Drayton Digistat+ 3 22087 Installation Manual

continued–

GuideInstallation

Day Auto ManHol

96.5

.331

137.0

Dataechnical T

2208722083Model

50HzAC 230V 1.5V AA X 2 supplyower P

batteriesalkaline

–typicalyears 3 lifeBattery

ratingSwitch

caV230 16(2)A N.O.)(switch Heating

contacts)free (voltage SPDT typeSwitch

(inductive)ac @24V10mA currentrecommended Min.

0°C5o t0°C Operating temperatureAmbient

5°C8to 20°C – Storage

85%to 25% Operating humidityAmbient

95%to 15% Storage condensing).(non

2°C3to 0°C rangeemperature T

.5°C0)C°2 3 &C°7(between Accuracy

minute 1resolutionTiming

.1°C0resolutionemperature T

2.5KVvoltageimpulse Rated

75°Ctestpressure Ball

2Degree situationollution P

IP30levelProtection

, onlywiring fixed for Designed :Wiring

regulationswiring IEE with omply cto

Dimensions

Options.Installer

shownas Options Installer the of any change to wish you If

byode mAuto from Menu Option Installer the enter ,below

seconds.5 for simultaneously + and < pressing

andMenu the exit will seconds 5 for again + and < Pressing

ode. mAuto to return

the8), (Fig selected been has screen Options Installer the Once

(shownMenu the through scroll to you allow buttons > and <

valuea Once values. change to you allow - and + The below).

savewill Menu the exiting before > pressing changed been has

OFF).1 Option shows 9 (Fig setting. new the

9)(Fig

lock.protection Access

theock lto installer the allows lock protection access The

adjustments.any make cannot user the that so Digistat+3

theadjust to users the allowing mode OFF is default The

Guide).User (see Digistat+3

MenuOptions Installer the enter settings Digistat+3the ock Lo T

.acceptto > press and On select and 1) Option Installer to efer (R

bewill buttons all exited is Menu Options Installer the Once

andMenu Installer the enter Lock Protection the off switch o T

.acceptto > Press . OFFto change

.adjustto free be will buttons all exited is Menu Installer the Once

protection.Freeze

roomthe if heating the on switch will protection Freeze

attemperature the control then will and 5ºC to falls temperature

mode.OFF in is Digistat+3the if even 7ºC

ON.is default protection freeze The

Installerthe enter mode protection Freeze the off switch o T

.OFFto change and 2) Options Installer to efer (RMenu Options

.acceptto > Press

points.set Limit High nd aLow

Lowand 32ºC High are defaults points set temperature user The

MenuOptions Installer the enter limits these change to 7ºC,

4).& 3 Options Installer to efer (R

feature).saving (Energy Start Delayed Intelligent

whichfeature saving energy an is Start Delayed Intelligent The

system.heating the for time up warm the reduces automatically

thedelay will Start Intelligent , milderbecomes weather the As

roomthe bringing wasted not is fuel that so times start heating

.necessarythan earlier temperature to up

ode.mAuto in applies only Start Delayed Intelligent Note:

mode.OFF in is default Start Delayed Intelligent

OptionsInstaller the enter Start Delayed Intelligent on switch o T

5).Options Installer to efer (RMenu
forsuitable not is option start Delayed Intelligent the Note

application.underfloor Hydronic

commissioningfinal before Off to set is 5 option Installer Ensure

application.underfloor Hydronic for

torequirement a be may there systems heating hydronic some In

periodgiven a for , daya once it operating by valve the protect

system. heating the on bringing without

afor operated be will valve the selected is protection valve If

(mins).time protection alve Vin shown as period

10.00am.at day every time protection alve V

.OFFis default protection alve V

OptionsInstaller the enter mode protection valve the enable o T

6)Option Installer to efer (RMenu

(mins).time protection alve V

minutes5 and 1 between set be can time protection alve V

minutes)3 (default

OptionsInstaller the enter time on day a once this change o T

7).Option Installer to efer (RMenu

DefaultbetweenSelect itis What Options

OffOffOnlock protection Access 1
OnOffnOprotectionFreeze 2
7limitHigh 7ºCpoint set limit ow L3
3232limitLow ºC point set limit High 4

start Delayed 5

OffOffOnfeature)saving (Energy
OffOffnOprotectionalve V6
351(Mins)time protection alve V7
OffOffnOfunctionfault Sensor 8
001typeApplication 9

function.ault fSensor

indicatesthis (E2) or (E1) code error an shows display the When

willsystem heating the and fault sensor a

.Offremain

.sensorexternal = (E2) and sensor internal = (E1)

replaced. be should Digistat+3the shown is (E1) If

blockterminal sensor external the check first shown, is (E2) If

.Digistat+3the replacing before connections

Digistat+3the set temporally to you allows function fault Sensor

haveyou until Off 70% and On 30% system heating the cycle to

.productthe replaced

(OptionMenu Option installer the entering by done be can This

.acceptto > Press On. selecting and 8)

MenuOption installer the entering , Offdefault to reset o T

.acceptto > Press . Offselecting and 8) (Option

type.Application

22083Model

underfloorHydronic or radiator for used be can (Battery)

applications.

select:Option installer In

.Radiator=0

8)(Fig

.underfloorHydronic =1

.Radiator=0 Default

22087Model

applications.heat electric for used be also can (Mains)

.heatelectric and Radiator =0

.underfloorHydronic =1

referand Menu Option installer the enter application change o T

9).(Option to

oomRProgrammable day 5:2 day 7 Digistat+3– Drayton

Thermostat

andweekends and weekdays for programs different Allowing

.differentlyprogrammed be can week the of day every also