Drayton LP111Si, LP711Si, LP241Si, LP522Si, LP722Si User Instructions
DAY-TO-DAY VARIATIONS Cont...
Over-riding the program
At the side of the display there are four operating modes:
OFF = continuously off.
TIMED = on for up to 3 periods a day.
ONCE = on for 1 period a day, from the start of ON1
to the end of OFF3.
ON = continuously on.
Use the SELECT button under the flap to change the mode.
This won’t alter the timings in your program, which you can
return to by selecting TIMED.
DUAL
CHANNEL
LP241Si, LP522Si, LP722Si
SINGLE
CHANNEL
for heating OR hot water
LP111Si, LP711Si
Invensys Controls Europe
Sales: 0845 1305522 / Technical Helpline: 0845 1307722
Email: customer.care@invensyscontrols.com / Web: www.draytoncontrols.co.uk
for heating AND hot water
User’s Instructions
06490050001 ISSC
S
INGLE
CHANNEL
Timeswitch
D
UAL
CHANNEL
Programmer
SERVICE INTERVAL
Lifestyle
DAY-TO-DAY VARIATIONS
Sometimes you might need to change the way you use your
system temporarily – perhaps due to an exceptionally cold day.
Here’s how to do it – without affecting the timings in your
program.
Switching on and off
On the front of the timeswitch is an Advance button. It allows
you to switch your system on or off, irrespective of the program.
Press Advance to switch it on, and it will stay on until the end
of the next OFF period. Turn it off, and it will stay off until the
beginning of the next ON period.
If the engineer has set your program and timings – you won’t
need to do anything else. Just keep this guide in a safe place
for future reference.
O
ver-riding the program
At the side of the display there are four operating modes:
OFF = continuously off.
TIMED = on for up to 3 periods a day.
ONCE = on for 1 period a day, from the start of ON1
t
o the end of OFF3.
ON = continuously on.
Use the SELECT button under the flap to change the mode.
This won’t alter the timings in your program, which you can
return to by selecting TIMED.
THE LP111Si 24hr ELECTRONIC TIMESWITCH
LP111Si – a 24hr program, up to 3 heating periods each day,
and every day the same.
Want to leave a timing as it is? Just press SET? and move on
to the next one.
If you need to reset your timings to the standard program
and start again, press ‘SET’ and ‘+’ together to go back to
the pre-set program.
The standard program
Your system will come on for up to 3 heating periods every
24hrs. ON1 starts the first one, OFF1 finishes it, and so on.
Notice that ON2 and OFF2 are set to the same time.* This
means your system won’t respond, but if you want to activate
that middle period or change any other timings – read on.
SWITCHING STANDARD PROGRAM
ON 1
– start of first timed period 6.30am
OFF 1
– end of first timed period 8.30a m
ON 2
– start of second timed period*
OFF 2
– end of second timed period* 12.00pm
DUAL
CHANNEL
LP241Si, LP522Si, LP722Si
SINGLE
CHANNEL
LP111Si, LP711Si
Invensys Controls Europe
Sales: 0845 1305522 / Technical Helpline: 0845 1307722
Email: customer.care@invensyscontrols.com / Web: www.draytoncontrols.co.uk
User’s Instructions
06490050001 ISSC
What is a programmer?
...an explanation for householders
Programmers allow you to set ‘On’ and ‘Off’ time periods.
Some models switch the central heating and domestic hot
water on and off at the same time, while others allow the
domestic hot water and heating to come on and go off at
different times.
Set the ‘On’ and ‘Off’ time periods to suit your own lifestyle.
On some programmers you must also set whether you want
the heating and hot water to run continuously, run under the
chosen ‘On’ and ‘Off’ heating periods, or be permanently off.
The time on the programmer must be correct. Some types
have to be adjusted in spring and autumn at the changes
between Greenwich Mean Time and British Summer Time.
You may be able to temporarily adjust the heating programme, for example, ‘Override’, ‘Advance’ or ‘Boost’. These
are explained in the manufacturer’s instructions.
The heating will not work if the room thermostat has switched
the heating off. And, if you have a hot-water cylinder, the
water heating will not work if the cylinder thermostat detects
that the hot water has reached the correct temperature.
User’s Instructions
TIMESWITCHES
At the side of the display there are four operating modes:
OFF = continuously off.
TIMED = on for up to 3 periods a day.
ONCE = on for 1 period a day, from the start of ON1
to the end of OFF3.
ON = continuously on.
Use the SELECT button under the flap to change the mode.
This won’t alter the timings in your program, which you can
return to by selecting TIMED.
THE LP111Si 24hr ELECTRONIC TIMESWITCH
LP111Si – a 24hr program, up to 3 heating periods each day,
and every day the same.
Want to leave a timing as it is? Just press SET? and move on
to the next one.
If you need to reset your timings to the standard program
and start again, press ‘SET’ and ‘+’ together to go back to
the pre-set program.
The standard program
Y
our system will come on for up to 3 heating periods every
24hrs. ON1 starts the first one, OFF1 finishes it, and so on.
Notice that ON2 and OFF2 are set to the same time.* This
means your system won’t respond, but if you want to activate
that middle period or change any other timings – read on.
S
WITCHING STANDARD PROGRAM
O
N 1
– start of first timed period 6.30am
OFF 1
– end of first timed period 8.30am
ON 2
– start of second timed period*
OFF 2
– end of second timed period* 12.00 p m
ON 3
– start of third timed period 4.30pm
OFF 3
– final switch-off of the day 10.30pm
Changing the timings
n Press the SET? button and you’ll see ‘SET PROG?’.
DUAL
CHANNEL
SINGLE
CHANNEL
Invensys Controls Europe
S
ales: 0845 1305522 / Technical Helpline: 0845 1307722
Email: customer.care@invensyscontrols.com / Web: www.draytoncontrols.co.uk
User’s Instructions
06490050001 ISSC
What is a programmer?
...an explanation for householders
Programmers allow you to set ‘On’ and ‘Off’ time periods.
S
ome models switch the central heating and domestic hot
water on and off at the same time, while others allow the
domestic hot water and heating to come on and go off at
different times.
Set the ‘On’ and ‘Off’ time periods to suit your own lifestyle.
On some programmers you must also set whether you want
t
he heating and hot water to run continuously, run under the
chosen ‘On’ and ‘Off’ heating periods, or be permanently off.
T
he time on the programmer must be correct. Some types
have to be adjusted in spring and autumn at the changes
between Greenwich Mean Time and British Summer Time.
You may be able to temporarily adjust the heating pro-
g
ramme, for example, ‘Override’, ‘Advance’ or ‘Boost’. These
are explained in the manufacturer’s instructions.
The heating will not work if the room thermostat has switched
the heating off. And, if you have a hot-water cylinder, the
water heating will not work if the cylinder thermostat detects
that the hot water has reached the correct temperature.
User’s Instructions
TIMESWITCHES
W
ant to leave a timing as it is? Just press SET? and move on
to the next one.
If you need to reset your timings to the standard program
and start again, press ‘SET’ and ‘+’ together to go back to
t
he pre-set program.
T
he standard program
Your system will come on for up to 3 heating periods every
2
4hrs. ON1 starts the first one, OFF1 finishes it, and so on.
Notice that ON2 and OFF2 are set to the same time.* This
means your system won’t respond, but if you want to activate
that middle period or change any other timings – read on.
SWITCHING STANDARD PROGRAM
ON 1
– start of first timed period 6.30am
OFF 1
– end of first timed period 8.30am
ON 2
– start of second timed period*
OFF 2
– end of second timed period* 12.00pm
ON 3
– start of third timed period 4.30pm
OFF 3
– final switch-off of the day 10.30pm
Changing the timings
n Press the SET? button and you’ll see ‘SET PROG?’.
n Press the YES button, and you’ll see ON1, the start of your first
heating period. Adjust it in 1-minute steps using the – and +
buttons. If the – and + buttons are held down, the time changes
in 10-minute steps.
n Press SET?, and you’ll see OFF1, the end of your first heating
period. Adjust this in the same way, press SET?, then repeat the
procedure for ON2, OFF2, ON3 and OFF3.
INTRODUCTION
Lifestyle Timeswitches will automatically control your system
by switching it on and off at times that suit you. The red light
on the front of the timeswitch shows when it’s on.
n LP111Si – a 24hr program, up to 3 heating periods
each day, and every day the same.
n LP711Si – a 7-day program, allowing for different
timings on each day of the week, up to 3 heating periods
each day.
If the engineer hasn’t set your timings for you, your timeswitch
will work with a standard program that has been set at the
factory. If this doesn’t suit you, it’s very easy to change it –
when you’ve read this introductory section, simply turn to
the page for your timeswitch model.
water on and off at the same time, while others allow the
domestic hot water and heating to come on and go off at
d
ifferent times.
Set the ‘On’ and ‘Off’ time periods to suit your own lifestyle.
O
n some programmers you must also set whether you want
the heating and hot water to run continuously, run under the
c
hosen ‘On’ and ‘Off’ heating periods, or be permanently off.
T
he time on the programmer must be correct. Some types
have to be adjusted in spring and autumn at the changes
between Greenwich Mean Time and British Summer Time.
Y
ou may be able to temporarily adjust the heating pro-
gramme, for example, ‘Override’, ‘Advance’ or ‘Boost’. These
a
re explained in the manufacturer’s instructions.
The heating will not work if the room thermostat has switched
the heating off. And, if you have a hot-water cylinder, the
w
ater heating will not work if the cylinder thermostat detects
t
hat the hot water has reached the correct temperature.
User’s Instructions
TIMESWITCHES
Notice that ON2 and OFF2 are set to the same time.* This
m
eans your system won’t respond, but if you want to activate
that middle period or change any other timings – read on.
SWITCHING STANDARD PROGRAM
ON 1
– start of first timed period 6.30am
OFF 1
– end of first timed period 8.30am
ON 2
– start of second timed period*
OFF 2
– end of second timed period* 12.00pm
O
N 3
– start of third timed period 4.30pm
OFF 3
– final switch-off of the day 10.30pm
Changing the timings
n Press the SET? button and you’ll see ‘SET PROG?’.
n Press the YES button, and you’ll see ON1, the start of your first
heating period. Adjust it in 1-minute steps using the – and +
buttons. If the – and + buttons are held down, the time changes
in 10-minute steps.
n Press SET?, and you’ll see OFF1, the end of your first heating
period. Adjust this in the same way, press SET?, then repeat the
procedure for ON2, OFF2, ON3 and OFF3.
n When you press SET? after setting OFF3, the timeswitch will
return to normal operation.
THE LP711Si 7-DAY ELECTRONIC TIMESWITCH
LP711Si – a 7-day program, allowing for different
timings on each day of the week, up to 3 heating periods
each day.
Want to leave a timing as it is? Just press SET? and move on
to the next one.
INTRODUCTION
Lifestyle Timeswitches will automatically control your system
by switching it on and off at times that suit you. The red light
on the front of the timeswitch shows when it’s on.
n LP111Si – a 24hr program, up to 3 heating periods
each day, and every day the same.
n LP711Si – a 7-day program, allowing for different
timings on each day of the week, up to 3 heating periods
each day.
If the engineer hasn’t set your timings for you, your timeswitch
will work with a standard program that has been set at the
factory. If this doesn’t suit you, it’s very easy to change it –
when you’ve read this introductory section, simply turn to
the page for your timeswitch model.
Remember:
n Make your changes using the SET?, YES/-, and + buttons.
n You can’t set ON1 as the last timing before midnight, but you
can set OFF3 after midnight – providing it’s not more than 23
hours and 59 minutes after ON1.
n You need to set the timings in sequence – i.e. ON1, OFF1, ON2,
OFF2, ON3, OFF3. If you get out of sequence, the display will
flash a warning.
You may be able to temporarily adjust the heating pro-
g
ramme, for example, ‘Override’, ‘Advance’ or ‘Boost’. These
are explained in the manufacturer’s instructions.
T
he heating will not work if the room thermostat has switched
the heating off. And, if you have a hot-water cylinder, the
water heating will not work if the cylinder thermostat detects
that the hot water has reached the correct temperature.
TIMESWITCHES
OFF 1
– end of first timed period 8.30am
ON 2
– start of second timed period*
12.00pm
OFF 2
– end of second timed period* 12.00pm
ON 3
– start of third timed period 4.30pm
OFF 3
– final switch-off of the day 10 .30pm
Changing the timings
n Press the SET? button and you’ll see ‘SET PROG?’.
n Press the YES button, and you’ll see ON1, the start of your first
heating period. Adjust it in 1-minute steps using the – and +
buttons. If the – and + buttons are held down, the time changes
in 10-minute steps.
n Press SET?, and you’ll see OFF1, the end of your first heating
period. Adjust this in the same way, press SET?, then repeat the
procedure for ON2, OFF2, ON3 and OFF3.
n When you press SET? after setting OFF3, the timeswitch will
return to normal operation.
THE LP711Si 7-DAY ELECTRONIC TIMESWITCH
LP711Si – a 7-day program, allowing for different
timings on each day of the week, up to 3 heating periods
each day.
Want to leave a timing as it is? Just press SET? and move on
to the next one.
If you need to reset your timings to the standard program and
start again, press ‘SET’ and ‘+’ together to go back to the
pre-set program.
The standard program
Your system will come on for up to 3 heating periods every
24hrs. ON1 starts the first one, OFF1 finishes it, and so on.
Notice that ON2 and OFF2 are set to the same time.* This
means your system won’t respond, but if you want to activate
that middle period or change any other timings – read on.
SWITCHING
ON 1
– start of first timed period
OFF 1
– end of first timed period
ON 2
– start of second timed period
OFF 2
– end of second timed period
ON 3
– start of third timed period
OFF 3
– final switch-off of the day
SWITCHING
STANDARD PROGRAM
MON-FRI SAT-SUN
ON 1
– start of first timed period 6.30am 7.00am
OFF 1
– end of first timed period 8.30am 9.0 0a m
ON 2
– start of second timed period* 1 2 . 0 0 p m 12.0 0pm
OFF 2
– end of second timed period* 1 2 . 0 0pm 12 . 00pm
ON 3
– start of third timed period 4.30pm 4.00pm
OFF 3
– final switch-off of the day 10.30pm 11.00 pm
DAY-TO-DAY VARIATIONS Cont...
Over-riding the program
At the side of the display there are four operating modes:
OFF = continuously off.
TIMED = on for up to 3 periods a day.
ONCE = on for 1 period a day, from the start of ON1
to the end of OFF3.
ON = continuously on.
Use the SELECT button under the flap to change the mode.
This won’t alter the timings in your program, which you can
return to by selecting TIMED.
T
HE LP711Si 7-DAY ELECTRONIC TIMESWITCH Cont...
Changing the timings
n Press the SET? button and you’ll see ‘SET PROG?’.
Set all weekdays
First you set the times that are going to be the same for each
weekday, then you can select each day individually and make
any further adjustments. If you want each day to be quite
different, go straight to ‘Set each day’.
n Press the YES button, and the display will ask ‘SET MON to FRI
PROG?’.
n Press YES and you’ll see ON1, the start of your first heating peri-
od. Adjust it in 1-minute steps using the – and + buttons.
DAY-TO-DAY VARIATIONS
Sometimes you might need to change the way you use your
system temporarily – perhaps due to an exceptionally cold day.
Here’s how to do it – without affecting the timings in your
program.
Switching on and off
On the front of the timeswitch is an Advance button. It allows
you to switch your system on or off, irrespective of the program.
Press Advance to switch it on, and it will stay on until the end
of the next OFF period. Turn it off, and it will stay off until the
beginning of the next ON period.
If the engineer has set your program and timings – you won’t
need to do anything else. Just keep this guide in a safe place
for future reference.
SWITCHING
S
TANDARD PROGRAM
MON-FRI SAT-SUN
ON 1
– start of first timed period 6.30am 7.00 am
OFF 1
– end of first timed period 8. 30 a m 9.00 a m
O
N 2
– start of second timed period* 12.00pm 12.0 0 p m
O
FF 2
– end of second timed period* 12.0 0 pm 12. 0 0 pm
ON 3
– start of third timed period 4.30pm 4 .00p m
O
FF 3
– final switch-off of the day 10.30pm 11.00pm
DAY-TO-DAY VARIATIONS Cont...
Over-riding the program
At the side of the display there are four operating modes:
OFF = continuously off.
TIMED = on for up to 3 periods a day.
O
NCE = on for 1 period a day, from the start of ON1
to the end of OFF3.
O
N = continuously on.
U
se the SELECT button under the flap to change the mode.
This won’t alter the timings in your program, which you can
return to by selecting TIMED.
T
HE LP111Si 24hr ELECTRONIC TIMESWITCH
LP111Si – a 24hr program, up to 3 heating periods each day,
and every day the same.
Want to leave a timing as it is? Just press SET? and move on
to the next one.
If you need to reset your timings to the standard program
and start again, press ‘SET’ and ‘+’ together to go back to
the pre-set program.
THE LP711Si 7-DAY ELECTRONIC TIMESWITCH Cont...
Changing the timings
n Press the SET? button and you’ll see ‘SET PROG?’.
S
et all weekdays
First you set the times that are going to be the same for each
weekday, then you can select each day individually and make
any further adjustments. If you want each day to be quite
d
ifferent, go straight to ‘Set each day’.
n Press the YES button, and the display will ask ‘SET MON to FRI
PROG?’.
n Press YES and you’ll see ON1, the start of your first heating peri-
od. Adjust it in 1-minute steps using the – and + buttons.
If the – and + buttons are held down, the time changes in
10-minute steps.
n Press SET?, and you’ll see OFF1, the end of your first heating
period. Adjust this in the same way, press SET?, then repeat
the procedure for ON2, OFF2, ON3 and OFF3.
D
AY-TO-DAY VARIATIONS
S
ometimes you might need to change the way you use your
system temporarily – perhaps due to an exceptionally cold day.
Here’s how to do it – without affecting the timings in your
p
rogram.
Switching on and off
O
n the front of the timeswitch is an Advance button. It allows
you to switch your system on or off, irrespective of the program.
Press Advance to switch it on, and it will stay on until the end
o
f the next OFF period. Turn it off, and it will stay off until the
beginning of the next ON period.
If the engineer has set your program and timings – you won’t
need to do anything else. Just keep this guide in a safe place
for future reference.
SWITCHING
STANDARD PROGRAM
MON-FRI SAT-SUN
ON 1
– start of first timed period 6.30am 7.00 am
O
FF 1
– end of first timed period 8. 30 a m 9.00 a m
ON 2
– start of second timed period* 12.00pm 12.0 0 p m
OFF 2
– end of second timed period* 12.0 0 pm 12. 0 0 pm
ON 3
– start of third timed period 4.30pm 4 .00p m
O
FF 3
– final switch-off of the day 10.30pm 11.00pm
DAY-TO-DAY VARIATIONS Cont...
O
ver-riding the program
A
t the side of the display there are four operating modes:
OFF = continuously off.
T
IMED = on for up to 3 periods a day.
ONCE = on for 1 period a day, from the start of ON1
t
o the end of OFF3.
ON = continuously on.
Use the SELECT button under the flap to change the mode.
This won’t alter the timings in your program, which you can
return to by selecting TIMED.
THE LP111Si 24hr ELECTRONIC TIMESWITCH
LP111Si – a 24hr program, up to 3 heating periods each day,
a
nd every day the same.
Want to leave a timing as it is? Just press SET? and move on
to the next one.
I
f you need to reset your timings to the standard program
and start again, press ‘SET’ and ‘+’ together to go back to
the pre-set program.
The standard program
Your system will come on for up to 3 heating periods every
24hrs. ON1 starts the first one, OFF1 finishes it, and so on.
Notice that ON2 and OFF2 are set to the same time.* This
means your system won’t respond, but if you want to activate
that middle period or change any other timings – read on.
THE LP711Si 7-DAY ELECTRONIC TIMESWITCH Cont...
C
hanging the timings
n Press the SET? button and you’ll see ‘SET PROG?’.
Set all weekdays
F
irst you set the times that are going to be the same for each
w
eekday, then you can select each day individually and make
any further adjustments. If you want each day to be quite
different, go straight to ‘Set each day’.
n
Press the YES button, and the display will ask ‘SET MON to FRI
P
ROG?’.
n Press YES and you’ll see ON1, the start of your first heating peri-
od. Adjust it in 1-minute steps using the – and + buttons.
If the – and + buttons are held down, the time changes in
10-minute steps.
n Press SET?, and you’ll see OFF1, the end of your first heating
p
eriod. Adjust this in the same way, press SET?, then repeat
the procedure for ON2, OFF2, ON3 and OFF3.
Set each day
n If, after you’ve set OFF3 you want to fine-tune one or more
weekdays, press SET? until you find the first day you want to
DAY-TO-DAY VARIATIONS
Sometimes you might need to change the way you use your
system temporarily – perhaps due to an exceptionally cold day.
Here’s how to do it – without affecting the timings in your
program.
S
witching on and off
On the front of the timeswitch is an Advance button. It allows
you to switch your system on or off, irrespective of the program.
P
ress Advance to switch it on, and it will stay on until the end
of the next OFF period. Turn it off, and it will stay off until the
beginning of the next ON period.
If the engineer has set your program and timings – you won’t
need to do anything else. Just keep this guide in a safe place
for future reference.
D
AY-TO-DAY VARIATIONS Cont...
Over-riding the program
At the side of the display there are four operating modes:
OFF = continuously off.
TIMED = on for up to 3 periods a day.
O
NCE = on for 1 period a day, from the start of ON1
to the end of OFF3.
ON = continuously on.
U
se the SELECT button under the flap to change the mode.
This won’t alter the timings in your program, which you can
return to by selecting TIMED.
T
HE LP111Si 24hr ELECTRONIC TIMESWITCH
LP111Si – a 24hr program, up to 3 heating periods each day,
and every day the same.
W
ant to leave a timing as it is? Just press SET? and move on
to the next one.
If you need to reset your timings to the standard program
and start again, press ‘SET’ and ‘+’ together to go back to
the pre-set program.
The standard program
Your system will come on for up to 3 heating periods every
24hrs. ON1 starts the first one, OFF1 finishes it, and so on.
Notice that ON2 and OFF2 are set to the same time.* This
means your system won’t respond, but if you want to activate
that middle period or change any other timings – read on.
SWITCHING STANDARD PROGRAM
ON 1
– start of first timed period 6. 30a m
OFF 1
– end of first timed period 8. 30 a m
ON 2
– start of second timed period*
12.00pm
OFF 2
– end of second timed period* 12.00pm
ON 3
– start of third timed period 4.30pm
OFF 3
– final switch-off of the day 10.30pm
Changing the timings
n Press the SET? button and you’ll see ‘SET PROG?’.
PROG?
Changing the timings
n Press the SET? button and you’ll see ‘SET PROG?’.
S
et all weekdays
First you set the times that are going to be the same for each
weekday, then you can select each day individually and make
any further adjustments. If you want each day to be quite
d
ifferent, go straight to ‘Set each day’.
n Press the YES button, and the display will ask ‘SET MON to FRI
PROG?’.
n Press YES and you’ll see ON1, the start of your first heating peri-
od. Adjust it in 1-minute steps using the – and + buttons.
If the – and + buttons are held down, the time changes in
1
0-minute steps.
n Press SET?, and you’ll see OFF1, the end of your first heating
period. Adjust this in the same way, press SET?, then repeat
the procedure for ON2, OFF2, ON3 and OFF3.
Set each day
n If, after you’ve set OFF3 you want to fine-tune one or more
weekdays, press SET? until you find the first day you want to
adjust – then go through the procedure, altering any time you
wish. Press SET? to move on to the next day. When you’ve
finished, press SET? until you see ‘SET SAT SUN PROG?’.
n If you don’t want to alter any individual days, keep pressing
SET? until you see ‘SET SAT SUN PROG?’.
Set weekend
n Press YES and alter ON1, OFF1, ON2, OFF2, ON3 and OFF3
times in the same way.
y
ou to switch your system on or off, irrespective of the program.
Press Advance to switch it on, and it will stay on until the end
of the next OFF period. Turn it off, and it will stay off until the
beginning of the next ON period.
At the side of the display there are four operating modes:
OFF = continuously off.
TIMED = on for up to 3 periods a day.
ONCE = on for 1 period a day, from the start of ON1
t
o the end of OFF3.
ON = continuously on.
Use the SELECT button under the flap to change the mode.
T
his won’t alter the timings in your program, which you can
return to by selecting TIMED.
THE LP111Si 24hr ELECTRONIC TIMESWITCH
L
P111Si – a 24hr program, up to 3 heating periods each day,
and every day the same.
W
ant to leave a timing as it is? Just press SET? and move on
to the next one.
If you need to reset your timings to the standard program
and start again, press ‘SET’ and ‘+’ together to go back to
t
he pre-set program.
The standard program
Your system will come on for up to 3 heating periods every
24hrs. ON1 starts the first one, OFF1 finishes it, and so on.
Notice that ON2 and OFF2 are set to the same time.* This
means your system won’t respond, but if you want to activate
that middle period or change any other timings – read on.
SWITCHING STANDARD PROGRAM
ON 1
– start of first timed period 6. 30a m
OFF 1
– end of first timed period 8. 30 a m
ON 2
– start of second timed period*
12.00pm
OFF 2
– end of second timed period* 12.00pm
ON 3
– start of third timed period 4.30pm
OFF 3
– final switch-off of the day 10.30pm
Changing the timings
n Press the SET? button and you’ll see ‘SET PROG?’.
n Press the YES button, and you’ll see ON1, the start of your first
heating period. Adjust it in 1-minute steps using the – and +
buttons. If the – and + buttons are held down, the time changes
in 10-minute steps.
F
irst you set the times that are going to be the same for each
weekday, then you can select each day individually and make
any further adjustments. If you want each day to be quite
different, go straight to ‘Set each day’.
n
Press the YES button, and the display will ask ‘SET MON to FRI
PROG?’.
n
Press YES and you’ll see ON1, the start of your first heating peri-
od. Adjust it in 1-minute steps using the – and + buttons.
If the – and + buttons are held down, the time changes in
10-minute steps.
n Press SET?, and you’ll see OFF1, the end of your first heating
period. Adjust this in the same way, press SET?, then repeat
t
he procedure for ON2, OFF2, ON3 and OFF3.
Set each day
n If, after you’ve set OFF3 you want to fine-tune one or more
weekdays, press SET? until you find the first day you want to
adjust – then go through the procedure, altering any time you
wish. Press SET? to move on to the next day. When you’ve
finished, press SET? until you see ‘SET SAT SUN PROG?’.
n If you don’t want to alter any individual days, keep pressing
SET? until you see ‘SET SAT SUN PROG?’.
Set weekend
n Press YES and alter ON1, OFF1, ON2, OFF2, ON3 and OFF3
times in the same way.
Set each day
n If, after you’ve set OFF3 for both SAT & SUN, you want to fine-
tune Saturday or Sunday, press SET? until you find the first day
you want to adjust – then go through the procedure, altering any
time you wish. Press SET? to move on to the next day. When
you press SET? after setting your hot water for Sundays, the pro-
grammer will go back to normal operation.
ON = continuously on.
Use the SELECT button under the flap to change the mode.
T
his won’t alter the timings in your program, which you can
return to by selecting TIMED.
THE LP111Si 24hr ELECTRONIC TIMESWITCH
L
P111Si – a 24hr program, up to 3 heating periods each day,
and every day the same.
Want to leave a timing as it is? Just press SET? and move on
to the next one.
If you need to reset your timings to the standard program
and start again, press ‘SET’ and ‘+’ together to go back to
the pre-set program.
The standard program
Your system will come on for up to 3 heating periods every
24hrs. ON1 starts the first one, OFF1 finishes it, and so on.
Notice that ON2 and OFF2 are set to the same time.* This
means your system won’t respond, but if you want to activate
that middle period or change any other timings – read on.
SWITCHING STANDARD PROGRAM
ON 1
– start of first timed period 6. 30a m
OFF 1
– end of first timed period 8. 30 a m
ON 2
– start of second timed period*
12.00pm
OFF 2
– end of second timed period* 12.00pm
ON 3
– start of third timed period 4.30pm
OFF 3
– final switch-off of the day 10.30pm
Changing the timings
n Press the SET? button and you’ll see ‘SET PROG?’.
n Press the YES button, and you’ll see ON1, the start of your first
heating period. Adjust it in 1-minute steps using the – and +
buttons. If the – and + buttons are held down, the time changes
in 10-minute steps.
n Press SET?, and you’ll see OFF1, the end of your first heating
period. Adjust this in the same way, press SET?, then repeat the
procedure for ON2, OFF2, ON3 and OFF3.
n
Press YES and you’ll see ON1, the start of your first heating peri-
od. Adjust it in 1-minute steps using the – and + buttons.
If the – and + buttons are held down, the time changes in
10-minute steps.
n Press SET?, and you’ll see OFF1, the end of your first heating
period. Adjust this in the same way, press SET?, then repeat
the procedure for ON2, OFF2, ON3 and OFF3.
Set each day
n If, after you’ve set OFF3 you want to fine-tune one or more
weekdays, press SET? until you find the first day you want to
adjust – then go through the procedure, altering any time you
wish. Press SET? to move on to the next day. When you’ve
finished, press SET? until you see ‘SET SAT SUN PROG?’.
n If you don’t want to alter any individual days, keep pressing
SET? until you see ‘SET SAT SUN PROG?’.
Set weekend
n Press YES and alter ON1, OFF1, ON2, OFF2, ON3 and OFF3
times in the same way.
Set each day
n If, after you’ve set OFF3 for both SAT & SUN, you want to fine-
tune Saturday or Sunday, press SET? until you find the first day
you want to adjust – then go through the procedure, altering any
time you wish. Press SET? to move on to the next day. When
you press SET? after setting your hot water for Sundays, the pro-
grammer will go back to normal operation.
n If you don’t want to alter either day, keep pressing SET?
until the programmer goes back to normal operation.
User’s Instructions
r
eturn to by selecting TIMED.
THE LP111Si 24hr ELECTRONIC TIMESWITCH
LP111Si – a 24hr program, up to 3 heating periods each day,
and every day the same.
Want to leave a timing as it is? Just press SET? and move on
t
o the next one.
If you need to reset your timings to the standard program
and start again, press ‘SET’ and ‘+’ together to go back to
the pre-set program.
The standard program
Your system will come on for up to 3 heating periods every
24hrs. ON1 starts the first one, OFF1 finishes it, and so on.
Notice that ON2 and OFF2 are set to the same time.* This
means your system won’t respond, but if you want to activate
that middle period or change any other timings – read on.
SWITCHING STANDARD PROGRAM
ON 1
– start of first timed period 6. 30a m
OFF 1
– end of first timed period 8. 30 a m
ON 2
– start of second timed period*
12.00pm
OFF 2
– end of second timed period* 12.00pm
ON 3
– start of third timed period 4.30pm
OFF 3
– final switch-off of the day 10.30pm
Changing the timings
n Press the SET? button and you’ll see ‘SET PROG?’.
n Press the YES button, and you’ll see ON1, the start of your first
heating period. Adjust it in 1-minute steps using the – and +
buttons. If the – and + buttons are held down, the time changes
in 10-minute steps.
n Press SET?, and you’ll see OFF1, the end of your first heating
period. Adjust this in the same way, press SET?, then repeat the
procedure for ON2, OFF2, ON3 and OFF3.
n When you press SET? after setting OFF3, the timeswitch will
return to normal operation.
n Press YES and you’ll see ON1, the start of your first heating peri-
o
d. Adjust it in 1-minute steps using the – and + buttons.
If the – and + buttons are held down, the time changes in
10-minute steps.
n
Press SET?, and you’ll see OFF1, the end of your first heating
period. Adjust this in the same way, press SET?, then repeat
the procedure for ON2, OFF2, ON3 and OFF3.
Set each day
n If, after you’ve set OFF3 you want to fine-tune one or more
weekdays, press SET? until you find the first day you want to
adjust – then go through the procedure, altering any time you
wish. Press SET? to move on to the next day. When you’ve
finished, press SET? until you see ‘SET SAT SUN PROG?’.
n If you don’t want to alter any individual days, keep pressing
SET? until you see ‘SET SAT SUN PROG?’.
Set weekend
n Press YES and alter ON1, OFF1, ON2, OFF2, ON3 and OFF3
times in the same way.
Set each day
n If, after you’ve set OFF3 for both SAT & SUN, you want to fine-
tune Saturday or Sunday, press SET? until you find the first day
you want to adjust – then go through the procedure, altering any
time you wish. Press SET? to move on to the next day. When
you press SET? after setting your hot water for Sundays, the pro-
grammer will go back to normal operation.
n If you don’t want to alter either day, keep pressing SET?
until the programmer goes back to normal operation.
S
Over-riding the program
User’s Instructions
PROGRAMMERS
a
nd start again, press ‘SET’ and ‘+’ together to go back to
t
he pre-set program.
The standard program
Your system will come on for up to 3 heating periods every
24hrs. ON1 starts the first one, OFF1 finishes it, and so on.
Notice that ON2 and OFF2 are set to the same time.* This
means your system won’t respond, but if you want to activate
that middle period or change any other timings – read on.
SWITCHING STANDARD PROGRAM
ON 1
– start of first timed period 6.30am
O
FF 1
– end of first timed period 8.30am
ON 2
– start of second timed period*
12.00pm
OFF 2
– end of second timed period* 12.00pm
ON 3
– start of third timed period 4.30pm
OFF 3
– final switch-off of the day 10.30pm
Changing the timings
n Press the SET? button and you’ll see ‘SET PROG?’.
n Press the YES button, and you’ll see ON1, the start of your first
heating period. Adjust it in 1-minute steps using the – and +
buttons. If the – and + buttons are held down, the time changes
in 10-minute steps.
n Press SET?, and you’ll see OFF1, the end of your first heating
period. Adjust this in the same way, press SET?, then repeat the
procedure for ON2, OFF2, ON3 and OFF3.
n
When you press SET? after setting OFF3, the timeswitch will
r
eturn to normal operation.
THE LP711Si 7-DAY ELECTRONIC TIMESWITCH
LP711Si – a 7-day program, allowing for different
timings on each day of the week, up to 3 heating periods
each day.
Want to leave a timing as it is? Just press SET? and move on
to the next one.
If you need to reset your timings to the standard program and
start again, press ‘SET’ and ‘+’ together to go back to the
pre-set program.
period. Adjust this in the same way, press SET?, then repeat
the procedure for ON2, OFF2, ON3 and OFF3.
S
et each day
n
If, after you’ve set OFF3 you want to fine-tune one or more
w
eekdays, press SET? until you find the first day you want to
a
djust – then go through the procedure, altering any time you
w
ish. Press SET? to move on to the next day. When you’ve
f
inished, press SET? until you see ‘SET SAT SUN PROG?’.
n If you don’t want to alter any individual days, keep pressing
SET? until you see ‘SET SAT SUN PROG?’.
Set weekend
n Press YES and alter ON1, OFF1, ON2, OFF2, ON3 and OFF3
times in the same way.
Set each day
n If, after you’ve set OFF3 for both SAT & SUN, you want to fine-
tune Saturday or Sunday, press SET? until you find the first day
you want to adjust – then go through the procedure, altering any
time you wish. Press SET? to move on to the next day. When
you press SET? after setting your hot water for Sundays, the pro-
grammer will go back to normal operation.
n If you don’t want to alter either day, keep pressing SET?
until the programmer goes back to normal operation.
If the engineer has set your program and timings – you
won’t need to do anything else. Just keep this guide in a
safe place for future reference.
INTRODUCTION
Lifestyle Programmers will automatically switch your central
heating and hot water on and off at times that suit you.
Depending on your system, central heating and hot water
Switching on and off
O
User’s Instructions
PROGRAMMERS
m
eans your system won’t respond, but if you want to activate
t
hat middle period or change any other timings – read on.
SWITCHING STANDARD PROGRAM
ON 1
– start of first timed period 6.30am
OFF 1
– end of first timed period 8.30am
ON 2
– start of second timed period*
12.00pm
O
FF 2
– end of second timed period* 12.00pm
O
N 3
– start of third timed period 4.30pm
O
FF 3
– final switch-off of the day 10.30pm
Changing the timings
n Press the SET? button and you’ll see ‘SET PROG?’.
n
Press the YES button, and you’ll see ON1, the start of your first
h
eating period. Adjust it in 1-minute steps using the – and +
b
uttons. If the – and + buttons are held down, the time changes
i
n 10-minute steps.
n Press SET?, and you’ll see OFF1, the end of your first heating
period. Adjust this in the same way, press SET?, then repeat the
procedure for ON2, OFF2, ON3 and OFF3.
n When you press SET? after setting OFF3, the timeswitch will
return to normal operation.
THE LP711Si 7-DAY ELECTRONIC TIMESWITCH
LP711Si – a 7-day program, allowing for different
timings on each day of the week, up to 3 heating periods
each day.
Want to leave a timing as it is? Just press SET? and move on
to the next one.
I
f you need to reset your timings to the standard program and
s
tart again, press ‘SET’ and ‘+’ together to go back to the
p
re-set program.
The standard program
Your system will come on for up to 3 heating periods every
24hrs. ON1 starts the first one, OFF1 finishes it, and so on.
Notice that ON2 and OFF2 are set to the same time.* This
means your system won’t respond, but if you want to activate
that middle period or change any other timings – read on.
n If, after you’ve set OFF3 you want to fine-tune one or more
weekdays, press SET? until you find the first day you want to
adjust – then go through the procedure, altering any time you
wish. Press SET? to move on to the next day. When you’ve
finished, press SET? until you see ‘SET SAT SUN PROG?’.
n If you don’t want to alter any individual days, keep pressing
SET? until you see ‘SET SAT SUN PROG?’.
Set weekend
n
Press YES and alter ON1, OFF1, ON2, OFF2, ON3 and OFF3
t
imes in the same way.
S
et each day
n
If, after you’ve set OFF3 for both SAT & SUN, you want to fine-
t
une Saturday or Sunday, press SET? until you find the first day
y
ou want to adjust – then go through the procedure, altering any
t
ime you wish. Press SET? to move on to the next day. When
y
ou press SET? after setting your hot water for Sundays, the pro-
g
rammer will go back to normal operation.
n If you don’t want to alter either day, keep pressing SET?
until the programmer goes back to normal operation.
If the engineer has set your program and timings – you
won’t need to do anything else. Just keep this guide in a
safe place for future reference.
INTRODUCTION
Lifestyle Programmers will automatically switch your central
heating and hot water on and off at times that suit you.
Depending on your system, central heating and hot water
can either both come on and off at the same time, or work
independently. The red light on the front of the programmer
shows when each one is on.
INTRODUCTION Cont...
There are 3 models in the Lifestyle range:
n LP241Si – a 24hr program, with central heating and hot water
working independently for up to 3 heating periods each day, and
every day the same.
n LP522Si – a 5/2-day program allowing for different timings at
the weekends, with central heating and hot water working
independently for up to 3 heating periods each day.
n LP722Si – a 7-day program allowing for different timings on
each day of the week, with central heating and hot water
working independently for up to 3 heating periods each day.
SWITCHING
STANDARD PROGRAM
MON-FRI SAT-SUN
ON 1
– start of first timed period 6.30am 7.00am
OFF 1
– end of first timed period 8 .3 0 am 9.00am
ON 2
– star t of second timed period* 12.00pm 1 2 . 0 0 p m
OFF 2
– end of second timed period* 12.0 0 p m 12.00 p m
ON 3
– start of third timed period 4. 30pm 4.00pm
OFF 3
– final switch-off of the day 10.30pm 11.00pm
THE LP711Si 7-DAY ELECTRONIC TIMESWITCH Cont...
INTRODUCTION Cont...
There are 3 models in the Lifestyle range:
n LP241Si – a 24hr program, with central heating and hot water
working independently for up to 3 heating periods each day, and
every day the same.
n LP522Si – a 5/2-day program allowing for different timings at
the weekends, with central heating and hot water working
independently for up to 3 heating periods each day.
n LP722Si – a 7-day program allowing for different timings on
each day of the week, with central heating and hot water
working independently for up to 3 heating periods each day.
If the engineer hasn’t set your timings for you, your programmer
will work with a standard program that has been set at the
factory. If this doesn’t suit you, it’s very easy to change it –
SWITCHING
STANDARD PROGRAM
MON-FRI SAT-SUN
ON 1
– start of first timed period 6.30am 7.00am
OFF 1
– end of first timed period 8 .3 0 am 9.00am
ON 2
– star t of second timed period* 12.00pm 1 2 . 0 0 p m
OFF 2
– end of second timed period* 12.0 0 p m 12.00 p m
ON 3
– start of third timed period 4. 30pm 4.00pm
OFF 3
– final switch-off of the day 10.30pm 11.00pm
THE LP711Si 7-DAY ELECTRONIC TIMESWITCH Cont...
Changing the timings
n Press the SET? button and you’ll see ‘SET PROG?’.
INTRODUCTION Cont...
There are 3 models in the Lifestyle range:
n LP241Si – a 24hr program, with central heating and hot water
working independently for up to 3 heating periods each day, and
every day the same.
n LP522Si – a 5/2-day program allowing for different timings at
the weekends, with central heating and hot water working
independently for up to 3 heating periods each day.
n LP722Si – a 7-day program allowing for different timings on
each day of the week, with central heating and hot water
working independently for up to 3 heating periods each day.
If the engineer hasn’t set your timings for you, your programmer
will work with a standard program that has been set at the
factory. If this doesn’t suit you, it’s very easy to change it –
when you’ve read this introductory section, simply go to the
section that contains your programmer model.
Remember:
n Make your changes using the SET?, YES/-, and + buttons on
the programmer.
n You can’t set ON1 as the last timing before midnight, but you
can set OFF3 after midnight – providing it’s not more than 23
hours and 59 minutes after ON1.
SWITCHING
STANDARD PROGRAM
MON-FRI SAT-SUN
ON 1
– start of first timed period 6.30am 7.00am
OFF 1
– end of first timed period 8 .3 0 am 9.00am
ON 2
– star t of second timed period* 12.00pm 1 2 . 0 0 p m
OFF 2
– end of second timed period* 12.0 0 p m 12.00 p m
ON 3
– start of third timed period 4. 30pm 4.00pm
OFF 3
– final switch-off of the day 10.30pm 11.00pm
THE LP711Si 7-DAY ELECTRONIC TIMESWITCH Cont...
Changing the timings
n Press the SET? button and you’ll see ‘SET PROG?’.
Set all weekdays
First you set the times that are going to be the same for each
weekday, then you can select each day individually and make
any further adjustments. If you want each day to be quite
different, go straight to ‘Set each day’.
n Press the YES button, and the display will ask ‘SET MON to FRI
PROG?’.
PROG?
INTRODUCTION Cont...
There are 3 models in the Lifestyle range:
n LP241Si – a 24hr program, with central heating and hot water
working independently for up to 3 heating periods each day, and
every day the same.
n LP522Si – a 5/2-day program allowing for different timings at
the weekends, with central heating and hot water working
independently for up to 3 heating periods each day.
n LP722Si – a 7-day program allowing for different timings on
each day of the week, with central heating and hot water
working independently for up to 3 heating periods each day.
If the engineer hasn’t set your timings for you, your programmer
will work with a standard program that has been set at the
factory. If this doesn’t suit you, it’s very easy to change it –
when you’ve read this introductory section, simply go to the
section that contains your programmer model.
Remember:
n Make your changes using the SET?, YES/-, and + buttons on
the programmer.
n You can’t set ON1 as the last timing before midnight, but you
can set OFF3 after midnight – providing it’s not more than 23
hours and 59 minutes after ON1.
n You need to set the timings in sequence – i.e. ON1, OFF1, ON2,
OFF2, ON3, OFF3. If you get out of sequence, the display will
flash a warning.
SWITCHING
STANDARD PROGRAM
MON-FRI SAT-SUN
ON 1
– start of first timed period 6.30am 7.00am
OFF 1
– end of first timed period 8 .3 0 am 9.00am
ON 2
– star t of second timed period* 12.00pm 1 2 . 0 0 p m
OFF 2
– end of second timed period* 12.0 0 p m 12.00 p m
ON 3
– start of third timed period 4. 30pm 4.00pm
OFF 3
– final switch-off of the day 10.30pm 11.00pm
THE LP711Si 7-DAY ELECTRONIC TIMESWITCH Cont...
Changing the timings
n Press the SET? button and you’ll see ‘SET PROG?’.
Set all weekdays
First you set the times that are going to be the same for each
weekday, then you can select each day individually and make
any further adjustments. If you want each day to be quite
different, go straight to ‘Set each day’.
n Press the YES button, and the display will ask ‘SET MON to FRI
PROG?’.
PROG?
MON TUE WED THU FRI
INTRODUCTION Cont...
There are 3 models in the Lifestyle range:
n LP241Si – a 24hr program, with central heating and hot water
working independently for up to 3 heating periods each day, and
every day the same.
n LP522Si – a 5/2-day program allowing for different timings at
the weekends, with central heating and hot water working
independently for up to 3 heating periods each day.
n LP722Si – a 7-day program allowing for different timings on
each day of the week, with central heating and hot water
working independently for up to 3 heating periods each day.
If the engineer hasn’t set your timings for you, your programmer
will work with a standard program that has been set at the
factory. If this doesn’t suit you, it’s very easy to change it –
when you’ve read this introductory section, simply go to the
section that contains your programmer model.
Remember:
n Make your changes using the SET?, YES/-, and + buttons on
the programmer.
n You can’t set ON1 as the last timing before midnight, but you
can set OFF3 after midnight – providing it’s not more than 23
hours and 59 minutes after ON1.
n You need to set the timings in sequence – i.e. ON1, OFF1, ON2,
OFF2, ON3, OFF3. If you get out of sequence, the display will
flash a warning.
SWITCHING
ON 1
– start of first timed period
OFF 1
– end of first timed period
SWITCHING
STANDARD PROGRAM
MON-FRI SAT-SUN
ON 1
– start of first timed period 6.30am 7.00am
OFF 1
– end of first timed period 8 .3 0 am 9.00am
ON 2
– star t of second timed period* 12.00pm 1 2 . 0 0 p m
OFF 2
– end of second timed period* 12.0 0 p m 12.00 p m
ON 3
– start of third timed period 4. 30pm 4.00pm
OFF 3
– final switch-off of the day 10.30pm 11.00pm
THE LP711Si 7-DAY ELECTRONIC TIMESWITCH Cont...
Changing the timings
n Press the SET? button and you’ll see ‘SET PROG?’.
Set all weekdays
First you set the times that are going to be the same for each
weekday, then you can select each day individually and make
any further adjustments. If you want each day to be quite
different, go straight to ‘Set each day’.
n Press the YES button, and the display will ask ‘SET MON to FRI
PROG?’.
n Press YES and you’ll see ON1, the start of your first heating peri-
od. Adjust it in 1-minute steps using the – and + buttons.
If the – and + buttons are held down, the time changes in
10-minute steps.
Loading...