Drayton LP111Si, LP241Si, LP711Si, LP722Si, LP522Si Installation Instructions Manual
What isaprogrammer?
...an explanation for householders
Programmers allow you to set ‘On’ and ‘Off’ time periods.
Some models switch the central heating and domestic hot
water on and off at the same time, while others allow the
domestic hot water and heating to come on and go off at
different times.
Set the ‘On’ and ‘Off’ time periods to suit your own lifestyle.
On some programmers you must also set whether you want
the heating and hot water to run continuously, run under the
chosen ‘On’ and ‘Off’ heating periods, or be permanently off.
The time on the programmer must be correct. Some types
have to be adjusted in spring and autumn at the changes
between Greenwich Mean Time and British Summer Time.
You may be able to temporarily adjust the heating programme, for example, ‘Override’, ‘Advance’ or ‘Boost’. These
are explained in the manufacturer’s instructions.
The heating will not work if the room thermostat has switched
the heating off. And, if you haveahot-watercylinder, the
water heating will not work if the cylinder thermostat detects
that the hot water has reached the correct temperature.
INSTALLATION INSTRUCTIONS
PLEASE NOTE: INSTALLATIONMUST ONLY BE
CARRIED OUT BYA QUALIFIED ELECTRICIAN OR
HEATINGENGINEER.
MAKE SURE MAINS INPUT HAS A 3 AMP FUSE.
TECHNICAL DATA
LifestyleProgrammers and Timeswitches conform to the
essential requirementsof these Directives:
2014/30/EC – Electromagnetic compatibility
2014/35/EC – Low voltage
INTRODUCTION Cont...
There are 3 modelsin the Lifestyle range:
LP241Si–a24hrprogram, with central heating and hot water
working independentlyfor up to 3 heating periods eachday, and
everyday the same.
LP522Si– a 5/2-day program allowingfor different timings at
theweekends, with central heating andhot water working
independently forup to3heating periods each day.
LP722Si–a7-dayprogram allowing for different timings on
each day of the week,with central heating and hot water
working independentlyfor up to 3 heating periods eachday.
If theengineer hasn’t set your timings for you,your programmer
will work witha standard program that has been set at the
factory.If this doesn’t suit you, it’s very easyto change it –
when you’ve readthis introductory section, simplygo to the
section thatcontains your programmer model.
Remember:
Make your changesusing the SET?, YES/-, and + buttons on
the programmer, found under the bottom flap.
Youcan’t set ON1 as the last timingbefore midnight, but you
can set OFF3after midnight–providing it’s not more than 23
hours and 59minutes after ON1.
Youneed to set the timings in sequence– i.e. ON1, OFF1, ON2,
OFF2, ON3,OFF3. If you get out of sequence, the displaywill
flash a warning.
SWITCHING
ON 1– start of firsttimed period
OFF 1 –end of first timedperiod
ON 2– start of secondtimed period
OFF 2 –end of secondtimed period
ON 3– start of thirdtimed period
OFF 3 –final switch-off ofthe day
The engineer has setyour program and timings–you
won’t need to doanything else. Just keep this guide in a
safe placefor future reference.
DAY-TO-DAY VARIATIONS
Sometimesyou might need to change the way you use your
centralheating or hot water temporarily – perhaps due to an
unusually coldday, or exceptional demand forhot water.
Here’s how todo it–without affecting your program.
Switchingon and off
On the frontof the programmer there are two Advance/Boost
buttons–one for central heatingand one for hot water.They
allowyou to switch your system either onor off, irrespective of
the program. Soif the heating or hot water is off, andyou want
warmth or hotwater now, you can either–
1. Press Advance toswitch it on (ADV will be displayed),and it will
stay onuntil the end of the ne
xt period.Or if the heating/hot
water ison and you don’t need it, press Advanceand it will go
off untilthe beginning of the next ON period.
Advance willonly operate in TIMED or ONCE modes.
2. Press & HoldBoost to switch on for an extra hour( & BST will
be displayed),then Press again for two ( )or three ( ) hours.
Tocancel Boost, Press Boostagain ( ). Or if theheating/hot
water isalready on, using Boost will extend the ON timeby one,
two orthree hours.
LP241Si,LP522Si & LP722Si PROGRAMMERS
LP111Si &LP711Si TIMESWITCHES
Voltage
230V a.c.+10% - 10% 50Hz
ProgrammerRating
2 (1) A230V a.c. eachswitch
TimeswitchRating
2 (1) A230V a.c.
Ambienttemp
Operating:0º to 45ºC
Storage:-20ºC to 50ºC
Without mainspower
Display:blank
Time:always kept
Programtimes: always preserved
Programmingresolution
1 minute
Wiring
Fixed wiringonly,to comply with
currentIEE regulations
Maintenance Must bemaintained byaqualified
electrician or heatingengineer
Drayton
Tempus6,7
N L 1 2 3 4
Drayton Lifestyle LP112, LP241, LP522, LP722 N L 1 2 3 4
Switchmaster 400, 600 N L 4 3 1
(no connection to terminal 4 on 600)
Switchmaster 805, 900, 900i N L 4 2 3 1
ACL MP (Towerchron) 2 1
ACL FP (Towerchron) 2 1 8 11 6 10
Tempus3, 4, 6,7(old models),
Danfoss Randall
CP15,CP715, FP15,FP715 (Mk18
) E N L 1 2 3 4
Danfoss Randall 3020P, 3060 E 7 6 4 2
Danfoss Randall 4033 (link 1-6) E 7 6 5 3 4 2
Danfoss Randall 102, 102E, 102E5, 102E7 (link 6-3) E 5 6 1 2
Danfoss Randall 701 (link L-5 and 5-6) E N L 3 1
Danfoss Randall 702 (link L-5 and 5-6) E N L 4 2 3 1
Danfoss Randall 922, 972 (link L-2 and 2-5) E N L 1 4 3 6
Danfoss Randall SET2, SET2E, SET3E , SET3M, FP975 E N L 3 6 1 4
SET5 (link L-2and 2-5)
GrasslinTowerchron DP 72, QE2 N L 1 2 3 4
Honeywell ST 699/799 (link L-5 and 5-8) N L 7 4 6 3
Honeywell ST 6200, ST 6300, ST 6400, ST 6450 N L 1 2 3 4
Honeywell ST 7100 (link L-3 and 3-6) N L 7 4 8 5
Horstmann 525,527, 425 Diadem, H21, H27, E N L 3 6 1 4
H121, Tiara (link L-2and 2-5)
Landis&Staefa* RWB2, RWB2E, 20, 40, 102, 200, N L 1 2 3 4
252 & 270, RWB9
Myson Microtimer (link L
-5 and 5-8) N L 7 4 6 3
Potterton Myson All EP2000’s, EP3000’s, EP6000’s N L 1 2 3 4
(link L-5and N-N)
Potterton Myson* Mini Minder N L 1 2 3 4
Sunvic Select 207, SunPro 2000 N L 1 2 3 4
Sunvic SP50, SP100 (link L-3) N L 1 4 2 5
Drayton Tempus 1, 2 (new models) N L 1 2 3 4
Drayton Lifestyle
LP111, LP711, LP111Si, LP711Si
N L 1 2 3 4
Switchmaster 300 N L 4 1
ACL TC (Towerchron) 2 1 4 7
Drayton Tempus 1, 2 (old models) N L 1 2 3 4
Switchmaster 980 N L 4 1
Danfoss Randall TS15, 75 (Mk18) E N L 1 4 2 5/6
Danfoss Randall TS715, TS715Si N L 1 4 2 3
Danfoss Randall TS975 E N L 5 4 6 1,2,3
Danfoss Randall SET1, SET1E E N L 5 4 6
Danfoss Randall SET4 E N L 5 4 6
Danfoss Randall 103, 103E, 103E5, 103E7 4 5 6 3 1 2
Danfoss Randall 911, 971 E N L 5 6 4 2
GrasslinTowerchron QE1 N L 2 4
Grasslin Towerchron T2001,T2001Q E N L 7
Honeywell ST 6100A, ST 6100C N L 1 4 2
Honeywell ST 7000B
Horstmann CentaurSC1, SC7
L
Horstmann
Centaur Plus, C11, C17, C17-ZW
N L 2 4 3
Horstmann Emerald423, Pearl Auto N L 2 4
Horstmann 517,Coronet, H11, H17 E N L 3 4
Landis&Staefa RWB3
N L 4 3
Landis&Staefa RWB30, RWB50,100, 152, 170
N L 4 4 3
Landis&Staefa RWB7
Potterton Myson EP4000, 4001, 4002, 5002 N L 5 4 2
Sangamo M6
Smiths CentrollerMk1, Mk2 N L 3 2
Smiths Centroller30 1 2 3/4
Smiths Centroller300, 980 N
L 4 1
Sunvic Select107, SunProl1000 N L 1 3 2 4
Sunvic SP20,SP35 N L 3 5 4 5
Venner Vennerette N L LINE LOAD
DUAL
CHANNEL
LP241Si,LP522Si, LP722Si
SINGLE
CHANNEL
SINGLE
CHANNEL
Timeswitch
DUAL
CHANNEL
Programmer
for heating OR hot water
LP111Si,LP711Si
Technical Helpline: 0333 7000622
Email: customer.care@draytoncontrols.co.uk
Web: www.draytoncontrols.co.uk
SERVICE INTERVAL
for heating AND hot water
Installation Instructions
06490050001 ISS F
User’s Instructions
TIMESWITCHES
User’s Instructions
PROGRAMMERS
BEFORE INSTALLATION
First,make sure the mains supply is switched off!
PROGRAMMER ONLY
The programmermust be set to the type of system it is to control. Thelink on the back of the unit has two settings–Pand G.
P = a fullypumped and controlled system–allowing
heating and hotwater to be set separately.
G = a gravity-fedhot water system – which does not allow
independent settingof heating without hot water, though
hot watercan be controlled alone.
USING AN EXISTING WALL-PLATE
Loosen thesecuring screws on the old programmer and
unplug it.Check that there’s 70mm clearance to the rightof
the wall-plate,and 25mm above it. Check the chart on the
next page to compare terminalsand if necessary,change the
wiring of thewall-plate to suit. Now plug the Lifestyleunit into
the wall-plateand tighten the securing screws.
Check the 3Afuse, and switch on the mains.
FITTINGANEW WALL-PLATE
The ideallocation is 1.4m above floor level,with reasonable
lighting,good access, no condensation, no extremes of
temperature,andasupporting surface that fully coversthe
back of the unit.
Positionwith 70mm clearance to the right, 25mm above,and
sufficientroom to access the securing screws underneath.
Fix, with terminalsat the top, either direct toaflatwall using wall
plugs and No.6 x 1” (25mm) woodscrews, or on a flush mounting singleconduit box type UA1 (BS4662) usingM3.5 x 14 bolts.
DO NOT USEASURFACEMOUNTING BOX.
TIMESWITCHTERMINAL COMPARISONS
Earth
Neutral
Live
Common
On
Off
Spare
MAKE MODEL
PROGRAMMERTERMINAL COMPARISONS
CurrentModels
Earth
Neutral
Live
Ch1 on
Chl2 on
Ch3 on
Ch4 on
MAKE MODEL
Discontinued/Competitors’Models
*Can simply be removed fromthe backplate andreplaced without any disturbanceto the existing wiring.
WIRING THE TIMESWITCH
Make thewiring connections as
above. Notethat the output
contacts are voltage-free,so
power needsto be put on to
Terminal1 either by linking from
TerminalL or from a separate
supply witha 3A fuse.
WIRING THE PROGRAMMER
Arrowed numbersrelate to
the junctionbox.
Consultboiler handbook
for detailsof pump
overrun wiring.
ConnectionCharts
Wiring ColourCodes
GR Grey
Y Yellow
BK Black
BL Blue
BR Brown
RD Red
W White
OR Orange
YG Yellow/Green
C Common
H Call for Heat
S Satisfied
N Neutral
E Earth
L Live
*Thermostat Key
USINGADRAYTON SIMP-L-FIT, ALTHOUGH NOT
NECESSARY, WILL MAKE THIS INSTALLATION EASIER.
SWITCHING
STANDARDPROGRAM
MON-FRI SAT-SUN
ON 1– start of firsttimed period 6.30am 7.00am
OFF 1 –end of first timedperiod 8.30am 9.00am
ON 2– start of secondtimed period* 12.00pm 12.00pm
OFF 2 –end of secondtimed period* 12.00pm 12.00pm
ON 3– start of thirdtimed period 4.30pm 4.00pm
OFF 3 –final switch-off ofthe day 10.30pm 11.00pm
Lifestyle
DUAL
CHANNEL
LP241Si,LP522Si, LP722Si
SINGLE
CHANNEL
for heating OR hot water
LP111Si,LP711Si
Technical Helpline: 0333 7000622
Email: customer.care@draytoncontrols.co.uk
Web: www.draytoncontrols.co.uk
for heating AND hot water
User’s Instructions
06490050001 ISS F
THE LP711Si7-DAY ELECTRONIC TIMESWITCH Cont...
Changing the timings
Press the SET?button and you’ll see ‘SET PROG?’.
Set all weekdays
First you setthe times that are going to be the samefor each
weekday,then you can selecteach day individually and make
any furtheradjustments. If you want each dayto be quite
different,go straight to ‘Set each day’.
Press the YESbutton, and the display will ask‘SET MON to FRI
PROG?’.
Press YES and you’ll seeON1, the start of your first heating period. Adjustit in 1-minute steps using the–and+ buttons.
If the–and+ buttons are held down, the time changes in
10-minutesteps.
Press SET?,and you’ll see OFF1, the endof your first heating
period. Adjustthis in the same way, press SET?,then repeat
the procedure forON2, OFF2, ON3 and OFF3.
Set each day
If, afteryou’ve set OFF3 you wantto fine-tune one or more
weekdays,press SET? until you find the firstday you want to
adjust –then go through the procedure, altering anytime you
wish. Press SET? tomove on to the next day.When you’ve
finished, press SET?until you see ‘SET SAT SUN PROG?’.
If youdon’t want to alter any individualdays, keep pressing
SET? untilyou see ‘SET SAT SUN PROG?’.
Set weekend
Press YES and alterON1, OFF1, ON2, OFF2, ON3 and OFF3
timesin the same way.
Set each day
If, afteryou’ve set OFF3 for both SAT& SUN, you want to finetune Saturdayor Sunday, pressSET? until you find the first day
you want to adjust– then go through the procedure, alteringany
time youwish. Press SET? to move on to the nextday. When
you pressSET? after setting your hot water forSundays, the programmerwill go back to normal operation.
If youdon’t want to alter either day,keep pressing SET?
until the programmergoes back to normal operation.
If the engineer has setyour program and timings–you
won’t need to doanything else. Just keep this guide in a
safe placefor future reference.
INTRODUCTION
Lifestyle Programmerswill automatically switch your central
heating andhot water on and off at times thatsuit you.
Depending on yoursystem, central heating and hot water
can either bothcome on and off at the same time, or work
independently.The light on the front of the programmer
shows when eachone is on.
PROG?
SAT
SAT SUN
PROG?
MON
PROG?
MON TUE WED THU FRI
INTRODUCTION
Lifestyle Timeswitcheswill automatically controlyour system
by switchingit on and off at timesthat suit you. Thelight on the
front of the timeswitchshows when it’s on.
LP111Si–a24hr program, upto 3 heating periods
each day,and every day the same.
LP711Si–a7-day program, allowingfor different
timings on each day ofthe week, up to 3 heating periods
each day.
If the engineer hasn’tset your timings for you, your timeswitch
will work with a standard program thathas been set at the
factory.If this doesn’t suit you, it’s very easy tochange it –
when you’ve read thisintroductory section, simply turn to
the page for yourtimeswitch model.
Remember:
Make your changes using the SET?, YES/-, and + buttons
Youcan’t set ON1 as the last timing before midnight, but you
can set OFF3 after midnight–providingit’s not more than 23
hoursand 59 minutes after ON1.
Youneed to set the timings in sequence – i.e. ON1, OFF1, ON2,
OFF2, ON3, OFF3. If youget out of sequence, the display will
flash a warning.
SWITCHING
ON 1– start of first timed period
OFF 1 –end of first timed period
ON 2– start of second timed period
OFF 2 –end of second timed period
ON 3– start of third timedperiod
OFF 3 –final switch-off of the day
SINGLE
CHANNEL
Timeswitch
DUAL
CHANNEL
Programmer
SERVICE INTERVAL
Lifestyle
Installer note: After installation, tear along perforations indicated and retain this section - only leave
the User instructions with the end user
Installer note: After installation, tear along perforations indicated and retain this section - only leave
the User instructions with the end user
LP711Si –a7-dayprogram, allowing for different timings on
each dayof the week, up to 3 heating periods each day.
Wantto leaveatiming as it is? Just press SET? and moveon
to the next one.
If you need toreset your timings to the standard programand
start again, press‘SET’ and ‘+’ together to go backto the
pre-set program.
Yoursystem will come on for up to 3 heating periodsevery
24hrs. ON1 starts thefirst one, OFF1 finishes it, and so on.
Notice thatON2 and OFF2 are set to the same time.* This
means your system won’t respond,but if you want to activate
that middle period orchange any other timings–read on.
The standard program
When you press SET? after settingOFF3, the timeswitch will
return tonormal operation.
If the engineer hasset your program and timings–youwon’t
need to do anythingelse. Just keep this guide inasafe place
for future reference.
Sometimesyou might need to change the way you useyour
system temporarily– perhaps due to an exceptionally cold day.
Here’s how to doit–without affecting the timings in your
program.
Switching on and off
On the frontof the timeswitch there is an Advance/Boost button.
It allows you to switchyour system either on or off, irrespectiveof
the program.So if the heating is off, and you want warmth now,
you can either –
1. Press Advance toswitch it on (ADV will be displayed), and itwill
stay on until theend of the next period. Or if the heating is on and
you don’t need it, press Advanceand it will go off until the
beginning of thenext ON period.
Advance will only operate inTIMED or ONCE modes.
2. Press&Hold Boost to switchon for an extra
hour ( & BST will
be displayed), thenPress again for two ( ) or three ( ) hours.
Tocancel Boost, Press Boost again ( ). Or if the heating is
already on, using Boost willextend the ON time by one, two or
three hours.
DAY-TO-DAYVARIATIONS
Over-riding the program
At theside of the display there
are four operating modes:
OFF = continuouslyoff.
TIMED = on for up to 3 periods a day.
ONCE = on for 1 periodaday,from the start of ON1
to theend of OFF3.
ON = continuouslyon.
Use the SELECT buttonunder the flap to change the
mode.
This won’t alter thetimings in your program, which you
can return toby selecting TIMED.
THE LP111Si 24hr ELECTRONIC TIMESWITCH
LP111Si –a24hrprogram, up to 3 heating periods eachday,
and everyday the same.
Wantto leaveatiming as it is? Just press SET? and moveon
to the next one.
If you need toreset your timings to the standard program
and start again,press ‘SET’ and ‘+’ together to go backto
the pre-set program.
The standard program
Yoursystem will come on for up to 3 heating periodsevery
24hrs. ON1 starts thefirst one, OFF1 finishes it, and so on.
Notice thatON2 and OFF2 are set to the same time.* This
means your system won’t respond,but if you want to activate
that middle period orchange any other timings–read on.
SWITCHING STANDARDPROGRAM
ON 1– start of first timed period 6.30am
OFF 1 –end of first timed period 8.30am
ON 2– start of second timed period* 12.00pm
OFF 2 –end of second timed period* 12.00pm
ON 3– start of third timedperiod 4.30pm
OFF 3 –final switch-off of the day 10.30pm
Changing the timings
Press theSET? button and you’ll see ‘SET PROG?’.
PROG?
Press theYES button, and you’ll see ON1, the start of your first
heating period.Adjust it in 1-minute steps using the–and +
buttons. If the–and+ buttons are held down, the time changes
in 10-minutesteps.
Press SET?, and you’ll seeOFF1, the end of your first heating
period. Adjustthis in the same way, press SET? thenrepeat the
procedure for ON2, OFF2, ON3andOFF3
Over-riding the program
LP241Si –a24hr program,with central heating andhot water
working independentlyfor up to 3 heating periods each day,
and everyday the same.
If the timingshaven’t been set for you, then your programmer
will still beon the factory-set standard 24hr program,with
centralheating and hot water operating togetheron the
same timingsfor every day of the week. But it’s easyto make
changes,and have heating and water working independently
– just followthe instructions.
Wantto leaveatiming as it is? Press SET? andmove on to
the next one.
If you needto reset your timings to the standard program
and start again, press‘SET
’ and ‘+’together to go back to
the pre-set program.
If you don’tpress anything for two minutes, the programmer
automaticallygoes back to normal operation.
THE LP241Si 24hr ELECTRONIC PROGRAMMER
OFF = continuouslyoff.
TIMED = on for up to 3 periods a day.
ONCE = on for 1 periodaday, from the startof ON1
to the end of OFF3.
ON = continuouslyon.
On eachside of the display there arefour operating modes –
one groupfor central heating, the other forhot water. Youcan
change modeswith immediate effect by using the appropriate
SELECT button. This won’t alterthe timings in your program,
which youcan return to by selecting TIMED.
on the programmer, found under the bottom flap.
Pollution degree
Software class
Ball pressure test
temperature
Rated impulse voltage
2
2
75ºC
2.5kV
E
4 6
3
1
Salus EP101, SP120
4
3
NL
Myson
Myson
N L 1 3 2 4
MEPIC
4
Mictrotimer (link L-5 and 5-8)
E N L 5 6
E
N L
423
3
3 2
N L 1 2 3 4
British Gas EMT2, UT1, UT2
N L 1 324
Drayton
Drayton
Drayton
N L 1 2 3 4
N L 1 2 3 4
N L 1 2 3 4
SM1
miGenie Wish 1
MiTimeMT711R, MiTime RF Pack1
CurrentModels
Discontinued/Competitors’Models
Sangamo M5 (link 1-6)
N L 1
8
N L 1 2 3 4
Salus EP200, SP220
Myson MEP2C
N L 1 2 3 4
Drayton
Drayton
Drayton
British Gas
SM2
miGenie Wish 2
MiTime MT721R, MiTimeRF Pack 2 & 3
EMP2, UP1, UP2
N L 1 2 3 4
N L 1 2 3 4
N L 1 2 3 4
N L 1 2 3 4
06490050 ISS F 12/02/2016 Page 1
USERS NOTES
I Pressthe SET? buttonuntil you see SET CLOCK?.
Set the hour
I PressYES once, andthen the hour willstart to flash. Use the
– and +buttons to set the hour,checking forAM andPM.
Set the minute
I PressSET?, and the minuteswill start to flash.Use the – and +
buttonsto set the exacttime.
I PressSET?, and ‘SET DATE?’appears in the display.
If youdon’t want to changethe date press SET?to goback to
normaloperation. If you do,go onto the nextsection.
SETTINGTHE DATE
The weekdayis automaticallycalculated from the date,so if
the weekdayis incorrect you’llneed to reset the date.
I Pressthe SET? buttonuntil you see SET DATE?.
Set the year
I PressYES and the yearwill start to flash.Use the – and + but-
tons toadjust.
Set the month
I PressSET? and the month willstart to flash. Usethe –and +
buttonsto adjust.
Set the day
I PressSET? and the day willstart to flash. Use the– and + but-
tons toadjust.
Set the Day Light Saving
I PressSET? and the currentDLS status willstart to flash for day
lightsaving (British SummerTime). Use the – and+ buttons to
turn onor off.
I PressSET? to go back to normaloperation.
Gravity HW, Pumped CH with Room Stats
WEEKDAYS WEEKENDS
HW CH HW CH
ON1 – startof first timedperiod 6.30am 6.30am 7.00am 7.00am
OFF1 – endof first timedperiod 8.30am 8.30am 9.00am 9.00am
ON2 – startof secondtimed period* 12.00pm 12.00pm 12.00pm 12.00pm
OFF2 – endof secondtimed period* 12.00pm 12.00pm 12.00pm 12.00pm
ON3 – startof thirdtimed period 4.30pm 4.30pm 4.00pm 4.00pm
OFF3 – finalswitch-off ofthe day 10.30pm 10.30pm 11.00pm 11.00pm
SWITCHING
WEEKDAYS WEEKENDS
HW CH HW CH
ON1 – startof first timedperiod 6.30am 6.30am 7.00am 7.00am
OFF1 – endof first timedperiod 8.30am 8.30am 9.00am 9.00am
ON2 – startof secondtimed period* 12.00pm 12.00pm 12.00pm 12.00pm
OFF2 – endof secondtimed period* 12.00pm 12.00pm 12.00pm 12.00pm
ON3 – startof thirdtimed period 4.30pm 4.30pm 4.00pm 4.00pm
OFF3 – finalswitch-off ofthe day 10.30pm 10.30pm 11.00pm 11.00pm
SWITCHING
WIRINGTHE PROGRAMMER Cont...
ConnectionCharts
Makethe wiring connections,as above, forthe appropriatesystem.
Forsurfacewiring,snap outthe cableentrystripon the bottom edge
ofthe wall-plate.Lifestyleunitsare double-insulatedand needno earth
connection,but anearthingcontinuity (loop)terminal isprovidedfor
convenience.
Afterwiring,plugin the unitandtightenthe securingscrews.
Checkthe mains inputhasa 3A fuse,andswitch onthe mains.
Thenset thetimingsas shownin theUser’sGuide.
ALWAYSSWITCH OFFTHE MAINSBEFOREREMOVING
THELIFESTYLETIMESWITCH/PROGRAMMER– AND
NEVERFIT IT TOA LIVE WALL-PLATE!
SERVICEINTERNAL FEATURE
Applicableto all models.
Ifyou wishto activate, oradjust,the settings forthe ‘serviceinterval’
feature thenpleasereferto the instructionsforthe serviceinterval
(LPSi) resetmodule[SOLDSEPARATELY]
Technical Helpline: 0
333 7000622
Email: customer.care@draytoncontrols.co.uk
Web: www.draytoncontrols.co.uk
INSTALLERS/ENGINEERS NOTES
THE LP522Si5/2-DAY ELECTRONICPROGRAMMER Cont...
Changingthe timings
I Pressthe SET? buttonand you’ll see‘SET PROG?’.
Set the weekday centralheating
I Pressthe YES button, andthe display willask ‘SET CH MONto
FRI PROG?’.
I PressYES and you’ll see ON1,the start of your firstcentral heat-
ing period.Adjust it in 1-minutesteps using the– and+ buttons.If the– and + buttonsare held down, thetime changes in
10-minutesteps.
PROG?
MON TUE WED THU FRI
CH
PROG?
THE LP241Si24hr ELECTRONICPROGRAMMER Cont...
The standardprogram
Yoursystem will comeon for up to 3 heatingperiods every 24hrs.
ON1 startsthe first one, OFF1finishes it, and soon. Notice thaton
the standardprogram ON2 andOFF2 are set to the sametime for
both centralheating and hotwater. * Thismeans your system won’t
respond,but if you want to activatethat middle period,or change
any othertimings – read on.
Changingthe timings
I Pressthe SET? buttonand you’ll see‘SET PROG?’.
Set the central heating
I Pressthe YES button,and the displaywill ask ‘SET CH PROG?’.
I PressYES and you’ll see ON1,the start of your firstcentral heat-
ing period.Adjust it in 1-minutesteps using the– and+ buttons.If the– and + buttonsare held down, thetime changes in
10-minutesteps.
I PressSET?, and you’ll seeOFF1, the end of yourfirst central
heatingperiod. Adjust thisin the same way,press SET?, then
repeatthe procedurefor ON2, OFF2, ON3and OFF3.
Set the hot water
I Whenyou press SET?after setting OFF3 forthe central heating,
the displaywill ask ‘SET HWPROG?’.
I PressYES, then set your timesin the same way.Remember,in
this modeyou can have differenttimes to your centralheating if
you wish.
I Whenyou press SET?after setting OFF3 forthe hot water,the
programmerwill return tonormal operation.
THE LP522Si5/2-DAY ELECTRONICPROGRAMMER
LP522Si– a 5/2-day program allowingfor different
timingsat the weekends, withcentral heating and hotwater
workingindependently forup to 3 heating periods eachday.
If the timingshaven’t been setfor you, then your programmer
will stillbe on the factory-setstandard program.This means
that centralheating and hot waterwill operate together, with
the sametimings for weekdaysand different ones forthe
weekend.But it’s easy to makechanges, and have heating
and waterworking independently– just follow the instructions.
Wantto leave a timing as it is? PressSET? and move on to
the nextone.
If you needto reset your timingsto the standard program
and startagain, press ‘SET’ and‘+’ together to go backto
the pre-setprogram.
If you don’tpress anything fortwo minutes, the programmer
automaticallygoes back to normaloperation.
The standardprogram
Yoursystem will comeon for up to 3 heatingperiods every
24hrs.ON1 starts thefirst period, OFF1 finishesit, and so on.
Noticethat ON2 and OFF2 areset tothe same time.*This
meansyour system won’trespond, but if youwant to activate
that middleperiod, or changeany other timings– readon.
PROG?
PROG?
CH
I PressSET?, and you’ll seeOFF1, the end of yourfirst central
heatingperiod. Adjust thisin the same way,press SET?, then
repeatthe procedurefor ON2, OFF2, ON3and OFF3.
Set weekday hot water
I Whenyou press SET?after setting OFF3for the central heating,
the displaywill ask ‘SET HWMON toFRI PROG?’.
I PressYES, then set your timesin the same way.Remember,in
this modeyou can have differenttimes to your centralheating if
you wish.
Set weekend centralheating
I Whenyou press SET?after OFF3 for the weekdayhot water,
the displaywill ask ‘SET CHSAT SUN PROG?’. PressYES to
confirm,and alter the timesin the same way.
Set weekend hot water
I Whenyou press SET?after OFF3 for the weekendcentral
heating,the display willask ‘SET HW SATSUN PROG?’.
PressYES, and followthe procedure.
I Whenyou press SET?after OFF3 for HW SATSUN, the
programmerwill go back to normaloperation.
THE LP722Si7-DAY ELECTRONICPROGRAMMER
LP722Si– a 7-day program allowingfor different timings
on eachday of the week, with centralheating and hot water
workingindependently forup to 3 heating periods eachday.
If the timingshaven’t been setfor you, then your programmer
will stillbe on the factory-setstandard program.This has central
heatingand hot water operatingtogether – with the optionof
havingdifferent timings foreach day of the week. Butit’s easy
to makechanges, and have heatingand water working
independently– just followthe instructions.
Wantto leave a timing as it is? PressSET? and move on to the
next one.
If you needto reset your timingsto the standard programand
startagain, press ‘SET’ and ‘+’together to go back to the
pre-setprogram.
If you don’tpress anything fortwo minutes, the programmer
automaticallygoes back to normaloperation.
The standardprogram
Yoursystem will comeon for up to 3 heatingperiods every
24hrs.ON1 starts thefirst period, OFF1 finishesit, and so on.
Noticethat ON2 and OFF2 areset tothe same time.*This
meansyour system won’trespond, but if youwant to activate
that middleperiod, changeany other timings– read on.
Changingthe timings
I Pressthe SET? buttonand you’ll see‘SET PROG?’.
PROG?
CH
SAT SUN
SERVICEINTERVAL FEATURECont...
Youshould contact yourservice engineer to arrangea service.
I Whenthe ‘service’is dueit will display;
I An audiblealarm will sound;push any button tosnooze the
alarmfor 24hrs
If you haven’talready arrangedfor a service, you should
contactyour service engineerimmediately.
SETTINGTHE CLOCK AND DATE
Applicableto all models.
SETTINGTHE CLOCK
The clockin your programmer hasbeen set at the factory,
and automatically accountsfor British Summer Time.
However,should you needto set the clock, readon.
I PressSET?, and you’ll seeOFF1, the end of yourfirst central
heatingperiod. Adjust thisin the same way,press SET?, then
repeatthe procedurefor ON2, OFF2, ON3and OFF3.
LP722Si
7-DAYELECTRONIC PROGRAMMERCont...
I Whenyou press SET?after setting OFF3 forthe weekday central
heating,the display willask ‘SET HW MON toFRI PROG?’.
I PressYES, then set your hotwater times in the sameway.
Remember, in this modeyou can have differenttimes to your
centralheating if you wish.
Set each day
If, afteryou’ve set OFF3 foryour hot water,you want to fine-tune
one ormore weekdays,press SET? until you findthe first day
you wantto adjust – thengo through theprocedure, alteringany
time youwish. Press SET? tomove onto the nextday. When
you’vefinished, press SET?until you see ‘SET SATSUN
PROG?’.
If youdon’t want to alterany individual days,keep pressing
SET? untilyou see ‘SET SATSUN PROG?’.
Set weekend
I PressYES, and alter thecentral heating and hotwater times in
the sameway.
I Whenyou press SET?after OFF3 for HW SATSUN, the pro-
grammerwill ask the questionTEST? If you want totest your
program,see below, otherwisepress SET? again.If you don’t
want totest your program,press SET? again– andyou’ll be
askedthe question SETH’DAY? If you wantto set a holiday
switchoff, see page 23, otherwisepress SET? again.Ifyou’re not
goingto program in a holidayswitch-off,then press SET?again
and yourprogrammer will goback to normal operation.
SERVICEINTERVAL FEATURE
Applicableto all models.
If yourinstaller has configuredthe ‘service interval’feature,
then yourprogrammer will displaythe following information.
I 30 daysbefore the next ‘service’is due it willdisplay;
I then
I then
I andthen revert to thenormal time display.
The displaywill cycle continuously. When you see
this it means;SERVICE DUE ON 25
th
DECEMBER.
SAT SUN
PROG?
MON
Installer note: After installation, tear along perforations indicated and retain this section - only leave
the User instructions with the end user
Installer note: After installation, tear along perforations indicated and retain this section - only leave
the User instructions with the end user
THE LP722Si7-DAY ELECTRONICPROGRAMMER Cont...
Set all weekdays
Firstyou set the timesthat are goingto bethe same for each
weekday,then you canselect each day individuallyand make
any furtheradjustments.If youwant each dayto bequite different, gostraight to ‘Set eachday.’
I Pressthe YES button, andthe display willask ‘SET MON toFRI
PROG?’.
I PressYES and the displaywill ask ‘SET CHMON toFRI
PROG?’.
I PressYES, and you’ll seeON1, the start ofyour first central
heatingperiod. Adjust itin 1-minute stepsusing the – and +
buttons.If the – and + buttonsare held down,the time changes
in 10-minutesteps.
PROG?
MON TUE WED THU FRI
CH
PROG?
MON TUE WED THU FRI
SWITCHING STANDARDPROGRAM
ON 1– start of firsttimed period 6.30am
OFF 1– end of firsttimed period 8.30am
ON 2– start of secondtimed period* 12.00pm
OFF 2– end of secondtimed period* 12.00pm
ON 3– start of thirdtimed period 4.30pm
OFF 3– final switch-offof the day 10.30pm
Technical Helpline: 0333 7000622
Email:
customer.care@draytoncontrols.co.uk
Web: www.draytoncontrols.co.uk
06490050 ISS F 12/02/2016 Page 2
LWC3 Junction Box
Pump
Boiler
Room Thermostat
Cyl. Thermostat
Programmer
Mains Input
230V 50HZ
*
7
2 3
L
N
E
* 1 2 3 7
N
E
Switch
L
Perm.
L
Refer to Boiler Handbook
for wiring details of Pump
Overrun boilers. Use boiler
manufactures instructions.
*
RTS 1&2
RTS 4,6,9&10
Function
N
N
NLLE
L 1
3
3
COM
CALL
SAT.
Function
COM
CALL
SAT.
Drayton
HTS 3
C
1
2
Lifestyle LP722 LP522 LP241 LP112 SM2
NOT
USED
2
N
1
L
1 2 3 4
HW
OFF
CH
OFF
HWONCH
ON
Mains
Isolator
1
L
2N3
E
3A
3 2 1 4
5
8 6
8
4
21 3
4 567 8 9 10 11 12
L N E
Motorized Valves
The white wire (28mm Valves) becomes live when the valve closes, it is not
used and is wired to ‘spare’ terminals for sale isolation.
Drayton
22mm 2 Port Valve
28mm 2 Port Valve
Function of
Leads
DHW VALVE
Motor Aux.SW
L
L
Motor
Aux.SW
CH VALVE
N
N
2
2
N.O
N.O
N.C
N.C
E
E
33
C
C
6 77119
105
Brown
Brown
Blue
Blue
Yell/Green
Yell/Green
Orange
Grey
Orange
Grey
White
(28mm only)
White(28mm only)
Spring-Return 2-Valve System
LWC3 Junction Box
Pump
Boiler
Room Thermostat
Cyl. Thermostat
Programmer
Mains Input
230V a.c.
Motorized Valves
*7
2 E
L
N
E
* 1 2 3 7
N
E
Switch
L
Perm.
L
RTS 1&2
RTS 4,6,9&10
Function
N
N
NLLE
L 1
3
3
COM
CALL
SAT.
Function
COM
CALL
SAT.
Drayton
HTS 3
C
1
2
Lifestyle LP722 LP522 LP241 LP112 SM2
NOT
USED
2
N
1
L
1 2 3 4
HW
OFF
CH
OFF
HWONCH
ON
Mains
Isolator
1
L
2N3
E
3A
Drayton
22mm 3 Port Mid Position Valve
28mm 3 Port Mid Position Valve
Function of
Leads
Blue
Yell/Green
Grey
Orange
White
3 2 1 4
5
6 7
8
8 6
4
CH
On
HW
Off
Boiler
Live &
HW on
N E
5 8
723
1 2 3
4 567 8 9 10 11 12
L N E
Refer to Boiler Handbook
for wiring details of Pump
Overrun boilers. Use boiler
manufactures instructions.
*
Mid-Position Valve System
Pump
L
N
E
5 2 3
Boiler
* 1 2 3 7
N
E
Switch
L
Perm.
L
LWC3 Junction Box
1 2 3
4 567 8 9 10 11 12
L N E
Programmer
Lifestyle LP722 LP522 LP241 LP112 SM2
NOT
USED
2
N
1
L
1 2 3 4
HW
OFF
CH
OFF
HWONCH
ON
7
4
Mains Input
230V a.c.
Mains
Isolator
1
L
2N3
E
3A
Room Thermostat
RTS 1&2
RTS 4,6,9&10
Function
N
NLLE
L 1
3
3
COM
CALL
SAT.
3 1 2 4
5
N
Loading...