Mini FPV
LOBIT 100F
Please read the instruction manual carefully before use.
Vol 1.0
Ages 14+
Intro
Thank you for purchasing DROGEN products. DROGEN LOBIT 100F is designed as an easy-to-use,
full-featured RC model, capable of hovering and aerobatic flight maneuvers.
Please read the instruction manual carefully and follow all the instructions.
Be sure to retain the manual for future reference, routine maintenance and tuning.
Safety Notes
· Be cautious that this product is not designed for children under 14 years of age.
· Improper use of this product will result in serious injury.
Be aware of your personal safety, safety of others and your surrounding environment.
· Keep Lobit out of reach of children.
· It is recommended that beginners learn to fly with more experienced pilots before attempting
to fly LOBIT 100F for the first time.
· Do not operate LOBIT 100F near buildings, crowds of people, or trees to ensure the safety
of yourself, others and your LOBIT 100F.
· LOBIT 100F contains many precision electrical components.
Store the battery and Lobit in a dry area at room temperature. Exposure to water or moisture
may cause malfunction resulting in loss of responsiveness, or a crash.
· For safety, only use the included DROGEN spare parts for replacement.
· When in operation, propellers will be spinning at high speed.
The propellers are capable of inflicting serious injury or damage to property.
Be careful to keep your body and loose clothing away from the propellers.
· Never take your eyes off LOBIT 100F or leave it unattended while it is turned on.
Stop operating immediately if LOBIT 100F flies out of your sight.
· Radio interference may occur while using radio equipment
· Frequency is selectable. In case there is any interference, you can change the
setting from the range 5725 to 5825 MHz.
Frequency (MHz) :
2400~2483.5
5725~5825
Radio Wave Type :
F(G,D)1(2,7)C(D,E,F,W)
A2(7,9) F(W) F9W
Safety checks before flying
Carefully check all the parts of LOBIT 100F. Broken parts will pose a risk of injury and hazard.
If any problem is found before flight, do not fly LOBIT 100F. Check with call centers and local
agencies.
· Before operating, check that the batteries of the transmitter and LOBIT 100F are charged for
the flight.
· Before turning on the transmitter, check that the throttle stick is pulled completely down.
· Check the battery and power plug are securely fastened.
Severe vibration during flight may detach the plug and result in loss of control.
· When turning on LOBIT 100F, always turn on the transmitter first and then turn on LOBIT 100F.
Also, when turning off LOBIT 100F, always turn off LOBIT 100F first and then turn off the transmitter.
- 1 -
Safety advisory notice for
Lithium-Polymer(Lipo)Batteries
Lipo batteries are different from conventional batteries in that their chemical contents
are encased in a relatively lightweight foil packaging.
This has the advantage of significantly reducing their weight but it does make them more
susceptible to damage if roughly or inappropriately handled.
As with all batteries, there is a risk of fire or explosion if safety practices are ignored.
· Charge and store Lipo batteries in a location where a battery fire or explosion
(including smoke hazzard) will not endanger life or property.
· Keep Lipo batteries away from children and animals.
· Never charge the Lipo battery that has ballooned or swelled.
· Never charge the Lipo battery that has been punctured or damaged.
· After a crash, inspect the battery pack for signs of damage.
Discard in accordance with your country’s recycling laws.
· Never charge the Lipo battery in a moving vehicle.
· Never overcharge the Lipo battery.
· Do not charge Lipo batteries neat flammable materials or liquids.
· Ensure that charging leads are connected correctly.
Reverse polarity charging can lead to battery damage or a fire or explosion.
· Have a suitable fire extinguisher (electrical type) or a large bucket of dry sand near
the charging area. Do not try to extinguish electrical (Lipo) battery fires with water.
· Reduce risks from fire /explosion by storing and charging Lipo batteries inside a suitable container.
· Protect your Lipo battery from accidental damage during storage and transportation.
(Do not put battery packs in pockets or bags where they can short circuit or can come into
contact with sharp or metallic objects.)
· If your Lipo battery is subjected to a shock (such as a crash),place it in a metal container
and observe for signs of swelling or heating for at least 30 minutes.
· Do not attempt to disassemble or repair the Lipo battery.
Lipo Battery Disposal & Recycling
Lithium-Polymer(Lipo) batteries must not be placed in with
household trash. Please contact your environmental or waste
agency or the supplier of your model for local regulations
and the location of your nearest Lipo battery recycling center.
- 2 -
Charging the Lipo battery
3.7V 520mAh Lipo Battery
How to charge : Connect USB slot with USB charger,
then connect the USB charger to a computer
or other USB connector, such as a
smart phone charger.
The LED lights up while charging
and turns off when charging is
complete.
The voltage of the USB is +5±0.5V.
The charging time is around 40 mins
and the flying time is around 6 mins.
· Take out the battery with the battery compartment
when you storage it.
· Always power off LOBIT 100F when you charge
the battery.
Safety Advisory Notice for storing Lipo battery
Always partially charge your Lipo battery before storage.
Lipo batteries retain the power over a reasonable period.
It is not normally necessary to recharge stored Lipo batteries unless stored for periods longer
than 3-6 months. If the battery runs down, replace it.
- 3 -
MODE 1 Transmitter
Main Menu
Video glasses socket
Earphone socket
Elevator / Rudder Stick
Input Key Function
Throttle
/ Aileron Stick
Elevator
/ Rudder Stick
Aileron Trim
LCD
Photo
Elevator Trim
Rudder Trim
On time
Elevator trim
Rudder trim
Move the stick forward or backward to make LOBIT 100F ascend or descend.
Move the stick left or right to make LOBIT 100F roll left or right.
Move the stick forward or backward to make LOBIT 100F move forward and
move backward. Move the stick left or right to make LOBIT 100F yaw left or right.
Aileron trim adjusts for left and right drift.
0:08:49 M1
Video
Throttle Trim
Throttle/Aileron stick
Aileron Trim
Power SW
Transmitter
Battery volcage
Throttle trim
Ailerontrim
Micro SD Slot
Earphone socket
Elevator Trim
Rudder Trim
Throttle Trim
Power Switch
Photo/Video
USB socket Only for engineer to upgrade the software , please do not use it to connect to computer.
Video glasses socket Connect video glasses (not included, needs to be purchased).
Earphone socket
Elevator trim adjusts for forward and backward drift.
Rudder trim adjusts for drift of left and right rotation or yaw.
Throttle trim is normally left at neutral. The lower trim turns LEDs on and off.
Push to ON to turn on the transmitter. Push to OFF to turn off.
Press photo button to shoot a photo. Press video button to start recording videos
and press again to stop recording.
Connect earphone after we upgrade the transmitter, now there is no voice
transmission.
- 4 -
MODE 2 Transmitter
Main Menu
Video glasses socket
Earphone socket
Throttle/Rudder Stick
Input Key Function
Throttle
/ Rudder Stick
Elavator
/ Aileron Stick
Aileron Trim
LCD
Photo
Throttle Trim
Rudder Trim
On time
Throttle trim
Rudder trim
Move the stick forward or backward to make LOBIT 100F ascend or descend.
Move the stick left or right to yaw LOBIT 100F.
Move the stick forward or backward to make LOBIT 100F move forward and
move backward. Move the stick left or right to make LOBIT 100F roll left or right.
Aileron trim adjusts for left and right drift.
0:08:49 M2
Video
Elevator Trim
Elevator/Aileron Stick
Aileron Trim
Power SW
Transmitter
Battery volcage
Elevator trim
Ailerontrim
Micro SD Slot
Earphone socket
Elevator Trim
Rudder Trim
Throttle Trim
Power Switch
Photo/Video
USB socket Only for engineer to upgrade the software , please do not use it to connect to computer.
Video glasses socket Connect video glasses, which not included and need purchase
Earphone socket
Elevator trim adjusts for forward and backward drift.
Rudder trim adjusts for drift of left and right rotation or yaw.
Throttle trim normally left at neutral. The lower trim turns LEDs on and off.
Push to ON to turn on the transmitter. Push to OFF to turn off.
Press photo button to shoot a photo. Press video button to start recording videos
and press again to stop recording.
Connect earphone after we upgrade the transmitter, now there is no voice
transmission
- 5 -
Changing mode and
transmitter stick calibration
You can change the mode as you like by following the instructions below.
STEP
1
STEP
2
STEP
3
MODE 2
Push both sticks to the upper
left position and hold.
Then power on the transmitter.
MODE 1
Push the left stick to the upper left position
and right stick to the upper right position
and hold, then power on the transmitter.
MODE 1 / MODE 2
Rotate both sticks twice.
MODE 1 / MODE 2
Hold down any trim until the LED on
the transmitter blinks red, indicating a
successful calibration.
- 6 -
Transmitter battery installation
AA batteries according to the correct polarities.
!
Notice
+
ㅡ
ㅡ
+
+
ㅡ
AA
ㅡ
AA
+
+
ㅡ
AA
ㅡ
AA
+
· Do not mix old and new batteries.
· Do not mix different types of batteries.
· Do not charge non-rechargeable batteries.
· The video will stop when the transmitter battery is low.
· When the SD card is full, it can’t record anymore and the screen will display “SD Full”.
· It is best to use a 4G+, and class 4+ SD card. Format in the transmitter before use.
· When the power on the transmitter is low, the red LED will blink quickly
and the LCD screen will turn black. The transmitter and LOBIT 100F will not bind
if the batteries are low. Please replace with new batteries.
· If the batteries in the transmitter are running low while flying the LOBIT100F,
you will still have control.
Please land the LOBIT100F and then replace batteries in the transmitter.
- 7 -
Frequency Selectable
Your transmitter will automatically find the best frequency to ensure the quality live video
transmission. In case there is any interference in your location, you can change the setting
from the range 5.725 to 5.875 Ghz to get longer range and better video transmission.
Pull down the throttle stick and press the elevator stick for about 1 second to open the setup menu.
0:08:49
0:08:49
M2
MAIN MENU
Play Record
Set Real Time
Format SD Card
Set Reverse
Set Sensitive
5.8G Frequence
Exit
M2
5.8G FREQUENCE
Exit
5.8 10MHz
▶
▶
▶
▶
▶
▶
▶
▶
▶◀
Play Record · Set Real Time · Format SD Card
These three functions will not work on LOBIT 100F as they are for other drones.
- 8 -
Camera recoding
Always power off the LOBIT 100F before inserting or removing the SD card. Always stop
the video recording function and power off the battery first, and then you can take out
the SD card.
Use Power button to Record Videos
Press the button on the side of the LOBIT 100F(near the SD card slot) to start recording.
A red light inside the SD card slot will blink and the two red LEDs on the LOBIT 100F will blink
alternately when recording starts.
Press the button again to stop recording. The red lights will stop blinking and the video
will be saved.
SD
CARD
!
Notice
· Pressing the power button for 2 seconds will power off the LOBIT 100F.
· Carefully and properly orient the SD card for insertion in the LOBIT 100F
(see the picture above). Avoid removing the SD card and re-inserting
again too quickly otherwise the recording module will not work properly.
· First format the SD card in computer by connecting the quadcopter
with the USB cable or use SD card reader.
- 9 -
0:08:49
M2
0:08:49
M2
Use Transmitter button to record videos / Take photos
You can also start recording/ taking photos by using the transmitter buttons. See below.
Photo
button
PHOTO
00008
18523
Press photo button. The blue numbers
are displayed in the bottom of the screen
and the red LEDs will blink one time.
The first line means the number of photos
shooted. The second line indicates
the left space for photos.
!
Notice
Video
button
RECORD
00 : 00 : 01
Press the video button. The red recording
time is displayed in the bottom of the screen
when recording is started and the red LEDs
on LOBIT 100F will blink alternately.
Press the video button again. The white time
Indicates the left recording space.
· Power off both the transmitter and the LOBIT 100F before inserting or removing the SD card.
· lf you don’t want to save the video, just power off the LOBIT 100F before you press
the button again.
Play the Record
You can play the videos or review the photos by connecting LOBIT 100F to computer with the USB
cable or use SD card reader.
- 10 -
Fly the LOBIT 100F
Power-On Safety Mode
Your LOBIT 100F transmitter is designed with a Power-On safety feature that ensures that
LOBIT 100F motor will not start unless it detects a suitable control signal when the Lipo battery
is connected.
Power
button
Power
Button
Press the power button under the LOBIT 100F.
Make sure the battery compartment pushed
into the bottom. Put the LOBIT 100F on a level
surface before flight, or the LOBIT 100F will drift.
Power on the transmitter and the red LED will blink.
Do not move any other stick or trim before
the transmitter and LOBIT 100F finish pairing,
or the LOBIT 100F will drift.
The transmitter LED will turn green after pairing
is successfully completed.
Red LED
After a “beep”, the red LED on the transmitter
turns green and the red LED lights on the LOBIT 100F
turn steadily, indicating successful pairing.
Low Battery Alarm : The two red LEDs will blink at the same time and the LOBIT 100F
will descend and land down automatically to 5 meters or lower from
the take off point when the LOBIT 100F battery is low.
- 11 -
Headless Mode
0:08:49 M2
Headless mode means the LOBIT 100F will default any direction as its head in front of
the transmitter. The blue lights on the LOBIT 100F will blink and “HEADLESS ON” shows on
the LCD screen when the LOBIT100F is in headless mode.
HEADLESS ON
Press the throttle stick briefly to switch on/ off headless mode.
Press the throttle stick to enter headless Mode , indicated by two “beeps”.
Press the throttle stick again to exit headless Mode,indicated by one “beep”.
Start / Stop the motors
When you need to stop the motors quickly you can use both stickers to stop the motors.
Please be cautious! Pushing the throttle stick all the way up for about 1~2 seconds
*
will start motors and LOBIT ascends.
You can also use the throttle stick to start / stop the motors. The LOBIT 100F will ascend
*
or descend.
Always stop the the motors before power off the transmitter. If you power off the transmitter
*
first, the motors will keep on for 3-4 minutes and the Lobit will land down slowly.
MODE 2
MODE 1
< Start the motors >
Pull the two sticks as the picture shows.
(The right stick to bottom left and the left stick to bottom right)
You can also use the throttle stick to start/stop the motors.
< Stop the motors >
Pull the two sticks as the picture shows.
(The right stick to bottom right and the left stick to bottom left)
- 12 -
Controlling transmitter sticks
To avoid loss of control, always move the transmitter sticks slowly.
*
Rudder
Throttle ThrottleElevator Elevator
Aileron Rudder Aileron
< MODE 2 > < MODE 1 >
Throttle increases /decreases the flying height of your LOBIT 100F.
LOBIT 100F can hold the altitude in the air.
Up
Down
< MODE 2 > < MODE 1 >
Push the throttle stick up and the LOBIT 100F will rise; Release the stick to the central position,
the LOBIT 100F will hover automatically and hold its altitude.
Pull the stick down and the LOBIT 100F will fall. However, the changes of barometer sensors
as well as earth magnetic field sensors may influence your Lobit's altitude.
Rudder rotates LOBIT 100F left or right.
< MODE 2 > < MODE 1 >
- 13 -
Left
Rotation
Right
Rotation
Elevator moves LOBIT 100F forward and backward.
Forward
< MODE 2 > < MODE 1 >
Backward
Aileron moves LOBIT 100F left and right.
Left
Right
< MODE 2 > < MODE 1 >
When you exit the headless mode, controls will appear reversed if the LOBIT 100F is
*
flying towards you!
- 14 -
Advanced performance setup
Reversing Channel Setup
If you would like to reverse any of the stick functions due to personal preference then follow
the instructions below. Be aware that this will change the controls back to front.
Pull the throttle stick to the lowest position. Press and hold the elevator stick for 1 second to
enter setting status, move the stick up/down to choose Set Reverse, push or exit.
Hold down the elevator stick for 2 seconds to exit.
0:08:49
Play Record
Set Real Time
Format SD Card
Set Reverse
Set Sensitive
5.8G Frequence
M2
MAIN MENU
Exit
▶
▶
▶
▶
▶
▶
▶
0:08:49
M2
Set Reverse
Elevator
Aileron
Rudder
▶Exit
◀ Normal ▶
◀ Revers ▶
◀ Rudder ▶
Sensitivity setup
If you would like to change the sensitivity of any of the stick functions, then follow Instructions
below. A higher sensitivity value will enable smaller/slower movement.
0:08:49
Play Record
Set Real Time
Format SD Card
Set Reverse
Set Sensitive
5.8G Frequence
M2
MAIN MENU
Exit
▶
▶
▶
▶
▶
▶
▶
0:08:49
M2
Set Sensitive
Exit
◀ Normal mode ▶
Elevator
Aileron
Rudder
▶
50
:
50
:
50
:
Pull the throttle stick to the lowest position. Press and hold the elevator stick for 1 second
to enter setting status, move the stick up/down to choose Set Sensitive, push the elevator stick
to the right, press the elevator/ aileron / rudder trim to set the sensitivity. Push the elevator
stick to the right to exit. Hold down the elevator stick for 2 seconds to exit the setup menu.
- 15 -
Expert Mode
In expert mode, the sensitivity can be adjusted even further (up to 100) to give the user
even more ability to maneuver the aircraft. Follow instructions below to switch this on/off.
Pull the throttle stick to the lowest position.
Press and hold the elevator stick for 1 second to enter setting status, move the stick up / down
to choose Set Sensitive, push the elevator stick to the right, choose Normal mode,
push the elevator stick to the right to enter into the expert mode, press the elevator/ aileron
/ rudder trim to set the sensitivity. Push the elevator stick to the right to exit this set.
Hold down the elevator stick for 2 seconds to exit.
0:08:49
M2
MAIN MENU
Play Record
Set Real Time
Format SD Card
Set Reverse
Set Sensitive
5.8G Frequence
Exit
▶
▶
▶
▶
▶
▶
▶
0:08:49
M2
Set Sensitive
▶Exit
◀ Normal mode ▶
Elevator
Aileron
Rudder
50
:
50
:
50
:
Aerial flip
Press and hold down the throttle stick for 1 second to enter flip mode, indicated by “beeps”.
The beeps will last for 2 seconds. In this 2 seconds, push the accordance sticks to perform the flips.
- Left Flip Push the aileron stick to the left. Release the stick to the center position after the flip.
< MODE 2 > < MODE 1 >
- 16 -
- Right Flip Push the aileron stick to the right. Release the stick to the center after the flip.
< MODE 2 > < MODE 1 >
- Forward Flip Pull the elevator stick forward. Release the stick to the center after the flip.
< MODE 2 > < MODE 1 >
- Backward Flip Push the elevator stick backward. Release the stick to the center after the flip.
< MODE 2 > < MODE 1 >
When the LOBIT 100F battery is low, performing flip is not possible.
*
- 17 -
Replacing propellers
The LOBIT 100F propellers are not identical. Each propeller is labeled with an 「A」 or 「B」.
When installing replacement propellers, be sure to install as shown below.
The LOBIT 100F will not fly but will flip and crash If the propellers are not installed correctly.
A
A
A
B
B
B
Remove Propellers : Hold the propeller, insert the U wrench under the propeller,
pull up and the propeller will easily come off the motor shaft.
Install Propellers : Pinch the propeller hub, align the hole to the motor shaft
and press straight down firmly but gently.
- 18 -
<-- U wrench
Exploded View
19
5
14
11
1313
14
4
18
20
9
4
1
15
5
8
16
7
17
12
6
3
2
10
22
8
- 19 -
No.
Part Name QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
PCBA Receiver board
5.8GHz TX camera module
720P camera module
820motors(clockwise)
820motors(counterclockwise)
Lipo battery (3.7V 529mAh)
FFC video cable
RedLED light cable
Blue LED light cable
5.8GHz antenna
Upper shell
Lower shell
Black Propeller A
Black Propeller B
Barometer sponge
Battery compartment cover
1
1
1
2
2
1
1
2
2
1
1
1
2
2
1
1
17
18
19
20
21
22
Battery compartment
Transparent LED hood
Motor upper rubber set
Motor lower rubber set
Screw
Screw
- 20 -
1
4
4
4
4
8
Troubleshooting
1. Transmitter and LOBIT 100F do not pair.
Power on the LOBIT 100F after the transmitter shows “Bind to Plane”.
Bring the transmitter close to LOBIT 100F during biding. Make sure you do not move
the transmitter sticks or trim during initial power-on.
2. Transmitter LED suddenly goes out.
Replace the AA batteries in the transmitter.
3. Trasmitter display is not showing the setting interface after holding down the Elevator stick
for2 seconds.
The throttle stick needs to be in the fully down position.
4. Gyro is not working well.
( 1 ) Battery voltage is too low.
( 2 ) Pair the LOBIT 100F with the transmitter again.
( 3 ) Land the LOBIT 100F with the throttle stick in the fully down position for 3 seconds and
then take off again.
5. LOBIT 100F won’t perform flips.
( 1 ) Press and hold down the throttle stick for 1 second to enter into flip mode.
Do the flip when the transmitter “beeps”.
( 2 ) Lipo power is too low. Recharge the LOBIT 100F.
6. LOBIT 100F is shaking and making noise.
Check that the motors, canopy, body and propellers are all properly positioned.
Black
White
Red
Blue
< Top View > < Bottom View >
- 21 -
Blue
Black
Red
White
7. Can not take off.
( 1 ) Make sure the propellers are installed correctly.
The propellers are marked with “A”(clockwise) and “B”(counterclockwise).
Refer to the Top View picture below for the correct orientation.
( 2 ) Make sure that each motor is installed correctly. There are two different motors with
different motor wire colors. Refer to the Bottom View picture below for the correct order.
8. Removing and installing LEDs
Removal : Unscrew and remove the upper shell and the motors.
Then desolder the thinner LED wires.
Instalation : Solder the red/ blue wire onto the anode / positive (+) lead of the LED,
and the black wire on to The cathode / negative (-) lead of the LED.
Press the LED wires into the leg slots, then press the motor wires Into the leg slots.
Install the upper shell by screws. You can tell apart the color of the LED lights by
the color of the LED wire; red wire is the red LED, blue wire is the blue LED.
Blue
Black
Black
Red
9. The motors do not spin freely after a crash.
Press the shaft down from the top of the propeller and motor to remove any objects,
or replace the motor.
10. One or more motors stop working.
( 1 ) Spin the propellers to see if jammed the motors, make sure the propellers can spin
normally.
( 2 ) Resolder any broken motor connections.
( 3 ) Replace the motor.
11. The Lobit 100F always drifts to one direction.
Calibrate the accelerometer as follows
( 1 ) Before calibrating the accelerometer, make sure that the propellers,
motors and body are in good condition with the battery fully charged.
Ensure that the battery compartment installed correctly.
Pair the LOBIT 100F and transmitter, then put the LOBIT 100F in expert mode.
Blue
Black
Black
Red
- 22 -
( 2 ) Set both the aileron and elevator trim to the middle so that the LCD displays 50.
< MODE 1 >
0:08:49 M1
< MODE 2 >
0:08:49 M2
Elevator trim
Elevator trim Aileron trim
Aileron trim
( 3 ) Pull the Throttle stick fully down and move the Rudder stick to the lower right position.
Quickly move the Aileron stick to the left and right repeatedly until the two headlights blink,
indicating successful calibration.
This calibration will reduce excessive drifting when doing level yaw turns.
< MODE 1 > < MODE 2 >
( 4 ) If the LOBIT 100F still drifts to one side, add a few sheets of paper(the number of sheets
will vary depending on the amount of drift)to the side of the LOBIT 100F that drifts.
The paper will help counter balance and create a level offset angle.
- 23 -
12. The video is not being saved to the SD card.
Always stop the video recording function then power off the battery, after that you can take
out the SD card. Always power off the quadcopter before inserting or removing the SD card.
This allows the memory to be properly saved to the SD card.
13. The transmitter will not power on.
Check the battery connection.
If the transmitter battery power is low, you will need to replace with new AA batteries.
First Person View(FPV)instructions
For those just starting FPV with the LOBIT 100F, please start slowly and use the following guidance.
1. Learn how to fly the LOBIT 100F and maintain control both indoors and outdoors at an altitude
no higher than 10 feet before you advance to FPV flight and higher altitudes.
A large part of being successful in FPV is training your fingers and brain to know how the model
will respond with your inputs so you can predetermine your stick movements.
It is very different to look at an LCD or goggles and determine hover, altitude and speed.
You will need to visually correlate and remember how the model reacts with stick movements
and also the differences of those movements when in no wind and windy conditions.
2. When flying indoors or outdoors, allow for plenty of free space with no couches, tables, trees
buildings or other objects that you might fly into.
A large area with soft grass is a perfect outdoor area to learn to fly.
An asphalt parking lot is a terrible place to learn to fly. It is recommended that you use safety
spotter for your FPV flights!
3. First learn to master hovering, then master flying a square or rectangular pattern by recognizing
features that are picked out before you begin your FPV flight.
- 24 -
Spare part Chart
Body Shell
Product Code : TO1F01
Blue LED
Product Code : TO1A03
5.8GHz Transmitter
Camera module
Product Code: TO1F03
Propellers
Product Code : TO1A01
Red LED
Product Code : TO1A04
Screw set
Product Code : TO1F05
Motor
Product Code : TO1A02
Receiver PCBA board
Product Code : TO1A05
Motor sleeve set
Product Code: TO1A06
Battery set
Product Code : TO1F02
Transmitter
Product Code : TO1F07
Rubber feet
Product Code : TO1A07
FFC video cable
Product Code : TO1F04
charger
Product Code : TO1A08
Crach pack
Product Code: TO1F06
U wrench
Product Code: TO1A09
- 25 -
Lipo battery charger
Product Code: TO1A10
Product warranty
Thank you for choosing LOBIT 100F.
Please read the instruction manual carefully before use.
Free repair may not be provided if you do not have this warranty.
Warnings and precautions in this instruction manual are provided to keep your safety and to prevent
any property damages. If any problem happens, please read the instruction manual.
You can also make an inquiry by visiting stores, agencies and service centers.
Damages which are made while your LOBIT 100F is being used properly as the manual instructs,
can be repaired for free under product warranty period which lasts for 3 months.
Product warranty period : 3 months after initial purchase
Inquiry : 82)70-5066-4097
Service Center : 82)70-5066-1232
Home page : www.lobit.co.kr
Company address : S-2302, IT Center,32, Songdogwahak-ro, Yeonsu-gu, Incheon, Korea
All the warnings and precautions given in the instruction manual are provided to prevent any
accidents, property damages and etc. from happening. Therefore, please read the instruction
manual very carefully before use. Keep the instruction manual where it can be easily reached
and found. If any problem is found during use, refer to the instruction manual or please make
an inquiry to agencies, vendors and service centers. If LOBIT 100F is broken while it is being
used properly as the instruction manual states, free repair will be provided under product
warranty period which lasts for 3 months.
You can make after-service inquiries to www.lobit.co.kr
- 26 -
Serial Number
WWW.LOBIT.CO.KR
- 27 -
Loading...