Page 1
The retina projectors
V 1.2
Page 2
Changes
Dreamvision provides this manual ‘as is’ without warranty of any kind, either expressed or implied, including but
not limited to the implied warranties or merchantability and tness for a particular purpose. Dreamvision may
make improvements and/or changes to the product(s) and/or the program(s) described in this publication at any
time without notice.
This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to
the information in this publication; these changes are incorporated in new editions of this publication.
Copyright
All right reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be
recorded, transmitted or stored in a retrieval system without the prior written consent of Dreamvision.
Guarantee
Dreamvision provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of
guarantee. On receipt, the purchaser must immediately inspect all delivered goods for damage incurred during
transport, as well as for material and manufacturing faults. Dreamvision must be informed immediately in writing
of any complaints. If the purchaser or third party caries out modications or repairs on goods delivered by
Dreamvision, or if the goods are handle incorrectly, in particular if the systems are commissioned operated
incorrectly or if, after the transfer of risks, the goods are subject to inuences not agreed upon in the contract, all
guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage are system
failures which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces.
Normal wear as well as normal maintenance are not subject to the guarantee provided by Dreamvision either.
The environmental conditions as well as the servicing and maintenance regulations specied in this manual must
be complied with by the customer.
Trademarks
Brands and product names mentioned in this manual may be trademarks, registered trademarks or copyrights
of their respective holders. All brands and product names mentioned in this manual serve as comments or
examples and are not to be understood as advertising for the products of their manufactures.
Page 3
TABLE OF CONTENTS
1.0 SAFETYINSTRUCTIONS ..................................................................................................5
1.1 Important Information ....................................................................................................................5
1.2 Regional Specic Information........................................................................................................5
1.3 Important Safeguards .....................................................................................................................5
1.4 Image projector classication .........................................................................................................7
2.0 INSTALLATIONGUIDELINES .......................................................................................7
2.1 Introduction ....................................................................................................................................7
2.2 THX 4K Display Certication (Eos Signature only) ...................................................................8
2.3 Environment of Use........................................................................................................................8
2.4 Air-Flow and Space Requirements .................................................................................................8
2.5 Installing the projection screen.......................................................................................................9
2.6 When to use the High Altitude mode .............................................................................................9
2.7 Ceiling Mounting the Unit .............................................................................................................9
2.8 Projection Distance.......................................................................................................................10
2.9 Setting the Lens and using Lens Memories..................................................................................10
3.0 REMOTECONTROLUNIT(RCU) .............................................................................. 12
4.0 GETTINGSTARTED ......................................................................................................... 13
4.1 General View ................................................................................................................................13
4.2 Connecting the Power Cord .........................................................................................................13
4.3 Operating and Navigation Buttons ...............................................................................................14
5.0 CONNECTIONS ................................................................................................................... 14
5.1 Caution when connecting a Device to HDMI Input .....................................................................14
5.2 Connecting a Video Source to the Projector.................................................................................15
5.3 Connecting an Automation or Control device ..............................................................................15
6.0 FIRSTSTARTUP ................................................................................................................ 16
6.1 Turn the power ON .......................................................................................................................16
6.2 Turn the Power O .......................................................................................................................16
7.0 MENUSTRUCTURE .......................................................................................................... 17
8.0 PICTUREADJUST ............................................................................................................. 20
8.1 Picture Modes and Color Proles .................................................................................................20
8.2 Advanced Picture Mode ...............................................................................................................20
8.3 Advanced Color Prole ................................................................................................................21
8.4 Color Temperature ........................................................................................................................21
8.5 Advanced Color Temperature .......................................................................................................22
8.6 Gamma .........................................................................................................................................22
8.7 Advanced Gamma ........................................................................................................................22
8.8 Multiple Pixel Control Level (MPC Level) .................................................................................23
8.9 Motion Control .............................................................................................................................23
8.10 Contrast ........................................................................................................................................23
8.11 Brightness .....................................................................................................................................23
8.12 Color .............................................................................................................................................24
8.13 Tint ...............................................................................................................................................24
9.0 4KINPUTS ............................................................................................................................. 24
9.1 Choosing the correct Input level ..................................................................................................24
9.2 High Dynamic Range sources ......................................................................................................24
9.3 4K contents and their Color Proles ............................................................................................25
10.0 INPUTSIGNAL .................................................................................................................... 26
10.1 Input Level ...................................................................................................................................26
10.2 Color Space ..................................................................................................................................26
10.3 HDR Setting .................................................................................................................................26
10.4 HDMI2 EDID ...............................................................................................................................26
11.0 3DCONTENTAND3DPROJECTION ....................................................................... 27
R699900 - Eos Series User Manual 3
Page 4
11.1 General Information about 3D playback ......................................................................................27
11.2 3D Settings ...................................................................................................................................27
11.3 Operating the 3D Glasses .............................................................................................................28
12.0 INSTALLATION .................................................................................................................. 29
12.1 Installation Modes ........................................................................................................................29
12.2 Lens Control .................................................................................................................................29
12.3 Pixel Adjust ..................................................................................................................................29
12.4 Mask .............................................................................................................................................30
12.5 Anamorphic ..................................................................................................................................30
12.6 Screen Adjust and Screen No. ......................................................................................................31
12.7 Installation Style ...........................................................................................................................31
12.8 Keystone .......................................................................................................................................31
12.9 Pincushion ....................................................................................................................................31
12.10 Aspect ...........................................................................................................................................31
13.0 DISPLAYSETUP ................................................................................................................. 32
14.0 FUNCTION ............................................................................................................................ 32
14.1 Trigger ..........................................................................................................................................32
14.2 O-Timer ......................................................................................................................................32
14.3 ECO Mode ....................................................................................................................................32
14.4 Network ........................................................................................................................................32
14.5 Remote Code A or B ..................................................................................................................... 32
14.6 High Altitude Mode ...................................................................................................................... 33
14.7 Lamp Reset ...................................................................................................................................33
14.8 Factory Reset ................................................................................................................................33
14.9 Software Update ...........................................................................................................................33
15.0 INFORMATIONMENU .................................................................................................... 33
16.0 CINEMASCOPESETUPS ................................................................................................ 34
16.1 Cinemascope setup with Lens Zoom............................................................................................34
16.2 Installing a 2.35:1 screen with the Static Cinemascope kit ..........................................................34
17.0 MAINTENANCE .................................................................................................................. 35
17.1 Cleaning and Replacing the Dust Filter .......................................................................................35
17.2 Dirt on the Lens ............................................................................................................................36
17.3 Replacing the Lamp......................................................................................................................36
17.4 Blinking LEDs and Troubleshooting ............................................................................................38
18.0 MISCELLANEOUS ............................................................................................................. 39
18.1 RS-232C protocol .........................................................................................................................39
18.2 LAN protocol ...............................................................................................................................41
18.3 Infra Red, long hex-pronto compatible RCU ...............................................................................42
18.4 Specications................................................................................................................................43
18.5 Dimensions ...................................................................................................................................44
4
R699900 - Eos Series User Manual
Page 5
SAFETY INSTRUCTIONS
1.0 SAFETY INSTRUCTIONS
1.1 Important Information
Lead-free regulation
This product has a High Intensity Discharge (HID) lamp that contains a small amount of mercury. It also contains
lead in some components. Disposal of these materials may be regulated in your community due to environmental
considerations. For disposal or recycling information please contact your local authorities, or the Electronics
Industries Alliance: http://www.eiae.org. Call 1-800-252-5722(For USA) or 1-800-964-2650(For Canada)
Information for Users on Disposal of Old Equipment
This symbol indicates that the electrical and electronic equipment should not be disposed as general
household waste at its end of life. Instead, the product should be handed over to the applicable
collection point for the recycling of electrical and electronic equipment for proper treatment, recovery
and recycling in accordance with your national legislation.
For more information about collection point and recycling of this product, please contact your local
municipal ofce, your household waste disposal service or the shop where you purchased the product. Penalties
may be applicable for incorrect disposal of this waste, in accordance with national legislation.
1.2 RegionalSpecicInformation
CE mark and Directive 2011/65/EU - ROHS 2 (Europe only) In accordance with Article 7 and the
adoption into national law by 2nd January 2013, this product has been designed and manufactured in accordance
with Article 4. The technical documentation and the written declaration of conformity that assesses the product
conformity can be provided to the competent National Authority upon an email request to: rohs2@dreamvision.net
Other Countries outside the European Union:
If you wish to dispose of this product, please do so in accordance with applicable national legislation or other rules
in your country for the treatment of old electrical and electronic equipment.
FCC Information (USA only)
Changes or modication not approved by Dreamvision could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
CAN ICES-3 (A) / NMB-3 (A)
To reduce the risk of electric shock, do not remove cover. Refer servicing to qualied service personnel.
This projector is equipped with a 3-blade grounding type plug to satisfy FCC rule.
If you are unable to insert the plug into the outlet, contact your electrician.
1.3 Important Safeguards
Electrical energy can perform many useful functions. This unit has been engineered and manufactured to
assure your personal safety. IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE
HAZARD. In order not to defeat the safeguards incorporated into this product, observe the following basic rules
for its installation, use and service.
The power input is auto-ranging from 100 to 240 VAC.
Do not install the projector in a place that cannot support its weight securely. If the installation place is not sturdy
enough, the projector could fall or overturn, possibly causing personal injury.
R699900 - Eos Series User Manual 5
Page 6
SAFETY INSTRUCTIONS
Please read these Important Safeguards carefully before use.
• All the safety and operating instructions should be read before the product is operated.
• All warnings on the product and in the operating instructions should be adhered to.
• All operating instructions should be followed.
• Place the projector near a wall outlet where the plug can be easily unplugged.
• Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use
a damp cloth for cleaning.
• Do not use attachments not recommended by the product manufacturer as they may be hazardous.
• Do not use this product near water. Do not use immediately after moving from a low temperature to high
temperature, as this causes condensation, which may result in re, electric shock, or other hazards.
• Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious injury
to a child or adult, and serious damage to the product. The product should be mounted according to the
manufacturer’s instructions, and should use a mount recommended by the manufacturer.
• When the product is used on a cart, care should be taken to avoid quick stops, excessive force, and uneven
surfaces which may cause the product and cart to overturn, damaging equipment or causing possible injury
to the operator.
Slots and openings are provided for ventilation must not be blocked or covered. Do not place this unit
on a bed, sofa, rug or other similar surface.
• This product should be operated only with the type of power source indicated on the label. If you are not sure
of the type of power supply to your home, consult your product dealer or local power company.
• This product is equipped with a three-wire plug. This plug will t only into a grounded power outlet. If you are
unable to insert the plug into the outlet, contact your electrician to install the proper outlet. Do not defeat the
safety purpose of the grounded plug.
• Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed
upon or against them. Pay particular attention to cords at doors, plugs, receptacles, and the point where they
exit from the product.
• For added protection of this product during a lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and disconnect the cable system. This will prevent damage to
the product due to lightning and power line surges.
• Do not overload wall outlets, extension cords, or convenience receptacles on other equipment as this can
result in a risk of re or electric shock.
• Never push objects of any kind into this product through openings as they may touch dangerous voltage
points or short out parts that could result in a re or electric shock. Never spill liquid of any kind on the product.
• Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous
voltages and other hazards. Refer all service to qualied service personnel.
• Unplug this product from the wall outlet and refer service to qualied service personnel under the following
conditions:
a) When the power supply cord or plug is damaged.
b) If liquid has been spilled, or objects have fallen on the product.
c) If the product has been exposed to rain or water.
d) If the product does not operate normally by following the operating instructions. Adjust only those controls
that are covered by the Operation Manual, as an improper adjustment of controls may result in damage
and will often require extensive work by a qualied technician to restore the product to normal operation.
e) If the product has been dropped or damaged in any way.
f) When the product exhibits a distinct change in performance - this indicates a need for service.
• When replacement parts are required, be sure the service technician has used replacement parts specied
by the manufacturer or with same characteristics as the original part. Unauthorized substitutions may result in
re, electric shock, or other hazards.
• Upon completion of any service or repairs to this product, ask the service technician to perform safety checks
to determine that the product is in proper operating condition.
• The product should be placed more than one foot away from heat sources such as radiators, heat registers,
stoves, and other products (including ampliers) that produce heat.
• When connecting other products such as VCR’s, and personal computers, you should turn off the power of
this product for protection against electric shock.
• Do not place combustible behind the cooling fan. For example, cloth, paper, matches, aerosol cans or gas
lighters that present special hazards when over heated.
6
R699900 - Eos Series User Manual
Page 7
INSTALLATION GUIDELINES
Do not look into the inside of this unit through vents (ventilation holes). Do not stare into the beam. The
light is so powerful that your eyesight can be impaired. RG2 from the IEC 62471-5:2015 classication.
• Do not drop, hit or damage the light-source lamp (lamp unit) in any way. It may cause the light source lamp
to break and lead to injuries. Do not use a damaged light source lamp. If the light source lamp is broken, ask
your dealer to repair it. Fragments from a broken light-source lamp may cause injuries.
• The light-source lamp used in this projector is a high pressure mercury lamp. Be careful when disposing of the
light source lamp. If anything is unclear, please consult your dealer.
• Do not ceiling-mount the projector to a place which tends to vibrate; otherwise, the attaching xture of the
projector could be broken by the vibration, possibly causing it to fall or overturn, which could lead to personal
injury.
• The power supply rating of this product is AC100V – AC240V, the power cord attached conforms to the
following power supply voltage. Use only the power cord designated by our dealer to ensure Safety and EMC.
• When it is used by other power supply voltage, power cable must be changed. Ensure that the power cable
used for the projector is the correct type for the AC outlet in your country. Consult your product dealer.
• Caution: Do not allow any unqualied person to install the unit. Be sure to ask your dealer to install the unit
(e.g. attaching it to the ceiling) since special technical knowledge and skills are required for installation. If
installation is performed by an unqualied person, it may cause personal injury or electrical shock.
1.4 Imageprojectorclassication
IEC62471-5 labels located at the top front of this unit.
As with any bright light source, do not stare into the beam when this unit is operating. This unit is rated
RG2 from the IEC 62471-5 classication.
2.0 INSTALLATION GUIDELINES
2.1 Introduction
The Eos Series projectors are equipped with a three-chip LCoS light engine capable of projecting a picture
resolution of 4096 x 2160 pixels (true 4K). The highest model of the Eos Series is the Eos Signature that can
display pictures up to 8192 x 4320 pixels resolution thanks to the new 8K Interpolation engine. 8K resolution is
more than 17 times Full-HD resolution.
Supported 2D signals and pixel depth
480p, 576p, 720p@50/60Hz, 1080i@50/60Hz, 1080p@24/50/60Hz
4Kp@24/25/30Hz and UHD: 3840×2160@24/25/30Hz (up to RGB and YCbCr 4:4:4 12 bits pixel depth)
4Kp@50/60Hz and UHD: 3840×2160@50/60Hz (YCbCr 4:2:2 up to 12 bits pixel depth or up to 8 bits for RGB and
YCbCr 4:4:4). Note that the native resolution of this projector is 17:9 ratio, 4096x2160 pixels, 16:9 signals such
as 3840x2160@24/25/50/60Hz or Full-HD are supported and will need to be masked on left and right to eliminate
light leaking on the sides of the screen.
Supported 3D signals
This unit is compatible with 3D playback. The source can be connected using one of the two available HDMI
inputs and will be up-scaled to 4K resolution. The inputs are compatible with the following 3D formats:
• 1080p @ 23.98/24 Hz - Frame Packing, Top & Bottom and Side-by-Side
• 720p @ 50 or 59.94/60 Hz - Frame Packing, Top & Bottom and Side-by-Side
• 1080i/p @ 50/60 Hz - Side-by-Side
R699900 - Eos Series User Manual 7
Page 8
INSTALLATION GUIDELINES
B
2.2 THX4KDisplayCertication(EosSignatureonly)
The THX 4K Display certication proves that the Eos Signature has undergone over 400
individual tests to ensure color, tone and images reproduce the director’s intentions accurately
in 4k: Amongst the important points, the THX labs have veried upscaling, motion processing,
correct gamma and color accuracy, overscan and scaling. The 4K Display label ensures that
the Eos Signature is capable of performing the best images and pristine video performances,
sharper pictures and nest Ultra-HD experiences.
2.3 Environment of Use
Do not install in this following conditions
This unit is a precision device. Please refrain from installing or using it at the following locations. Otherwise, it
may cause re or malfunction.
• Projection with the unit laid on sides.
• Dusty, wet and humid places
• Places subject to oily smoke or cigarette smoke
• On top of a carpet or bedding, or other soft surfaces
• Places exposed to direct sunlight
• Do not install this unit in a room that is oily or subject to cigarette smoke. Even a small quantity of smoke or
oiliness can have a long-term impact on this unit.
• Projection at a place exposed to air blasts from an air conditioner.
This unit produces a great amount of heat, and is designed to take in cool air to cool its optical components.
Using the unit at the above locations may cause dirt to attach to the light path, thereby resulting in dark
images or dull colors. Dirt that sticks to the optical components cannot be removed.
Allowed Inclination during operation
Due to the lamp position and operating angle, this unit cannot operate with more than 5° angle horizontally and
15° angle vertically. This unit cannot be operated on the side.
15°
5°
2.4 Air-Flow and Space Requirements
This unit can be installed in table, ceiling, rear table or rear ceiling position. Make sure that the unit is installed
within the space requirements described below (A: air inlets, B: air outlets). This unit needs at least 30 cm of nonobstructed space on each sides and 15 cm on top to allow sufcient air ow.
A
B
A
B A
B
8
A
Air ow.
R699900 - Eos Series User Manual
B
Page 9
INSTALLATION GUIDELINES
A
A
A A
2.5 Installing the projection screen
Install the projection screen and this unit such that they are perpendicular to each other as showed in the picture
below.
Place this unit perpendicular to the screen.
Use the electronic shift and zoom to correct the picture size and position as needed. You can also use
the feet to adjust the projected picture level.
Screen material suitable for 4K/8K projection.
To optimize the sharpness and detailing of the picture, please choose a screen material optimized for ultra High
resolution (UHD 4K) or 8K if you are installing a Eos Signature. Avoid any material with uniform patterns as
checks that may cause interference artefacts to occur. If this is the case, you can try to slightly change the size
of the projected image to make the interference patterns less noticeable.
2.6 When to use the High Altitude mode
When using this unit at a location that is higher than 900 meters or 3000 feet above sea level and making the air
pressure low enough to decrease its efcacity cooling this unit, set the “High Altitude Mode” to “On”.
2.7 Ceiling Mounting the Unit
d=290 mm
D=337 mm
When mounting of this unit is required, make use of the 4 screw holes (M5x20 screws) at the bottom of this unit
indicated by the letter A. You can remove the feet to insert the ceiling mount screws. Allow sufcient space around
the air inlets to avoid blocking them.
Precautions for Ceiling-mount
• To ceiling-mount this unit, special expertise and techniques are necessary. Be sure to ask your dealer or
specialist to perform mounting.
• Do not mount at places that may be subjected to vibration and shock.
• Depth of the screw holes (A) is 23 mm. Use at least 13 mm long screws but not longer than 23 mm as you
may damage inside the projector.
• Install at a safe place in case this unit or a part of it may drop. If the light-source lamp is broken, small pieces
R699900 - Eos Series User Manual 9
Page 10
INSTALLATION GUIDELINES
Horizontal Shift
of glass from the mesh of the lter may appear outside the unit.
• Regardless whether the unit is still under guarantee, Dreamvision is not liable for any product damage caused
by mounting the unit with third party ceiling mount or when the environment is not suitable for ceiling-mount.
Dimensions
• Distances between left and right holes is D = 337 mm.
• Distances between front and back holes is d = 290 mm.
2.8 Projection Distance
Projection Screen
Diagonal Size
(Aspect Ratio 16:9)
60” (152 cm) 52.3” (133 cm) 29.4” (747 cm) 178 cm - 366 cm
70” (178 cm) 61.0” (155 cm) 34.3” (872 cm) 209 cm - 428 cm
83” (211 cm) 72.3” (184 cm) 40.7” (103 cm) 251 cm - 507 cm
110” (279 cm) 95.9” (244 cm) 53.9” (137 cm) 331 cm - 675 cm
138” (350 cm) 120.3” (306 cm) 67.7” (172 cm) 418 cm - 843 cm
150” (350 cm) 130.7” (332 cm) 73.5” (187 cm) 453 cm - 860 cm
180” (457 cm) 156.9” (306 cm) 88.2” (224 cm) 545 cm - 1107 cm
200” (508 cm) 174.3” (443 cm) 98.1” (249 cm) 606 cm - 1230 cm
230” (584 cm) 200.5” (509 cm) 112.8” (286 cm) 694 cm - 1405 cm
250” (635 cm) 217.9” (553 cm) 122.6” (311 cm) 755 cm - 1528 cm
280” (711 cm) 244.0” (620 cm) 137.3” (349 cm) 846 cm - 1713 cm
• The projection screen sizes and projecting distances in the table above are provided only as a guide. Please
use them as reference during installation.
• 230” up to 280” diagonal screens available with Eos Signature models only.
Projection Screen
Base Size
(Aspect Ratio 16:9)
Projection Screen
Height
(Aspect Ratio 16:9)
Eos Series
Projection Distance
2.9 Setting the Lens and using Lens Memories
Adjust the picture position
The optimum image can be obtained when the centre of this projector’s lens and the screen are placed
perpendicular to each other.
+/- 34%
Vertical Shift
Screen Height
(H)
Screen Base
(B)
This unit comes with a vertical and horizontal shift to suit most installations. Make sure that your installation
does not exceed 80% vertical offset and 34% horizontal offset to avoid trapezoidal correction.
This unit comes with a optical shift that features vertical and horizontal adjustment of the projection screen
10
R699900 - Eos Series User Manual
+/- 80%
Page 11
INSTALLATION GUIDELINES
position.
Adjust the picture to your screen.
• The Vertical Shift level is between -80% and 80% of the Screen Height (0.80 x H).
• The Horizontal Shift level is between -34% and 34% of the Screen Base (0.34 x B).
• If the projector is not installed perpendicularly to the screen, use keystone correction to fulll your screen.
Note that using keystone correction, may be disabled by 3D projection. If you want the best possible 3D
pictures, It is not recommended to use trapezoidal correction.
• If you plan to use the vertical and horizontal shifts without keystone correction, make sure to not exceed the
values contained in the tab below for the Eos 1 and Eos 2:
Left / Right shift 0% 10% 20% 25% 30% 34%
max. up / down shift 80% 66% 47% 34% 18% 0%
• The Eos Signature has an extended shift range as follow:
Left / Right shift 0% 10% 20% 25% 30% 35% 43%
max. up / down shift 100% 87% 72% 58% 45% 22% 0%
•Adjust the picture position
The projector has motorized vertical and horizontal shifts. Browse into the Menu to the [Lens Control] setting
into the Installation menu, select the shift adjustment. Or use the direct access button on the Remote Control
Unit [Lens Control] to make the lens adjustment. You can use self-generated test pattern of the projector or an
external pattern, from a calibration DVD by example, by setting the Adjust pattern option to Off.
•Adjust the picture Zoom
Into the [Lens Control] menu, press the [Ok] button to access the Zoom adjustment. Use the up and down buttons
to adjust the picture size until the screen is completely lled.
•Adjust the Picture Focus
From the [Lens Control] menu, press the [Ok] button to access the Focus adjustment. Use the up and down
buttons to adjust the picture focus
Using Installation Modes
You can save the current picture position, zoom and focus into one of the 10 Installation Modes. Each Installation
Mode uses a memory that stores the current position, zoom, focus of the lens. Additionally, you can set a custom
name of 10 characters or less.
•Current lens setup
All the lens settings will be stored by default into the Installation Mode 1. You can also copy a Mode into another
using the Mode Copy function. Menu > Installation > Installation Mode > Mode Copy. Then you can call back
anytime later the current lens setup using the direct access button [Mode 1] up to [Mode 3] on the RCU.
•Limitations of use
Each memory can store a different picture size and position, but there are limitations on the possible pictures
sizes and positions because of the projector being at a xed location. In order to calculate the best position of the
projector toward the screen, the installer has to make sure that among the different desired pictures, the smaller
one with the smaller zoom, is within the offset limits (horizontal and vertical shifts) of the projector. Once the
position of the projector is determined by the smallest possible picture, double check that the larger one does not
exceed the zoom capacity.
R699900 - Eos Series User Manual 11
Page 12
REMOTE CONTROL UNIT (RCU)
3.0 REMOTECONTROLUNIT(RCU)
Stand by
Switch [INPUT]
[Hide] the current picture
Standby/ON LED will ash
green when picture is hidden
Display the main [MENU]
Display [PICT. MODE] menu
CMD Clear Motion Drive
M.P.C. Settings)
Power [On]
Display the Installation
Mode menu
[LENS CONTROL]
Focus, Zoom, Shift
Displays [Info] menu
Directional keys
Conrm button
[BACK] to previous menu
Display [COLOR PROFILE] Menu
Gamma Adjust
Displays [Advanced Menu]
Backlight button
12
The remote control unit can be used by having the signal reected off a screen, as the effect of signals
reected differs with the type of screen used, operable distance may decrease.
If the remote control has to be brought closer to the projector to operate, it means that the batteries are
wearing out. When this happens, replace the batteries. Always insert the batteries according to the +
and - marks.
R699900 - Eos Series User Manual
Page 13
4.0 GETTING STARTED
Operating LEDs
Front IR receiver
Inputs Panel
Navigation buttons
Main Power
4.1 General View
Front side
Optical Lens (/!\)
GETTING STARTED
Air outlet
(/!\)Optical Lens: This unit comes with a lens plastic cover that is used to protect the lens during transport.
Please remove the lens before rst operation.
Rear side
Air inlet
• Input Panel: connect your video source to the correct input.
• Main Power: connect the power cord as shown below.
Air outlets
Filter compartment
Air inlet
4.2 Connecting the Power Cord
• Before plugging in the Power Cord, ensure that all devices have been
connected to their respective inputs of this unit.
• Connect the power cord to the power input terminal of the projector.
When in Cool Down mode, do not pull out the plug from the outlet. Also, do not block the air inlets or
exhaust vents by standing the projector on its end or laying it on its side.
R699900 - Eos Series User Manual 13
Page 14
CONNECTIONS
Rear IR receptor
Back
4.3 Operating and Navigation Buttons
Directional keys
and input select
Power button
Menu
OK button
Button Description
Back To return to previous menu or cancel action.
Directional keys
and input select
Power button To display the On Screen Display (OSD) Menu.
Menu To display the On Screen Display (OSD) Menu.
OK button To select or to conrm action.
MENU
Use the Navigation Keys to navigate into the On Screen Display (OSD) Menu.
Up and Down keys may be used to switch Inputs between HDMI1 and HDMI2
when no OSD menu is shown.
5.0 CONNECTIONS
INPUT
BACK
OK
5.1 Caution when connecting a Device to HDMI Input
Prior to connecting any device to this unit, switch the projector in standby mode. Never connect a HDMI
source to this unit when the projector is in operate mode. The HDMI termination is a self-powered
connection and can cause electric discharges.
The HDMI 2.0 inputs are compatible with HDCP 2.2 and supports video signals up to 18 Gbps. It is
strongly recommended to use exclusively cables rated for 18 Gbps bandwidth to watch 4K contents,
otherwise this unit will suffer from handshake issues and video freezes.
14
R699900 - Eos Series User Manual
Page 15
5.2 Connecting a Video Source to the Projector
RF Dongle
or
3D syncro
Emitter
to LAN rooter
for Automation
12V Trigger
HDMI 1 HDMI 2
Audio/Video Connection Device to connect
HDMI 1, HDMI 2
(DVI compatible)
RF Dongle or 3D Synchro
Emitter
HDMI or DVI-D sources: Blu-ray Disc player, DVD-player equipped with an HDMI
output, Game Console, Computer with DVI-D output.
Connect the RF Dongle emitter to control the active 3D shutter glasses or any
other 3D Synchro apparel. 3-PIN mini-DIN interface, 12V.
CONNECTIONS
This unit supports up to 4Kp60 inputs, make sure to use high quality HDMI cables rated for at least 4K
HDMI 2.0 standards (18 Gbps).
5.3 Connecting an Automation or Control device
RS-232C
for Automation
Connection Device to connect
RS-232 C Automation Device, Control Device or Computer with RS-232 capability.
12V Trigger DC power supply output 12V@100mA to control either a screen or an anamorphic
lens motorization.
LAN Automation Device, Control Device or Computer with RJ-45.
R699900 - Eos Series User Manual 15
CONNECTING AN AUTOMATION/CONTROL DEVICE
This unit can control or be controlled by using several input/output terminals. Each terminal is ruled by
specic protocols. Please refer to Appendix for more information.
ECO Mode turn to On prevents this unit to receive and to respond to automation commands when it is in
standby. Turn Off ECO mode if you plan to take full control of this unit with an automation system.
Page 16
FIRST START Up
RCU
6.0 FIRST START UP
Always remove the lens cover or lens protection before powering up this unit. To power up this unit,
make sure that the power cord is connected to the power input terminal.
6.1 Turn the power ON
You can turn ON this unit with the remote control unit (RCU) or directly pressing the power button located on the
back panel. During startup procedure, this unit Standby/Power LED will blink green. Wait until complete power
ON indicated by a steady green light on the Standby/Power LED.
Back panel
If “Eco mode” is On, the standby led will not be light up red during Standby mode.
Select the correct Input
Once this unit is powered ON, please select the correct Input by pressing the corresponding button on the
Remote Control Unit or the O/I button on the back panel of this unit.
6.2 TurnthePowerO
You can turn OFF this unit by using either the RCU or the Power button on the rear control button panel.
Press the Standby button and a message appears on the screen to ask to conrm the command. You can cancel
the command by pressing the “Back” button or turn off the device by pressing the “Standby” button again.
The Standby LED will switch from steady green to blinking red light and the fans will run for about 10 seconds
to nish the shutdown procedure. During this Cool-down sequence, do not disconnect the power cord. The cooldown procedure is nished when the “Standby/On” LED indicator stops blinking red and switches to a solid red.
16
The power cannot be turned off within approximately 80 seconds after it has been turned on.
The power cannot be turned On again until the Cool-down sequence (10 seconds) is complete.
It is recommended to disconnect the power plug when the unit is not to be used for a prolonged period of
time (superior to one week) to avoid any electrical hazards.
R699900 - Eos Series User Manual
Page 17
7.0 MENU STRUCTURE
MAIN MENU SUBMENU AVAILABLE OPTIONS
Picture Adjust Picture Modes
(4+6 User)
Expert Picture Modes
(*) require individual calibration
Advanced Picture Mode
(press OK to enter this menu)
Color Proles
the list varies upon the selected
Picture Mode
(*) require individual adjustment
and/or calibration
Advanced Color Prole Color Management: Off / On
Color Temp Xenon Modes
Advanced Color Temp If Custom 1-2, choose Correction Value
Gamma If Color Prole is Film1 or 2
(Video and drama programs) Natural
(Vivid colors suitable for all movies) Cinema
(HDR10 movies, auto tone mapping) HDR10
(HDR movies using Hybrid Log) HLG
(Movie lms, Eos 2 & Eos Signature) Film
(Eos Signature only) THX
User 1 - 6
THX bright(*)
THX dark(*)
Lamp Power Low, High
Aperture Auto 1
Auto 2
Manual: -15 +0
User Name Edit (if f User 1 - 6 selected)
Edit name 10 char. max
(HDTV REC-709) BT.709
(Movies REC 2020) BT.2020
(Cinema DCI-P3) DCI
(Drama or Live events) Video
(Animations) Anime
(Movies with enhanced colors) Cinema
(HDR contents) HDR
(Eastman Kodak movies) Film1
(Fujilm movies) Film2
(Eos Signature only) THX
Off
Custom 1 - 6(*)
Color selection
Axis Position -30 +30
Hue -30 +30
Saturation -30 +30
Reset Conrm
(Film projector) Xenon 1
(DCI projector) Xenon 2
Preset value:
5500K, 6500K, 7500K, 9300K,
High Bright, HDR10, HLG, Custom 1-2
Gain and Offset settings
Reset Conrm
(Eos 2 & Eos Signature only)
(standard) Film1
(more contrasted) Film2
Custom1 to 3
If Color Prole is THX (Eos Signature) THX
If Color Prole is not Film nor THX
Normal, 2.2, 2.4, 2.6,
Cinema 1, Cinema 2
HDR (PQ), HDR (HLG)
Custom 1, Custom 2
MENU STRUCTURE
R699900 - Eos Series User Manual 17
Page 18
MENU STRUCTURE
Picture Adjust Advanced Gamma If Custom 1 or 2, Gamma Corr. Value
1.8 - 2.6 (within 0.1 steps)
Cinema 1, Cinema 2
HDR (PQ), HDR (HLG)
Import
Auto Tone Mapping On, Off
Mapping Level -7 +7
Color Selection White / Red / Green / Blue
Picture Tone -16 +16
Dark Level -7 +7
Bright Level -7 +7
Reset Conrm
MPC Level / MPC e-shift 8K e-shift (Eos Signature only, NA with 3D)
On(8K), Off(4K)
Graphic Mode Standard, High-Res (4K)
Enhance 0 - 10
Smoothing 0 - 10
Noise Reduction 0 - 10
Reset Conrm
Motion Control Low Latency (NA with 3D and if CMD is On)
On, Off
Clear Motion Drive (NA if Low Latency is On)
Off, Low, High, Inv. telecine
Motion Enhance (NA with 3D) Off, Low, High
Contrast -50 +50
Brightness -50 +50
Color -50 +50
Tint (reddish to greenish) -50 +50
Reset Prole settings Conrm
Input Signal Input level Auto
16 - 235 (Video)
0 - 255 (PC)
16 - 255 (S. White)
Color Space Auto,
YCbCr444
YCbCr422
RGB
3D Setting 3D format
Auto / Side-by-Side / Top & Bottom / 2D
Parallax -15 +15
Crosstalk Cancel -8 +8
HDR Settings HDR10 Auto Select HDR10, User 1 to 6, Off
HLG Auto Select HLG, User 1 to 6, Off
HDMI2 EDID (HDMI2 only) A, B
Installation Installation Mode Mode Select Mode 1 - Mode 10
Name Edit 10 char. max
Mode Copy Select Mode and Conrm
Lens Control Focus
Zoom
Shift
Image Pattern On, Off
Lock On, Off
Lens Center Conrm
Pixel Adjust Adjust On, Off
Adjust Area Whole, Zone
Adjust Color Red, Blue
Adjust Pattern On, Off
Adjust Pattern Color White - Cyan/Yellow
18
R699900 - Eos Series User Manual
Page 19
MENU STRUCTURE
Installation Pixel Adjust Adjust (Pixel)
Adjust (Fine)
Reset Conrm
Mask On, Off
Top, Bottom, Left, Right 0 - 220
Anamorphic Off, A, B, C
Screen Adjust
(Color Prole must be On)
Installation Style Front, Ceiling Mount, Rear, Ceiling Mount (Rear)
Keystone (vertical) (N.A. if Pincushion is On) -16 +16
Pincushion (N.A. if Keystone On) 0 - 16
Aspect Zoom
Display Setup Back Color (when no signal) Blue, Black
Menu Position select position
Signal Display (active input) On, Off
Logo On, Off
Language select between 13 languages
Function Trigger Off
Off Timer (in hours) 1H, 2H, 3H, 4H, Off
ECO Mode On, Off
Network DHCP Client On, Off
Remote Code Press [Menu] + [Back] A, B
High Altitude Mode (900m or higher) On / Off
Lamp Reset
Factory Reset
Software Update
Information Display Information menu
Screen No. 000 - 255
On, Off
Auto
Native
Power
Anamo
Inst. Mode 1 - Inst. Mode 10
IP Address 192.168.0.2
Subnet Mask 255.255.255.0
Default Gateway 192.168.0.254
Mac Address Display MAC
Set Conrm
R699900 - Eos Series User Manual 19
Page 20
pICTURE ADjUST
8.0 PICTURE ADJUST
8.1 PictureModesandColorProles
The preset Picture Modes are available and they can be applied to any input. A picture mode retains the picture
adjustments. When adjusting the Picture Mode, you can also select pre-congured Color Proles.
Type of source Movie
or HDTV
Picture mode Cinema Natural HDR10 / HLG Film THX
BT.709 BT.709 BT.709 Film 1 THX
BT.2020 BT.2020 BT.2020 Film 2
Color Proles
There is a total of 6 Picture Mode presets for Eos 1, 6 for Eos 2 models and 5 User. For each prole, you may
choose one of the available Color Prole presets:
• Film 1 available with Film Picture Prole, uses the Xenon lter and adjusted to Eastman Kodak lm tone
• Film 2 available with Film Picture Prole, uses the Xenon lter and adjusted to Fujilm lm tone.
• Film 3 available with Film Picture Prole, uses the Xenon lter and adjusted to Technicolor lm tone.
• Standard will bring rich and saturated colors found in HDTV, using REC 709 color space.
• Cinema 1 available with Cinema Picture Prole and adjusted to movie sources with bright, saturated colors.
• Cinema 2 available with Cinema Picture Prole and adjusted to DCI-P3 color space.
• Animation/Anime 1 best suited to Hollywood animations.
• Anime 2 best suited to Japanese animations.
• HDR10 that is best suitable for HDR movies in general.
• BT.2020 that is optimized for HDR movies encoded with REC 2020 color space.
• Video color prole is best suited to TV and Sport programs.
• Reference color prole is used to reproduce faithfully the source colors.
• THX color prole is reserved for the THX picture modes.
DCI DCI DCI
Video Anime HDR
HDR HDR
Dramas
or Videos
HDR sources Film THX
8.2 Advanced Picture Mode
Lamp Power
Set the lamp power used by the current Picture Prole. For standard viewing conditions, the lamp power is set to
Low. To obtain a brighter image, set it to High but this setting may cause the lamp to darken faster.
Aperture and High Contrast Images
The lens is equipped with a variable electronic aperture. This function is used with a real time analysis of the video
picture projected that optically adjusts the light output depending on the viewing conditions by controlling the
aperture dynamically. Thanks to sensitive and perfectly controlled adjustments, the contrast image is drastically
boosted. When set to Auto 1, this setting makes the iris to automatically set to the optimal opening to enhance
the picture contrast. The Auto 2 setting, the result obtained is altered so that the gradation is more visible. The
Manual setting sets the iris to a xed position, adjust the aperture from partially closed (-15) to fully opened (0).
User Name Edit
You can edit the picture modes names User 1 to User 6 using a maximum length of 10 characters. You can use
alphabet letters, numbers and symbols:
20
R699900 - Eos Series User Manual
Page 21
pICTURE ADjUST
User Name Edit
MENU
BACK
>
>
Name
User 1
Clear
All Clear OK
Exit
Select
Operate
Picture Adjust
SPACE
Select cursor
Input cursor
Character list
a) Select the user name you want to edit from User 1 to User 5. Press [OK] to enter the edit mode.
b) The input cursor displays the place where the new character will be insert. It moves automatically as a
character is selected. Use [UP], [DOWN], [LEFT] or [RIGHT] to select a character and press [OK] to insert.
c) Press [BACK] to exit edit mode.
Clear: To delete a character: Move the cursor to the desired location and press [OK] to delete the specic
character. All Clear: To delete all characters. OK: To save the current name, a save conrmation will appear.
8.3 AdvancedColorProle
Expert Calibration is accessed only by using a programmable IR-RCU, RS-232C or LAN control. Two additional
sets of Picture Modes can be activated. Each set designated as THX and ISF proles have to be calibrated. Once
done, these proles are stored and displayed in the picture mode menu list but will not be modiable. Additionally
the Calibrator can certify his action by setting in the Information Menu his name or company name.
Color Management (TSL adjustments)
The Color Management gives the installer an unique calibration ease with the integrated Color Adjustment menu:
each primary, secondary colors can be independently calibrated to obtain a precise color balance in a snap.
Adjust the Red, Green, Blue, Yellow, Cyan, Magenta. Tints, their saturations and luminances and store them into
Custom proles.
8.4 Color Temperature
Color temperature stands for the spectral properties of a light source. Low color temperature implies warmer
ambiance (more yellow/red) while high color temperature implies a colder light (more blue). Depending on the
Picture Prole selected, this setting can be set to:
• Preset from warm colors 5500K, 6500K, 7500K up to 9300K, colder colors.
• Xenon 1 uses the Xenon lter and color compensation to reproduce a lm projector
• Xenon 2 uses the Xenon lter and color compensation to reproduce a digital cinema projector
• HDR10 Color temperature is suitable for viewing HDR10 content and the default setting is 6500K.
• HLG is suitable for viewing HDR with Hybrid Log contents and the default setting is 6500K.
• High Bright used for maximum brightness output.
• Custom 1 to 2 that can be used to adjust color temperature to specic environment.
A Custom setting allows a ne adjustment of a Color Temperature by selecting it in the Correction Value menu.
Adjust the Gain values (bright part) and Offset values (dark part) for each color Red, Green and Blue.
Accurate color temperature may require professional tools such as dedicated software and color-meter.
Wait at least 15 minutes after startup for the colors to stabilise before modifying the picture settings.
Picture modes Xenon 1 and Xenon 2 are exclusive to Eos 2 and Eos Signature models only.
R699900 - Eos Series User Manual 21
Page 22
pICTURE ADjUST
8.5 Advanced Color Temperature
When selecting a Color temperature, you can manually set the Gains and Offsets of each primary color: red,
green and blue to nely adjust the color balance.
8.6 Gamma
Gamma is the relationship between the color values of the data and the color values displayed. The Gamma
coefcient makes it possible to adjust the brightness of the mid tones only without affecting the very bright and
very dark areas. If gamma is set too high, middle tones appear too dark. If it’s set too low, middle tones appear
too light. Depending on the current active Picture mode, the Gamma setting can be set to:
• Numeric value of 2.2, 2.4 or 2.6
• Film1: standard gamma
• Film2: slightly more contrasted gamma
• Cinema 1: emphasis on gradations
• Cinema 2: emphasis on contrast
• HDR(PQ): suited for HDR contents that uses with a Perceptual EOTF Gamma (HDR10)
• HDR(HLG): Suited for viewing broadcast HDR contents such as ones by BBC or NHK
• Normal: Standard setting for normal viewing.
• THX: video gamma of THX standard (exclusively on Eos Signature model)
• Custom 1 to Custom 3: ne tune the gamma setting according to the user’s preference.
Picture mode Natural Cinema Film HDR THX
2.2, 2.4, 2.6 2.2, 2.4, 2.6 Film 1 2.2, 2.4, 2.6 THX
Gamma.
Cinema 1 or 2 Cinema 1 or 2 Film 2 Cinema 1 or 2
HDR(ST.2086) HDR(ST.2086) HDR(ST.2086)
HDR(Hybrid Log) HDR(Hybrid Log) HDR(Hybrid Log)
8.7 Advanced Gamma
Correction Value
The Custom data can be set to a correction value: a numeric value that will act as a gamma coefcient between
1.8 and 2.6, Normal, A, B, C, HDR(Hybrid Log), HDR(ST.2084) or Import.
Color Selection
Select the color to which the Picture Tone, Dark / Bright Level settings would apply. Choose between White, Red,
Green and Blue.
Picture Tone
It allows a ne adjustment steps of the global picture brightness while maintaining the correct contrast level to
keep good black and bright levels. Sets the overall exposure from -16 (under-exposed, darker) up to +16 (over-
exposed, brighter)
Dark / Bright Level
This setting modies the gamma curve locally in the dark and bright areas.
• Dark Level adjust gamma curve between 0 IRE and 15 IRE, each color can be adjusted from -7 to +7.
• Bright Level adjust gamma curve between 85 IRE and 100 IRE, each color can be adjusted from -7 to +7.
Reset Gamma
Prompt a conrmation to reset the current Gamma settings to default.
22
R699900 - Eos Series User Manual
Page 23
pICTURE ADjUST
8.8 MultiplePixelControlLevel(MPCLevel)
The MPC Level control gives control over the video processing parameters in order to ne tune the global picture
sharpness and quality.
8K E-shift (N.A. with 3D)
• On: sets this unit to upscale the content in 8K resolution.
• Off: sets this unit to display the video content in 4K resolution. Off with 3D input.
Graphic Mode
Select whether the content needs a high precision (strong sharpness) or if it is a graphic. Preferably sets this
setting to Standard when watching Blu-Ray movies and set to High-res when viewing UHD movies or “Mastered
in 4K” contents.
Enhance
Enhance: enhances the sharpness of foreground objects detected in the picture.
Smoothing
Smoothing: enhances the blurriness of backgrounds for increased the global sense of depth.
Noise Reduction
Noise Reduction: reduces the digital noise of the video picture.
8.9 Motion Control
Low Latency
To drop the latency drastically to the cost of picture enhancement process. Set to On when playing video games
or when installed for real-time simulators. High bandwidth signals such as 4K 10-bit and 12-bit signals can be
processed without being converted. This allows a video to be shown without losing its original quality, thereby
enabling the enjoyment of contents such as movies and concerts at higher quality. When set to On, Clear Motion
Drive will be disabled.
Low Latency cannot be used with 3D inputs or with Clear Motion Drive being On.
Clear Motion Drive
The Clear Motion function uses up to 400Hz video processing to render a smooth motion for movies shot at 24Hz
or HD movies at 60Hz. Clear Motion Drive is disable if Low Latency is On. Set the correct level between:
• Off: Frame interpolation is disable.
• Low: light frame interpolation with reduced artifacts equivalent to a 200Hz processing rate.
• High: strong interpolation up to 400Hz processing rate.
• Inverse Telecine: dedicated interpolation for 60i and 60p sources originally shot in 24p. N.A. for 24Hz input.
Motion Enhance (N.A. with 3D)
This setting enhances the responsiveness of each video frame by reducing the image blurring.
• Off: correction is disable. Automatically set Off with 3D inputs.
• Low: this setting reduces image blurring.
• High: stronger reduction of image blurring.
This setting enhances the responsiveness of each video frame by reducing the image blurring.
8.10 Contrast
The contrast function is used to adjust the contrast between the light and dark areas of the displayed image. A
correct contrast setting is important for good image reproduction. Adjust the Contrast value between -50 and 50.
8.11 Brightness
The brightness function is used to adjust the overall light output. Adjust the Brightness value between -50 and 50.
R699900 - Eos Series User Manual 23
Page 24
4K INpUTS
8.12 Color
The Color function is used to adjust the saturation levels. Adjust the Color value between -50 and 50.
8.13 Tint
The hue function is used to adjust the color tint to obtain true color reproduction. Adjust the Tint value between
-50 (more red) and 50 (more green).
9.0 4K INPUTS
9.1 Choosing the correct Input level
Because the Input level of 4K sources are generally “(0-255) Enhanced” input levels, and at the contrary, classic
Blu-Ray discs and HDTV programs use “(16-235) Standard” Input levels. It is important to clearly identify and to
select the correct input level to achieve perfect blacks.
To identify the correct level, you can for example select a dark scene from your movie and switch between
Standard and Enhanced Input levels. The correct Input level would be “Enhanced” if this setting gives the
deepest blacks. If both settings give the same result, then your source uses “Standard” levels.
Generally UHD sources use Enhanced levels: You may try to congure your UHD player to output
Standard levels to be consistent settings with Bluray playback.
Menu => Input Signal => Input level => (0-255) Enhanced
9.2 High Dynamic Range sources
Identifying HDR sources.
HDR sources are almost exclusively from the latest UHD discs or TV/internet streaming video that come with a
HDR logo. If your player supports this format, this unit should automatically detect the HDR format thanks to the
HDMI 2.0 handshake and the projector should apply automatically the correct Color Prole “HDR”. Make sur that
the correct Gamma is selected depending on your source: Hybrid Log, ST.2084 or Standard.
It is important to determine which color prole it uses between REC-709, DCI-P3 and BT-2020. Choosing the
correct gamma and color prole is very important to obtain the best performances from your source and to have
a perfect colorimetry with a greater sense of depth.
Correct Gamma settings
If the source is clearly identied to be using High Dynamic Range, the projector should display “HDR:
YES” in the Menu > Information Menu and the Picture Mode “HDR” should be applied automatically.
If your HDR image seems dull and without depth, check in the Menu > Information and check if the correct Color
Prole has been applied, and that the Colorimetry is HDR. If this is the case, you can also switch the Color Prole
from HDR to BT.2020.
Menu => Picture Mode => HDR10
Menu => Picture Adjust => Color Prole => HDR (slightly brighter than BT.2020) or BT.2020
HDR10 Auto Tone Mapping
Depending of the movie and its director, picture grading varies diversely between each movie. Some content being
made brighter and others darker. Enabling the “Auto Tone Mapping” function, allows the projector to adjust the
HDR gamma automatically by reading and applying the optimal brightness based on the mastering information
(Max CLL/Max FALL) contained in the HDR10 content. You can manually
HDR10 Mapping Level
Mapping Level is an independant adjustment that determines the picture brightness base level. Raise or lower
the Mapping Level to obtain the best overall brightness tting your screen size and material gain. By default the
middle setting (“0”) will be adapted to a screen diagonal of 100” (2m20 wide) and a gain of 1.0. Increase this value
24
R699900 - Eos Series User Manual
Page 25
4K INpUTS
to raise the global brightness or lower its value if the picture is too bright.
Tone Mapping or manual HDR10 Gamma Adjustment
Depending on the source or the content, this information may be wrong and manual setting is needed to obtain
a perfect picture
Tweaking for 1000 nits MaxCLL (UHD Bluray standards)
• Picture Tone: -7
• Dark Level: 0
• Bright Level: +7
Tweaking for 400 nits MaxCLL
• Picture Tone: +5
• Dark Level: 0
• Bright Level: +7
Tweaking for 2000 nits MaxCLL (UHD Bluray standards)
• Picture Tone: -9
• Dark Level: 0
• Bright Level: +7
Tweaking for 4000 nits MaxCLL (UHD Bluray standards)
• Picture Tone: -13
• Dark Level: 0
• Bright Level: +7
If the HDR picture seems a little dull or too dark
If the MaxCLL/MaxFALL values do not correspond, the picture will look a little dull or too dark, you can change
the adjustments as described below:
• Picture Tone adjustment: this adjustment changes the overall brightness of the picture. decrease the value
to obtain a brighter picture, recommended for larger screens or if the actual MaxCLL is lower than 1000 nits.
• Dark Level: rise this level if the blacks are still too deep
• Bright Level: There are several HDR encoding with different maximum brightness. Rise this level if the white
portions of the picture are not totally light up.
9.3 4KcontentsandtheirColorProles
How to identify BT-2020 sources
Most UHD discs and 4K sources would use BT-2020 colors. Eventually, that means that they can use REC-709
or DCI-P3 colors encapsulated into the BT.2020 color space instead of a true native BT-2020 color prole. Since
this unit can only detect the color prole and not the encoding, in a few cases, it is better to use a standard color
prole such as Cinema for DCI-P3 colors or Standard for REC-709 colors.
•Standard HDTV (REC-709) colors:
Menu > Picture Adjust > Color Prole > BT.709
•Movies encoded with richer colors:
Menu > Picture Adjust > Color Prole > Cinema or DCI
•REC-2020 colors:
Menu > Picture Adjust > Color Prole > HDR or BT.2020
If the colors seem wrong with BT-2020 Color Prole, you can switch to a any existing Color Prole that
would be more suitable such as Cinema for DCI colors or even BT.709 colors.
R699900 - Eos Series User Manual 25
Page 26
INpUT SIGNAL
10.0 INPUT SIGNAL
10.1 Input Level
Sets the dynamic rang of the video input:
• Auto: The input dynamic range is automatically detected and congured.
• Standard: Force dynamic range to 16-235.
• Enhance: Force dynamic range to 0-255.
• Super White: Force dynamic range to 16-255.
10.2 Color Space
Sets the color space of the input signal.
• Auto: The source color space is automatically detected and congured.
• YCbCr(4:4:4): Set color space to YCbCr 4:4:4.
• YCbCr(4:2:2): Set color space to YCbCr 4:2:2.
• RGB: Set color space to RGB 4:4:4.
Use preferably a video source of 4K if available to obtain higher resolution and richer colors.
10.3 HDR Setting
HDR10 Auto Select
This projector can detect HDR10 video contents. This setting congures the projector behavior when such packets
are detected so it can automatically switches the “Picture Mode” to either “HDR10” or any other congurable
“User 1 to 6” Picture Mode when the active input is detected as HDR 10 content.
• Set it to HDR10 to automatically switches “Picture Mode” to “HDR10” when receiving HDR10 packets.
• Set it to User 1 up User 6 to automatically switches “Picture Mode” to desired User Mode when receiving
HDR10 packets.
• Set to Off to prevent this unit to switch Picture Mode when receiving HDR10 packets
HLG Auto Select
This projector can detect Hybrid Log video contents. This setting congures the projector behavior when
such packets are detected so it can automatically switches the “Picture Mode” to either “HDR10” or any other
congurable “User 1 to 6” Picture Mode when the active input is detected as HDR 10 content.
• Set it to HLG to automatically switches “Picture Mode” to “HLG” when receiving Hybrid Log packets.
• Set it to User 1 up User 6 to automatically switches “Picture Mode” to desired User Mode when receiving HLG
packets.
• Set to Off to prevent this unit to switch Picture Mode when receiving HLG packets
10.4 HDMI2 EDID
This setting changes the EDID information for HDMI 2 only to make it compatible with older HDMI sources. If this
unit is not able to display 1920 x 1080 or lower resolutions pictures, connect this source to HDMI 2 terminal and
change this setting to value B.
26
R699900 - Eos Series User Manual
Page 27
3D CONTENT AND 3D pROjECTION
11.0 3D CONTENT AND 3D PROJECTION
11.1 General Information about 3D playback
Comfort and Caution with 3D Content
The closer one looks at stereoscopic images, the greater the binocular disparity, which means greater perception
of outward projection. At the same time, the spectator must focus on these outward objects on the screen. The
projecting image and the real focus distance cause a great contradiction, this strain contributes to fatigue and
discomfort.
Please stop watching if you do not feel well and consult a physician if necessary. People who already
have a kind of photosensitivity, sufferers from heart disease, and people in poor physical condition should
not watch 3D stereoscopic images. It is also recommended that you take a break periodically.
Prevent child under 5 years old to watch 3D
The comprehensive brain function to judge stereoscopic vision which includes the feeling for real distances,
develops while growing up by touching and seeing real objects, but in early childhood, it is still in an underdeveloped
state. Even though there are individual differences, children under 5 are still developing. Letting them frequently
watch stereoscopic 3D images can be an obstacle for the development of a comprehensive three-dimensional
feel. Additionally, younger children may suddenly become sick, because they continue watching without realizing
symptoms like 3D sickness or deterioration of health. Please accompany your child while it watches 3D programs.
11.2 3D Settings
3D Formats
Use this function to choose the correct 3D input format. Some input signals may contain 3D data such as 1080p
Side-by-Side but encoded as if they were in 2D. This unit may treat them as standard 2D signals and will not
project correctly. In such cases, congure the signal manually between Side-by-Side, Top & Bottom and 2D. In
other cases, you may select Auto setting.
Parallax
Use this function to adjust the amount of misalignment of the left and right 3D video images. Adjust settings
according to your preference between -15 and +15.
Parallax is an important parameter for 3D movies that directly affects comfort during 3D projection.
Because the parallax value changes with the screen size, it is important to set this parameter to a value
with which everyone feels comfortable with the 3D effect. In general, women and children will feel better
with a smaller parallax value. Do not hesitate to alter this settings if you feel eye-strains or headaches.
Due to the large screens used in home theaters compared to at screen TVs, we recommend a negative value
of -6 for computer sources and video games in native 3D with large parallax. This setting is best at 0 for Bluray
movies aimed for Digital-Cinema audience.
Crosstalk Cancel
Can be adjust with a 3D signal input. This function lessens the residual cross-talk found between 3D left and
right images. Adjust the Parallax value and then the Cross-talk settings in order to cancel the residual cross-talk
without loosing picture quality. Adjustments: -8 +8
Negative values reduce visible Crosstalk, positive values bring a brighter 3D picture at the cost of more
Crosstalk.
Connecting the 3D synchro emitter
Make sure that the RF dongle or IR Emitter is correctly connected to the “3D synchro” output located at the rear
panel of this unit.
R699900 - Eos Series User Manual 27
Page 28
3D CONTENT AND 3D pROjECTION
(B) Power button
3D video inputs limitations
When a 3D Signal is input, the following settings are automatically disabled:
• Menu => Picture Adjust => MPC e-shift => 8K e-shift interpolation is turn Off (Eos Signature only)
• Menu => Picture Adjust => Motion Control => Motion Enhance is turn Off
11.3 Operating the 3D Glasses
Indicating LED (A)
Optical Lenses
Indicating LED (A)
Optical Lenses
RF 3D Glasses
(B) Power button
(C) 3-Positions button
Micro USB slot
Charging the 3D Glasses
The 3D Glasses come with a USB rechargeable battery that is charged using the USB to micro USB cable.
Connect the cable to the micro USB slot. The indicating LED (A) will light On red continuously during the charge.
The glasses are fully charged when the indicating LED (A) switches Off.
Turning On your 3D Glasses
• Press the Power Button (B) once.
• The indicating LED (A) will light On and the Optical Lenses will blink alternately left and right to indicate that
they are ready to synchronize with the 3D synchro emitter.
Due to software limitations, the 3-Positions button (C) is inactive.
Turning Off your 3D Glasses
To turn Off the glasses, press and hold the Power button (B) for 3 seconds until the indicating LED (A) switches
Off. The glasses will also automatically switch Off after 5 minutes that the 3D synchro signal has stopped.
3D Glasses battery level
The battery allows up to 75 hours of continuous power. A low power level, below 30%, is indicated by a single
ash of the Indicating LED (A) at the 3D glasses switch On. Power level between 30% and 90% is indicated by 2
ashes. 3 ashes indicates that the power is above 90%
Auto Power Off
The 3D Glasses are programmed to automatically stop functioning after 5 minutes of immobilization or 10 minutes
without a 3D synchro signal. To turn them back On, just press the Power Button (B) once.
28
R699900 - Eos Series User Manual
Page 29
INSTALLATION
12.0 INSTALLATION
12.1 Installation Modes
An Installation Mode is a memory slot that collectively manages the setting values of “Lens Control”, “Pixel
Adjust”, “Mask”, “Anamorphic”, “Screen Adjust”, “Installation Style”, “Keystone”, “Pincushion” and “Aspect” There
are a total of 10 Installation Modes.
Mode Select
Selects a specic memory amongst the 10 available. Setting values can be set from Installation Mode 1 up to
Installation Mode 10.
Name Edit
Each Installation Mode can be renamed using “Name Edit”. You can use up to 10 characters that can be alphabets
(upper or lower case), numeric characters and/or symbols.
Mode Copy
The Mode Copy can be used to easily duplicate a selected Mode into the current Mode. Select the mode to copy
to and press the [OK] button to conrm.
12.2 Lens Control
Focus / Zoom / Shift
Adjust the lens focus / Zoom or Shift to obtain a clear picture.
Image Pattern
If set to On, an internal pattern will be generated to adjust the current setting. If you want to use an external
generator, turn this option to Off.
Lock
Once the Lens is correctly set, you may lock this setting menu by turning the Lens control Lock to On. Any attempt
to access the Lens control menu will lead to the display of a warning message.
Lens Center
Reset the lens position to the original, central position.
12.3 Pixel Adjust
The pixel adjustment is extremely ne: each color can be adjust within 1/16 pixel steps on 121 individual
adjustment zones.
Adjust
Enable the pixel adjustment on Memory 1, Memory 2 or Off.
Adjust Area
Whole: the entire screen is selected for adjustment.
Zone: the screen is divided into 121 adjustment zones.
Adjust Color
Select the color to adjust: Red or Blue.
Adjust Pattern Color
Select a pattern to help the pixel alignment. Settings: White or Green+adjusting Color. Yellow for red, Cyan for
blue.
Adjust (Pixel)
This function is enable when the Adjust Area is set to Zone only. You can adjust the selected color position
R699900 - Eos Series User Manual 29
Page 30
INSTALLATION
2.35:1 source with lens Mode A with lens
16:9 source with lens
Mode B with lens
horizontally and vertically by 1-pixel steps.
• H settings: -2 +2
• V settings: -2 +2.
Adjust (Fine)
Use this function to move the selected color within smaller steps.
• H settings: -31 +31
• V settings: -31 +31
Reset
Reset all pixel adjustments to default factory settings.
RCU SHORTCUTS DURING PIXEL ADJUSTMENT:
[GAMMA] button on the RCU switches adjust color parameter between Red and Blue.
[PIC. ADJ.] button on the RCU switches the adjust area parameter between whole and zone. At the same
time, the zone cursor will appear on the adjust pattern.
[COLOR SPACE] button on the RCU changes the adjust pattern from white to green+adjust color.
Use the [COLOR TEMP] button on the remote control to change adjustment method from Pixel to Fine
tune and switch to the ne tune window.
[BACK] button will exit the Pixel Adjust mode.
12.4 Mask
This setting turns off the active pixels on the screen borders. Default value is Off.
Turn it On to hide specied ranges on Top, Bottom, Left and Right borders from 0 up to 220 pixels.
To adjust the 17:9 native format of the D-ILA panels to 16:9 screens, you can set the left and right masks
to 64 pixels.
12.5 Anamorphic
• Anamorphic Modes
• Off: No modication to original picture.
• Mode A: The picture is vertically stretched to t an installation with anamorphic lens. A cinemascope picture is
stretched to completely ll the panel height, using 3840 pixels width.
Anamorphic Mode A with a cinemascope video.
• Mode B: This setting squeezes horizontally the picture to t a 16:9 image into a cinemascope screen. This
setting is to be used with an anamorphic installation where the lens is permanently xed in front of the unit and
to watch 16:9 content in its original format.
Anamorphic Mode B with a HD video.
• Mode C: This setting enlarges proportionally the picture until it occupies the full width of the panels. This
setting is to be used to display a cinemascope picture without an anamorphic lens but using the full width
capacity (4096 pixels) of the panel’s resolution. Optimal use when combining this setting with lens zoom
memories.
30
R699900 - Eos Series User Manual
Page 31
INSTALLATION
2.35:1 source
Mode C without lens
160
Anamorphic Mode C with a cinemascope video.
12.6 Screen Adjust and Screen No.
This setting corrects the color balance derived from the reective characteristics of the screen without altering the
global picture settings. You may select the best template available in the Screen No.
a) 001 - 009: select a prole between 001 and 009 when watching 3D content with 3D shutter glasses. Prole
001 is recommended when using Dreamvision’s active 3D glasses.
b) 010 to 255: select the best compensation prole depending on your screen and environment.
12.7 Installation Style
Flip the image to the left or right, up or down according to the projection state of the projector:
Front, Ceiling Mount (F), Rear or Rear Ceiling mount (R)
12.8 Keystone
Compensate for trapezoidal distortion caused by installation. Independently to the screen orientation, make sure
that the projector is not tilt more than 5% up/down. This setting cannot be used if “Pincushion” is set.
• Vertical Keystone from -16 to +16.
12.9 Pincushion
Corrects the geometric distortion that occurs when projecting on a curved screen. Pincushion can be set to from
0 up to 16 (more correction). This function cannot be used if “Keystone” is set
12.10 Aspect
When watching a movie or video program, you can manually set the desired aspect ratio to ll your screen. Select
the correct aspect ratio depending on your source:
• Zoom: Magnies the input image until it lls the screen horizontally. Part of the image may be outside of the
screen and not displayed.
• Auto: Magnies the input image and maintaining its aspect ratio until it lls the screen horizontally or vertically
whichever comes rst.
• Native: Displays the image at 4 times its original resolution at the center of the screen. Any source with
resolution above 1080p (1920x1080p and 2048x1080p excluded) will be shown without any scaling.
R699900 - Eos Series User Manual 31
Page 32
DISpLAY SETUp
13.0 DISPLAY SETUP
Back Color
Congures the screen color displayed when there is no active input. Set to Blue or Black.
Menu Position
Upper left, Upper right, Center, Lower right, Lower left.
Signal Display
On: Display the source of the input signals after input selection. Off: Don’t display.
Logo
On: Display D-ILA logo during startup for 5 seconds. Off: Don’t display.
Language
Choose the OSD language between: English, Japanese, German, Spanish, Italian, French, Portuguese, Dutch,
Swedish, Norwegian, Russian, Chinese or traditional Chinese.
14.0 FUNCTION
14.1 Trigger
The 12V trigger output can be used to control any compatible devices such as motorized screens or anamorphic
kits: The 12V trigger output is 12Vcc, 100mA. Select the trigger output behavior:
• Off: 12V trigger voltage state is always low.
• Power: 12V trigger state is high when the projector is powered ON. To be used with motorized screens.
• Anamo.: 12V trigger is high only when Anamorphic Mode A, B or C is engaged. To be used with motorized
anamorphic kits.
• Inst. Mode 1 up to 10: 12V trigger state is high when the selected Installation Mode is the same as the Mode
number congured.
14.2 O-Timer
You can congure this automatic power Off function that will switch off the projector when there is no operation
or after a determined timer. Choose the duration of the timer between: Off, 1 hour, 2 hours, 3 hours and 4 hours.
14.3 ECO Mode
This setting when set to On will minimizes the power consumption in the Standby Mode. Additionally, it will
automatically switch Off this unit whenever the input signal is interrupted for 20 minutes.
If you plan to control this unit using RS232 or LAN protocols, set the ECO Mode to Off.
14.4 Network
When the Communication Terminal selected is LAN, this unit will be visible on the local Network and the following
parameters need to be congured. Refer to section “18.2 LAN protocol”, page 41 for more details.
Control 4 Simple Device Discovery Protocol (SDDP)
Set to “On” to allow Control 4 SDDP to detect this unit. When this unit is not connected to a Control 4 environment
you can leave this setting to “Off”.
14.5 Remote Code A or B
Select in the projector menu the code A or B according to the code selected on the RCU. You can change
the code used by the RCU to communicate with the projector from A to B. To do so, press and hold for 3 sec
32
R699900 - Eos Series User Manual
Page 33
INFORMATION MENU
simultaneously [MENU]+[BACK] buttons on the RCU. All the buttons on the RCU will blink.
• Two blinks indicate that the RCU uses code B.
• Three blinks indicate that the RCU uses code A.
If the Remote Control Unit (RCU) code differs from the projector remote code setting, then the Standby /
On LED indicator will blink green when receiving the remote control orders.
14.6 High Altitude Mode
Set High Altitude Mode to “On” when using this unit at a place with a low atmospheric pressure or located at
an altitude of 900 meters (3,000 ft) above sea level or higher. This will improve the fan efciency and help in
preventing the projector to overheat.
14.7 Lamp Reset
Resets the lamp use time to “0” during the lamp replacement procedure. See Section “Resetting Lamp Time”,
page 37 for more details.
14.8 Factory Reset
Conrm to reset all this unit settings to default settings at once except the settings stored in memory below:
• Gamma Data saved into Gamma => Correction Value => Import
• Color Prole Data saved into Color Prole => Custom 1 up to Custom 6
14.9 Software Update
Conrm to start the update procedure. Make sure that a valid software le must be loaded on an USB stick and
that this stick is fully inserted in the USB/Update input located at the rear of this unit.
15.0 INFORMATION MENU
Input Terminal and Input Source
Displays the active video input and the type of the current video input signal.
Resolution and H. and V. Frequency
If the active input is PC input, its resolution, Horizontal and Vertical frequencies are displayed.
Color Depth / Color Space
Displays the color bit depth of the input video signal. N.A. with YCbCr (4:2:2) input.
Colorimetry
Displays the color space and color depth of the input signal. Also detects HDR color encoding like BT.2020.
HDR
Displays the EOTF information when HDR packet is received.
MaxCLL and MaxFALL
When explicitly present in the source meta data container, it displays the levels in nits of the brightest pixel of the
stream (MaxCLL) and the level of the brightest frame of the stream, MaxFALL.
Lamp Time
Displays the accumulated hours of usage of the lamp.
Soft Version
Displays the current software version.
Calibrator
Stores up to 18 ASCII characters set by the Calibrator. Shown only if set during ISF prole adjustment.
R699900 - Eos Series User Manual 33
Page 34
CINEMASCOpE SETUpS
16.0 CINEMASCOPE SETUPS
The Eos Series centralizes the controls and automation commands for a unique, versatile and unexpectedly
simple to operate 2.35:1 theatre experience using Lens Zoom or the Static Cinemascope kit.
• Up to 10 lens position memories
• Integrated Constant Image Width (CIW) scaling algorithm with anamorphic mode A and mode B.
• New scaling mode that is optimized for the full native 4096 x 2160 (17 x 9) resolution of the LCoS panels.
• Dedicated commands to control the picture sizes and aspect ratios on a 2.35:1 screen.
16.1 Cinemascope setup with Lens Zoom
Select “Menu => Installation => Lens Memory 1”
Zoom in, until the left and right borders of the picture ts the 2.35:1 screen borders. Save the lens position in the
lens memory 1. You can also edit the memory 1 name to “Cinemascope”.
Select “Menu => Installation => Lens memory 2”
Make sure to project a 16:9 picture, zoom out until the picture top and bottom t the top and bottom of the screen.
Adjust the focus and offset if required, then save this position into the memory 2. You can additionally edit the
memory name to “Standard AR”.
Switch format using the Remote Control Unit.
You can now switch between Cinemascope and standard formats easily by using the Setting Memory buttons on
the RCU and selecting the correct lens memory according to the source format.
Because of the nature of the lens motorization, the precision overtime is not enough to perpetually
maintain the correct zoom / focus / position after several zoom in and out. It is required to periodically
alter the lens setting.
16.2 Installing a 2.35:1 screen with the Static Cinemascope kit
At rst, you must install the screen and the anamorphic lens according to their respective installation instructions.
Video source is 16:9: set [Anamo]rphic to Mode B
When you select a 16:9 input and that you must see all the details on the picture, in particular the top and bottom
parts of the image, then you should choose the anamorphic Mode B. This aspect compress the picture vertically
so it can be fully displayed in a 2.35:1 screen.
“Menu => Installation => Anamorphic => Mode B”
Video source is Cinemascope: set [Anamo]rphic to Mode A
To obtain a Cinemascope picture into a 2.35:1 screen you must select anamorphic Mode A. Select Anamorphic
mode A for this input in the “Menu => Installation => Anamorphic => Mode A”.
[Anamo]rphic modes
OFF Anamo Mode A Anamo Mode B
When you press sequentially the [Anamo]rphic button, you change the mode from OFF, Mode A and Mode B.
• Mode A is intended to be used with an anamorphic lens to watch 2.35:1 content on a 2.35:1 screen.
• Mode B is intended to be used to watch 16:9 content on a 2.35:1 screen with the Static Cinemascope kit.
34
R699900 - Eos Series User Manual
Page 35
MAINTENANCE
Anamo Kit installed
2.35 screen
16:9 on 2.35 screen
2.35 on 2.35 screen Mode A
When the source switches format....
... press [Anamo] button to obtain the correct anamorphic mode.
Mode B
Mode A
Mode B
16:9 format
2.35:1 format
17.0 MAINTENANCE
17.1 Cleaning and Replacing the Dust Filter
The lter must be cleaned regularly to allow an efcient air intake. Otherwise, dirt may enter the unit and appear
on the screen, preventing you from enjoying the video fully. If dirt has entered the unit or if you need information
about the lter, please consult your authorized dealer. A lter cleaning warning appears every 500 hours.
Cleaning procedure
• Pull out the power plug from the outlet while the projector is in standby mode.
• Push down and pull the claws located on the rear trap that protect the dust lter, pull out the trap.
• Pull out the sponge dust lter
• Clean the lter with a vacuum cleaner
• Then Insert it back in its original position and make sure that the claws of the trap are rmly inserted.
Dust Filter
Rear trap
R699900 - Eos Series User Manual 35
Page 36
MAINTENANCE
17.2 Dirt on the Lens
The lens shall be cleaned using commercial blowers or lens cleaning papers (for cleaning glasses and cameras).
Do not use uid-type cleaning agents. This may lead to peeling of the surface coating lm. The lens surface is
fragile. Avoid rubbing it hard or knocking.
17.3 Replacing the Lamp
Light-source Lamp and Lamp Usage Time
The life of light-source lamps used for this unit is about 4500 hours when running this unit in low lamp power
mode.
• When the lamp power is set to Low, the lamp life is approximately 4500 hours. This average lamp life is not
guaranteed and may not reach 4500 hours depending on the operating conditions. Get ready or replace with
a new lamp when the accumulated usage time exceeds 4500 hours. Depending on the operating conditions,
the lamp may have to be exchanged earlier. If the image is dark or if the color tone is abnormal, replace the
lamp as soon as possible.
• When the lamp life time exceeds 2900 hours, a warning message is displayed, press the [BACK] button to
clear it and replace the lamp before the lifetime reaches 4500 hours.
ABOUT LAMP REPLACEMENT
If this unit is installed in a constricted place, attempting to replace the lamp in that place may cause injury.
Use only genuine replacement parts for the lamp unit. Otherwise, malfunction may occur.
Do not replace the lamp immediately after this unit has been used. The temperature of the lamp is still
high and this may cause a burn. Allow a cooling period of 1 hour or more before replacement.
Before replacing the lamp unit, pull out the power plug from the outlet and wait until the STANDBY/ON
led is still light red.
Procedure for Lamp Replacement
During the lamp replacement process, you may have access to sensitive parts of the projector.
• Loosen the screw on the lamp trap at the rear of this unit.
• Open the lamp Trap/ Cover by loosening the screw
• Loosen the 2 screws on the lamp unit to release it.
36
R699900 - Eos Series User Manual
Page 37
• Pull out the lamp unit using the handles.
• Insert the new lamp unit until it is rmly in place.
• Tighten the screws of the lamp unit.
• Attach the lamp cover and fasten the lamp trap screw.
Resetting Lamp Time
•Resetting the Lamp Time during playback
After installing a new lamp, reset the lamp time using the OSD menu
a) Turn On the unit.
b) Browse into the menu Function => Lamp Reset => Conrm.
c) Conrm time reset.
MAINTENANCE
•Resetting the lamp during Standby Mode with the remote control
After installing a new lamp, make sure that this unit is in standby mode.
a) Press 1 second sequentially the buttons [BACK], [OK], [HIDE]
b) Press 2 seconds the arrow button [DOWN]
The procedure is successful if the Light and Standby/On indicator LEDs blink alternately for three seconds.
CAUTION FOR THE LAMP RESET PROCEDURE
Reset the lamp time only when you have replaced the lamp.
Never reset it when the lamp is still in use. Otherwise, the approximate standard for gauging replacement
time may be inaccurate, lamp performance may deteriorate and lamp blowout may occur.
R699900 - Eos Series User Manual 37
Page 38
MAINTENANCE
STANDBY/ON
17.4 Blinking LEDs and Troubleshooting
When the projector is running for more than 1 minute, the Standby/ON LED will automatically switch
OFF.
Operating LED Description
WARNING
(orange/red)
- - red Unit is in standby mode.
- - green Unit is in operate mode.
- - blinking green
- - blinking red Unit is in cool down mode (switching off).
- orange -
continuous
red
blinking
orange
blinking red
LIGHT
(orange)
blinking
orange
- -
blinking
orange
STANDBY/ON
(green or red)
-
-
Unit is in operate mode but HIDE is ON. Press again the HIDE
button to obtain a picture.
Lamp time has reached 2900 hours, prepare to replace the
lamp soon. If used in low power mode, replace the lamp before
4500 hours.
blinks 1 time: The lamp failed to ignite, restart the projector
blinks 2 times: Lamp has shut down during projection.
blinks 3 times: Lamp cover is open. Check that cover is closed..
blinks 2 times: Cooling fans stop.
blinks 3 times: Internal temp is too high.
blinks 4 times: External temperature is too high.
blinks 1 time: DD board circuit failed.
blinks 2 times: Motor board circuit failed.
blinks 3 times: CPU board circuit failed.
blinks 4 times: Power board failed.
(green/red LED)
LIGHT (orange LED)
WARNING
(orange/red LED)
38
CAUTION: When in Cool Down mode, do not pull out the plug from the outlet. Also, do not block the air
inlets/exhaust vents by standing the projector on its end or laying it on its side.
R699900 - Eos Series User Manual
Page 39
MISCELLANEOUS
18.0 MISCELLANEOUS
18.1 RS-232C protocol
Serial communication specifications
Control of this unit is possible using a computer or automation device connected with a RS-232 cross cable
(female - female D-sub 9 pins cable) or LAN/ RJ-45 cable. Communication specications for this unit are as
follows:
Baud Rate 19200 bps
Data Format Binary
Mode Asynchronous
Parity None
Start Bit 1 bit set to high
Stop Bit 1 bit set to low
X on/off None
Flow Control None
RS-232C pin assignation
Pin Signal Function Signal Direction
2 RxD receive data PC -> Projector
3 TxD transmit data Projector -> PC
5 GND ground -
1, 4, 6-9 NC - -
1
6
9
Command Format
Header Command Command Data End of Data
21h 89h 01h 2 - 4 bytes variable 0Ah
Header : 21h 89h 01h for operating commands or 3Fh 89h 01h for reference command.
Command: from 2 to 4 bytes length
Command Data: variable length
End of Data xed to 0Ah
Operating commands
Here is a non exhaustive operating commands list.
Function Command Command Data Description
Connection check 00h 00h none Check the connection in standby mode
Power 50h 57h 30h / 31h Switch Off (Standby mode) / On.
Inputs 49h 50h 36h / 37h Switch active input to HDMI1 / HDMI2
Power /w conrm 52h 43h 37h 33h 30h 35h Switch this unit On.
37h 33h 30h 36h Switch this unit Off. (send twice)
Switch input 52h 43h 37h 33h 30h 38h Switch to next input
37h 33h 37h 30h Switch input to HDMI1
37h 33h 37h 31h Switch input to HDMI2
Keypad 52h 43h 37h 33h 30h 31h UP
37h 33h 30h 32h DOWN
37h 33h 30h 33h BACK
37h 33h 32h 45h MENU
37h 33h 32h 46h OK
37h 33h 33h 34h RIGHT
37h 33h 33h 36h LEFT
5
R699900 - Eos Series User Manual 39
Page 40
MISCELLANEOUS
Function Command Command Data Description
Hide Display 52h 43h 37h 33h 31h 44h Toggle Hide On/Off
37h 33h 44h 30h Switch Hide to On
37h 33h 44h 31h Switch Hide to Off
Picture Modes 52h 43h 37h 33h 36h 38h Cinema Mode
37h 33h 36h 39h Film Mode
37h 33h 36h 41h Natural Mode
37h 33h 45h 44h HDR10 Mode
37h 33h 45h 45h HLG Mode
37h 33h 36h 43h USER 1 Mode
37h 33h 36h 44h USER 2 Mode
37h 33h 36h 45h USER 3 Mode
37h 33h 36h 46h THX Mode
37h 33h 43h 41h USER 4 Mode
37h 33h 43h 42h USER 5 Mode
37h 33h 43h 43h USER 6 Mode
37h 33h 45h 34h Toggle picture mode
Low Latency 52h 43h 37h 33h 46h 38h Toggle Latency Mode value
Installation Memory 52h 43h 37h 33h 44h 38h Installation Memory 1
37h 33h 44h 39h Installation Memory 2
37h 33h 44h 41h Installation Memory 3
37h 33h 45h 35h Installation Memory 4
37h 33h 45h 36h Installation Memory 5
37h 33h 45h 37h Installation Memory 6
37h 33h 45h 38h Installation Memory 7
37h 33h 45h 39h Installation Memory 8
37h 33h 45h 41h Installation Memory 9
37h 33h 45h 42h Installation Memory 10
Expert Calibration
(ISF)
Expert Calibration
(THX)
Anamo 52h 43h 37h 33h 43h 35h Toggles the Anamorphic mode
Lens Control menu 52h 43h 37h 33h 33h 30h Toggle the lens control menu
MPC menu 52h 43h 37h 33h 45h 30h Toggle the MPC menu
CMD menu 52h 43h 37h 33h 38h 41h Toggle the CMD menu
52h 43h 37h 33h 35h 38h ISF - On and Adjust
37h 33h 35h 41h ISF - Off
37h 33h 35h 42h ISF - On locked
37h 33h 36h 34h Switch Picture Mode to ISF - Day
37h 33h 36h 35h Switch Picture Mode to ISF - Night
52h 43h 37h 33h 43h 36h THX plus - On and Adjust
37h 33h 43h 37h THX plus - Off
37h 33h 43h 38h THX plus - On locked
37h 33h 38h 35h Switch Picture Mode to THX - Bright
37h 33h 38h 36h Switch Picture Mode to THX - Dark
37h 33h 32h 33h Switch Anamorphic mode to A
37h 33h 32h 34h Switch Anamorphic mode to Off
37h 33h 32h 42h Switch Anamorphic mode to B
37h 33h 32h 43h Switch Anamorphic mode to C
40
R699900 - Eos Series User Manual
Page 41
MISCELLANEOUS
Projector
`Control Device
Examples
You want to... Command to send
Switch this unit On send: 21h 89h 01h 50h 57h 31h 0Ah
receive: 06h 89h 01h 50h 57h 0Ah
Switch this unit Off send: 21h 89h 01h 50h 57h 30h 0Ah
receive: 06h 89h 01h 50h 57h 0Ah
Change active Inpu PJACK t to
HDMI2.
Change Picture Mode to match HDR send: 21h 89h 01h 52h 43h 37h 33h 45h 44h 0Ah
send: 21h 89h 01h 52h 43h 37h 33h 37h 31h 0Ah
receive: 06h 89h 01h 52h 43h 0Ah
receive: 06h 89h 01h 52h 43h 0Ah
18.2 LAN protocol
Sending a LAN Control Command
In order to send a Remote Control compatible command to this unit, you must open a TCP connection on port
20554. The com port will stay opened until a PJREQ command is sent. This unit will conrm with PJACK, then
send immediately the commands because the connection will be dropped after 60 sec of inactivity. If for any
reason you have to change the TCP connection port, you may use the following RS-232c/LAN command.
[4Ch 53 50h 54h] + 4 ASCII chars as new port address in hexa
You want to set TCP port to 10000 Command to send
Send 10000 as new TCP port value:
10000 is 2710h in hexa, converted in
ASCII characters: 32h 37h 31h 30h
Then, reboot Network module send: 21h 89h 01h 4Ch 53h 52h 53h 0Ah
1. Opening Connection
on port 20554
3. Command Type
(PJREQ)
5. Send Commands
within 60 sec
after 60 sec of inactivity
connection is closed
send: 21h 89h 01h 4Ch 53h 50h 54h 32h 37h 31h 30h 0Ah
receive: 06h 89h 01h 4Ch 53h 0Ah
receive: 06h 89h 01h 4Ch 53h 0Ah
2. Projector Ready
(PJ_OK) no time out
4. Projector Acknowledge
(PJACK)
6. Projector conrms
the commands
LAN communication protocol and timed out
R699900 - Eos Series User Manual 41
Page 42
MISCELLANEOUS
Examples
You want to... Command to send
Switch this unit On 1. open TCP connection
2. receive PJ_OK: 50h 4Ah 5Fh 4Fh 4Bh
3. send PJREQ: 50h 4Ah 52h 45h 51h
4. receive PJACK: 50h 4Ah 41h 43h 4Bh
5. send Power On cmd: 21h 89h 01h 50h 57h 31h 0Ah
6. receive conrmation: 06h 89h 01h 50h 57h 0Ah
after 60 sec, TCP connection is closed.
Switch Anamorphic to mode A 1. open TCP connection
2. receive PJ_OK: 50h 4Ah 5Fh 4Fh 4Bh
3. send PJREQ: 50h 4Ah 52h 45h 51h
4. receive PJACK: 50h 4Ah 41h 43h 4Bh
5. send Anamorphic A:
21h 89h 01h 52h 43h 37h 33h 32h 33h 0Ah
6. receive conrmation: 06h 89h 01h 52h 43h 0Ah
after 60 sec, TCP connection is closed.
18.3 Infra Red, long hex-pronto compatible RCU
The infrared command must be sent using NEC 5 protocol in ASCII format.
In the following example, Power ON command is 37h 33h 30h 35h, this command has to be converted as ASCII,
it becomes 73 05.
To send this command using long hex Pronto compatible, convert the ASCII code as two hexadecimal numbers
as follow:
Code A: 73h = 115 (for code B: 63h = 99, replace 115 by 99)
05h = 5
Then program the Pronto RCU using the Device number 115 and Function 5:
Device Code: 115 (0x73) Function: 5 (0x05):
0000 006D 0001 0011 0141 00A0 0014 003C 0014 003C 0014 0014 0014 0014 0014 003C 0014 003C 0014
003C 0014 0014 0014 003C 0014 0014 0014 003C 0014 0014 0014 0014 0014 0014 0014 0014 0014 0014
0014 0336
A complete device/function chart with their corresponding long hex commands is available, ask your dealer if
required.
42
R699900 - Eos Series User Manual
Page 43
18.4 Specications
The Eos Series uses the latest 4K panels developed to provide the most exciting video-projection experience
ever.
Model Eos 1 and Eos 2 Eos Signature
Emission method LCoS (Reective Active Matrix Principle)
Display panel size 0.69” LCoS 4K panels
Display Resolution 4096 x 2160 pixels (D-Cinema 4K format) 8192 x 4320 pixels
Contrast ratio 40,000:1 for Eos 1. 80,000:1 for Eos 2 100,000:1 for Eos Signature
High Contrast ratio 400,000:1, 800,000:1 1,000,000:1
Projection lens 65 mm diameter Std Quality Lens
Throw ratio 1.4:1 - 2.8:1 with 2x Zoom
Electronic zoom, focus and shift:
80% vertically and 34% horizontally
Installation Memories 10 slots lens zoom/focus/position/aspect ratios/convergence and masking
Brightness 1800 , 1900 ANSI Lumens 2200 ANSI Lumens
Screen size 60” to 200” (Aspect ratio 16:9) 60” to 280” (Aspect ratio 16:9)
Distance range from 1,5 m to 12 m
Inputs:
HDMI 1 input HDMI 2.0b with HDCP2.2 - Ultra HD BluRay compatible with 4K and HDR
HDMI 2 input HDMI 2.0b with HDCP2.2 - Ultra HD BluRay compatible with 4K and HDR
LAN RJ-45 for Control
RS-232 D-Sub 9-pin (male) Serial Com port for Control
USB Type A Firmware updates and service only.
12V Trigger DC power Jack 3.5 mm. 12V @ 100 mA
Color Gamuts REC.709 gamut for Eos 1 and beyond DCI-P3 gamut for other models
Video Processing Auto Tone Mapping for HDR10 contents. HDR Picture modes with Perceptual
Quantization (PQ) EOTF and Hybrid Log gamma. HDR colorimetry and MaxCLL /
MaxFALL meta-data auto-detect. High quality Low Latency processing optimized
for real time simulations and gaming. Advanced blur reduction and enhanced 400
Hz Crystal Motion®.
Light source lamp 265W NSH - up to 4 500 hours with lamp used in low mode
Power Requirements 100V - 240V AC 50Hz/60Hz
Power Consumption <400W (0.3W in standby and eco mode)
Unit size (W x H x D) 50 x 26 x 49.5 cm - 19.7" x 10.1" x 19.5"
(Height 28 cm with feet)
Net Weight 26 kg - 57.3 lbs
Box size (L x W x H) 66 x 65 x 44 cm - 26.0" x 25.6" x 17.3"
Gross Weight 30 kg - 66.1 lbs
Operation Environment Temperature: 5°C to 35°C (Storage Temperature: -10°C to 60°C)
Humidity: 20% to 80% without condensation
• Design and specications are subject to change without prior notice.
• Please note that some of the pictures and illustrations may have been abridged, enlarged or contextualized
in order to aid comprehension. Images may differ from the actual product.
100 mm diameter High Quality Lens
Throw ratio 1.4:1 - 2.8:1 with 2x Zoom
Electronic zoom, focus and shift:
100% vertically and 43% horizontally.
50 x 26 x 52 cm - 19.7" x 10.1" x 20.4"
(Height 28 cm with feet)
3-CHIP LCOS SYSTEM
LCoS is the abbreviation of Liquid Crystal on Silicon. The 3-Chip LCoS systems feature dedicated panels
for each color channel and render seamless color graduations without any ickering or rainbow effect
artifacts
Page 44
18.5 Dimensions
Eos 1 & Eos 2 models Eos Signature model
26 cm
10.1”
2 cm
0.79”
52 cm
20.4”
50 cm
19.7”
50 cm
19.7”
52 cm
20.4”
Page 45
Page 46
Page 47
Page 48
Loading...