Dri-Eaz Sahara ProX3 115V Owner's Manual

DRI-EAZ PRODUCTS, INC.

15180 Josh Wilson Road, Burlington, WA USA 98233
Fax: [phone] Phone US: [phone]
www.dri-eaz.com

Owner’s Manual

Sahara ProX3 (115V Model)

Patents:

http://www.LBpatents.com

READ AND SAVE THESE INSTRUCTIONS

WARNING

ELECTRIC SHOCK HAZARD

This unit must be electrically
grounded
Use only on GFCI protected
receptacles

The power cord is equipped with a 3­prong grounding plug. Use only with
a matching receptacle.

Do not cut off the grounding prong.
Do not use an adapter.
Do not use with a damaged power

cord.
Do not use an extension cord.
To reduce risk of fire or electric shock,

do not use this airmover with any solid

-state speed control device.

NOTE: Humidity will rise with the use of
TurboDryers because they lift moisture
from wet materials into the air. To learn
about managing humidity during drying,
contact your local distributor or call Dri­Eaz Education at 800-575-5152.

PLACING YOUR TURBODRYERS

When drying the interior of a building, use at least one TurboDryer
per water-damaged room, or one every 200 square feet. Try to get
airflow to all wet surfaces. Open interior doors to improve air circula­tion, and brace doors to prevent them from blowing shut.

WARNING

Do not move or carry a TurboDryer while under operation. When the unit
is in motion, the powerful airflow is hard to control, and can produce
rapid and unpredictable movement.

Do not allow children to play with or around TurboDryers. If they lift or
get a unit off balance, the powerful airflow can cause the TurboDryer to
move rapidly, risking injury.

Do not alter or modify your Dri-Eaz product in any way. Use only re­placement parts authorized by Dri-Eaz Products, Inc. Modifications or
use of unapproved parts could create a hazard and will void your war­ranty. Contact your authorized Dri-Eaz distributor for assistance.

OPERATING YOUR TURBODRYER

1. Locate the electrical cord and plug into a standard 3-prong outlet.

2. Set the switch to the desired speed, based on amp draw as listed
by the switch on the side control panel.

HE AUXILIARY OUTLET

T
You can “daisy chain” or interconnect up to three Sahara Pro X3 units
to customize your drying needs. The unit can conduct a maximum of
12 amps when it is turned off or 8 amps when it is turned on.

ED CIRCUIT BREAKER SWITCH

R
The primary purpose of the circuit breaker is to protect the machine. It
turns the unit off when more than 12 amps are run through the on-unit
circuit.

ROUND FAULT CIRCUIT INTERRUPTER

G
The GFCI protects the user. Should it detect a sudden “ground fault,”
the GFCI will interrupt the electric current. The GFCI will also trip
when a short circuit or overload occurs. If the GFCI “trips,” unplug the
unit and look for potential hazards (standing water, frayed cord, etc.)
that might cause an electrical surge. Relocate the unit and plug into a
different outlet. Then push the “Reset” button and check to make sure
it is operating. If so, continue use; if not, call a Dri-Eaz tech specialist
at 800-575-5152.

07-01537D F351-120V 2013-05 Warranty 07-00419 1 Dri-Eaz Products, Inc.

1

READ AND SAVE THESE INSTRUCTIONS

WARNING

ELECTRIC SHOCK HAZARD

Keep motor and electrical parts
dry.

Do not operate in standing water.
Do not expose to rain, water or

snow.
Do not get the exterior, motor or wir-

ing wet.
Do not clean with wet objects, i.e.,

power washers, soap and water, etc.
If motor or electrical parts become

wet, allow them to dry completely
before using.

Read and understand manual be­fore operating.

COOL AND VENTILATE
Place the airmover on a flat surface, and direct the air from cooler
areas (including the outdoors) into a warm room.

TURBODRYER STORAGE

Stackable

Units can be stacked (up to 3) on their sides
for storage.

NOTICE

Stacking feature is not secure enough to
be used during transport.

WARNING

Always disconnect the TurboDryer from its
power source before performing any mainte­nance or cleaning.

WARNING

FIRE HAZARD

Keep air intakes clear. Reduced

airflow can cause motor to overheat.
Clean any lint or other material

from the screens before each use.
Do not operate near draperies or

other material that could block the
air intakes.

Clean dust and dirt from motor
using a vacuum or compressed air.

Do not use or store where flamma­ble vapors like gasoline, solvents, or
thinners are present.

Do not use near open flames, or
heat sources.

Read and understand manual be­fore operating.

Preventive Maintenance

Routine maintenance can significantly increase the life of your Tur­boDryer. It also promotes efficient operation. The applications and
amount of use by owners vary, so the recommendations listed below
are for average-to-high-volume use in water damage. Constant opera­tion or use in other environments may require additional maintenance.
Contact Dri-Eaz for more information.

NOTE: Do not oil motor bearings; they are permanently oiled.

EFORE EACH USE:

B
 Inspect power cord for cuts, fraying or damage; do not use if dam-

aged.

 Remove lint or obstructions from the grills using a vacuum or com-

pressed air.

 Inspect exterior components (switch, knob, etc.) for damage.

Q

UARTERLY (OR AS NEEDED):

 Clean the exterior with a household all-purpose spray cleaner.

Spray the rag, then apply to the surface.

 To renew shine on the plastic, use a vinyl cleaner.
 Remove grill and blower, then blow off internal components with

compressed air.

A

NNUALLY:

 Inspect components and internal wiring for discoloration, loose con-

nections, or fraying.

07-01537C 2013-01 Warranty 07-00419 2 Dri-Eaz Products, Inc.

2

Important Safety Instructions:

TurboDryer from its power source before performing
any maintenance or cleaning.

Always disconnect the

TO CLEAN INTERIOR (AS NEEDED):

To remove grill and blower wheel:

1. Use a Phillips #2 screwdriver to remove 2 screws.

2. Remove inlet grill

3. Loosen the blower wheel shaft nut (3/8” socket driver)
Note the backstop for ensuring alignment when replac­ing wheel.

4. Pull the blower wheel out of the unit.

.

5

2

3

To remove control panel and motor:

Rotate the unit onto its side so that the controls are facing up.

5. Unscrew 2 screws securing cord guard (#2 Phillips screwdriver).

6. Remove cord guard.

7. Remove 4 motor mount bolts with 3/8” nutdriver.

8. Pull motor assembly out of the housing.

.

1

4

3

7

8

6

To reassemble unit:

Follow the steps above in reverse order (starting with #9).

Note: Before tightening shaft nut on wheel, ensure that bolt is aligned with flat
spot on shaft (see photo A).

07-01537C 2013-01 Warranty 07-00419 3 Dri-Eaz Products, Inc.

A

3

APPLYING YOUR UNIQUE ADHESIVE LABEL:

 Locate the smooth area on the front side of the rotomolded

housing.

 Clean the area with a standard household cleaner.
 Once dry, apply a durable label using heavy-duty adhesive.

Model Specifications

Sahara ProX3

Model F351

Height
Width 17.0” (43 cm)

Depth 18.3” (47 cm) Rated Airflow
Static

Pressure

Motor 0.33 HP

Power 4 amps Cord Length 25 ft. (7.6 m)

18.8” (48 cm)

1.36” (3.5 cm) Tested Airflow

Speeds Three

Switch Type

Overheating Cut­offs

Positions 3 (0°, 45°, 90°)

Rotary
2700 CFM

4587 CMH
1013 CFM

1718 CMH
Dual Thermal

Protectors

Weight

Carpet
Clamp

Circuit Pro­tection

Safety
Marks

Housing

27 lbs

Available as ac­cessory

Circuit Breaker/
GFCI

UL / cUL listed

Polyethylene

Troubleshooting

For any problems not listed below, call your local distributor or contact our Service Department toll free at 888-867-3235.

PROBLEM

Unit does not operate

Unit vibrates excessively

CAUSE

No power to machine Plug in the unit; check circuit breaker or fuse

Switch not turned on Turn on switch

Blower wheel jammed Remove material jamming wheel

Intake or exhaust blocked Turn machine off and allow to cool, then remove blockage

No power to outlet Reset circuit breaker/GFCI

GFCI tripped Reset circuit breaker/GFCI

Accumulation of soil on wheel Clean blower wheel

SOLUTION

07-01537C 2013-01 Warranty 07-00419 4 Dri-Eaz Products, Inc.

4