DreamLine SHDR-242907210-06 User Manual

1

UNIDOOR PLUS

SHOWER DOOR GLASS PANEL INSTALLATION INSTRUCTIONS

Style F

ATTENTION:

This model features the half etched glass option. Please see specific installation
instructions on page 12 when applicable.

IMPORTANT

DreamLineTM reserves the right to alter, modify or redesign products at any time without prior
notice. For the latest up-to-date technical drawings, manuals or any other details please refer
to the support.BathAuthority.com web page.

Please read these instructions carefully before installing. If you have any questions regarding

installation, please call our technical support specialists Monday through Friday 9:00 AM – 5:00

PM EST at Phone: [phone], Fax: [phone] or e-mail our technical support group

at

[e-mail].

For more information on DreamLineTM Shower Doors and Enclosure please visit www.BathAuthority.com

UNIDOOR PLUS, IN-LINE PANEL FULL Ver.1 02/2014

2

Preparation

Caulk

Tape
Measure Pencil

Screwdriver

Phillips Drill bit

Level

Gun

Caulk

Drill

Electric

Hammer

Drill bit

(Ø=5/16")

(Ø=1/8")

Miter saw

Mallet Wood

1. After opening all boxes and packages, read this introduction carefully. Check that all of the needed

parts are included in the package by marking all the components on the “Detailed Diagram of
Glass Panel Components”. Examine boxes and packages for shipping damage. If the unit has been
damaged, has a finishing defect, or has missing parts, please contact our customer support
department within 5 business days of the delivery date. Please note that DreamLineTM will not

replace any damaged products or missing parts free of charge after 5 business days or if the
product has been installed. Feel free to contact DreamLineTM if you have any questions.

2. Please note that you should consult your local building codes with questions on installation

compliance standards. Building and plumbing codes may vary by location, and DreamLine is
not responsible for code compliance standards for your project and will not accept any
returns.

3. If this unit is going to be installed in a new construction, please, install all of the required plumbing

and drainage before installing the shower. Use a competent and licensed (if required by local
code) plumber for all plumbing installation.

4. Prior to the installation, please ensure that the installation surface is level and solid and will be

able to support the total weight of the unit. Also make sure that the walls are plumb. Depending
on the type of unit you are installing, some adjustments in leveling may be possible. However,
irregular installation, surface level or out of square conditions can result in serious problems for
your installation. Please note that some adjustments and drilling may be necessary. Please protect
all primary surfaces of the product during installation. Never set your glass down directly onto a
tile floor. Always use a piece of wood or cardboard to protect the bottom edge and corners of the
glass.

5. Note: The installation of this unit requires that you drill down into the threshold.

Tools Required

UNIDOOR PLUS, IN-LINE PANEL FULL Ver.1 02/2014

3

09

U-channel 1 (76”, wall profile)

1pc

20

Anti-Water strip (Enclosure)

1pc*

11

Stationary glass

1pc

23

Countersunk screw ST4.2x40

14pcs

13

Ø5/16” Wall anchor

14pcs

29

U-channel 2 (40”, bottom profile)

1pc

19

Anti-Water strip (door)

1pc

9

11

13

23

29

19

20

Detailed Diagram of Glass Panel Components

Packing List

NOTE: Unpack your unit carefully and inspect it. Lay it out and identify all parts using the detailed

diagram and packing list in your manual as a reference. Before discarding the carton, check for small
hardware bags that tend to fall to the bottom of the box. If any parts are damaged or missing, please
contact DreamLineTM for replacement. The shipping boxes may contain extra parts not used in your
model configuration.

* ATTENTION: Anti-Water strip (Enclosure) (20) used for 30”- 34” return stationary panel
Installation (STYLE L).

UNIDOOR PLUS, IN-LINE PANEL FULL Ver.1 02/2014

4

Value

inside

outside

outside

inside

Door

Fig. 1

2

1

Style “F”: 6”-34” In-Line Stationary Panel Installation

NOTE: The Unidoor shower door needs to be
installed prior to proceeding with the following
Stationary Glass installation instructions. Please
see the Single Shower Door installation manual
included in the door packaging for complete
shower door installation instructions. Before you
begin the installation, please recheck your shower
opening size. Specific size information can be
found on our website at www.BathAuthority.com.

NOTE: The Unidoor hinge is designed to over close 8°. The
following procedure is recommended to ensure proper
alignment of the panel glass and door.

1. Align the Door so that it is perpendicular to the wall and

parallel to the threshold. Measure across the bottom span of
the Door and threshold on the outside of shower and
determine an equal value.
Mark a line on the threshold base on the handle side

See Fig. 1 for details.

UNIDOOR PLUS, IN-LINE PANEL FULL Ver.1 02/2014

5

H

Fig. 2

W (+) 1"

Fig. 3

NOTE: Use parts from “Detailed Diagram of Glass Panel Components” for the Stationary
Glass assembly and installation.

2. Measure the width of your stationary glass

panel.

NOTE: You will be doing straight cuts for
this stationary panel installation.

*It may be necessary to remove any
burrs from the cut end of the U-channels
with a metal file before placing the U­channel on the glass.

Use a miter saw to rough cut the U-

channel 2 (40”, bottom profile) (29) to
the actual width of the glass (+) 1”.

See Fig. 2 & 3 for details.

UNIDOOR PLUS, IN-LINE PANEL FULL Ver.1 02/2014