DreamLine SHDR656076008, SHDR656076007, SHDR65600ENGIMATUB, SHDR656062007, SHDR654876007 User Manual

...

Page 1

ENIGMA SKY

SHOWER AND TUB DOOR INSTALLATION INSTRUCTIONS

IMPORTANT

DreamLine For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.com

reserves the right to alter, modify or redesign products at any time without prior notice.

MODEL #s

SHDR-6548760-## SHDR-6560760-##

Right-hand door installation shown

For more information about DreamLine

ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

Shower Doors, Tub Doors & Enclosures, please visit DreamLine.com

MODEL #s

SHDR-6560620-##

##=finish 07- Brushed Stainless Steel 08- Polished Stainless Steel

Page 2

This model is treated with DreamLine’s

exclusive ClearMax

Glass technology. This is a specially formulated coating that prevents the buildup of soap and water spots.

Install the surface with the ClearMaxTM label towards the inside of the shower. Please note that depending on the model, the glass may be coated on either one or both surfaces.

For best results, squeegee the glass after each use and dry with a soft cloth.

ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

Page 3

Table of Contents

Section title

Reinforcement

Troubleshooting and Maintenance tips

Preparation Tools

Detailed Diagram of Shower Door Components

Parts List

Installation Steps

Bumper Installation

Vinyl Seals

Product maintenance

Maintenance Checklist

Page #

7 8-26

22-23

OOR

ANEL

OOR

Right-hand door installation Left-hand door installation

NOTE: The right-hand door installation is shown as an example throughout this manual. For the left-hand door installation, simply

ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

begin on the opposite wall and reverse the orientation of the parts in the steps shown.

Page 4

Reinforcement for Enigma Series

Heavy Glass frameless sliding shower or tub door

Install studs OR install 2”x 6” wood blocking between the studs where the

Guide Rail Brackets will attach to the wall

Stud

measured

from threshold

or tub deck*

(see list below)

2” X 6”

threshold or tub deck

*Blocking height requirement (to center) as measured from threshold or tub deck: Enigma Air, Enigma Sky = 73” for shower ht / 59” for tub ht Enigma X, Enigma XO = 72-1/2“ for shower ht / 58-1/2” for tub ht Enigma Z = 73-1/2” for shower ht / 59-1/2“ for tub ht Enigma = 75-1/2” for shower ht only

ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018 2

threshold or tub deck

Page 5

ENIGMA-SKY

Right Hand door installation shown as an example

troubleshooting and maintenance tips

*Stopper properly positioned and tight

-door makes contact with stopper and bottom bumper evenly when the door is in the fully open position

Guide Rail bracket ush with wall and set screws tight

Guide Rail level

Glass brackets tight

The Roller wheels can be adjusted as needed so that door glass makes even contact within the u-channel from top to bottom

Roller Wheels tight leaving the proper clearance beneath the door glass and guide block

Bottom Roller Wheels adjusted to make contact with the Guide Rail

Rotate disk to adjust

*Stopper properly positioned and tight so that the Door stops against the stopper and seals rmly into the bumper inserts in the u-channel

Guide Rail bracket ush with wall and set screws tight; Installation into a stud strongly recommended

To secure the Stoppers (#05): Apply the Thread Lock adhesive to the threads of the set screws during the nal installation. Fully tighten the set screws with the supplied allen wrench.

Stopper

Panel Glass

Door Glass

Inspect bottom corners of door glass for damage. **Units with

SafeStop™ Bumper is secured in position with 3M tape or screwed to the wall

damaged door glass should not be used until door glass has been replaced**

Panel Glass sits ush on the threshold

Guide block screwed down and square with glass

All rubber gaskets and sleeves installed properly between all hardware and glass to prevent glass to metal contact

Handle tight

Bumper inserts installed into u-channel

Thread Lock Adhesive

* Stopper Locations as measured from the wall to the center of the stopper:

• Panel side: 5” (+/-) when the door contacts the bottom bumper

• Door side: 3-1/2” (+/-) (depends on opening conditions)

Recommend to apply thread lock to:

• Stopper set screws

• Wheel bolts

• Glass Bracket bolts

ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

Page 6

Preparation

1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece count with the packing slip. After opening all boxes and packages read this introduction carefully. Check that all of the necessary parts are included in the package by checking off the components on the “Detailed Diagram of Shower Door Components”. If the unit has been damaged, has a finishing defect, or has missing parts, please contact our customer support department within 3 business days of the delivery date. Please note that DreamLine® will not replace any damaged products or missing parts free of

charge after 3 business days or if the product has been installed. Contact DreamLine questions, and please provide an order number, job name or other proof of purchase to help identify the original order.

2. Please note that you should consult your local building codes with questions on installation

compliance standards. Building and plumbing codes may vary by location, and DreamLine® is not responsible for code compliance standards for your project and will not accept any returns.

3. If this unit is going to be installed in a new construction, please install all of the required plumbing and drainage before installing the shower. Use a competent and licensed (if required by local code) plumber for all plumbing installation

4. Please make sure that prior to beginning the installation, the surfaces are leveled and solid and will be able to support the total weight of the unit. Also make sure the walls are at right angles. Irregular installation surface level, radius corners or improper angle of side walls will result in serious problems for your installation. Note that some adjustments and drilling will be necessary during the installation process.

if you have any

5. Please protect all primary surfaces of the product during installation. Never set the glass down directly onto a tile floor. Leave corner protectors in place until necessary to remove them. Always use a piece of wood or cardboard to protect the bottom edge and corners of the glass prior to and during installation.

6. This unit must be installed upon a finished threshold and against finished walls.

7. This model does NOT have any adjustment for out-of-plumb wall conditions. Verify that your walls are

plumb before proceeding with the installation.

8. This model requires that you drill into the threshold for proper installation.

9. Installation of the Guide Rail brackets into a stud or 2” x 6“ wood reinforcement is strongly

recommended. See Steps #8 and #19 for details.

10. This model requires a minumum of 2-1/4” of flat threshold space for installation.

11. Professional installation required.

NOTE: This manual will describe the shower door installation. Please follow the same sequence of installation steps for the tub door installation.

NOTE: DO NOT attach the handle to the door glass until instructed. DO NOT use the handle to lift the glass during installation. This may result in damage to the

glass and/or serious injury. Always use an assistant and/or a professional grade glass suction cup when handling heavy glass panels.

4ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

Page 7

Level

Tape Measure

Tools

Pencil

Silicone

Carpenter’s Square

Drill bit

(Ø5/16") (8mm)

Phillips Screwdriver

Painter’s Tape

Drill bit (Ø1/8")

(3mm)

Metal File

Tip: Measure the finished opening before proceeding with the installation to be sure that the correct model size has been ordered.

Power Drill

1/2” Shims

Threshold must be level.

Soft Head Hammer

Professional-grade Glass suction cup

Top

Middle

Chop saw and Hacksaw

Tip: Prior to installation, cover the

Bottom

shower/tub drain with tape to prevent losing screws or small parts.

Tip: Set screw gun clutch to low setting

when installing screws and bolts to prevent stripping the heads.

NOTE: Unpack your unit carefully and inspect it. Lay it out and identify all parts using the detailed diagram and packing list in this manual as a reference. Before discarding the carton, check for small hardware bags that may have fallen to the bottom of the box. If any parts are damaged or missing, please contact DreamLine

for replacement. The shipping boxes may contain extra parts not used in

your model configuration.

NOTE: Retain these installation instructions for future reference.

5ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

Page 8

Detailed Diagram of shower door components

ANEL

OOR

The glass surface

with the ClearMax™

label must be

installed to face

inside of the shower

Right-hand door installation shown

6ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

Page 9

Parts List

ITEM #

PART NUMBER

62" 76"

4876" 6076" 6062"

4876" 6076"

6062" 48" 60"

07021109

07021111

07021112

07321023

07551068

04100011-0638

48"

04100011-0790

60"

07121138 07121089

010420001 010420003 010420005

0104200 010420012 010420011

07121075

07121074

07024109

07024111

07024112

07324023

07554068

/04100041-0638

/04100041-0790

/ 07124138 / 07124089

07124075

07124074

DESCRIPTION

U-channel

Stationary glass

Door glass

Guide Rail

Stopper

Guide Rail Bracket( 6a&6b)

Glass Bracket

Roller

Threshold End Cap

Anti-splash Threshold

QTY

1PC

2PCS

4PCS

1PC

07021110

063004100-1798

07221004 07224004

07550045

092111

091104

098004

160012

092113

07021153

62" 76"

07550074

07024110

07121137

07121069

07024153

/ 07124137

/ 07124069

Guide Block

Anti-water side strip

Handle

5/16" plastic wall anchor

Countersunk screw ST4.2X40

Round head

Allen wrench ( 4mm)

Thread Lock Adhesive

Countersunk screw ST4.2X55

Bumper

U-channel

Insert Bumper

screw ST4.2X25

1PC

2PCS

1set

11PC

9PC

1PC

2PCS

1PC

5PC

7ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

Page 10

Installation steps

1. Check both nished walls to make sure they

are plumb and check the threshold to make sure it is level across the opening. (Fig 1)

NOTE: This model does not allow for out-of-plumb or out-of-level adjustment.

NOTE: This model requires a minimum

2-1/4” of flat threshold space for installation.

Top

Middle

Bottom

2-1/4 "

Minimum flat threshold space required

2. Measure the finished opening width at the model height.

Use a Chop saw (with a blade for cutting stainless steel), to cut the Guide Rail (#04) to fit the finished opening.

(Cut from the door end of the rail only)

◾for Shower model: Measure the width at a height of 72-1/4” ◾for Tub model: Measure the width at a height of 58-1/4”

This will be dimension (W).

The Guide Rail (#04) is 1“ less than the model size and will need to be cut to 1” less than the finished opening size (W):

Fig 1

Finished opening (W) - 1” = finished cut length (L)

(Fig 2a and Fig 2b)

Fig 2a

8ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

Page 11

_____________ Model size

Finished opening (W) - 1” = finished cut length (L)

panel end

_____________ -(minus) Finished opening (W)

_____________ = Finished cut length (L)

NOTE: Use a metal file to remove any burrs from the cut end of the Guide Rail (#04).

Metal File

(L)

Cut from the door end only which

is the end opposite from the holes

Fig 2b

door end

3. Starting from the wall on the stationary panel side

of the finished opening, use a Carpenter’s Square as a guide and measure in 1/8” -1/4” from the outside of the threshold and mark the threshold. Extend this line across the threshold to the opposite wall to use for reference in Step #18. (Fig 3)

threshold

1/8”

to 1/4”

outside

Fig 3

9ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

Page 12

4. Align the edge of the U-Channel (for Panel Glass) (#01)

to the inside of the reference mark on the threshold. Use a level to hold the U-channel plumb and mark the position of the U-Channel (for Panel Glass) (#01) on the wall. Also mark the four holes for drilling through the pre-drilled holes in the U-channel. (Fig 4)

U-Channel

reference mark

Fig 4

5. Remove the U-Channel (for Panel Glass) (#01) from the wall, drill the anchor holes using a Ø5/16”

drill bit and insert the Ø5/16” Plastic Wall Anchors (#16) (**see Note below). Apply a bead of silicone to the back of the U-Channel (for Panel Glass) (#01) and attach it to the wall using four of the ST4.2 x 40 Round Head Screws (#17). (Fig 5)

2**

Ø1/4"

or Ø5/16"

3**

**NOTE: When installing to

a stud, drill a Ø1/4” hole and do not use the anchors.

Fig 5

10ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

Page 13

outside inside

plumb line

1-1/4”

Guide Rail Bracket

u-channel

U-Channel

Fig 6a

outside outside

1 1/4”

Guide Rail Bracket

58-1/4”

57-1/4”

(H)=

71-1/4”

1 1/4”

72-1/4”

(H)=

Fig 6b

Right-hand door installation shown as example

6. To position the Guide Rail Bracket (#06) on the

stationary panel side: From inside the shower, measure up from the threshold to the bottom of the Guide Rail Bracket (#06) using

Table 1 below. Hold the bracket in place 1-1/4” from the outside of the U-channel (as shown in Fig 6a) and mark

the wall at the bottom of the bracket.

(Fig 6a and Fig 6b and Fig 6c)

tub height

Fig 6c

shower height

GUIDE RAIL BRACKET HEIGHT

MODEL HEIGHT

shower

76"

tub

62"

H =

72-1/4" 58-1/4"

Table 1

11ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

Page 14

7. Hold the Guide Rail Bracket (#06) in the

marked position on the wall and mark the hole for drilling through the Guide Rail Bracket (#06) using a pencil (or center punch). (Fig 7)

The guide rail wall bracket should be

(=)

Note that the bottom of the bracket is thicker than the top

and must be installed correctly

centered in the bracket as shown to allow for vertical adjustment both up and down.

top

bottom

Fig 7

8. Drill a Ø5/16” anchor hole and insert a Wall Anchor (#16). (**See note below)

Separate the Guide Rail Bracket (#06) components (#06a and #06b). Install the Guide Rail Wall Bracket (#06b) to the wall using one ST4.2 x 55mm Countersunk Screw (#21). (Fig 8)

1 * 2

*NOTE: Installation of the Guide Rail

brackets into a stud or 2”x 6” wood reinforcement is strongly recommended.

Ø1/4" or Ø5/16"

#06b

**NOTE: When installing to a stud,

drill a Ø1/4” hole and do not use the anchors.

#06a

Fig 8

12ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

Page 15

9. Dry fit the Stationary Panel Glass (#02) into the

installed U-Channel (For Panel Glass) (#01). Do not

use silicone at this time. (Fig 9)

Use a professional grade glass suction cup if available

Use Caution not to bang the glass

into the U-Channel or threshold.

Fig 9

10. Make sure the Stationary Panel Glass (#02) is parallel to the front edge of the threshold and mark

the position of the glass on the threshold (This line will be different from the line drawn in step#3). Slide the Guide Block (#12) into the notch of the Stationary Panel Glass (#02), and align it flush and square with the edge of the glass. Mark its position on the threshold and also mark the hole for drilling using a pencil (or center punch). (Fig 10)

Fig 10

13ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

Page 16

11. Remove the Stationary Panel Glass (#02)

from the U-Channel (For Panel Glass) (#01) and carefully set it aside. (Fig 11)

12. To install the Guide Block (#12): Loosen the set screw on

the side and remove the guide block face plate. (Fig 12.1) Apply silicone to the underside of the Guide Block (#12) and screw the Guide Block (#12) to the threshold as described below:

*NOTE:

◾For installation into an Acrylic threshold: ◽drill an Ø1/8”(3mm) hole and use the ST4.2 x 25mm Round Head Screw (#18) OR ◾For installation into a Tile threshold:**

◽drill a Ø5/16”(8mm) hole, install Wall anchor 5/16” (#16) and use the ST4.2 x 40mm Countersunk Screw (#17).

(Fig 12)

Fig 11

face plate

use a pencil or

a center-punch to mark the hole

only use anchor

with tile threshold

NOTE: For Tub installations: the bottom bracket must be screwed down to the tub deck.

M5 X 10

Part#12 - Guide Block (with caps)

*see note

Fig 12

14ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

Page 17

TIP: Bring the Door Glass into the shower before the final installation of the Stationary Panel Glass (#02) and

Guide Rail (#04).

13.

Apply silicone into the U-Channel (For Panel Glass) (#01).

Slide the Stationary Glass (#02) firmly into the installed

U-Channel (For Panel Glass) (#01). (Fig 13)

ANEL

Fig 13

OOR

Use Caution not to bang the glass

into the U-channel or threshold.

14. Attach the Stoppers (#05) and Guide Rail Brackets (#06) to both ends of the Guide Rail (#04).

(Notice that the bottom of the Guide Rail Bracket (#06) is thicker than the top). (Fig 14)

top

NOTE: Be careful not to scratch the guide

rail with the brackets and stoppers. Loosen the set screws before installation.

door endpanel end

panel end

bottom

door end

Note that the panel side stopper goes beyond the first glass holder hole

Fig 14

Right-hand door installation shown as example

15ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

Page 18

15. Align the panel end of the Guide Rail (#04) with the installed Guide Rail Wall Bracket (#6b).

Slide the Guide Rail Bracket (#06a) over the Guide Rail Wall Bracket (#06b) and tighten the set screws. (Fig 15)

1 2

Fig 15

TIP: Leave the set screws that hold the Guide Rail (#04) to the Guide Rail Bracket (#06)

loose for now to allow for side-to-side adjustment of the guide rail to make it easier to align

the holes in the guide rail with the holes in the panel glass. Tighten these set screws after the holes are aligned and the glass brackets are installed.

16. Attach the Stationary Panel Glass (#02) to the Guide Rail (#04) using the Glass Brackets (#07).

(Fig 16)

TIP: Pinch the Guide Rail and Panel glass

together to hold the washers in place while inserting the bolt.

Fig 16

16ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

Page 19

17. Level the Guide Rail (#04) across the opening.

If necessary, use the set screws on the Guide Rail Bracket (#06) to adjust the level of the Guide Rail (#04).

(Fig 17 and Fig 18)

To lower the rail:

Loosen the top set screw and tighten the bottom set screw.

To raise the rail:

Loosen the bottom set screw and tighten the top set screw.

NOTE: It is important that the guide rail is level when

marking the position of the Guide Rail bracket on the wall.

18. Using the reference mark on the threshold from Step #3,

draw a plumb line up the wall on the door side of the opening. Measure over 1-1/4” into the shower from this line. With the Guide Rail (#04) level, mark the position of the Guide Rail Bracket (#06) on the wall. (Fig 18)

1-1/4”

Fig 17

”

measure 1-1/4” from the plumb line to the edge of the bracket inside the shower

1-1/4”

with the guide rail level, mark the bottom position of the bracket on the wall

Fig 18

17ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

Page 20

19. Remove the Guide Rail (#04) from the Stationary Panel Glass (#02). Remove the Guide Rail

Bracket (#06) from the Guide Rail (#04) from the door end, hold it back in position on the wall and mark

the anchor hole. Drill a Ø5/16” hole. Separate the Guide Rail Bracket (#06) components (06a and 06b). Attach the Guide Rail Wall Bracket (#06b) to the wall using one ST4.2 x 55mm Countersunk Screw (#21). (Fig 19)

Ø1/4"

2**

or Ø5/16"

Fig 19

*NOTE: Installation of the Guide Rail

brackets into a stud or 2”x 6” wood

reinforcement is strongly recommended. Do not use the Wall Anchor (#16) when installing into a stud/wood).

**NOTE: When installing to a stud, drill a

Ø1/4” hole and do not use the anchors.

#06b

#06a

20. Re-attach the Guide Rail (#04) to the Stationary Panel Glass (#02) and attach the Guide Rail

Brackets (#06). (Fig 20)

NOTE: Be careful not to scratch the upper rail while sliding the brackets onto the guide rail.

To lower the rail:

Loosen the top set screw and tighten the bottom set screw.

To raise the rail:

Loosen the bottom set screw and tighten the top set screw.

Fig 20

18ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

Page 21

21. Measure the distance from the edge of the Guide Block (#12) to the wall. This distance will be (L).

Cut the Anti-Splash Threshold (#11) to the size of: (L). (Fig 21)

Fig 21

22. Apply silicone to the bottom of the Anti-Splash Threshold (#11). Remove the face plate from the

Guide Block (#12). Insert one end of the Anti-Splash Threshold (#11) fully into the Guide Block (#12)

and replace the guide block face plate.

Align the Anti-Splash Threshold (#11) parallel with the front edge of the shower base or threshold. Cover the other end of the Anti-Splash Threshold (#11) with the Threshold End Cap (#10). Apply a small amount of silicone onto the threshold and the wall to prevent leakage. (Fig 22)

Right hand door installation shown as example

Fig 22

19ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

Page 22

23. Secure the Anti-Splash Threshold (#11) to the

threshold with several pieces of painter’s tape to hold it in position tight to the threshold until the silicone cures.

(Fig 23)

Painter’s Tape

NOTE: DO NOT install the handle onto

the door glass until instructed. DO NOT attempt to lift the glass using the handle. This could result in damage to the glass and/or serious personal injury. Always use an assistant or a professional grade glass suction cup when handling heavy glass.

NOTE: Apply Thread Lock (#20) to the roller bolts

during installation.

roller adjustment disk

Fig 23

24. Attach the Rollers (#08) to the Door Glass

(#03) with the wheels facing out. Apply Thread Lock (#20) to the roller bolts during installation. (Fig 24)

NOTE: The roller adjustment disks can be

rotated to tilt the door glass slightly for a better seal into the U-Channel (For Door Glass) (#27) that will be installed in Step #29.

To adjust the Rollers (#08): Support the weight of the door glass with a shim or a glass suction cup. Loosen the roller bolt and rotate the adjustment disk to raise or lower the edge of the door glass. Hold the adjustment disk in place with a small allen wrench and fully tighten the bolt.

Fig 24

20ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

Page 23

25. Align the bottom of the Door Glass (#03) with the Guide Block (#12)

and hang the door from the Guide Rail (#04). (Fig 25)

inside

TIP: Place a pair of 1/2” shims onto

the threshold while installing the Door Glass onto the Guide Rail. Remove the shims once the door is supported by the guide rail.

1/2” Shims

26. Attach the lower Rollers (#08) onto the Door Glass (#03) just below the Guide Rail (#04) with the

wheels facing out. Apply Thread Lock (#20) to the roller bolts. Rotate the roller adjustment disk to raise these lower wheels tight to the Guide Rail (#04) and tighten the bolts. (Fig 26)

Fig 25

NOTE: Apply Thread Lock (#20) to the roller bolts

during installation.

Fig 26

21ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

Page 24

27. To install the

position the stationary panel side of the installation. (Fig 27)

SafeStop™

Bumper (#26) with the 3M tape: Remove the 3M Tape backing and

Bumper (#26) onto the threshold against the U-Channel (#01) on the

NOTE: The surfaces need to be clean and free of construction debris before installing the bumper.

Wipe the area with an alcohol swab before installation

TIP: Install the

using the 3M tape. Screwing the Bumper to the wall using a 5/16” hole and anchor is optional (see step 28).

The

SafeStop™

reversible for Left (as shown below from inside the shower) or Right wall installation

SafeStop™

Bumper (#26) is

Bumper (#26)

REMOVE

3M TAPE

Wall

Inside

Fig 27

Inside

22ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

Page 25

28. To install the

position the panel side of the installation and mark the position of the hole on the wall. Drill a Ø5/16” hole and insert the Anchor (#16). Remove the 3M Tape backing and position the threshold against the U-Channel (#01). Screw to the wall using the ST4.2 x 40 Countersunk screw and re-insert the PVC insert. (Fig 28)

SafeStop™

Bumper (#26) with the screw method: Remove the PVC insert and

Bumper (#26) onto the threshold and against the u-channel on the stationary

SafeStop™

Bumper (#26) onto the

NOTE: construction debris before installing the bumper.

Wipe the area with an alcohol swab before installation.

The surfaces need to be clean and free of

A Phillips head Extender driver bit is recommended for the screw installation method

TIP: When using the screw method, use caution to not crack the wall/tile and to avoid any plumbing behind the wall.

The

SafeStop™

Bumper (#26) is

reversible for Left (as shown below from inside the shower) or Right wall installation

Wall

Inside

Wall

Ø5/16”

Inside

Wall

3M Tape

Wall

Fig 28

23ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

Page 26

29. Hold the U-Channel (For Door Glass) (#27) against the wall on the door side of the opening

to align it with the door glass and mark its position on the wall. **Partially insert two of the U-Channel Bumper Inserts (#28) at the top and bottom and close the door into the U-Channel (For Door Glass) (#27). Mark the position of the U-Channel (For Door Glass) (#27) on the wall along the outside edge. Open the door, hold the U-Channel (For Door Glass) (#27) in place on the wall and mark the holes for drilling. Remove the U-Channel (For Door Glass) (#27) and the U-Channel Bumper Inserts (#28). Drill Ø5/16” anchor holes and insert the Wall Anchors (#16). Apply a bead of silicone to the wall or to the back of the U-Channel (For Door Glass) (#27). Install the U-Channel (For Door Glass) (#27) to the wall using the ST4.2 x 40mm Round Head Screw (#17). Use a 1/4” thick wooden or plastic shim to fully press the U-Channel Bumper Inserts (#28) into the smaller holes in the U-Channel (For Door Glass) (#27) (Fig 29)

DOOR

inside

**Partially insert at two of the U-Channel Bumper Inserts (#28) at the top and bottom of the U-Channel (For Door Glass) (#27) for accurate alignment with the door glass.

Do not cover the holes that need to be marked on the wall.

Failure to use these inserts when aligning the U-Channel (For Door Glass) (#27) may

Ø5/16"

Apply a bead of silicone to the wall or to the back of the U-Channel

Fig 29

NOTE: Use a 1/4” thick wood or plastic shim to

fully press the U-Channel Bumper Inserts (#28) into the U-Channel (For Door Glass) (#27)

24ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

Page 27

TIP: Cover the shower/tub drain before removing the set screws to prevent loss.

30. Remove the set screws from the panel-side Stopper (#05) and apply Thread Lock Adhesive (#20)

to each set screw. Re-insert the set screws into the stopper. Open the door and position the stopper where the door glass makes contact with the SafeStop™ Bumper at the bottom. Tighten the set screws firmly to the Guide Rail (#04). Repeat the same steps for the door-side Stopper (#05), positioning it to make contact with the Roller (#08) when the door is seated in the U-channel Bumper Inserts (#28). Once the Thread Lock Adhesive (#20) is applied to the set screws, reinsert them into the Stopper (#05) and tighten firmly to the Guide Rail (#04). (Fig 30)

panel-side stopper

ANEL

OOR

inside

door-side stopper

5 876

OOR

outside

position stopper where door contacts the SafeStop™

2 3 4

bottom bumper

Fig 30

Stopper

***Position the Panel-side stopper so that the door glass makes contact with the stopper and

SafeStop™ bottom

the

NOTE: The Stoppers (#05) must be positioned correctly to

prevent the handle from contacting the Stationary Glass (#02) and to stop the Door Glass (#03) as it fits into the U-channel Bumper Inserts (#28) in the U-Channel (For Door Glass) (#27)

* Stopper Locations as measured from the wall to the center of the stopper:

• • Panel side: 5” (+/- 1/16“) where the door makes contact with the bottom bumper

• Door side: 3-1/2” (+/-) (depends on opening conditions)

bumper at the same time.

Thread Lock Adhesive

25ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

Page 28

31. Attach the Handle (#15) to the outside of the Door Glass (#03) Make sure all gaskets are in place.

Attach the Anti-Water Strips (#13) to the edges of the Stationary Panel Glass (#02) and Door Glass (#03) where they overlap. (Fig 31)

Door

outside

32. Apply good quality mildew-resistant

silicone along the connection of the u-channels with the walls and the stationary glass with the threshold. (Fig 35)

Fig 31

Hours

Allow 24 hours for the silicone to fully cure before using the shower.

Fig 32

26ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

Page 29

Product Maintenance

BASES and BACKWALLS: To ensure long-lasting life for your acrylic back walls, wipe them off

after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface.

GLASS: To ensure long-lasting life for your glass shower products, wipe them off after each use

with a soft cloth. Rinse and wipe off the glass using either a soft cloth or a squeegee to prevent soap buildup and water spots (Hard water can etch the surface of the glass over time if left to dry). To prevent scratching the surface: never use abrasive cleaners or cleaning products that contain scouring agents. Never use bristle brushes or abrasive sponges that may scratch the surface.

HARDWARE: To ensure a long-lasting finish, wipe off the metal parts after each use with a soft

cloth. Do not use abrasive cleaners or cleaning products containing ammonia, bleach or acid. If accidentally used, rinse the surface as soon as possible to prevent damage to the finish (peeling or corrosion). After cleaning the polished finishes, rinse thoroughly and wipe dry with a soft cloth. Clean stainless steel surfaces at least once a week. When applying stainless steel cleaner or polish to stainless steel hardware, work with (not across) the grain. Never use an abrasive sponge or cloth, steel wool or wired brush as these may permanently scratch the surfaces.

NOTE: To maximize the life of your door, it is important to regularly inspect the glass and all hardware for misalignment, proper attachment, and/or damage. Contact DreamLine

DreamLine

shower doors and enclosures are designed not to leak when

with any questions or concerns.

installed properly and the flow of water is not pointed directly at the vinyl seals.

27ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

Page 30

Enigma-Sky Maintenance Checklist

◻ Guide rail level and tight ◻ Guide rail brackets tight to the walls

o All set screws tight

◻ Inline Panel glass secure ◻ Panel glass brackets tight ◻ Guide block square to the threshold and glass ◻ Proper clearance beneath the door glass: between the threshold and within the guide block ◻ Door Glass adjusted so that the door closes firmly into the bumper inserts in the u-channel ◻ Wheel assemblies tight

o Wheel roller bolts tight ◻ Stoppers tight and positioned correctly o Panel-side stopper set screws tight and secured to the guide rail o Adequate Handle clearance when the door is fully open o Door-side stopper positioned correctly and set screws are tight

◻ SafeStop bumper secured to the wall and threshold ◻ Remove the vinyl seals to inspect the edges of the door glass for concealed damage

o Damaged glass must be replaced! ◻ Replace damaged or missing vinyl seals

28ENIGMA SKY shower and tub door manual Ver 1 Rev 1 02/2018

Page 31

For more information on DreamLine

TEL: 866-731-2244

FAX: 866-857-3638

DREAMLINE.COM

Shower Doors and Enclosures please visit DreamLine.com

DreamLine SHDR656076008, SHDR656076007, SHDR65600ENGIMATUB, SHDR656062007, SHDR654876007 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual