DreamLine SHDR6160762006, SHDR6160762008, SHDR6160762007, SHDR6160622008, SHDR6160622007 User Manual

...

Page 1

ENIGMA-XO

SHOWER/TUB DOOR INSTALLATION INSTRUCTIONS

IMPORTANT

DreamLine For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.com

reserves the right to alter, modify or redesign products at any time without prior notice.

SHDR-61606220-##

Right Hand door installation shown

Please review this entire manual prior to installation.

For more information about DreamLine® Shower Doors & Tub Doors please visit DreamLine.com

ENIGMA-XO manual Ver 1 Rev 2 03/2018

SHDR-61487620-## SHDR-61547620-## SHDR-61607620-##

SHDR-61727620-##

##=finish 06- Oil Rubbed Bronze 07- Brushed Stainless Steel 08- Polished Stainless Steel

Page 2

This model is treated with DreamLine’s

exclusive ClearMax

Glass technology. This is a specially formulated coating that prevents the build up of soap and water spots.

Install the surface with the ClearMaxTM label towards the inside of the shower. Please note that depending on the model, the glass may be coated on either one or both surfaces.

For best results, squeegee the glass after each use and dry with a soft cloth.

ENIGMA-XO manual Ver 1 Rev 2 03/2018

Page 3

Table of Contents

Section title

Model Information

Reinforcement Information

Preparation Tools

Parts List

Installation

Vinyl Seals

Stoppers

SafeStop™ Bumper

Wheel Adjustments

Product maintenance

Page #

7-8

9-27

25-26

ENIGMA-XO manual Ver 1 Rev 2 03/2018

Page 4

IMPORTANT! This manual will describe the installation of the single threshold

model of the Enigma-XO. Use this manual when installing the Enigma-XO single threshold model.

For the ENIGMA-XO Enclosure installation: Start with the Enigma-X/Enigma-XO Enclosure Return Panel manual that is packaged with the return panel glass first for the installation of the return panel glass, then use this manual for the installation of the door section.

ENIGMA-XO

SHOWER/TUB DOOR INSTALLATION INSTRUCTIONS

IMPORTANT

DreamLine

reserves the right to alter, modify or redesign products at any time without prior notice.

For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.com

SHDR-61606220-##

SHDR-61727620-##

SHDR-61487620-## SHDR-61547620-## SHDR-61607620-##

Right Hand door installation shown

Please review this entire manual prior to installation.

For more information about DreamLine® Shower Doors & Tub Doors please visit DreamLine.com

ENIGMA-XO manual Ver 1 Rev 2 03/2018

ENIGMA-XO

SHOWER/TUB DOOR INSTALLATION INSTRUCTIONS

IMPORTANT

reserves the right to alter, modify or redesign products at any time without prior notice.

DreamLine For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.com

SHDR-61606220-##

Right Hand door installation shown

For more information about DreamLine® Shower Doors & Tub Doors please visit DreamLine.com

ENIGMA-XO manual Ver 1 Rev 2 03/2018

##=finish 06- Oil Rubbed Bronze 07- Brushed Stainless Steel 08- Polished Stainless Steel

ENIGMA-X / ENIGMA-XO Shower Enclosure Return Panel manual Ver 1 01/2018

SHDR-61487620-## SHDR-61547620-## SHDR-61607620-##

Please review this entire manual prior to installation.

ENIGMA-X/ENIGMA-XO Enclosure Return Panel

SHOWER ENCLOSURE RETURN PANEL INSTALLATION INSTRUCTIONS

IMPORTANT

reserves the right to alter, modify or redesign products at any time without prior notice.

DreamLine For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.com

NOTE: Use this manual FIRST to install the Return Panel Glass. Then use the manual packaged with the door glass box to continue

with the installation of the shower door section of the enclosure.

Left-Hand Return panel installation

Right-Hand Return panel installation

Please review this entire manual prior to installation.

Shower Doors, Tub Doors & Enclosures, please visit DreamLine.com

For more information about DreamLine

SHDR-61727620-##

##=finish 06- Oil Rubbed Bronze 07- Brushed Stainless Steel 08- Polished Stainless Steel

ENIGMA-X/ENIGMA-XO Enclosure Return Panel

SHOWER ENCLOSURE RETURN PANEL INSTALLATION INSTRUCTIONS

IMPORTANT

DreamLine

reserves the right to alter, modify or redesign products at any time without prior notice.

For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.com

NOTE: Use this manual FIRST to install the Return Panel Glass. Then use the manual packaged with the door glass box to continue

with the installation of the shower door section of the enclosure.

Left-Hand Return panel installation

Right-Hand Return panel installation

Please review this entire manual prior to installation.

For more information about DreamLine

Shower Doors, Tub Doors & Enclosures, please visit DreamLine.com

ENIGMA-X / ENIGMA-XO Shower Enclosure Return Panel manual Ver 1 01/2018

ENIGMA-XO

SHOWER/TUB DOOR INSTALLATION INSTRUCTIONS

IMPORTANT

DreamLine

reserves the right to alter, modify or redesign products at any time without prior notice.

For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.com

SHDR-61606220-##

SHDR-61727620-##

SHDR-61487620-## SHDR-61547620-## SHDR-61607620-##

Right Hand door installation shown

Please review this entire manual prior to installation.

For more information about DreamLine® Shower Doors & Tub Doors please visit DreamLine.com

ENIGMA-XO manual Ver 1 Rev 2 03/2018

##=finish 06- Oil Rubbed Bronze 07- Brushed Stainless Steel 08- Polished Stainless Steel

ENIGMA-X/ENIGMA-XO Enclosure Return Panel

SHOWER ENCLOSURE RETURN PANEL INSTALLATION INSTRUCTIONS

IMPORTANT

reserves the right to alter, modify or redesign products at any time without prior notice.

DreamLine For the latest up-to-date technical drawings, manuals, warranty information or additional details please refer to your model’s web page on DreamLine.com

NOTE: Use this manual FIRST to install the Return Panel Glass. Then use the manual packaged with the door glass box to continue

with the installation of the shower door section of the enclosure.

Left-Hand Return panel installation

Right-Hand Return panel installation

Please review this entire manual prior to installation.

Shower Doors, Tub Doors & Enclosures, please visit DreamLine.com

For more information about DreamLine

ENIGMA-X / ENIGMA-XO Shower Enclosure Return Panel manual Ver 1 01/2018

ENIGMA-XO Enclosure MODEL #s

SHEN-6132482-## SHEN-6132602-## SHEN-6134482-## SHEN-6134542-## SHEN-6134602-##

ENIGMA-XO manual Ver 1 Rev 2 03/2018

ENIGMA-XO Enclosure MODEL #s

SHEN-6132722-## SHEN-6134722-##

Page 5

PANEL

DOOR

IMPORTANT INFORMATION REGARDING THE INSTALLATION OF THIS SHOWER DOOR

Right hand door installation shown as an example

Guide Rail Brackets must be firmly

attached to the wall. Installation into a stud is strongly recommended. All of the guide rail bracket set screws must be tightened.

Thread Lock must be applied to both

stopper set screws. Panel-side stopper must be installed into the pre-drilled stopper hole in the upper guide rail. Door-side stopper must be installed at the proper position to stop the door from contacting the wall.

ENIGMA-XO manual Ver 1 Rev 2 03/2018

Roller Wheel Safety Set Screws must be re-tightened after installation. Apply thread lock.

Lower Roller wheels must be adjusted

during installation to make contact with the Upper Guide Rail. Tighten Safety set screws. Apply thread lock.

Bumper Vinyl Seal must be installed on

the closing edge of the door glass

The Guide Block must be screwed to the

threshold and installed square to the panel glass and door glass. Installing the guide block crooked may damage the bottom edge of the door glass and lead to breakage.

Bumper is secured in position with 3M tape or

screwed to the wall.

PLEASE READ THE ENCLOSED INSTALLATION MANUAL FOR DETAILS REGARDING PROPER INSTALLATION.

THE LATEST VERSION OF THE INSTALLATION MANUAL IS AVAILABLE TO VIEW OR PRINT ON DREAMLINE.COM

Page 6

Reinforcement for Enigma Series

Heavy Glass frameless sliding shower door

Install studs OR install 2”x 6” wood blocking between the studs where the

Guide Rail Brackets will attach to the wall

Stud

measured

from threshold*

(see list below)

2” X 6”

threshold or tub deck

threshold

*Blocking height requirement (to center) as measured from threshold or tub deck: Enigma Air = 73” for shower ht / 59” for tub ht Enigma-X, Enigma-XO = 72-1/2“ for shower ht / 58-1/2” for tub ht Enigma-Z = 73-1/2” for shower ht / 59-1/2“ for tub ht Enigma = 75-1/2” for shower ht only

ENIGMA-XO manual Ver 1 Rev 2 03/2018

or tub deck

Page 7

Preparation

1. After opening all boxes and packages, read this introduction carefully. Check that all of the needed parts are included in the package by marking all the components on the “Detailed Diagram of Shower Door Components”. Examine boxes and packages for shipping damage. If the unit has been damaged, has a finishing defect, or is missing parts, please contact our customer support department within

3 business days of the delivery date. Please note that DreamLine products or missing parts free of charge after 3 business days or if the product has been installed.

Please contact DreamLine

2. Please note that you should consult your local building codes with questions on installation

compliance standards. Building and plumbing codes may vary by location, and DreamLine responsible for code compliance standards for your project and will not accept any returns.

3. If this unit is going to be installed in a new construction, install all of the required plumbing and drainage before installing the shower. Use a competent and licensed (if required by local code)

plumber for all plumbing installation.

4. Make sure that prior to beginning the installation, the surfaces are leveled and solid and will be able to support the total weight of the unit. Also make sure the walls are at right angles. Irregular installation surface level, radius corners or improper angle of side walls will result in serious problems for your installation. Please note that some adjustments and drilling might be necessary during the installation process.

if you have any questions.

will not replace any damaged

is not

5. Protect all primary surfaces of the product during installation. Never set your glass down directly onto a tile floor. Leave corner protectors in place until necessary to remove them. Always use a piece of wood or cardboard to protect the bottom edge and corners of the glass prior to and during installation.

6. This unit must be installed upon a finished threshold and against finished walls.

7. NOTE! This door does not have out-of-plumb adjustment. Make sure your walls are at right angles.

8. This door requires a minimum 2-3/4”of flat threshold space for installation.

9. Note: The installation of this unit requires that you drill down into the threshold.

10. Please note that Step #11 has an option for installing the guide rail brackets to the wall using

anchors. However, the manufacturer strongly recommends installing these heavy doors to the studs or to pre-installed 2”x 6” wood reinforcements behind the wall in the area where the guide rail brackets will be attached to the wall.

Attention: This door is extremely heavy and requires professional installation. Two installers recommended.

NOTE: This door is reversible for right or left-hand door installation. The right-hand door installation is shown as an example throughout this manual. For the left-hand door installation, simply begin on the opposite wall and reverse the orientation of the steps shown.

Do Not hang or drape a towel or wash cloth over the Enigma series guide rail as this may cause the roller wheels to get stuck and possibly cause serious damage or injury.

5ENIGMA-XO manual Ver 1 Rev 2 03/2018

Page 8

Tools

Level

Drill bit (Ø=1/8")

(3mm)

Painter’s Tape

Tape Measure

Drill bit (Ø=1/4")

(6mm)

Razor Knife

Pencil

Drill bit (Ø=5/16") (8mm)

Professional-grade Glass suction cup

Drill bit (Ø=3/8") (10mm)

Phillips Screwdriver

Hammer

Silicone

Chop saw

Hacksaw

Power Drill

Metal File

Tip: Measure the finished opening before proceeding with the installation to be sure that the

correct model size has been ordered.

Be sure to cover the shower drain to prevent losing small parts.

NOTE: Unpack your unit carefully and inspect it. Lay it out and identify all parts using the detailed

diagram and packing list in this manual as a reference. Before discarding the carton, check for small hardware bags that may have fallen to the bottom of the box. If any parts are damaged or missing, please contact DreamLine

your model configuration.

NOTE: Retain these installation instructions for future reference.

for replacement. The shipping boxes may contain extra parts not used in

These instructions will show the installation of the shower door. Please follow the same steps for the installation of the tub door.

6ENIGMA-XO manual Ver 1 Rev 2 03/2018

Page 9

Detailed Diagram ‘A’of Shower Door Components

9a/9b

The glass surface

with the ClearMax™

label must be

installed to face

inside of the shower

PART#

01 Door stopper

9a Wall anchor Ø3/8" (10mm)

10 Large Truss Head Screw ST6x55

DESCRIPTION

Stationary glass

Upper guide rail

Roller

Door Glass

Handle

Glass bracket

Guide rail bracket

Wall anchor Ø5/16" (8mm)

Allen Wrench 3,4,5 mm

(for 48" or 54” or 60")

Packing List A

PART#

QTY

2pcs

1pc

4pcs

1pc

2pcs

3pcs

2pcs

1set

model #s

SHDR-61606220-## SHDR-61487620-## SHDR-61547620-## SHDR-61607620-##

DESCRIPTION

Guide block (with caps)

Bumper strip

Anti-water strip

Anti-splash threshold

Threshold cap

ST4.2x40 Countersunk screw

ST4.2x55 Truss Head screw

Wall bracket

Thread Lock adhesive

Bumper

(for 48" or 54” or 60")

QTY

1pc

2pcs

1pc

2pcs

1pcs

1pc

** not used with the 72” configuration

7ENIGMA-XO manual Ver 1 Rev 2 03/2018

Page 10

Detailed Diagram ‘B’ of Shower Door Components (for 72” model width only)

model #s (for 72” )

SHDR-61727620-##

PART#

DESCRIPTION

Packing List B

QTY PART#

DESCRIPTION

The glass surface

with the ClearMax™

label must be

installed to face

inside of the shower

QTY

Wall anchor Ø5/16"(8mm)

Allen Wrench 3,4,5 mm 1set

Anti-water strip 1pc

ST4.2x55 Truss Head screw 1pc

Wall bracket

2pcs

1pc

Small stationary glass bracket

Small stationary glass Bottom bracket

Small stationary glass

Upper guide rail (for 72")

ST4.2x40 Countersunk screw

1pc

8ENIGMA-XO manual Ver 1 Rev 2 03/2018

Page 11

Installation steps

1. Measure the distance between the two finished

walls at the top, middle and bottom. Measure the width at the model height (62” or 76”). This top measurement will be the “W” dimension used to cut the guide rail to the correct size for the finished opening. Also, check the threshold for level and the walls for plumb. (Fig 1)

Note: The minimum threshold requirement for the ENIGMA-XO is 2-3/4” of flat threshold space.

Top

Middle

Bottom

2-3/4” minimum

Threshold must be level.

2. The Upper Guide Rail (#03) has been pre-cut

for the model width of: 48”, 60” or 72”.

(Note: The actual rail is shorter than the model width by design).

Cut the Upper Guide Rail (#03) from the door end only, which is the end that is farther from the Glass Bracket (#07) holes. (Fig 2)

The length to cut off will be (L) :

Model Width – finished opening W = cut off length (L)

Fig 1

glass bracket holes

door end

*FOR EXAMPLE:

If the model width is 48” and the finished opening is 46”, then you will need to cut 2” off from the door end of the Guide Rail: Example: 48” – 46” = 2” cut off

*Note that this is only an example and the actual cut-off length will vary based on the actual finished opening dimension.

door end

Fig 2

Use a metal file to deburr the cut end

9ENIGMA-XO manual Ver 1 Rev 2 03/2018

Page 12

stationary panel-end

door-end

3a. Attach the Upper Guide Rail (#03) to the Stationary Glass (#02)

with the Glass Brackets (#07) and tighten the bolts into the holes in the Upper Guide Rail (#03). Make sure both adjustment disks are installed in the same direction with the high spot towards the door end. (see *Note below) Make sure that the guide rail is attached parallel with the top edge of the stationary panel glass.

panel end

stopper hole

3b. Slide the Door Stoppers (#01) onto each end of the Upper

Guide Rail (#03). Secure them using the 4mm Allen Wrench (#11). Install the panel-end stopper into the pre-drilled stopper hole in the Upper Guide Rail and apply thread lock to the set screw. (Fig 3.3) Install the door-end stopper approximately 4” from the end

of the guide rail. (The door-end stopper position will be adjusted after the door glass is installed).

3c. Slide the Guide Rail Brackets (#08) onto each end of the

Upper Guide Rail (#03) and secure them. Next, assemble the Wall Bracket (#19) onto the bottom corner of the Stationary Glass (#02) with the bolt facing into the shower as shown in Fig 3.5. Use the supplied gaskets to protect the glass. (Fig. 3 and Fig. 4)

glass bracket

outside

thread lock

Fig 3

measure

disk

*NOTE: The outer glass bracket disk has an eccentric bushing

for adjustment. Be sure to install both glass bracket disks with the high spot of the bushing pointed towards the door end of the guide rail.

Door end of guide rail

High spot of disk bushing

TIP: Mark the location of the high spot on the outer surface of the adjustment disk with a felt tip pen to make adjustment easier to see.

Fig 4

10ENIGMA-XO manual Ver 1 Rev 2 03/2018

Page 13

ATTENTION: This step shows the Small Stationary Glass Bracket (#21) installation for the 72” model only

(not included with the 48“ or 60” model).

4. If the model width is 72” and includes the Small

Stationary Glass (#23), attach the Small Stationary Glass Bracket (#21) to the Upper Guide Rail for 72” (#24) between the Door Stopper (#01) and the Guide Rail Bracket (#08) as shown in Fig. 5.

This bracket will be repositioned during the installation of the Small Stationary Glass (#23). (Fig 5)

Fig 5

disk

5. If the model width is 72” and includes the Small Stationary Glass (#23),

assemble the Wall Bracket (#19) onto the larger notch at the bottom corner of the Small Stationary Glass (#23). Use the provided gaskets to protect the glass. (Fig 6)

outside

Fig 6

outside

NOTE: For single threshold installation (shown), this bracket will be installed to the wall.

For an enclosure installation, this bracket will need to be installed into the threshold.

11ENIGMA-XO manual Ver 1 Rev 2 03/2018

Page 14

6. Place the Stationary Glass (#02) with the Upper Guide Rail (#03) onto the threshold and position it

against the wall. (Note that the Stationary Glass (#02) installs to the outside of the Upper Guide Rail (#03))

Make sure the Stationary Glass (#02) and the Upper Guide Rail (#03) are level. If a horizontal adjustment is required, loosen, rotate and re-tighten the disks on the Glass Brackets (#07). (Fig 7)

rotate disk(s) to level rail

Fig 7

12ENIGMA-XO manual Ver 1 Rev 2 03/2018

Page 15

ATTENTION:

This step shows the Small Stationary Glass (#23) installation for the 72” model only

(not included with the 60” model).

rotate disk(s) to level rail

7. If installing the 72” model:

Unscrew the disk from the Small Stationary Glass Bracket (#21) and loosen the set screw that secures the bracket to the Guide Rail. If necessary, slide the Door Stopper (#01) away from the area so that it will not interfere with the placement of the Small Stationary Glass (#23). Position the Small Stationary Glass (#23) onto the threshold and butt it up against the wall. Align the Small Stationary Glass Bracket (#21) with the hole in the Small Stationary Glass (#23),

re-attach the outer disk and secure the Small

Stationary Glass Bracket (#21) to the Upper Guide Rail for 72” (#24). (Fig 8a and 8b)

Fig 8a

Fig 8b

13ENIGMA-XO manual Ver 1 Rev 2 03/2018

Page 16

8. Once the Upper Guide Rail (#03) is level, mark the position of the Wall Bracket (#19) and Guide

Rail Brackets (#08) on the wall. *NOTE:

wall for the Small Stationary Panel Glass (#23) (see Fig 9.4*). (Fig 9)

If installing the 72” model, also mark the position of the Wall Bracket (#19) on the opposite

1 2 3

inside

for 72” model

inside

Fig 9

9. Make sure that the Stationary Glass (#02) is parallel to the front edge of the threshold and mark it.

Slide the Guide Block (#12) into the notch of the Stationary Glass (#02), and align flush with the edge (Fig 10a). Mark its position and also mark the hole for drilling using a pencil (or center punch.)

Note: If installing the 72” model, also position the Small Stationary Glass Bottom Bracket (#22) with the edge of the Small Stationary Glass (#23) (Fig 10b) and mark its position and the hole for drilling.

(Fig 10a and 10b)

Fig 10a

Fig 10b

for 72” model

14ENIGMA-XO manual Ver 1 Rev 2 03/2018

Page 17

10. After marking the positions of all the hardware, set the

Stationary Glass (#02) with the Upper Guide Rail (#03) aside.

(If installing the 72” model, also remove the Small Stationary Panel Glass (#23) from the Upper Guide Rail (#03)).

Remove the Guide Rail Brackets (#08) from the Upper Guide Rail (#03) and the Wall Bracket (#19) from the Stationary Glass (#02). Place the Wall Bracket (#19) and Guide Rail Brackets (#08) back to the outlined positions and mark the

holes for drilling.

*NOTE: If installing the 72” model, perform the same procedure on the opposite wall to mark the Wall Bracket (#19) for the Small Stationary Panel Glass (#23) (see Fig 11.4*).

(Fig 11)

sleeve

1 2

Fig 11

1 2

Ø5/16” (8mm)

for 72” model

Separate the Guide Rail Bracket (#08) sleeve from the base by loosening the set screws (leave the sleeves on both ends of the upper guide rail)

base

**NOTE: Step #11 has an option for installing the guide rail brackets to the wall using anchors. However, the manufacturer strongly recommends installing these heavy doors to the studs or to pre-installed 2”x 6“ wood reinforcements behind the wall in the area where the guide rail brackets will be attached to the wall.

**For the recommended installation into a stud, drill a Ø1/4” hole up to the stud, do not use wall anchors, and let the screw bore into the wood.

11. Drill a hole for the Wall Bracket (#19) using a Ø5/16”

(8mm) drill bit and insert the Wall Anchor (#9b) (see Fig. 12.1 and 12.2). For the 72“ model, repeat this step for the Wall Bracket (#19)

for the Small Stationary Panel Glass (#23). (Fig 12.7 and 12.8)

Drill the holes for the Guide Rail Brackets (#08) using a Ø3/8” (10mm) drill bit and insert the Wall Anchors (#9a). (see Fig. 12.3**~ 12.6**).

3**

Ø3/8” (10mm)

see Note

4**

5** 6**

7 8

Ø5/16” (8mm)

Ø3/8” (10mm)

see Note

for 72” modelfor 72” model

**If installing into a stud (recommended), drill a Ø1/4” hole and do not use the wall anchors (see note above). (Fig 12)

Fig 12

15ENIGMA-XO manual Ver 1 Rev 2 03/2018

Page 18

12. Fasten the Wall Bracket (#19) to the wall using the ST4.2×55 Truss Head Screw (#18). (Fig 13.1)

If installing the 72” model, repeat this step to install the Wall Bracket (#19) for the Small Stationary Panel Glass (#23) (Fig 13.4).

Install the base parts of the Guide Rail Brackets (#08) onto both walls using the ST6×55 Large Truss Head Screw (#10). Note that the adjustment set screws must be aligned vertically for easier access to

adjust for level if necessary after the glass is installed. Align the set screws vertically and tighten. (Fig 13)

1 2 3 4*

Fig 13

13a. To install Guide Block (#12): Loosen the set screw and

remove the guide block face plate (Fig 14a.5). Apply silicone to the underside of the Guide Block (#12) and screw the Guide

Block (#12) to the threshold as described below:

*NOTE:

◾For installation into an Acrylic Threshold: drill a Ø1/8”(3mm) hole and use the ST4.2 x 40mm

Countersunk Screw (#17) OR

◾For installation into a Tile Threshold: drill a Ø5/16”(8mm) hole, install a Wall Anchor 5/16” (#09b) and use the ST4.2 x 40mm Countersunk Screw (#17).

use a pencil or

a center-punch to mark the hole

only use anchor

with tile threshold

for 72” model

*see note

The Guide Block (#12) must be screwed down. (Fig 14a)

ST4.2 X 40

overhead view of threshold & guide block

M5 X 10

Guide Block must be installed square to the plane of the glass

Part#12 - Guide Block (with caps)

Fig 14a

16ENIGMA-XO manual Ver 1 Rev 2 03/2018

Page 19

13b. If installing the 72” model, repeat Step #13a for the

Small Stationary Glass Bottom Bracket (#22). Loosen the

set screw and remove the Guide Block Face Plate.

use a pencil or a

center-punch to mark the hole

*NOTE:

◾For installation into an Acrylic Threshold: drill an Ø1/8”(3mm) hole and use the ST4.2 x 40mm

Countersunk Screw (#17) OR

◾For installation into a Tile Threshold: drill a Ø5/16”(8mm) hole and use the ST4.2 x 40mm

Countersunk Screw (#17) (with Anchor (#09b) for tile)

Apply silicone to the underside of the Guide Block (#12) and screw the Guide Block (#12) to the threshold. (Fig 14b)

The Small Stationary Glass Bottom Bracket (#22) must be screwed down.

ST4.2 X 40

** use anchor with tile threshold

*see note

Fig 14b

M5 X 10

Part#22 - Small Stationary Glass Bottom Bracket

NOTE: Before you install the Stationary Glass (#02), take

the Door Glass (#05) into the shower area and lean it against the wall with the handle holes on the correct side. After the Stationary Glass (#02) is installed, it may not be possible to easily get the door glass into the shower. Always use padding to protect the glass and shower surfaces.

NOTE: DO NOT attach the handle to the door glass until instructed to do so. DO NOT attempt to lift the door glass with the handle as this may result in damage to the glass and/or serious personal injury. Use a professional grade glass suction cup and an assistant.

protective padding

17ENIGMA-XO manual Ver 1 Rev 2 03/2018

Page 20

14. Re-position the Stationary Glass (#02) and Upper Guide

Rail (#03) onto the threshold and fasten both sleeves of the Guide Rail Brackets (#08) to the brackets on the walls.

Tighten the set screws on the Guide Rail Brackets (#08) to secure the Upper Guide Rail (#03). Position the bracket set screws so that they are accessible from the top and bottom (Fig 15.1 and 15.2).

Assemble the Wall Bracket (#19) at the bottom corner of the Stationary Glass (#02). For the 72“ model, repeat this step for the Wall Bracket (#19) for the Small Stationary Panel Glass (#23) (Fig 15.4) Use the clear vinyl gasket between the glass and the metal parts to avoid contact with the glass, then tighten the bolt with the supplied allen wrench. (Fig 15)

for 72” model

TIP: Adjust the installed Upper Guide Rail (#03) to level as necessary using the Guide Rail Brackets (#08) first and then the Glass Brackets (#07). Start adjustments from the door end.

Panel end

Glass bracket

(Right hand door installation shown as example)

Door end

Guide Rail Bracket

outside

Fig 15

Lower guide rail Raise guide rail

Glass Bracket adjustments

NOTE: Use the Guide Rail Bracket (#08) set screws to adjust the Guide Rail (#03) to level.

To lower the rail:

Loosen the top set screw and tighten the bottom set screw.

To raise the rail:

Loosen the bottom set screw and tighten the top set screw.

18ENIGMA-XO manual Ver 1 Rev 2 03/2018

Page 21

15a. For the 48”or 60“ model size: Measure the

distance from the edge of the Guide Block (#12) to the wall. This distance will be “X”. Use a miter saw or a hacksaw to cut the

Anti-Splash Guard (#15) to the size of: (X) + 3/8”. (Fig 15a)

15b. For the 72” model size: Measure the

distance between the edge of the Guide Block (#12) to the Small Stationary Glass Bottom Bracket (#22). This distance will be “L”.

Use a miter saw or a hacksaw to cut the

Anti-Splash Guard (#15) to the size of: (L) + 3/4”. (Fig 15b)

for 48”or 60“ model

X + 3/8”

measure the distance ‘X’ from the guide block to the wall and add 3/8”

for 72” model

L + 3/4 ”

measure the distance ‘L’ between the guide blocks and add 3/4”

Fig 15a Fig 15b

16. Apply silicone to the bottom of the Anti-Splash Guard (#15). Insert one end of the

Anti-Splash Guard (#15) into the Guide Block (#12).

Align the Anti-Splash Guard (#15) parallel with the front edge of the shower base or threshold.

Cover the other end of the Anti-Splash Guard (#15) with the Anti-Splash Guard Cap (#16) against the wall (48” and 60” models) (see Fig 16.4). (Fig 16)

For the 72” model: Insert the Anti-Splash Guard (#15) into the Small Stationary Glass

Bottom Bracket (#22). (Fig 16.5)

1 42 3

for 48” & 60” model

only use cap when installing up to a wall

for 72” model

Fig 16

19 ENIGMA-XO manual Ver 1 Rev 2 03/2018

Page 22

17. Secure the Anti-Splash Guard (#15) to the threshold with several pieces of painter’s tape to hold it

in position and tight to the threshold until the silicone fully cures. (Fig 17)

Fig 17

18. Attach the Guide block face plate to the installed

Guide Block (#12) and tighten the set screw with the

supplied allen wrench. Use the supplied Decorative caps to cover the screw holes. (Fig 18)

face plate

Fig 18

20ENIGMA-XO manual Ver 1 Rev 2 03/2018

Page 23

19. If installing the 72” model: attach the Small Stationary Panel Glass (#23) to the Upper Guide

Rail (#03) using the Small Stationary Glass Bracket (#21).

Attach the face plate to the Wall Bracket (#19) on the threshold (see Fig 19.5). (Fig 19)

1 2

20. If installing the 72” model: Attach the

Guide block face plate to the installed Small Stationary Glass Bottom Bracket (#22) and

tighten the set screw with the supplied allen wrench. Make sure that the clear gaskets are in place to protect the glass. Use the supplied Decorative caps to cover the screw holes. (Fig 20)

Fig 19

outside

clear gasket

face plate

Fig 20

21ENIGMA-XO manual Ver 1 Rev 2 03/2018

Page 24

NOTE: DO NOT attach the handle to the door glass until instructed to do so. DO NOT attempt to lift the door glass with the handle as

this may result in damage to the glass and/or serious personal injury.

21. Attach two of the Rollers (#04) into the top holes on the

Door Glass (#05) with the wheels facing outside of the shower. Apply Thread Lock Adhesive (#26) to the bolts and safety set screws. Align the safety set screw towards the top for easier access to retighten after installation. (See Fig 21 and page 30 for details)

Lift the door and position the Rollers (#04) onto the Upper Guide Rail (#03) while carefully sliding the bottom edge of the Door Glass (#05) into the groove of the Guide Block (#12).

If necessary, adjust the disks on both Rollers (#04) to ensure that the bottom edge of the Door Glass (#05) does not touch the bottom of the Guide Block (#12) (see details regarding

adjustment on page 28). (Fig 21 and 22)

safety set screw

1 2

outside

safety set screw

Note: The adjustment disks in the wheels are the same as the disks in the Glass brackets and can be rotated to adjust the door glass to create a seal with the wall. See detailed

description on page 28.

TIP: Mark the location of the

high spot on the outer surface of the adjustment disk with a felt tip pen to make adjustment easier to see.

TIP: Use a 3/16” shim beneath the door glass when adjusting the level of the door so that the glass does not make contact with the guide block.

Raise Door glassLower Door glass

Roller wheel adjustment disks

22. Attach two Rollers (#04) into the holes in the Door

Glass (#05) beneath the Upper Guide Rail (#03). Adjust these Rollers (#04) to make conatct with the Upper Guide Rail (#03). Apply Thread Lock Adhesive (#26) to the bolts and safety set screws. Align the safety set screw towards the bottom for easier access to retighten after installation. (Fig 22)

inside

Fig 21

1 2

add threadlock to

the safety set screw

and wheel bolt

Upper Guide Rail

front view

side view

safety set screw

Fig 22

22ENIGMA-XO manual Ver 1 Rev 2 03/2018

Page 25

add threadlock to

the safety set screw

and wheel bolt

NOTE: The Safety set screw on both wheels MUST BE

re-tightened after installation to prevent the large bolt

from coming loose. Apply thread lock during installation.

(See details Fig 23 and also on Page 28)

23. Press the Anti-Water Strip (#14) onto the vertical edge

of the Stationary Glass (#02) and the Door Glass (#05) (Fig 24.1). Press the Bumper Strip (#13) onto the vertical edge of the Door Glass (#05) (48” and 60“ model). (Fig 24.2)

For the 72” model: Attach Anti-Water Strip (#14) to the edge of the Small Stationary Glass (#23). The Bumper Strip (#13) is not necessary with the 72” model (Fig 24.3*).

Attach the Handle (#06) to the Door Glass (#05). (Fig 24)

Note: Use a razor knife to trim the Anti-Water Strip (#14) at

the top to avoid interfering with the lower Rollers (#04).

Fig 23

inline panel

door

inside

72” model

small panel

door

48”or 60”

model

door

wall

outside

(Right hand door installation shown as an example)

Fig 24

23ENIGMA-XO manual Ver 1 Rev 2 03/2018

Page 26

24. Position the Door Stoppers (#01) and screw

them tightly to the Upper Guide Rail (#03).

NOTE: The Door Stoppers (#01) must be

positioned correctly to prevent the handle from contacting the Stationary Glass (#02) (48”, 60” & 72“ models) and to stop the

wall

Door Glass (#05) in a position that allows the bumper strip to create a seal with the wall, but does not allow the door glass to bang into the wall during normal operation (48” & 60” models).

(Fig 24a 24b)

*For the 72” model: Install the door side stopper in a position to

prevent the handle from making contact with the small inline panel glass when the door is in the closed position. (Fig 24b.7)

Fig 24a

door side of opening 48” and 60” models

(+/- 1/8”)

3”

approximately

Door Stopper Installation:

1. Remove the set screw

2. Slide the Door Stopper (#01) onto the Upper Guide Rail (#03)

3. Align with stopper hole (stationary panel side only)

4. Apply Thread Lock Adhesive (#26) to the set screw threads

5. Tighten screw into the stopper hole (stationary panel side only)

6. Correctly position the door side stopper and tighten the set screw with Thread Lock Adhesive (#26)

(Fig. 24b)

Stopper

Panel side

Stopper

hole

Thread Lock

Note: If installing

Door side

Stopper (#01)

Thread

Lock

the 72” model, position the door-side stopper so that the handle cannot make contact with the small inline panel glass

position stopper to allow enough clearance for the handle

small

panel

when the door is in the closed position.

(ENIGMA-XO Right hand door installation shown as an example)

Fig 24b

72” model with Right hand door installation

24ENIGMA-XO manual Ver 1 Rev 2 03/2018

Page 27

25. Install the Bumper (#30) with the 3M tape: postion the Bumper (#30) onto the threshold and

against the wall on the stationary panel side of the installation. (For 72” model, this will be the side of the opening with the large stationary panel). Remove the 3M Tape backing and position the Bumper

(#30) onto the threshold against the Wall Bracket (#19). (Fig 25)

TIP: Install the Bumper (#30) using the 3M

NOTE: The surfaces need to be clean and free of construction debris before installing the bumper. Wipe the area with an alcohol swab before installation

tape. Screwing the bumper to the wall using a 5/16” hole and anchor is optional (see step #26).

The Bumper (#30) is reversible for Left (as shown below from inside the shower) or Right wall installation

Door

Panel

180

3M Tape

Inside

ENIGMA-XO manual Ver 1 Rev 2 03/2018

Inside

Fig 25

Page 28

26. To install the Bumper (#30) with the screw method, position the bumper (#30) onto the

threshold and against the wall on the stationary panel side of the installation. (For 72” model, this will be the side of the opening with the large stationary panel). and mark the position of the hole onto the wall. Drill a 5/16” hole and insert the anchor (###). Remove the 3M Tape and position the Bumper (#30) onto the threshold against the Wall Bracket (#19) and attach using the ST4.2 x 40 Countersunk screw.

(Fig 26)

NOTE: The surfaces need to be clean and free of construction debris before installing the bumper. Wipe the area with an alcohol swab before installation

Door

Panel

TIP: Use caution if using the screw method

to not crack the wall/tile and to avoid any plumbing behind the wall.

The Bumper (#30) is reversible for Left (as shown below from inside the shower) or Right wall installation

1 2

3 4

3M TAPE

ENIGMA-XO manual Ver 1 Rev 2 03/2018

Inside

Fig 26

Page 29

27. Apply a good quality mildew-resistant silicone along the interior perimeter where the glass meets

the wall and threshold and also along the Anti-Splash Guard (#15). (Fig 26)

Please allow 24 hours for the silicone to fully cure before using the shower.

Hours

Fig 27

Do Not hang or drape a towel or wash

cloth over the guide rail as this may cause the roller wheels to get stuck and possibly cause serious damage or injury.

ENIGMA-XO manual Ver 1 Rev 2 03/2018

Page 30

Roller adjustment procedure for Enigma, Enigma-X and Enigma-XO

The bushing that goes through

Insert a small tool (like an

you reghten the big bolt.

Once you have loosened the

This is the adjustment disk.

4 4a

To achieve minimal clearance beneath the door glass without making contact with the boom

guide block and creang a good seal with the wall.

Have at least two 3/16” shims or wedge shims (to maintain space beneath the door glass) and an assistant available to help with this procedure.

Adjust only one wheel at a me and you may need to perform these steps more than once to

get the desired results.

Cauon: The door glass is heavy and may require two people to safely accomplish these steps.

1. the -X) orFirst, loosen and lower either Roller Guards (Enigma Boom Rollers (Enigma, Enigma-XO) to allow

enough room to adjust the upper rollers. (If you have not installed these yet, you will be instructed to in step #7 aer these adjustments are made)

2. Loosen the safety set screw on the roller. (See note 2 below)

3. Loos

en the big bolt just enough so that you can rotate the adjustment disk. (See note 3 below)

4. Rotate the adjustment disk to raise or lower the door slightly with help from an assistant. You can use a small tool (like an allen wrench) to aid in turning this disk by inserng it into the small hole on the edge of the adjustment disk. (see note 4 & 4a below)

5. While holding the adjustment disk in p

lace, reghten the big bolt. Use a shim or have an assistant hold

the door glass in place while you reghten the big bolt.

6. Re-ghten the safety set screw to hold the big bolt in place (see note 5). Test the operaon of the door.

7. For the Enigma-X:Reposion the rollerguards approximately 1/16” beneath the guide rail and

reghten. For the Enigma/Enigma-XO: adjust the lower rollers to make contact with the rail in the same

manner as th

Loosen this safety set screw ﬁrst. This holds the big bolt in place and must be re-ghtened aer the roller is adjusted.

Posion this set screw at

the top for easier access.

It is extremely important that the safety set screw is re-tightened to secure the big bolt.

e upper rollers.

During installaon onto the glass,

rotate this disk so that the safety set screw is at the top for easier access

set screw, you will be able to loosen this big bolt just enough to allow you to rotate the adjustment disk.

Once the big bolt is loosened, rotate this disk to raise or lower the door glass slightly. Use cauon so that the door glass does not make contact with the guide block.

add threadlock to

the safety set screw

and wheel bolt

ENIGMA-XO manual Ver 1 Rev 2 03/2018

the glass is ellipcal and

allows you to raise or lower

the glass when you rotate the

adjustment disk.

allen wrench) into this hole to help rotate this adjustment disk and also to hold the disk in place when

Page 31

Product Maintenance

BASES and BACKWALLS: To ensure long lasting life for your acrylic back walls: wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Avoid the use of aerosol spray cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface.

GLASS: To ensure long lasting life for your glass shower products: wipe them off after each use with a soft cloth. Rinse and wipe off the glass using either a soft cloth or a squeegee to prevent soap buildup and water spots (Hard water can etch the surface of the glass over time if left to dry). To prevent scratching the surface: never use abrasive cleaners or cleaning products that contain scouring agents. Never use bristle brushes or abrasive sponges that may scratch the surface.

HARDWARE: To ensure a long lasting finish: wipe off the metal parts after each use with a soft cloth. Do not use abrasive cleaners or cleaning products containing ammonia, bleach or acid. If accidentally used, rinse the surface as soon as possible to prevent damage to the finish (peeling or corrosion). After cleaning the polished finishes, rinse thoroughly and wipe dry with a soft cloth. Clean stainless steel surfaces at least once a week. When applying stainless steel cleaner or polish to stainless steel hardware, work with (not across) the grain. Never use an abrasive sponge or cloth, steel wool or wired brush as these may permanently scratch the surfaces.

NOTE: To maximize the life of your door, it is important to regularly inspect the glass and other hardware for misalignment, proper attachment, and/or damage. Contact DreamLine

Enigma-XO Maintenance checklist

◻ Guide rail level and tight ◻ Guide rail brackets tight to the walls

o All set screws tight

◻ Panel glass secure ◻ Panel glass brackets tight ◻ Guide block square to the threshold and glass ◻ Proper clearance beneath the door glass between the threshold and within the guide block ◻ Door Glass adjusted so that the Bulb vinyl seal makes even contact with the wall ◻ Wheel assemblies tight

o Wheel roller bolts tight o Wheel assembly safety set screws tight and accessible ◻ Stoppers tight and positioned correctly o Panel-side stopper installed into the pre-drilled hole in the guide rail o Adequate Handle clearance when the door is fully open o Door-side stopper positioned at approximately 3” (+/- 1/8”) (as measured from the wall to the center of the stopper)

◻ Stopper stops the door and bulb vinyl seals to the wall ◻ SafeStop bumper secure to the wall ◻ Bottom Rollers should make contact with the guide rail. ◻ Remove vinyl seals to inspect the edges of the door glass for concealed damage

o Damaged glass must be replaced! ◻ Replace damaged or missing vinyl seals

with any questions or concerns.

29ENIGMA-XO manual Ver 1 Rev 2 03/2018

Page 32

For more information on DreamLine

TEL: 866-731-2244

FAX: 866-857-3638

DREAMLINE.COM

Shower Doors and Enclosures please visit DreamLine.com

DreamLine SHDR6160762006, SHDR6160762008, SHDR6160762007, SHDR6160622008, SHDR6160622007 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual