DREAM ON ME INC.
125 HELEN STREET
STYLE NO: 683
PORTABLE CRIB
CAUTION :ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 23-5/8”
CONSUMER
PRODUCT
SAFETY
COMMISSION
S.PLAINFIELD NJ 07080
908-791-0555
STEP 1
Assemble latch (i & j) to the headboard (A & B)
by using 5/8” screw (k).Then assemble plastic
block(n) to the headboard ( A & B) by using 3/4”
screw (m).Tighten all by phillips-head screwdriver.
Make sure that the latch on the bottom of each
headboard ( A & B ) are locked.
m
n
m
B
A
MFG CODE :BLY
MFG DATE: APR 2013
STEP 2
Connect rail (C) and stabilizer bar (D)to the headboard ( A & B) by
screws (a) and nuts (b) , wood dowel (d) , washer (g) , washer (h) .
DO NOT fully tighten the bolts.
g
h
b
h
g
a
c
C
b
a
B
h
g
a
(600MM) BY 37-3/4” (959MM) WITH A THICKNESS NOT EXCEEDING 2” (51MM) .
THE CRIB CONFORMS TO APPLICABLE REGULATIONS PROMULGATED BY
MADE IN CHINA
STEP 3
Slot in the metal pin into the notch of left and right
headboard side corner post.then move up and down
to adjust the mattress base into medium or
highest level.
B
C
E
THE CONSUMER PRODUCTS SAFETY COMMISSION.
A
A: Left head board (1PC)
B: Right head board (1PC)
B
C: Rail (2Pcs)
D: Stabilizer bar (1PC)
e:
Castors (2 pcs)
a: 2-1/8” Allen head bolt
c:
2” Allen wrench (1 pc)
f: Castors (2 pcs)
CERTIFIED
AN INDEPENDENT TESTING
LABORATORY VALIDATES THE
MANUFACTURER’S CERTIFICATION
OF THIS CRIB TO ASTM F-406,
CPSC 16 CFR 1220
(10 pcs)
d: 1-1/2” Wood dowel (2 pcs)
g: Washer
b:Barrel nuts (10 pcs)
(10 pcs)
h: Washer
(10 pcs)
j
k
k
i
STEP 4
Connect rail (C) to the headboard ( A & B) by screws
(a) , nuts (b), washer (g) , washer (h) .
THEN FULLY tighten all the bolts .
k
A
C
E
B
b
h
g
g
A
h
D
b
d
b
a
g
h
b
h
g
a
a
STEP 5
Assemble castors (e&f ) to the leg bottoms on the leg on
headboard (A&B). 2 castors (e) with brake are in the front.
THEN add the mattress( F ).
a
B
C
F
A
D
STEP 6
Select the desire level,and use both hand to lift up
the mattress base,then adjust the level to your
require height of the 3 level.
B
C
m: 3/4”screw
(8 pcs)
WRENCH
FLAT HEAD SCREWDRIVERAND
WRENCH REQUIRED FOR
ASSEMBLY----NOT INCLUDED
E: Mattress board (1PC)
F: Mattress (1PC)
i: Latch 1 (2 pcs) j: Latch 2 (2 pcs)
FLAT HEAD SCREWDRIVER
n: Plastic block (4 pcs)
k: 5/8” screw
(6 pcs)
WARNING
****Keep instructions for future use****
. This product meets or exceeds specifications as issued by the consumer product safety for non-full size baby cribs.
. C aution: Before using this unit recheck all screws to be sure they are tightened securely. a periodic check should be
made of all screws&nuts to be sure they remain tight.
WARNING
C
g
b
h
b
a
g
h
a
Follow bellow to fold the crib:
1.take out the mattress (F)
2.take out the mattress board (E)
3.unlock the latch on the headboard
4.fold the crib
b
h
g
a
f
A
e
C
e
F
****Infants can suffocate****
A
C
. In gas between a mattress too small or too thick and product sides.
. On soft bedding never add a mattress, pillow,comforter,or padding.
. Use up and middle level mattress support only for a new born baby and not more than the first 3 months.
e
f
WARNING
. Failure to follow these warnings and the instructions could result in serious injury or death.
e
. Do not use plastic shipping bag or other plastic film as mattress covers not sold and intended for that purpose, they
can cause suffocation.
. Never use a watter mattress with this product, if refinishing,use a non-toxic finish specified for children’s products.
. Strings can cause strangulation! Never place items with a string around a child’s neck,such as hood strings or
pacifier cords.Never suspend strings over product or attach strings to toys.
. Discontinue use of the product when child is able to climb out or reaches the height of 35in.(890mm).
. When child is able to pull to standing position,set mattress/base to lowest adjustment position and remove bumper
pads, large toys ,and other objects that could serve as steps for climbing out.
. Never place product near window where cords from blinds or drapes can strangle a child.
①
②
①
②
. Always provide the supervision for continued safety of your child.
. To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their back to sleep, unless
otherwise advised by your physician.
. Never use this product if there are any loose or missing fasteners, loose joints,broken parts, or torn mesh/fabric.
check before assembly and periodically during use. Contact DREAM ON ME. for replacement parts and instructional
literature if needed.Make sure the latches are secure.
. Never substitute parts, the product including side rails, must be fully erected prior to use.
. Always provide the supervision necessary for the continued safty of your child. When used for
playing, never leave child unattached.
MADE IN CHINA
Loading...