Dri-Eaz Stealth AV3000, F568 Owner's Manual

Owner’s Manual

Stealth AV3000 Airmover

Model F568

DRI-EAZ PRODUCTS, INC.

15180 Josh Wilson Road, Burlington, WA 98233, USA

Phone: [phone] Fax: [phone] www.dri-eaz.com

The Stealth produces high velocity airflow for ventilation and

to accelerate the evaporation of moisture from structural and other materials.

Patents: http://www.LBpatents.com

READ AND SAVE THESE INSTRUCTIONS

WARNING! To reduce the risk of fire or
electric shock, do not use this fan with any
solid-state speed control device.

WARNING! Unit must be grounded. Do not
use with an extension cord. Connect only to an outlet provided
with a ground fault interrupting device.

WARNING! Never operate a unit with a damaged power cord, as
this may lead to electrical or fire hazards. If power cord is
damaged, it must be replaced by a cord of the same type and
amperage rating.

WARNING! Do not touch grills when unit is operating.
NOTICE: Keep motor dry. For indoor use only.
NOTICE: Unplug when not in use or when moving unit.
NOTICE: Do not allow children to play with or around the unit.

Be sure the unit is inaccessible to children when not attended.
NOTICE: Always operate the unit on a stable, level surface so it

cannot fall and cause injury.
WARNING! Do not alter or modify the Stealth AV3000 in any

way. Use only replacement parts authorized by Dri-Eaz
Products, Inc. Modifications or use of unapproved parts could

Fig. A: Parts Identification

create a hazard and will void the product warranty. Contact an
authorized Dri-Eaz distributor for assistance.

WARNING!

a) Do not operate any fan with a damaged cord or plug. Discard
fan or return to an authorized service facility for examination
and/or repair.

b) Do not run cord under carpeting. Do not cover cord with throw
rugs, runners, or similar coverings. Do not route cord under
furniture or appliances. Arrange cord away from traffic area and
where it will not be tripped over.

BEFORE YOU BEGIN

Warranty registration

Please visit warranty.drieaz.com to register your product.
Registration allows Dri-Eaz to better assist with operation,
maintenance, servicing of equipment, and to contact you in case
there is important safety information concerning your Dri-Eaz
product. If you determine service is required, have your
equipment model, serial number and original proof of purchase
available and call your distributor for assistance with obtaining a
return material authorization (RMA).

Inlet grill. Keep clear
of obstructions.

Carry handle

Outlet grill. Keep
clear of obstructions.

07-02189C F568 1 Dri-Eaz Products, Inc.

Hour meter.

Variable speed control

Circuit breaker re set s witc h.

Power outlet socket.

Tighten knob to secure
fan orientation.

Cord wrap. Wind cord
around housing in groove.
Secure cord with plug clip.

OPERATING INSTRUCTIONS

Dimensions
(D × W × H)

10.8 × 24.3 × 24.0 in.

27.4 × 61.7 × 61.0 cm

Units per 15 amp
circuit

Specifications are subject to change without notice. Some values

1. Unwrap the cord and plug the unit into a standard 115V

GFCI-protected outlet. CAUTION: Be sure switch is in the
off position before connecting unit to power outlet.

2. For ventilation, direct the Stealth outlet where desired. For

drying, direct the outlet toward the surface to be dried.
Secure the airmover orientation by tightening the knobs on
either side of the unit.

3. When fin ished, unplug the unit and re-wrap the cord in the

cord wrap.

Electrical safety devices

Circuit breaker: If the circuit breaker detects overload or short

circuit conditions, the breaker will automatically shut off the

Fig. B: Disassembly for cleaning

Remove the four screws as sho wn and lift off the front assembly.
Retain screws for reassembly. Do not overti ghten screws.

electrical supply. If this should occur, check the power cable
carefully for any damage and ensure it is plugged into a properly
grounded outlet. Press the Circuit Breaker Reset Switch (Fig. A)
to reestablish the electrical supply.

TRANSPORT AND STORAGE

Always use the handle to load or carry the unit.
For cord storage, wrap cord around housing in groove. Pull cord

snug and secure with plug clip (Fig. A).
Units may be stacked up to five high for transport and storage

(Fig. C). To stack, tip first unit back onto its outlet side and nest
additional units on top (Fig. A).

When transporting, secure the unit(s) carefully to prevent sliding
and damage to the unit and/or injury to vehicle occupants.

Keep unit dry. Do not expose the unit to rain or snow.

MAINTENANCE

WARNING: Unplug unit before performing any maintenance.
Before each use

Inspect the power cord. If cord is damaged, do not use. Always
grasp the plug (not the cord) to unplug.

As needed

Clean housing and impeller. If dust accumulation is visible in the
interior, remove the four screws from the outlet grill as shown
(Fig. B). Clean impeller assembly and all surface s with
pressurized air and/or with a soft cloth. Do not apply liquids to
the impeller assembly. The housing may be cleaned with a mild
solution of detergent and warm water. Ensure housing is
completely dry before reassembling.

Fig. C: Stacking for storage or transport

FOR SERVICE CALL YOUR LOCAL DISTRIBUTOR or the
Dri-Eaz Service Department at 800-932-3030.

SPECIFICATIONS

Model Stealth AV3000 (F568)
Volts 115
Frequency 60 Hz
Amp draw 2.7
Power (motor rating) 0.46 hp / 340W
Weight 27.5 lbs. | 12.5 kg

Up to 4

Air movement 2600 CFM | 4417 CMH
Static pressure (H2O) 0.40 in. | 99 Pa
Sound level (avg.) 58–72 dB
Control Variable speed rotary switch
Cord length

Construction

Safety

15 ft. | 4.6 m
Rotomolded polyethylene and injection

molded ABS housing components; steel
wire inlet and outlet grills.

PENDING: ETL tested to UL and CSA
standards

07-02189C F568 2 Dri-Eaz Products, Inc.

may be approximate.