DreamLine SHDR-3445720-01 User Manual

AQUA ULTRA

SHOWER DOOR & TUB DOOR INSTALLATION INSTRUCTIONS

IMPORTANT!

TM

DreamLine
notice. For the latest up-to-date technical drawings, manuals or any other details please refer
to the support.BathAuthority.com web page.

reserves the right to alter, modify or redesign products at any time without prior

Please read these instructions carefully before installing. If you have any questions regarding

installation, please call our technical support specialists Monday through Friday 9:00 AM – 5:00

PM EST at Phone: [phone], Fax: [phone] or e-mail our technical support group

at [e-mail].

For more information on DreamLineTM Shower Doors & Tub Doors please visit www.BathAuthority.com

Preparation

1. After opening all boxes and packages, read this introduction carefully. Check that all of the needed

parts are included in the package by marking all the components on the “Detailed Diagram of
Shower Door Components”. Examine boxes and packages for shipping damage. If the unit has
been damaged, has a finishing defect, or is missing parts, please contact our customer support
department within 5 business days of the delivery date. Please note that DreamLineTM will not

replace any damaged products or missing parts free of charge after 5 business days or if the
product has been installed. Feel free to contact DreamLineTM if you have any questions.

2. Please note that you should consult your local building codes with questions on installation

compliance standards. Building and plumbing codes may vary by location, and DreamLine is
not responsible for code compliance standards for your project and will not accept any
returns.

3. If this unit is going to be installed in a new construction, install all of the required plumbing and

drainage before installing the shower. Use a competent and licensed (if required by local code)
plumber for all plumbing installation.

4. Prior to installation, ensure that the installation surface is leveled and solid and will be able to

support the total weight of the unit. Also, make sure the walls are at right angles. Irregular
installation surface level or improper angle of side walls will result in serious problems for your
installation. Please, note that some adjustments and drilling might be necessary during the
installation process.

5. This unit must be installed against finished walls and floor.

Instructions are given for the shower door installation. Please, follow the same
instructions to install the tub door.

Tools Required

Waterproof

Tape
Measure Pencil

Phillips
Screwdriver

Drill bit

(Ø=5/16")

Drill bit
(Ø=1/8")

Silicone

Level

“AQUA ULTRA” Rev.2 Ver.1 07/13

Caulk
Gun

Electric
Drill

Hammer

Mallet

Wood

2

Detailed Diagram of Shower and Tub Door Components

7

8

10

11

12

1

5

3

4

6

13

2

Parts List

01 U-Channel 1 (wall profile) 1pc 07 Wall anchor 5pcs
02 U-Channel 2 (bottom profile) 1pc 08 Countersunk screw ST4.2×40 5pc
03 Stationary glass 1pc 10 Countersunk screw ST4.2×25 2pcs
04 Glass door 1pc 11 Side anti-water strip 1pc
05 Support bar 1pc 12 Bottom anti-water strip 1pc
06 Handle 1pc 13 Hinge 2pcs

NOTE: Unpack your unit carefully and inspect it. Lay it out and identify all parts using detailed
diagram of shower door components and parts list on this page as a reference. Before discarding the
carton, check for small hardware bags that tend to fall to the bottom of the box. If any parts are
damaged or missing, please contact DreamLineTM for replacement.

NOTE: Retain these installation instructions for future reference.

“AQUA ULTRA” Rev.2 Ver.1 07/13

3

Shower and Tub Door Installation

3

1. Place the U-Channel 2 (02) onto the

Shower base or Tub. Adjust the U-Channel 2
position in the middle of the ledge.
Mark the drill holes on the ledge through the
predrilled holes in the U-Channel 2 and drill
the holes using Ø1/8” drill bit.

NOTE: If you are installing tub door and
not drilling the holes for U-Channel 2, use
rubbing alcohol to clean the tub ledge of
dirt before applying silicone.

Apply waterproof silicone along the bottom
surface and around the holes of the U-
Channel 2 and fasten it onto the ledge with
the Countersunk screws ST4.2×25 (10）.

See Fig. 1 & 2 for details.
Fig. 1

Fig. 2

1

2

4

5

Ø1/8”

“AQUA ULTRA” Rev.2 Ver.1 07/13

4

2.

Place the U-Channel 1 (01) on the U-
Channel 2 (02) vertically against the
finished wall.
Adjust the U-Channel 1 vertically using
a level.
Mark the drill holes on the wall through
the predrilled holes in the U-Channel 1.
Now drill holes in the wall using Ø5/16

drill bit and insert the Wall anchors
(07).

See Fig. 3 & 4 for details.

2

3

4 1

Ø5/16”

5

Fig. 3

Fig. 4

“AQUA ULTRA” Rev.2 Ver.1 07/13

5

3. Apply waterproof silicone

along the bottom surface

waterproof
silicone

and around the holes of
the U-Channel 1 (01).
Fasten the U-Channel 1
to the wall with the

Countersunk screws
ST4.2×40 (08).

1

Apply Waterproof silicone
into the groove of both
U-Channels.

See Fig. 5 for details.

2

4

Fig. 5

3

4. Slide the Stationary glass

(03) into the groove of both
U-Channels.

NOTE:

If you have difficulty sliding
the Stationary glass into the
U-Channels, you can slightly
tap on the Stationary glass
with a rubber mallet and a
piece of wood.
Apply a bead of silicone on
both ends of the U-Channels,
and its connection.

See fig. 6 for details.

Fig. 6

1

2

3

4

“AQUA ULTRA” Rev.2 Ver.1 07/13

6

2

5. Locate the Support bar (05).

Adjust the Support bar to a proper position on the
Stationary glass (03) and the wall. Level it
horizontally. Hold it firmly and outline the bracket’s
position on the wall. Remove the Support bar and
detach the wall bracket from it. Place the bracket
against its outlined position on the wall and mark the
drilling hole.
Drill the hole using Ø 5/16” drill bit; insert the Wall
anchor (07) and fasten the bracket to the wall with
the Countersunk screw ST4.2×40 (08). Attach the
Support bar to the wall and the Stationary glass and
tighten the set screws and the glass holding screw to
secure the glass.

See Fig. 7 & 8 for details.

Fig. 7

1

3

4

Ø5/16”

6

5

“AQUA ULTRA” Rev.2 Ver.1 07/13

Fig. 8

7

1

6. Attach the Hinges (13) to the Stationary glass (03) with

the decorative bolts facing inside the shower.

See Fig. 9 & 10 for details.

Fig. 9

2

“AQUA ULTRA” Rev.2 Ver.1 07/13

Fig. 10

8

1

7. Bring the Glass door (04) onto the Shower base.

Level up the Glass door next to the Stationary glass (03)
and fasten the Hinges (13) on the Glass Door. Make sure the
top edges of the Glass door and the Stationary glass are
aligned.

See Fig. 11 for details.

Fig. 11

1

2

4

8. Press the Bottom anti-water strip (12) on the bottom

edge of the Glass door (04).

Press the Side anti-water strip (11) on to the vertical
edge of the Glass door.
Install the Handle (06) to the Glass door (04).

2

5

See Fig. 12 for details.

3

Fig. 12

“AQUA ULTRA” Rev.2 Ver.1 07/13

9

9. Let silicone cure properly for about 24 hours.

NOTE: If you are installing tub door and not drilling the holes for U-Channel 2, please keep
an eye if the silicone need to be reapplied to keep the door in good stable condition.

See Fig. 13 for details.

Fig. 13

Product Maintenance

To ensure long lasting life for your acrylic back walls, wipe them off after each use with a soft
cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Never
use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface.

To ensure long lasting life for your glass shower products, wipe them off after each use with a
soft cloth. Rinse and wipe off the glass using either soft cloth or squeegee to prevent soap
buildup. Never use abrasive cleaners and cleaning products that contain scouring agents as
this may scratch the surface. Never use bristle brushes or abrasive sponges.

To ensure a long lasting hardware finish, wipe off the metal parts after each use with a soft
cloth. Do not use abrasive cleaners or cleaning products containing ammonia, bleach or acid.
If accidentally used, rinse the surface as soon as possible to prevent finish peeling or corrosion.
After cleaning the shiny finishes, rinse thoroughly and wipe dry with soft cloth. Clean stainless
steel surfaces at least once a week. When applying stainless steel cleaner or polish, work with
(not against/across) the grain. Never use an abrasive sponge or cloth, steel wool or wired
brushes.

“AQUA ULTRA” Rev.2 Ver.1 07/13

10

TEL: [phone]

FAX: [phone]

WWW.BATHAUTHORITY.COM

For more information on DreamLineTM Shower Doors & Tub Doors please visit www.BathAuthority.com