Drayton RF701, 22092, Digistat +3RF RF701/22092 User Manual

Drayton

Digistat +3RF

Invensys Controls Europe

Customer Service Tel: [phone]
Customer Service Fax: [phone]
Technical Helpline Tel: [phone]
Website: www

.draytoncontrols.co.uk

Email: [e-mail]

User Guide 06490098001 IssA

Programmable Room
Thermostat Wireless

5-2 Day / 7 Day

Model: RF701/22092

Power Supply:

Battery - Thermostat
Mains - Digistat SCR

T

Certification Mark

The Digistat +3RF thermostat is a programmable thermostat
5-2 Day / 7 Day product. 5–2 day allows you to set a program for
weekdays and a program for the weekend. Full 7-day functionality
allows you to set a different program for every day of the week.
Each program type allows you to set 6 time and temperature events.

Clock Setting

Your Digistat +3RF is fitted with a real-time clock, which is pre-set
at the factory. You will not have to alter the time settings.
A special feature of this real-time clock is to automatically update
the time during the summer/winter time change removing the
need to manually alter the clock.

General Operation

With the unit in Auto mode (the small arrow to bottom of screen
will point to Auto) the temperature can be changed for a short
time by using the + or - buttons. Changing the temperature in
this way will keep the Digistat +3RF set to your new temperature
until the next pre-programmed event (at which time it will revert
to programmed temperature). The temperature you are setting
will flash on the screen. Once temperature is set, the unit will
revert to showing the current temperature. The indicator will
show on the screen if the heating is turned on.

Your Digistat +3RF

Controls and Display Layout

Drayton

Digistat +3RF

A flashing flame indicates the product is in intelligent delayed
start mode (see special note).

How to replace the batteries see fig 3.

Remove the battery cover using a coin. Replace the spent
batteries with 2 x 1.5V IEC LR6 (AA) Alkaline batteries

ensuring

correct orientation. Replace the battery cover pressing fully home.

(Fig 1) (Fig 2)

How do I know when to change the batteries.

W

hen the batteries start to run low a battery icon will flash in the

d

isplay, to indicate “low battery” during this time the Digistat +3RF

will function normally (see fig 1).
Please replace batteries with 2 x 1.5V IEC LR6 (AA) Alkaline batteries.
When the battery icon alone is shown in the display, the batteries
are completely exhausted and the Digistat +3RF will cease to
function (see fig 2). Re-activate by replacing the batteries.

The Digistat +3RF thermostat is a programmable thermostat
5-2 Day / 7 Day product. 5–2 day allows you to set a program for
weekdays and a program for the weekend. Full 7-day functionality
allows you to set a different program for every day of the week.
Each program type allows you to set 6 time and temperature events.

Basic Settings

(Fig 3)

D

igis

ta

t

+

3

RF

D

i

g

i

s

ta

t

+

3

R

F

D

r

a

y

t

o

n

D

r

a

y

t

o

n

D

r

a

y

t

o

n

D

i

g

i

s

t

a

t

+3

R

F

D

i

g

i

s

t

a

t

+

3

R

F

D

r

a

y

t

o

n

Digistat +3RF
Pre-set Program

Your Digistat +3RF comes with the following default settings
pre-programmed for your convenience:

Event 1 2 3 4 5 6

Time 6:30 8:30 12:00 14:00 16:30 22:30

Temperature 20.0 16.0 16.0 16.0 21.0 7.0

Event 1 2 3 4 5 6

Time 7:00 9:00 12:00 14:00 16:00 23:00

Temperature 20.0 18.0 21.0 18.0 21.0 7.0

123456

25ºC

20ºC

15ºC

10ºC

5ºC

06:30 08:30 12:00 14:00 16:30 22:30

Time Period Monday-Friday

Room Temp

123456

25ºC

20ºC

15ºC

10ºC

5ºC

07:00 09:00 12:00 14:00 16:00 23:00

Time Period Saturday-Sunday

Room Temp

Pre-set Program 1 (9 til 5)

Monday-Friday

Saturday-Sunday

Weekday

Weekend

As you can see, at 06:30 , the heating will come on to raise the
temperature to 20ºC. At 08:30, the temperature set point is dropped
from 20ºC down to16ºC, it stays at 16ºC throughout the day, until
16:30 when the temperature increases to 21ºC. The temperature
then drops down to a night-setback temperature of 7ºC until 06:30
when the cycle repeats for the next day. (Monday to Friday) or
changes to weekend setting see below.

As you can see, at 07:00, the heating will come on to raise the
temperature to 20ºC. At 09:00, the temperature set point is
dropped from 20ºC down to18ºC, it stays at 18ºC until 12:00 when
the heating comes on to raise the temperature to 21ºC. The
temperature stays at 21ºC until 14:00 when it drops down to 18ºC.
At 16:30 the heating comes on to raise the temperature to 21ºC
where it stays until 23:00 when the temperature then drops down
to a night-setback temperature of 7ºC until 07:00 when the cycle
repeats for the next day. (Saturday and Sunday) or changes to
weekday settings see above.

To adjust the times and temperatures for 5-2 Day
operation:

2. Press the once, the
display will be as shown. The
time will be flashing, use the
+ or - buttons to adjust the
1st time as required.

3. Once time has been set,
press and use the
+ or - button to adjust
required temperature
(shown flashing).
Press to confirm and
move to the next time and
temperature periods to be
adjusted confirming changes
by pressing button.
(max 6 periods).

4. Once the last weekday
temperature has been set
press once to confirm
settings and allow adjustment
of the weekend program.
Use the + and – butons and
the button to set the 6
periods for the weekend program.

5. Once the final temperature
has been set press to
confirm setting. To exit press

or until you
return to auto mode with the
bottom arrow pointing at Auto.

(* small 1 in lower half of screen

shows which time period is being set

e.g. 1=1st period, 2 = 2nd period etc)

Congratulations!

The unit is now set correctly to follow your required timings.

1

. With the product operating

as normal in the Auto mode
press once and then
press the + button until the
display is flashing and shows.