Dri-Eaz Sahara HD F352 Owner's Manual

Owner’s Manual Sahara HD

READ AND SAVE THESE INSTRUCTIONS

WARNING

This unit must be electrically
grounded

The power cord is equipped with a 3­prong grounding plug. Use only with
a matching receptacle.

Do not cut off the grounding prong.
Do not use an adapter.
Do not use with a damaged power

cord
Do not use an extension cord.
To reduce risk of fire or electric

shock, do not use this airmover with
any solid-state speed control device.

Read and understand manual
before operating.

DRI-EAZ PRODUCTS, INC.

15180 Josh Wilson Road, Burlington, WA USA 98233
Fax: [phone] Phone US: 800-932-3030

LegendBrandsRestoration.com

Model F352

Patents: hp://www.LBpatents.com

Use and Operation

Dri-Eaz TurboDryers are high-performance airmovers that promote the
evaporation of moisture from materials in order to speed the drying
process. They are durable and easy to operate, utilizing an effective
balance of static pressure and airflow.

DRYING SURFACES AND MATERIALS

Placement of TurboDryers

When drying the interior of a building, use at least one TurboDryer per water­damaged room, or one every 200 square feet. Try to get airflow to all wet sur­faces. Open interior doors to improve air circulation, and brace doors to pre­vent them from blowing shut.

WARNING

and unpredictable movement.
Do not allow children to play with or around TurboDryers. If they lift or get

a unit off balance, the powerful airflow can cause the TurboDryer to move
rapidly, risking injury.

Do not alter or modify your Dri-Eaz product in any way. Use only replace­ment parts authorized by Dri-Eaz Products, Inc. Modifications or use of
unapproved parts could create a hazard and will void your warran­ty. Contact your authorized Dri-Eaz distributor for assistance.

WARNING

b) Do not run cord under carpeting. Do not cover cord with throw rugs,
runners, or similar coverings. Do not route cord under furniture or appli­ances. Arrange cord away from traffic area and where it will not be tripped
over.

Do not move or carry a TurboDryer while under
operation. When the unit is in motion, the powerful
airflow is hard to control, and can produce rapid

a) Do not operate any fan with a damaged cord or
plug. Discard fan or return to an authorized service
facility for examination and/or repair.

Use a 115V, 3-prong
grounded connection

WARNING! Do not alter or modify your
Sahara in any way. Use only replace­ment parts authorized by Dri-Eaz
Products, Inc. Modifications or use of
unapproved parts could create a haz­ard and will void your warran­ty. Contact your authorized Dri-Eaz
distributor for assistance.

07-01534H F352 Dri-Eaz Products, Inc.

Do not use with
an adaptor

OPERATING YOUR TURBODRYER

 Locate the electrical cord and plug into a standard 3-prong outlet.
 Set the switch to the desired speed, based on amp draw as listed

by the switch on the side control panel.

READ AND SAVE THESE INSTRUCTIONS

WARNING

ELECTRIC SHOCK HAZARD

Keep motor and electrical parts
dry.

Do not operate in standing water.
Do not expose to rain, water or

snow.
Do not get the exterior, motor or wir-

ing wet.
Do not clean with wet objects, i.e.,

power washers, soap and water, etc.
If motor or electrical parts become

wet, allow them to dry completely
before using.

Read and understand manual be­fore operating.

WARNING

WARNING

Always disconnect the TurboDryer from its power
source before performing any maintenance or
cleaning.

Preventive Maintenance

Routine maintenance can significantly increase the life of your Tur­boDryer. It also promotes efficient operation. The applications and
amount of use by owners vary, so the recommendations listed below
are for average-to high-volume use in water damage. Constant opera­tion or use in other environments may require additional maintenance.
Contact Dri-Eaz for more information.

NOTE: Do not oil motor bearings; they are permanently oiled.

BEFORE EACH USE:

 Inspect power cord for cuts, fraying or damage; do not use if dam-

aged.

 Remove lint or obstructions from the grills using a vacuum or com-

pressed air.

 Inspect exterior components (switch, knob, etc.) for damage.

QUARTERLY (OR AS NEEDED):

 Clean the exterior with a household all-purpose spray cleaner.

Spray the rag, then apply to the surface.

 To renew shine on the plastic, use a vinyl cleaner.
 Remove grill and blower, then blow off internal components with

compressed air.

FIRE HAZARD
Keep air intakes clear. Reduced

airflow can cause motor to over­heat.

Clean any lint or other material
from the screens before each use.

Do not operate near draperies or
other material that could block the
air intakes.

Clean dust and dirt from motor
using a vacuum or compressed air.

Do not use or store where flamma­ble vapors like gasoline, solvents, or
thinners are present.

Do not use near open flames, or
heat sources.

Read and understand manual
before operating.

07-01534H F352 2 Dri-Eaz Products, Inc.

ANNUALLY:

 Inspect components and internal wiring for discoloration, loose con-

nections, or fraying.

OTHER USES FOR TURBODRYERS
Cool and Ventilate

Place the airmover on a flat surface, and direct the air from cooler are­as (including the outdoors) into a warm room.

STORAGE FOR TURBODRYERS

Stackable

Units can be stacked (up to 3) on their sides for stor­age. Stacking feature is not secure enough to be used
during transport.

Important Safety Instructions: Always disconnect the

TurboDryer from its power source before performing
any maintenance or cleaning.

TO CLEAN INTERIOR (AS NEEDED):

To remove grill and blower wheel:

1. Use a Phillips #2 screwdriver to remove 2 screws.

2. Remove inlet grill.

3. Loosen the blower wheel shaft nut (3/8” socket driver).

Note the backstop for ensuring alignment when replac­ing wheel.

4. Pull the blower wheel out of the unit.

1

4

5

6

2

3

To remove control panel and motor:

Rotate the unit onto its side so that the controls are facing up.

5. Unscrew 2 screws securing cord guard (#2 Phillips screwdriver).

6. Remove cord guard.

7. Remove 4 motor mount bolts with 3/8” nutdriver.

8. Pull motor assembly out of the housing.

7

3

8

To reassemble unit:

Follow the steps above in reverse order (starting with #8).

Note: Before tightening shaft nut on wheel, ensure that bolt is aligned with
flat spot on shaft (see photo A).

07-01534H F352 3 Dri-Eaz Products, Inc.

A

Specifications

Sahara HD

Height
Width

Depth
Static

Pres­sure

Motor

Power

18.8 in. (48 cm)

17.0 in. (43 cm)

18.3 in. (47 cm)

2.5 in. (6.4 cm )

1 HP

10 amps

Speeds
Switch Type

Rated Airflow

Tested Airflow

Overheating
Cutoffs

Cord Length

Three
Rotary
3500 CFM

5947 CMH
1560 CFM

2645 CMH

Dual Thermal
Protectors

25 ft. (7.6 m)

Weight
Positions
Carpet

Clamp
Circuit

Protec­tion

Safety
Marks

Housing

36 lbs. (26 kg)
3 (0°, 45°, 90°)
Available as

accessory

None

UL, C-UL

Polyethylene

WARNING: This product and other substances that may become airborne from its use contain
chemicals, including lead and phthalates, known to the State of California to cause cancer, birth defects,

or other reproductive harm. For more information, go to P65Warnings.ca.gov

Troubleshooting

For any problems not listed below, call your local distributor or contact our Service Department toll free at 800­932-3030.

PROBLEM

Unit does not operate

CAUSE

No power to machine Plug in the unit; check circuit breaker or fuse

Switch not turned on Turn on switch

SOLUTION

Unit vibrates excessively

Blower wheel jammed Remove material jamming wheel

Intake or exhaust blocked Turn machine off and allow to cool, then remove blockage

Accumulation of soil on wheel Clean blower wheel

07-01534H F352 4 Dri-Eaz Products, Inc.