regulations. Infor­mation can be obtained from environmental agencies and from waste disposal companies.
Disposal of the instrument
— at the end of its service life.
Dispose of the instrument in accordance with national waste disposal regulations
or
Ask a suitable disposal contractor to dispose of the instrument.
The local environmental agency can supply further details.
Waste electrical and electronic equipment
EU-wide regulations for the disposal of electric and electronic appliances which have been defined in the EU Directive 2002/96/EC and in national laws are effective from August 2005 and apply to this instrument. Common household appliances can be disposed of using special collecting and recycling facilities. However, as this instrument has not been registered for household usage, it must not be disposed of through these means. The instrument can be returned to your national
Safety Sales Organization for disposal. Please do not hesitate to contact the above if
Dräger you have any further questions on this issue.
23
Fault, Cause, Remedy
Fault Cause Remedy
Instrument switches automatically off. batteries discharged. replace batteries, page 22.
Instrument has been left ready for measure­ment for more than 4 minutes.
Instrument automatically leaves menu-mode and shows measuring mode.
Instrument cannot be switched on. batteries discharged. Replace batteries. Insuffient volume. Subject not blowing hard or evenly enough. Ask to blow harder and more evenly.
Fault in display Cause Remedy "Calibration error" Calibration not successful. Calibrate again, by trained service personnel,
"Accuracy check error" Accuracy check not successful. Repeat accuracy check, if fault reappears,
Instrument has an automatically switch off of the menu after 120 sec. without use.
BAC measured exceeds measuring limits. Use lower concentrations.
Reselect menu item.
e. g. by Dräger
call Dräger
Safety.
Safety.
"Internal System ERROR"
with service code
24
Instrument error, no measuring function pos­sible.
Remove batteries (2 sec.) and insert them again, if the fault reappears call
Service.
Dräger
WARNING Fault in display Cause Remedy
"Accuracy check overdue lockout in X days"
"Service required Accuracy check"
Accuracy check intervall expired. Device is useable until graceperiode is expired.
Download and clear datalogger. Perform accuracy check.
Accuracy period expired. Download and clear datalogger. Perform
accuracy check.
"Service date expired / accuracy check" Service date expired Download and clear datalogger. Perform
accuracy check.
"Calibration overdue lockout in X days" Calibration intervall expired. Device is usea-
ble until graceperiode is expired.
"Service required
Calibration period expired. Perform calibration by trained service person-
Calibration"
Perform calibration by trained service person­nel, e. g. by Dräger Safety.
nel, e. g. by Dräger Safety.
"Service date expired / calibration" Service date expired Perform calibration by trained service person-
nel, e. g. by Dräger Safety.
"Memory for XXTests" Device only useable for X tests. Transfer memory data to PC. Clear memory.
25
Technical data
Measuring principle Electrochemical sensor
Measurement range
Breath alcohol concentra­tion
Display range
Display range is identical to measuring range. If the result is exceeding the measuring range the display will show three arrows "
Ambient conditions
For operation 0 to 40 oC (32 to 104oF)
For storage –40 to 65 oC (–40 to 149 oF)
Sample conditions
minimal blowing time 2 s default
minimal volume 1.2 L default
0 to 250 μg/100mL (Ethanol-Mass per breath volume at
o
C and1013 hPa.)
34
↑↑↑↑ ↑↑↑↑ ↑↑↑↑" as overflow indication.
10 to 100 % r.h. (non condensing) 600 to 1400 hPa
26
Measurement accuracy
Reproducibility with an ethanol standard
up to 50 μg/100 mL 0.8 μg/100 mL or 50 μg/100 mL 1.7 % of measurement value
the higher value is valid up to 1.00 ‰ 0.017 ‰ or 1.00 ‰ 1.7 % of measurement value
the higher value is valid
Sensitivity drift typically 0.6 % of meas. value/month
Intervals before readiness for operation
1st measurement about 6 s after terminating a result of a previous test in range:
(breath alcohol unit) 25 μg/100 mL 120 s 50 μg/100 mL 140 s 100 μg/100 mL 180 s > 150 μg/100 mL 120 s
Dimensions 140 mm x 80 mm x 35 mm (W x H x D)
Weight approx. 195 g
Electrical supply
Batteries 2 x 1.5 V Type Alkaline
CE-marking electromagnetic compatibility
(Mignon, LR6, AA)
approx. 1500 measurements
(Directive 89/336/EEC)
27
Order list
Name and Description Part no. Alcotest® 6810 GB 83 18 570 Order number GB (33 10 860)
Accessories
Mouth-pieces hygienically tested
100 pieces 250 pieces 1000 pieces
Alkaline battery (1 piece) 13 35 804 Rechargable battery NiMH (1 piece) 18 90 092 Set rechargeable battery, for rechargeable bat-
teries
Case for Alcotest® 6810 GB 83 17 920 Leather pouch for Alcotest® 6810 GB
(belt fixation)
Leather pouch for Alcotest® 6810 GB (yellow)
(Instrument can be operated while staying in the pouch)
Power supply 83 16 991
PC-Communication-cable RS 232 83 17 593 PC-Software AlcoView 83 17 915
68 10 690 68 10 825 68 10 830
83 18 565
83 17 911
83 17 931
28
Index
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3, 28
Accuracy check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Ambient conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Automatic switch off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Battery symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
CE-marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Changing batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Display range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Disposal of the instrument . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Electrical supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14, 20
Factory settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Fault . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Fault in display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24, 25
Further measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Hand strap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Intervals before readiness for operation . . . . . . . . . . . . . . . . . . . . . 27
Last cal. date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Last tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Liability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3, 21
Maintenance intervals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Measurement range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Measuring instrument . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Measuring limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Measuring principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
mobile phones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Mouthpiece . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8, 15
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Order list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Performing the Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Performing the measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4, 6
Quick menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Readings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Removing the mouthpiece . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Required batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Residual alcohol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
29
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Sample conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Sensitivity drift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Set contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Set mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18, 19
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Switching off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Switching on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Symbols on the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Test result . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
transmitting stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
30
Dräger Safety AG & Co. KGaA
Revalstraße 1 D-23560 Lübeck Germany
+49 451 8 82- 0
Tel. Fax +49 451 8 82- 20 80 www.draeger.com
90 23 973 - GA 4754.500 en © Dräger Safety AG & Co. KGaA 2nd edition - August 2007 Subject to alteration
Loading...