Dri-Eaz F413-230V UK, F413-230V EU Owner's Manual

6

WARNING

Owner’s Manual

Revolution LGR Dehumidifier

Model F413-230V EU/UK

LEGEND BRANDS HOLDINGS LTD.

22 Plover Close, Interchange Park, Newport Pagnell, MK16 9PS

Tel: [phone] Fax: [phone] www.legendbrandseurope.com

The Dri-Eaz® Revolution LGR Dehumidifier reduces humidity in enclosed environments by removing wa­ter vapor from the air. The Revolution is ideal for water damage restoration, structural drying, construc­tion, and many other applications requiring temporary, high-performance dehumidification.

Patents: http://www.LBpatents.com

ORIGINAL INSTRUCTIONS

WARNING! Do not alter or modify your dehumidifier
in any way. Use only replacement parts authorized
by Dri-Eaz Products, Inc. Modifications or use of
unapproved parts could create a hazard and will
void your warranty. Contact your authorized
distributor for assistance.

WARNING! Electric shock hazard, rotating fan haz­ard and hot surface hazards.

• Inspect the power cord before use. If cord is dam­aged, do not use. Always grasp the plug (not the
cord) to unplug.

• Must be earthed. Insert three-prong plug on power
cord into a matching electrically earthed outlet. Do
not use adapter. Never cut off third prong. Do not
use an extension cord.

• The unit must be operated on a 230V/50 Hz circuit
protected by a Residual Current Device (RCD) de­vice.

• Keep motor and wiring dry.

• Always unplug unit before cleaning or servicing.

• Do not attempt to repair the unit. For service, contact

your local distributor.

FIRE HAZARD

• Keep away from open flames and heat sources.

• Do not use or store where vapors from gasoline, sol-

vents, thinners or other flammable materials may be
present.

BEFORE YOU BEGIN

Warranty registration

Warranty registration procedures vary by country/mar­ket. Contact your local distributor for assistance. Regis­tration allows us to better assist you with using, main­taining or servicing your equipment and to contact you in
case we have important safety information concerning
your Dri-Eaz product. If you determine service is re­quired, have your equipment model, serial number and
original proof of purchase available and ask for assis­tance with obtaining a return material authorization
(RMA).

GROUNDING INSTRUCTIONS

This unit’s plug must be inserted into an appropriate out­let that is properly installed and grounded in accordance
with all local codes and ordinances.

WARNING! Improper connection of the equipment­grounding conductor can result in a risk of electric
shock. Check with a qualified electrician or service
person if you are in doubt as to whether the outlets
are properly grounded. Do not modify the plugs pro­vided with the appliance – if the plugs do not fit the
outlets, have proper outlets installed by a qualified
electrician.

This equipment is for use on circuits with a nominal rat­ing of no more than 230V.

Handle the unit carefully

Always operate the unit on a stable, level surface. Do
not drop, throw, or place where it could fall. Rough treat­ment can damage the unit, and may create a hazardous
condition or void the warranty.

This unit intended for household and commercial use.

07-01899G F413-230V EU/UK 1 Legend Brands Holdings Ltd.

CONTROLS AND OPERATING
INSTRUCTIONS

Set unit upright

NOTICE: Always store, transport, and use the unit in
a horizontal position. If the unit is ever placed in a
vertical position, return it to the horizontal position
and let it stand for at least 30 minutes before turning
it on.

Positioning a Dehumidifier

For best results, operate your dehumidifiers in an en­closed area. Close all doors and windows that open to
the outside to maximize water removal efficiency. Place
your dehumidifier away from obstructions, and keep it
away from anything that could block airflow into and out
of the unit. For more information about creating an opti­mum drying environment, contact your local distributor.

Set up drain hose

This unit automatically pumps out water on a regular ba­sis. This dehumidifier is equipped with a quick-connect
fitting for quick attachment to the provided 12 m drain
hose. Unwrap the entire hose and place the open end in
a sink, drain, bucket or outdoors – anywhere that water
can drain out safely. If you use a bucket or other con­tainer for water collection, check it regularly to prevent
overflows.

NOTICE: Uncoil and straighten the entire drain hose. Do
not leave any part of the hose coiled and do not place
the end of the hose higher than 6 m above the bottom of
the unit. Also check for kinks or other obstructions that
might restrict the flow of water. Obstructions may cause
a water backup and result in overflows.

Fig. A: Parts Identification

Carry handles

Control
panel

Air inlet

Cord and
hose storage
wraps.

Condensate
drain quick­connect

UNIT ON XXXX HRS

INLET XXX°C / INLET 00%

The first line of the display shows the total number of
hours the unit has been in operation. This value may be
reset to zero to track job hours (see “Job Hours Reset”
below). The second line of the display alternates be­tween inlet temperature and inlet humidity.

Air outlet

Temp/RH
sensor

Remove/Insert
air filter here.

Plug in electrical cord

The unit should be plugged into a 230V/50Hz outlet.

Startup display and normal display modes

When unit is first plugged in to AC power, the control
panel display will briefly cycle through a series of
readouts. This is part of the unit’s self-diagnosis proce­dure and no user intervention is required.

Turn the unit on

The control panel has a display and a touchpad with four
keys. Press the
will now go through a compressor delay countdown (up
to sixty seconds in duration) and a self diagnostics pro­cess.

Once the compressor delay countdown and self-diag­nostics are complete, the display will switch to normal
display mode.

07-01899G F413-230V EU/UK 2 Legend Brands Holdings Ltd.

ON/OFF to turn the unit on. The unit

User Settings Menu

ON/OFF

Press and release to turn unit

or off.

DISPLAY MENU

Press to select next item in

display.

MENU SELECTION /
UP KEY

Press to toggle or select values
in menu displayed.

PURGE PUMP

Press and release to start purge.

A number of display settings may be changed by the
user. System information can also be displayed. These
items are accessed by pressing

DISPLAY MENU.
Each press of the key will display the next parameter.
When you reach the parameter you wish to adjust, press

MENU SELECTION to increase the value. Press
DISPLAY MENU again to accept the setting and re-start
the display cycle.

Note that only menu items followed by a greater-than
symbol ( > ) may be adjusted.

All settings and modes are discussed in detail in Control
Panel Guide.

CONTROL PANEL

DISPLAY

ON/OFF

DISPLAY
MENU

on

menu. Menu item will show in

Display will count down sec­onds remaining until purge is
complete.

PURGE PUMP

MENU
SELECTION /
UP KEY

Error messages

If the onboard diagnostics discover a problem, the unit
will display an error message. See “Error Messages,”
below, for an explanation of each message.

Control Panel Guide

ON/OFF. Press to turn the unit on or off. When the ma-

chine is turned on, the display normally reads PLEASE
WAIT COMP. DELAY and performs a numeral count­down for a maximum of 60 seconds to 0. This delay al­lows time for refrigerant pressures to equalize for easier
starting. Once the unit completes the compressor delay,
the display shows UNIT ON XX HRS and cycles be­tween INLET XX°F and INLET XX%. NOTE: If no com­pressor delay countdown is displayed, a delay is not
necessary and the machine will begin operation immedi­ately.

DISPLAY MENU. Press to cycle through the display of
additional dehumidifier conditions and User Settings. To
return to the main menu, press the ON/OFF key once.

MENU SELECTION. Press to change the values of the
"User Defined" settings. The MENU SELECTION key
acts as the UP key for adjusting the setpoint for Humidi­stat mode operation. See User Settings Menu (below)
for details.

PURGE. Press to empty water from the condensate
pump reservoir. The display will read PUMP PURGING
with a numeral countdown.
NOTE: During normal operation, the pump purges auto­matically.

Changing settings and viewing system information

Display setting changes and system information can be
accessed by pressing
of the key will display the next parameter (see list be­low). When you reach the parameter you wish to adjust,
press
Press

MENU SELECTION to increase the value.

DISPLAY MENU again to accept the setting

and re-start the display cycle

Note that only menu items followed by a greater-than
symbol ( > ) may be adjusted.

DISPLAY MENU. Each press

07-01899G F413-230V EU/UK 3 Legend Brands Holdings Ltd.