DRIVEN DSBLOCK User Manual
10.
11.
NOT INTENDED FOR STREET/HIGHWAY USE! FOR OFF ROAD/RACE USE ONLY!
DRIVEN REQUIRES THIS PRODUCT TO BE INSTALLED BY A CERTIFIED TECHNICIAN
9.
Locate OEM air hose leading to the airbox from the OEM plates removed.
Using supplied cap, remove hose and plug airbox.
Carefully replace airbox, fuel tank, fairings, and any other pieces removed during installation.
8.
Make sure ignition key is turned to the off position and engine is cool.
Place motorcycle on lift, rear stand, or side stand.
Locate the final destination of the new block off plates.
Carefully remove any fairings if needed.
Carefully remove fuel tank and air box.
Carefully remove any parts obstructing the OEM plates and then remove them.
Using blue Loctite, install the new block off plates using the OEM hardware,
and the OEM sealing “O rings” if present.
NOT INTENDED FOR STREET/HIGHWAY USE! FOR OFF ROAD/RACE USE ONLY!
PART#: DSB (1, 2, 3, 4, 6, 8, 10, 11, 13, 15)
(Installation Instructions)
1.
2.
3.
4.
5.
6.
7.
PART#: DSB (1, 2, 3, 4, 6, 8, 10, 11, 13, 15)
10.
11.
DRIVEN REQUIRES THIS PRODUCT TO BE INSTALLED BY A CERTIFIED TECHNICIAN
Carefully replace airbox, fuel tank, fairings, and any other pieces removed during installation.
7.
8.
9.
Using blue Loctite, install the new block off plates using the OEM hardware,
and the OEM sealing “O rings” if present.
Locate OEM air hose leading to the airbox from the OEM plates removed.
Using supplied cap, remove hose and plug airbox.
3.
4.
5.
6.
Locate the final destination of the new block off plates.
Carefully remove any fairings if needed.
Carefully remove fuel tank and air box.
Carefully remove any parts obstructing the OEM plates and then remove them.
(Installation Instructions)
1.
2.
Make sure ignition key is turned to the off position and engine is cool.
Place motorcycle on lift, rear stand, or side stand.
DRIVEN PERFORMANCE PRODUCTS
WWW.DRIVENRACING.COM
866-5-DRIVEN
DRIVEN PERFORMANCE PRODUCTS
WWW.DRIVENRACING.COM
866-5-DRIVEN
NOT INTENDED FOR STREET/HIGHWAY USE! FOR OFF ROAD/RACE USE ONLY!
11.
DRIVEN REQUIRES THIS PRODUCT TO BE INSTALLED BY A CERTIFIED TECHNICIAN
Carefully replace airbox, fuel tank, fairings, and any other pieces removed during installation.
DRIVEN PERFORMANCE PRODUCTS
WWW.DRIVENRACING.COM
866-5-DRIVEN
PART#: DSB (1, 2, 3, 4, 6, 8, 10, 11, 13, 15)
10.
7.
8.
9.
Using blue Loctite, install the new block off plates using the OEM hardware,
and the OEM sealing “O rings” if present.
Locate OEM air hose leading to the airbox from the OEM plates removed.
Using supplied cap, remove hose and plug airbox.
3.
4.
5.
6.
Locate the final destination of the new block off plates.
Carefully remove any fairings if needed.
Carefully remove fuel tank and air box.
Carefully remove any parts obstructing the OEM plates and then remove them.
(Installation Instructions)
1.
2.
Make sure ignition key is turned to the off position and engine is cool.
Place motorcycle on lift, rear stand, or side stand.
WWW.DRIVENRACING.COM
866-5-DRIVEN
DRIVEN PERFORMANCE PRODUCTS
10.
11.
NOT INTENDED FOR STREET/HIGHWAY USE! FOR OFF ROAD/RACE USE ONLY!
DRIVEN REQUIRES THIS PRODUCT TO BE INSTALLED BY A CERTIFIED TECHNICIAN
9.
Locate OEM air hose leading to the airbox from the OEM plates removed.
Using supplied cap, remove hose and plug airbox.
Carefully replace airbox, fuel tank, fairings, and any other pieces removed during installation.
PART#: DSB (1, 2, 3, 4, 6, 8, 10, 11, 13, 15)
(Installation Instructions)
1.
2.
3.
4.
5.
6.
7.
8.
Make sure ignition key is turned to the off position and engine is cool.
Place motorcycle on lift, rear stand, or side stand.
Locate the final destination of the new block off plates.
Carefully remove any fairings if needed.
Carefully remove fuel tank and air box.
Carefully remove any parts obstructing the OEM plates and then remove them.
Using blue Loctite, install the new block off plates using the OEM hardware,
and the OEM sealing “O rings” if present.
YOU MUST REPLACE REED AND GASKET! (DO NOT REMOVE)
Re-use
Remove and replace
w/ part# DSBLOCK-15
DSBLOCK-15
YOU MUST REPLACE REED AND GASKET! (DO NOT REMOVE)
Re-use
Remove and replace
w/ part# DSBLOCK-15
DSBLOCK-15
Gasket
Reed
DSBLOCK-12
DSBLOCK-12
Gasket
Reed
YOU MUST REPLACE REED AND GASKET! (DO NOT REMOVE)
Re-use
Remove and replace
w/ part# DSBLOCK-15
DSBLOCK-12
DSBLOCK-15
Gasket
Reed
YOU MUST REPLACE REED AND GASKET! (DO NOT REMOVE)
Re-use
Remove and replace
w/ part# DSBLOCK-15
DSBLOCK-12
DSBLOCK-15
Gasket
Reed
Loading...