Dream Vision R699740, Dream Bee R699740 User Manual

2 R699740 - DreamBee User Manual

Changes

DreamVision provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not
limited to the implied warranties or merchantability and fitness for a particular purpose. DreamVision may make
improvements and/or changes to the product(s) and/or the program(s) described in this publication at any time
without notice.
This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the
information in this publication; these changes are incorporated in new editions of this publication.

Copyright

All right reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be
recorded, transmitted or stored in a retrieval system without the prior written consent of DreamVision.

Guarantee

DreamVision provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of
guarantee. On receipt, the purchaser must immediately inspect all delivered goods for damage incurred during
transport, as well as for material and manufacturing faults. DreamVision must be informed immediately in writing of
any complaints.
If the purchaser or third party caries out modifications or repairs on goods delivered by DreamVision, or if the goods
are handle incorrectly, in particular if the systems are commissioned operated incorrectly or if, after the transfer of
risks, the goods are subject to influences not agreed upon in the contract, all guarantee claims of the purchaser will
be rendered invalid. Not included in the guarantee coverage are system failures which are attributed to programs or
special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as well as normal maintenance
are not subject to the guarantee provided by DreamVision either.
The environmental conditions as well as the servicing and maintenance regulations specified in this manual must
be complied with by the customer.

Trademarks

Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of
their respective holders. All brands and product names mentioned in this manual serve as comments or examples
and are not to be understood as advertising for the products of their manufactures.

R699740 - DreamBee User Manual 3

TABLE OF CONTENTS

1.0 PACKAGING AND DIMENSIONS ............................................................................... 6

1.1 Box content........................................................................................................................................ 6

1.2 Projector Packaging ........................................................................................................................... 6

Way of Packaging................................................................................................................6

To unpack ............................................................................................................................ 6

1.3 Projector Dimensions......................................................................................................................... 6

2.0 SAFETY INSTRUCTIONS ............................................................................................. 7

2.1 Important information........................................................................................................................ 7

Lead-free regulation ............................................................................................................7

Information for Users on Disposal of Old Equipment ........................................................ 7

About burning-in of the D-ILA device................................................................................ 7

About the installation place................................................................................................. 7

2.2 Important safeguards.......................................................................................................................... 7

2.3 REGIONAL SPECIFIC INFORMATION......................................................................................... 9

FCC INFORMATION (USA ONLY) ................................................................................. 9

3.0 INSTALLATION GUIDELINES .................................................................................. 10

3.1 Viewing Conditions ......................................................................................................................... 10

3.2 Environment of Use......................................................................................................................... 10

Mounting this unit to the ceiling ....................................................................................... 10

Installation Environment................................................................................................... 10

Precautions of Usage......................................................................................................... 10

3.3 Air-Flow and Space Requirements.................................................................................................. 11

3.4 Ceiling mounting the unit ................................................................................................................ 12

Precautions for Ceiling-mount .......................................................................................... 12

3.5 Projection Distance and Offset Setting............................................................................................ 12

Projection Distance ........................................................................................................... 12

Vertical and Horizontal Offset Setting .............................................................................. 13

4.0 REMOTE CONTROL UNIT (RCU) ............................................................................ 16

4.1 General view.................................................................................................................................... 16

4.2 Loading and replacing batteries....................................................................................................... 16

4.3 How to use the remote control unit.................................................................................................. 17

5.0 GETTING STARTED .................................................................................................... 18

5.1 General View ................................................................................................................................... 18

Front side........................................................................................................................... 18

Rear side............................................................................................................................ 18

5.2 Connecting the Power Cord............................................................................................................. 18

5.3 Focus and Zoom Adjust ................................................................................................................... 19

5.4 Operating LEDs ............................................................................................................................... 20

5.5 Operating and Navigation Buttons .................................................................................................. 21

6.0 CONNECTIONS............................................................................................................. 22

6.1 The DreamBee PRO Version ........................................................................................................... 22

6.2 Connecting a device with Digital Output ........................................................................................ 22

Connecting a device with DVI-D Output.......................................................................... 22

Connecting to a device with HDMI Output ...................................................................... 22

6.3 Connecting a device with S-Video Output....................................................................................... 23

6.4 Connecting a device with Video Output .......................................................................................... 23

6.5 Connecting a device with Component Output................................................................................. 23

6.6 Connecting a device with SCART Output (European market)........................................................ 24

6.7 Automation and control port: RS-232 Input....................................................................................24

7.0 MENU AND PICTURE SETTING............................................................................... 25

7.1 How to start up the Menu ................................................................................................................ 25

Box like Menu Structure ................................................................................................... 25

How to activate the Menu Structure.................................................................................. 25

How to select an Item and make an Adjustment............................................................... 25

4 R699740 - DreamBee User Manual

7.2 Menu Structure ................................................................................................................................ 26

7.3 Image Menu ..................................................................................................................................... 28

Contrast ............................................................................................................................. 28

Brightness.......................................................................................................................... 28

Color.................................................................................................................................. 28

Tint .................................................................................................................................... 28

Sharpness........................................................................................................................... 28

DNR .................................................................................................................................. 28

Color Temp........................................................................................................................ 28

Gamma .............................................................................................................................. 29

Offset................................................................................................................................. 29

Pixel Adjust ....................................................................................................................... 29

7.4 Setup Menu...................................................................................................................................... 29

Image Profile..................................................................................................................... 29

Profile Memory ................................................................................................................. 29

Picture Position ................................................................................................................. 29

Picture Shift setting ...........................................................................................................29

HDMI Input Level............................................................................................................. 29

Mask.................................................................................................................................. 30

7.5 Custom Image Profile ...................................................................................................................... 30

Parameters stored into an Image Profile ........................................................................... 30

Setting a new Image Profile .............................................................................................. 30

7.6 Video Menu...................................................................................................................................... 30

COMP ............................................................................................................................... 30

HDMI Color Space ........................................................................................................... 31

Aspect................................................................................................................................ 31

Film Mode......................................................................................................................... 31

Color System..................................................................................................................... 31

Black Level ....................................................................................................................... 31

7.7 Install Menu ..................................................................................................................................... 31

Menu Position ...................................................................................................................31

Menu Display ....................................................................................................................31

Line Display ...................................................................................................................... 31

Flip H. ............................................................................................................................... 31

Flip V. ................................................................................................................................ 31

High Altitude..................................................................................................................... 31

7.8 Function Menu................................................................................................................................. 32

Back Color ........................................................................................................................ 32

Sleep Timer ....................................................................................................................... 32

D-ILA Logo....................................................................................................................... 32

Lamp Power ......................................................................................................................32

Test Pattern........................................................................................................................ 32

Language ........................................................................................................................... 32

7.9 Information Menu............................................................................................................................ 32

Input .................................................................................................................................. 32

Source................................................................................................................................ 32

Lamp Time ........................................................................................................................ 32

8.0 MAINTENANCE............................................................................................................ 33

8.1 Clean Dirt on the Cabinet ................................................................................................................ 33

Caution .............................................................................................................................. 33

8.2 Dirt on the Lens ............................................................................................................................... 33

8.3 Replacing the Lamp......................................................................................................................... 33

Light-source Lamp and Lamp Usage Time....................................................................... 33

Procedure for Lamp Replacement..................................................................................... 34

Resetting Lamp Time........................................................................................................ 34

8.4 Cleaning and Replacing the Dust Filter........................................................................................... 34

Pull out the plug from the power outlet ............................................................................ 34

Remove the inner filter...................................................................................................... 34

Clean the filter................................................................................................................... 35

R699740 - DreamBee User Manual 5

Reinstall the inner filter..................................................................................................... 35

8.5 Troubleshooting............................................................................................................................... 35

On Screen Warnings.......................................................................................................... 35

LED Warning .................................................................................................................... 36

Before sending the projector to repair............................................................................... 37

9.0 MISCELLANEOUS ....................................................................................................... 38

9.1 RS-232C input ................................................................................................................................. 38

Pin Assignment..................................................................................................................38

External Control ................................................................................................................38

Communication Specifications ......................................................................................... 38

Command Format.............................................................................................................. 38

Response data format ........................................................................................................ 38

Available Commands and Parameters............................................................................... 39

9.2 Specifications.................................................................................................................................. 41

Overview ........................................................................................................................... 41

Dimensions........................................................................................................................ 42

1.0 PACKAGING AND DIMENSIONS

6 R699740 - DreamBee User Manual

1.0 PACKAGING AND DIMENSIONS

1.1 Box content

The following accessories are packed together with this unit. Please confirm all items.
If any item is missing, please contact your dealer.

•1 DreamVision Full HD projector, model DreamBee (R9010086)

•1 User Manual (R699740)

•1 Remote control unit RCU

•1 Power Cord

•2 AAA size batteries

1.2 Projector Packaging

Way of Packaging

The projector is packed in a carton box. To provide protection during transportation, the projector is surrounded with
foam. The package is secured with banding and fastening clips.

To unpack

a) Pull off the adhesive tape or cut the adhesive tape but take care not to insert the knife too deep otherwise the
projector can be damaged.

b) Take the projector out of its shipping carton, remove the foam rubber and place it on a table.

1.3 Projector Dimensions

585 mm

23.0’’

470 mm

18.5’’

585 mm

23.0’’

205 mm 8.0’’

470 mm

18.5’’

2.0 SAFETY INSTRUCTIONS

R699740 - DreamBee User Manual 7

2.0 SAFETY INSTRUCTIONS

2.1 Important information

Lead-free regulation

This product has a High Intensity Discharge (HID) lamp that contains a small amount of mercury. It also contains
lead in some components.
Disposal of these materials may be regulated in your community due to environmental considerations. For disposal
or recycling information please contact your local authorities, or the Electronics Industries Alliance: http://
www.eiae.org.

Information for Users on Disposal of Old Equipment

This symbol indicates that the electrical and electronic equipment should not be disposed as general
household waste at its end of life. Instead, the product should be handed over to the applicable
collection point for the recycling of electrical and electronic equipment for proper treatment, recovery
and recycling in accordance with your national legislation.
By disposing of this product correctly, you will help to conserve natural resources and will help
prevent potential negative effects on the environment and human health which could otherwise be caused by
inappropriate waste handling of this product.
For more information about collection point and recycling of this product, please contact your local municipal office,
your household waste disposal service or the shop where you purchased the product. Penalties may be applicable
for incorrect disposal of this waste, in accordance with national legislation.

Other Countries outside the European Union:

If you wish to dispose of this product, please do so in accordance with applicable national legislation or other rules
in your country for the treatment of old electrical and electronic equipment.

About burning-in of the D-ILA device

Do not allow the same still picture to be projected for a long time or an abnormally bright video picture to be
projected. Do not project video images with high-intensity or high contrast on a screen. The video image could be
burnt into the D-ILA device.
Use special care when projecting video games or computer program images. There is no problem with ordinary
video-cassette playback images.

About the installation place

Do not install the projector in a place that cannot support its weight securely.
If the installation place is not sturdy enough, the projector could fall or overturn, possibly causing personal injury.

2.2 Important safeguards

Electrical energy can perform many useful functions. This unit has been engineered and manufactured to assure
your personal safety. But IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE
HAZARD. In order not to defeat the safeguards incorporated into this product, observe the following basic rules for

its installation, use and service.

Please read these Important Safeguards carefully before use.

• All the safety and operating instructions should be read before the product is operated.

CAUTION:

To reduce the risk of electric shock, do not remove cover. Refer servicing to qualified service personnel. This
projector is equipped with a 3-blade grounding type plug to satisfy FCC rule. If you are unable to insert the plug
into the outlet, contact your electrician.

WARNING:

To prevent fire or shock hazards, do not expose this appliance to rain or moisture. This apparatus must be
earthed.

The power input is auto-ranging from 100 to 240 VAC.

2.0 SAFETY INSTRUCTIONS

8 R699740 - DreamBee User Manual

• All warnings on the product and in the operating
instructions should be adhered to.

• All operating instructions should be followed.

• Place the projector near a wall outlet where the
plug can be easily unplugged.

• Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.

• Do not use attachments not recommended by the
product manufacturer as they may be hazardous.

• Do not use this product near water. Do not use
immediately after moving from a low temperature
to high temperature, as this causes
condensation, which may result in fire, electric
shock, or other hazards.

• Do not place this product on an unstable cart,
stand, or table. The product may fall, causing
serious injury to a child or adult, and serious
damage to the product. The product should be
mounted according to the manufacturer’s
instructions, and should use a mount
recommended by the manufacturer.

• When the product is used on a cart, care should
be taken to avoid quick stops, excessive force,
and uneven surfaces which may cause the
product and cart to overturn, damaging
equipment or causing possible injury to the
operator.

• Slots and openings in the cabinet are provided
for ventilation. These ensure reliable operation of
the product and protect it from overheating.
These openings must not be blocked or covered.
(The openings should never be blocked by
placing the product on bed, sofa, rug, or similar
surface. It should not be placed in a built-in
installation such as a bookcase or rack unless
proper ventilation is provided and the
manufacturer’s instructions have been adhered
to). For proper ventilation, separate the product
from other equipment, which may prevent
ventilation and keep a distance of more than 5-9“
(150 mm).

• This product should be operated only with the
type of power source indicated on the label. If you
are not sure of the type of power supply to your
home, consult your product dealer or local power
company.

• This product is equipped with a three-wire plug.
This plug will fit only into a grounded power
outlet. If you are unable to insert the plug into the
outlet, contact your electrician to install the
proper outlet. Do not defeat the safety purpose of
the grounded plug.

•Power-supply cords should be routed so that they
are not likely to be walked on or pinched by items
placed upon or against them. Pay particular
attention to cords at doors, plugs, receptacles,
and the point where they exit from the product.

•For added protection of this product during a
lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the

wall outlet and disconnect the cable system. This
will prevent damage to the product due to
lightning and power line surges.

• Do not overload wall outlets, extension cords, or
convenience receptacles on other equipment as
this can result in a risk of fire or electric shock.

•Never push objects of any kind into this product
through openings as they may touch dangerous
voltage points or short out parts that could result
in a fire or electric shock. Never spill liquid of any
kind on the product.

• Do not attempt to service this product yourself as
opening or removing covers may expose you to
dangerous voltages and other hazards. Refer all
service to qualified service personnel.

• Unplug this product from the wall outlet and refer
service to qualified service personnel under the
following conditions:

a) When the power supply cord or plug is
damaged.

b) If liquid has been spilled, or objects have fallen
on the product.

c) If the product has been exposed to rain or
water.

d) If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the Operation
Manual, as an improper adjustment of controls may
result in damage and will often require extensive
work by a qualified technician to restore the product
to normal operation.

e) If the product has been dropped or damaged in
any way.

f) When the product exhibits a distinct change in
performance - this indicates a need for service.

• When replacement parts are required, be sure
the service technician has used replacement
parts specified by the manufacturer or with same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or
other hazards.

• Upon completion of any service or repairs to this
product, ask the service technician to perform
safety checks to determine that the product is in
proper operating condition.

• The product should be placed more than one foot
away from heat sources such as radiators, heat
registers, stoves, and other products (including
amplifiers) that produce heat.

• When connecting other products such as VCR’s,
and personal computers, you should turn off the
power of this product for protection against
electric shock.

• Do not place combustible behind the cooling fan.
For example, cloth, paper, matches, aerosol cans
or gas lighters that present special hazards when
over heated.

• Do not look into the projection lens while the
illumination lamp is turned on. Exposure of your
eyes to the strong light can result in impaired

2.0 SAFETY INSTRUCTIONS

R699740 - DreamBee User Manual 9

eyesight.

• Do not look into the inside of this unit through vents (ventilation holes), etc. Do not look at the illumination lamp
directly by opening the cabinet while the illumination lamp is turned on. The illumination lamp also contains
ultraviolet rays and the light is so powerful that your eyesight can be impaired.

• Do not drop, hit, or damage the light-source lamp (lamp unit) in any way. It may cause the light-source lamp to
break and lead to injuries. Do not use a damaged light source lamp. If the light-source lamp is broken, ask your
dealer to repair it. Fragments from a broken light-source lamp may cause injuries.

• The light-source lamp used in this projector is a high pressure mercury lamp. Be careful when disposing of the
light source lamp. If anything is unclear, please consult your dealer.

• Do not ceiling-mount the projector to a place which tends to vibrate; otherwise, the attaching fixture of the
projector could be broken by the vibration, possibly causing it to fall or overturn, which could lead to personal
injury.

• Use only the accessory cord designed for this product to prevent shock.

• The power supply voltage rating of this product is AC120 V, AC100 V – AC240 V, the power cord attached
conforms to the following power supply voltage. Use only the power cord designated by our dealer to ensure
Safety and EMC.

• When it is used by other power supply voltage, power cable must be changed.

• Ensure that the power cable used for the projector is the correct type for the AC outlet in your country. Consult
your product dealer.

• Caution: Do not allow any unqualified person to install the unit. Be sure to ask your dealer to install the unit (e.g.
attaching it to the ceiling) since special technical knowledge and skills are required for installation. If installation
is performed by an unqualified person, it may cause personal injury or electrical shock.

2.3 REGIONAL SPECIFIC INFORMATION

FCC INFORMATION (USA ONLY)

Changes or modification not approved by DreamVision could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encourage to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC

The Federal Communications Commission (FCC) is an independent United States government agency, created,
directed, and empowered by Congressional statute.
The FCC was established by the Communications Act of 1934 as the successor to the Federal Radio Commission
and is charged with regulating all non-Federal Government use of the radio spectrum, including radio and television
broadcasting, and all interstate telecommunications like wire, satellite and cable as well as all international
communications that originate or terminate in the United States. The FCC's jurisdiction covers the 50 states, the
District of Columbia, and U.S. possessions.

3.0 INSTALLATION GUIDELINES

10 R699740 - DreamBee User Manual

3.0 INSTALLATION GUIDELINES

3.1 Viewing Conditions

Brightness of the room

Avoid direct exposure of screen to direct sunlight and illumination. Block light using a curtain. Images can be well
projected by darkening the brightness of the room.

Do not view screen for prolonged hours.

Looking at the screen continually for a prolonged time will cause your eyes to get tired. Allow your eyes to rest at
intervals.

Do not use this unit when image flickers

This may cause your eyesight to deteriorate.

3.2 Environment of Use

• Do not use this unit in rooms with cigarette smoke or oily smoke. This may cause the unit to malfunction.

Mounting this unit to the ceiling

Check temperature around the unit. When a heater is in use, the ceiling may reach a temperature higher than
anticipated, hence leading to malfunction of the unit.

Installation Environment

This unit is a precision device. Do not install it at the following places. Doing so may cause fire or malfunction of the
unit.

• Where there is water, humidity or dust.

• Where the unit may be subjected to oily or cigarette smoke.

• On a soft surface such as carpet or cushion.

• Where the unit may be subjected to high temperature due to direct sunlight.

• When temperature is high or low.

Operation temperature range: +5°C to +35°C.
Storage temperature range: -10°C to +60°C.
Relative humidity range 20% to 80% (without condensation).

Precautions of Usage

This unit makes use of a light source lamp that may reach a high temperature during projection. Do not allow
projection under the following conditions. Doing so may cause fire or malfunction of the unit.

• Projection with the unit laid on sides.

• Projection with the unit installed in an unreasonable angle. Avoid using this unit at an angle of more than 5°
horizontally and 25° vertically. Doing so may cause unevenness in the color or shorten the lamp life.

• Projection at a location that blocks the air inlets or exhaust vents.

• Projection at a place exposed to air blasts from an air conditioner.

3.0 INSTALLATION GUIDELINES

R699740 - DreamBee User Manual 11

3.3 Air-Flow and Space Requirements

This unit can be installed in table position. Make sure that the unit is installed within the space requirements
described below.

•A: Air inlets

•B: Air outlets

Air flow

Space requirements

A

A

AB

B

A

AB

100 mm

150 mm

150 mm

100 mm

150 mm

150 mm

3.0 INSTALLATION GUIDELINES

12 R699740 - DreamBee User Manual

3.4 Ceiling mounting the unit

When mounting of this unit is required, do so by removing the 4 feet and make use of the 4 screw holes (M5
screws) at the bottom of this unit. Allow sufficient space around the air inlets to avoid blocking them

.

Precautions for Ceiling-mount

•To ceiling-mount this unit, special expertise and techniques are necessary.
Be sure to ask your dealer or specialist to perform mounting.

• Do not mount at places that may be subjected to vibration and shock.

• Depth of the screw holes (screw length) is 30 mm. Use screws shorter than
30 mm but longer than 19 mm.

• Install at a safe place in case this unit or a part of it may drop. If the light­source lamp is broken, small pieces of glass from the mesh of the filter may
appear outside the unit.

• Regardless whether the unit is still under guarantee, DreamVision is not
liable for any product damage caused by mounting the unit with third party
ceilling mount or when the environment is not suitable for ceiling-mount.

3.5 Projection Distance and Offset Setting

Projection Distance

• The projection screen sizes and projecting distances in the table above are provided only as a guide. Please use
them as reference during installation.

• Use a projection image of 16:9 aspect ratio for setup adjustment.

Projection Screen Size

Diagonal size

(Aspect Ratio 16:9)

Projection Screen Size

Base size

(Aspect Ratio 16:9)

Projection Screen

Height

(Aspect Ratio 16:9)

DreamBee

Projecting Distance

minimum - maximum

50" (1270 mm) 43,6" (1107 mm) 24,5" (623 mm) 1518 mm - 3050 mm

60" (1524 mm) 52,3" (1328 mm) 29,4" (747 mm) 1821 mm - 3659 mm

70" (1778 mm) 61,0" (1550 mm) 34,3" (872 mm) 2125 mm - 4269 mm

83" (2108 mm) 72,3" (1837 mm) 40,7" (1034 mm) 2519 mm - 5062 mm

92" (2337 mm) 80,2" (2037 mm) 45,1" (1146 mm) 2792 mm - 5611 mm

100" (2540 mm) 87,2" (2214 mm) 49,0" (1245 mm) 3035 mm - 6099 mm

110" (2794 mm) 95,9" (2435 mm) 53,9" (1370 mm) 3339 mm - 6709 mm

138" (3505 mm) 120,3" (3055 mm) 67,7" (1718 mm) 4188 mm - 8417 mm

150" (3810 mm) 130,7" (3321 mm) 73,5" (1868 mm) 4553 mm - 9149 mm

180" (4572 mm) 156,9" (3985 mm) 88,2" (2241 mm) 5463 mm - 10978 mm

200" (5080 mm) 174,3" (4428 mm) 98,1" (2491 mm) 6070 mm -12198 mm

250" (6350 mm) 218" (5535 mm) 122,6" (3113 mm) 7588 mm - 15248 mm

3.0 INSTALLATION GUIDELINES

R699740 - DreamBee User Manual 13

Ver tical and Horizontal Offset Setting

The optimum image can be obtained when the centre of this projector’s lens and the screen are placed
perpendicular to each other. Take note of the projection angle when placing them. Failing to do so may give rise to

trapezoidal distortion of the projected image.

This unit comes with a optical shift that features vertical and horizontal adjustment of the projection screen position.
Adjust the picture to your screen.

• The vertical shift level is between -80% and 80% of the screen height.

• The horizontal shift level is between -34% and 34% of screen base.

• The shift level is set to 0% vertically and horizontally by default.

• The position of the projection screen may be out of alignment due to the gear movement.

This unit comes with a vertical and horizontal shift to suit most installations. Make sure that your installation
does not exceed 80% vertical offset and 34% horizontal offset.

3.0 INSTALLATION GUIDELINES

14 R699740 - DreamBee User Manual

3.5.0.1 Adjust the picture position vertically

The DreamBee projector has two dials to center the picture to the screen vertically and horizontally. Refer to the
picture below to locate the dials.

The Vertical and Horizontal shift dials are located at the bottom of the unit.

Turn clockwise to shift the picture on the screen downward.

Turn anti-clockwise to shift the picture on the screen upward.

Ver tical Shift Dial
(-80% to +80%)

Horizontal Shift Dial
(-34% to +34%)