DreamWeaver II
ENGLISH
Dear Customers,
Thanks a lot for choosing the DreamWeaver II digital Cinema Projector, Wide PAL
(576 x 1024) version of the DreamWeaver
Yo u will find in the following document the small modification that differentiate the
Weaver II from its «big brother» DreamWeaver.
If you have any further question, do not hesitate to contact either your local distributor, getting its contact details on our website : www.dreamvision.net
Or send us a mail to info@dreamvision.net
Original pages that have been modified:
Page 3
Page 5
Page 9
Page 12
Page 13
Page 14
Page 19
Page 21
Page 22
Page 24
Page 25
Page 26
Page 27
Page 30
Page 33
Page 34.
1
Modification of the Page 3 of the user’s Guide
Introduction
First of all, we would like to thank you for chosing a DreamVision
Cinema Projector. Your new DreamWeaver II projector from DreamVision
is specifically designed for home cinema applications. The DreamWeaver II
sets the standard for enhanced-definition digital perfection, featuring
enhanced Definition 1024x576 resolution using the latest DLP™ technology
and new DCDi video processing from Faroudja™. Calibrated to D65 color
mastering standards, the DreamWeaver II reproduces colors and details the
way the director intended. Whether you are watching movies or High Definition broadcasts, you will enjoy breathtaking image quality.
Included items
projector
remote control
and baterries
®
Home
®
Projector components and features
remote
control
receiver (IR)
air intake
vent
I/O panel
under the top cabinet
Remote Receiver
Under the top cabinet
leveling
foot
focus
heat vent
zoom
keypad
(under the top
cabinet)
IR
elevator foot release
IR
exhaust
lens cap
power
cable
user’s guide
2
Modification of the Page 5 of the user’s Guide
Positioning the projector
There are a number a factors to consider when determining where to set up
the projector, including the size and shape of your screen, the location of
your power outlets, and the distance between the projector and the rest of
your equipment. Here are some general guidelines.
Position the projector on a flat surface at a right angle to the screen.
1
The projector must be within 10 feet (3 m) of your power source. To
ensure adequate cable access, place the projector at least 6 inches
(0.15m) from a wall or other objects. Place the projector at least 5.6 feet
(1.7 m) from the projection screen.
If you install the projector on the ceiling, refer to the installation guide
that comes with the Ceiling Mount Kit for more information. To turn
the image upside down, see page 14. DreamVision recommends use of
an authorized DreamVision ceiling mount. The Ceiling Mount Kit is
sold separately, see page 11.
10’ high
image
2
Position the projector the desired distance from the screen.
The distance from the lens of the projector to the screen, the zoom setting, and the video format determine the size of the projected image.
For more information about projected image sizes, see page 12.
The image exits the projector at a given angle. This image offset is 133%.
This means that if you have an image 10’ high, the bottom of the image will
be 3.3’ above the center of the lens.
Check Page 34 for further help.
bottom of image
3.3’ above lens
3
lens center
Modification of the Page 9, 12, 13, 14, 21, 22 of the user’s Guide
Both Menu «Picture» and «Advanced» have been slightly modified for an
optimised ease of use.
So the typical window of the Picture Menu is now:
The typical window of the Advanced Menu is now:
New Picture Menu Window
New Advanced Menu Window
4
cation of the page 19 of the User’s Guide
Modifi
Using the remote control
The remote uses two (2) provided batteries. They are easily installed by sliding the cover off the remote’s back, aligning the + and - ends of the batteries,
sliding them into place, and then replacing the cover.
To operate, point the remote at the projection screen or at the projector (not
at the video device). The optimum operation range is 0 to 30 feet (9.14m)
Press the remote’s
the
arrow
buttons to navigate, and the
adjust values in the menus. See page 21 for more info on the menus.
The remote also has:
Power On
Brightness + / -, contrast + / -
Blank
page 29)
Source 1, 2, 3, 4
source to a source button, see page 28)
Source select
Native, 16:9, 4:3, Letterbox
Resize
Auto image
Preset
Overscan
Freeze
Key +
and
button to display a blank screen instead of the current image (see also
button to change the Aspect Ration (See also page 22)
button to restaure stored settings (see page 24)
button to remove noise in a video image (page 24)
button, to freeze the displayed picture.
and
Key -
Menu
button to open the projector’s menu system. Use
Select
button to select features and
Power Off
buttons to switch among sources (to assign a particalur
button which is a source toggle.
button to resynch the projector to the source
buttons to adjust the keystone.
buttons (see page 11 for shut down info)
buttons to adjust the image
to have direct access to the main aspect ratio
5
cation of the page 24 of the User’s Guide
Modifi
Presets
: This allows you to customize settings and save the settings to be
restored later. To restore the factory default settings, choose Factory Reset in
the
Settings>Service
To set a preset for the current source, adjust the image, select
menu.
Save Settings
in the Presets menu, then choose Save User 1, 2, or 3. You can recall these
settings in the future by selecting the appropriate user presets.
Gamma
: gamma tables contain preset intensity configurations optimized
for the input source. You can select a gamma table that has been specifically
tuned for either film, video, Bright Room, or PC input. (Film input is material originally captured on a film camera, like a movie; video input is material originally ccaptured on a video camera, like a TV show or sporting
event.) White Peaking inccreases the brightness of whites that are near
100%.
NOTE:
Your viewing preferences may vary. Cycle through the gamma
options and pick the one you like the best.
Overscan
: Lets you crop the input or zoom the input if desired.
Presets
Save User Presets
Gamma
Overscan
6
cation of the page 25 of the User’s Guide
Modifi
Advanced settings
The following 4 options are for commputer of HDTV sources only
Phase: adjust the phase of the video signal’s digital conversion.
Tracking : Adjust the frequency of the video signal’s digital conversion.
Horizontal / Vertical position : Adjust the position of the source.
TrueLife : This option refers to Faroudja’s TrueLife processing of the image.
All standard definition interlaced video signals (composite, S-video and
component) are routed through this processor. Extended and High Definition progressive component sources are not routed though this processor by
default. You can turn TrueLife on to route these signals through the processor and then adjust the following 3 options:
Chroma Detail
Luma Detail
Chroma Delay :
CCS
: (Cross Color Suppression) processes the signal to remove any color
information from the luma portion of the signal. It is On for all composite
signals, Off for all component signals, and can be turned on or off for all
S-video signals.
Film Mode
lacer attempt to perform 3:2 pulldown, assuming the source was originally
created on 24fps film. If the original source is 30fps film, you should select
NTSC 2/2 pulldown.
Noise Reduction
noise reduction, choose Auto to have the software determine the amount of
noise reduction, or choose Manual and adjust the Level.
Skintone Bypass
applied to skin tones. Images of people often look better with less processing. Available when Auto or Manual are selected.
: This adjusts the color sharpness.
: This adjusts the sharpness.
aligns the Luma and Chroma Detail
: controls deinterlacing. 2:2/3:2 Enable If selected, the deinter-
: adjusts signal noise reduction. Choose Off to have no
prevents the noise reduction processing from being
Advanced
True Life
Film Mode
Noise reduction
7
cation of the page 26 of the User’s Guide
Modifi
Color Space
: This option applies to computer and HDTV sources (it won’t
appear in the menu for video sources). It allows you to select a color space
that has been specifically tuned for the video input. When Auto is selected,
the projector automatically determines the standard. To choose a different
setting, turn off Auto, then choose RGB for computer sources, choose
REC709 for component 1080i or 720p sources, or choose REC601 for component 480p or 576p sources.
Color Space
Color Temperature
: changes the intensity of the colors. Select a listed
value.
Color Control
: allows you to individually adjust the gain (relative warmth
of the color) and the offset (the amount of black in the color) of the red,
green, and blue colors.
Video Standard
: When it is set to Auto, the projector attempts to pick the
video standard automatically based on the input signal it receives. (The
video standard options may vary depending on your region of the world.)
If the projector is unable to detect the correct standard, the colors may not
look right or the image may appear “torn.” If this happens, manually select
a video standard by selecting NTSC, PAL, or SECAM from the Video Standard menu.
Color Temperature
Color Control
Video Standard
8
Modification of the page 27 of the User’s Guide.
This page remains blank in the DreamWeaver II User’s Guide.
9
cation of the Page 30 of the User’s Guide
Modifi
Service
Factory Reset
to their default after displaying a confirmation dialog box.
Test Pattern
is pressed. To select the patterns, use the up/down arrows on the remote or
keypad.
: to use these features, highlight them and press
: restores all settings (except Lamp Hours, Ceiling, and Rear)
: displays a test pattern when the
Blank
button on the remote
Select
.
Service menu
Blue only
to properly adjust the color balance with a SMPTE color bar pattern.
Color Wheel Index
ADC calibration
color accuracy can be optimized. Adjust the slidebars for each value and
note the change in the appropriate color. Use a component input when
adjusting the component controls.
Service Code
: Tuns off the Red and Green portions of the input, allowing you
: Makes the hue of various gray levels consistent.
: allows adjustment of thee calibrated ADC values so that
: only used by authorized service personnel.
Maintenance
Cleaning the lens
Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
1
Avoid using an excessive amount of cleaner, and don’t apply the
cleaner directly to the lens. Abrasive cleaners, solvents or other harsh
chemicals might scratch the lens.
2
Lightly wipe the cleaning cloth over the lens in a circular motion. If you
don’t intend to use the projector immediately, replace the lens cap.
clean the lens
with a soft dry cloth
and non-abrasive
cleaner
10
cation of the page 33 of the User’s Guide
Modifi
Accessories
Appendix
Specification
Temperature Operating
Non-operating
Altitude Operating 0 to 2,286 meters (7,500 feet)
Non-operating 0 to 6,096 meters (20,000 feet)
Humidity Operating 10% to 95% relative humidity, non-condensing
Non-operating 10% to 90% relative humidity, non-condensing
Dimensions
Weight
Optics
Focus Range
Lamp Type
50 to 95
-4 to 158
Diameter: 439 mm - Height: 127 mm
4. 4 kg unpacked
1.5 - 10 meters (5 - 32.8 feet)
UHP lamp (dual watt: 200 and 250 watt)
F (10 to 35
°
°
F (-20 to 70
C) at 0 - 10,000 feet
°
°
C) at 0 -20,000 feet
Standard Accessories
(ship with the projector)
Shipping Box (with packaging)
Power Cable (country-dependent)
Remote (and batteries)
Projection Lamp Module (included in projector)
Lens Cap
User’s Guide
Optional Accessories
Projector Mount
Replacement Lamp Module
NOTE : Use only approved accessories.
Input Power Requirements
200V-240V 2A 50 Hz
100V-120V 4A, 50/60 Hz
11
cation of the Page 34 of the User’s Guide
Modifi
Red LED behavior and projector errors
If the projector is not functioning properly and the red LED is blinking, consult
Ta b le 2
between the blinking cycles.
Red LED Behavior Explanation
One (1) blink The lamp won't strike after five (5)
Three (3) blinks The projector has shut down the lamp.
Four (4) blinks The fan has failed. Replace the lamp (the
Five (5) blinks The projector is overheating. Check for a
to determine a possible cause. There are two second pauses
Ta b le 1: Red LEDs
attempts. Check the lamp and lamp door
installations for loose connections.
Turn off the projector, wait one minute,
then turn it back on. Replace the lamp.
Contact Technical Support for repair if
replacing the lamp does not solve the
problem.
lamp module contains a fan). Contact
Technical Support for repair if replacing
the fan does not solve the problem.
blocked air vent. Contact Technical Support for repair if clearing the air vents
does not solve the problem.
Projected image size
Range of projection distances for a given screen size
16:9 Screen
dimensions
(inches/m)
27x48
.69x1.22
34x60
.9x1.5
40.5x72
1.0/1.8
45x80
1.1x2.0
49x87
1.2/2.2
52X92
1.3X2.3
54X96
1.4X2.4
58X104
1.5X2.6
65X116
1.7X3
Screen
diagonal
(inches/m)
55.1/1.4 7.5/2.3 10.4/3.19
68.8/1.75 9.42/2.87 13.06/3.98
82.6/2.1 11.09/3.38 15.36/4.68
91.8/2.3 12.27/3.74 17.03/5.19
99.8/2.5 13.48/4.11 18.7/5.7
105.6/2.7 14.21/4.33 19.69/6.0
110.1/2.8 14.93/4.55 20.07/6.31
119.3/3.0 16.14/4.92 22.38/6.82
133.1/3.4 18.54/5.65 25.72/7.84
Ta b le 2:
Projection Distance
Maximum
zoom
(feet/m)
Minimum
zoom
(feet/m)
12
Loading...