Draytek Vigor2120n-plus, Vigor2120 User Manual

Vigor2120 Series User’s Guide

ii

Vigor2120 Series User’s Guide

iii

Vigor2120 Series

Broadband Firewall Router

User’s Guide

Version: 2.0

Firmware Version: V3.8.4

(For future update, please visit DrayTek web site)

Date: June 13, 2017

Vigor2120 Series User’s Guide

iv

Intellectual Property Rights (IPR) Information

Copyrights

© All rights reserved. This publication contains information that is protected by
copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval
system, or translated into any language without written permission from the copyright
holders.

Trademarks

The following trademarks are used in this document:

 Microsoft is a registered trademark of Microsoft Corp.
 Windows, Windows 95, 98, Me, NT, 2000, XP, Vista, 7 and Explorer are

trademarks of Microsoft Corp.

 Apple and Mac OS are registered trademarks of Apple Inc.
 Other products may be trademarks or registered trademarks of their respective

manufacturers.

Safety Instructions and Approval

Safety
Instructions

 Read the installation guide thoroughly before you set up the router.
 The router is a complicated electronic unit that may be repaired only be

authorized and qualified personnel. Do not try to open or repair the router
yourself.

 Do not place the router in a damp or humid place, e.g. a bathroom.
 The router should be used in a sheltered area, within a temperature range of +5 to

+40 Celsius.

 Do not expose the router to direct sunlight or other heat sources. The housing and

electronic components may be damaged by direct sunlight or heat sources.

 Do not deploy the cable for LAN connection outdoor to prevent electronic shock

hazards.

 Keep the package out of reach of children.
 When you want to dispose of the router, please follow local regulations on

conservation of the environment.

Warranty

We warrant to the original end user (purchaser) that the router will be free from any
defects in workmanship or materials for a period of two (2) years from the date of
purchase from the dealer. Please keep your purchase receipt in a safe place as it serves
as proof of date of purchase. During the warranty period, and upon proof of purchase,
should the product have indications of failure due to faulty workmanship and/or
materials, we will, at our discretion, repair or replace the defective products or
components, without charge for either parts or labor, to whatever extent we deem
necessary tore-store the product to proper operating condition. Any replacement will
consist of a new or re-manufactured functionally equivalent product of equal value, and
will be offered solely at our discretion. This warranty will not apply if the product is
modified, misused, tampered with, dam aged by an act of God, or subjected to abnormal
working conditions. The warranty does not cover the bundled or licensed software of
other vendors. Defects which do not significantly affect the usability of the product will
not be covered by the warranty. We reserve the right to revi se the m anual and onli ne
documentation and to make changes from time to time in the contents hereof without
obligation to notify any person of such revision or changes.

Be a Registered
Owner

Web registration is preferred. You can register your Vigor router via
http://www.DrayTek.com.

Firmware & Tools
Updates

Due to the continuous evolution of DrayTek technology, all routers will be regularly
upgraded. Please consult the DrayTek web site for more information on newest
firmware, tools and documents.

http://www.DrayTek.com

Vigor2120 Series User’s Guide

v

Declaration of Conformity

Hereby, DrayTek Corporation declares that the radio equipment type Vigor2120 is in compliance with Directive
2014/53/EU.

The full text of the EU Declaration of Conformity is available at the following internet address:
http://www.draytek.com.tw/ftp/Vigor2120/Document/CE/
Manufacturer: DrayTek Corp.
Address: No. 26, Fu Shing Road, Hukou Township, Hsinchu Industrial Park, Hsinchu County, Taiwan 303
Product: Vigor2120 Series Router
Frequency Information for Europe area:

2.4G WLAN 2412MHz - 2472 MHz, max. TX power: 19.95dBm
5G WLAN 5180MHz - 5700 MHz, max. TX power: 25.65dBm

Requirements in AT/BE/BG/CZ/DZ/DK/EE/FR/DE/IS/IE/IT/EL/ES/
CY/LV/LI/LT/LU/HU/MT/NL/NO/PL/PT/RO/SI/SK/TR/FI/SE/CH/
UK/HR. 5150MHz~5350MHz is for indoor use only.

This product is designed for 2.4GHz /5GHz WLAN network throughout the EC region.

Regulatory Information

Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one of the following measures:

 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
 Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device may accept any interference received, including interference that may cause undesired operation.

Vigor2120 Series User’s Guide

vi

The antenna/transmitter should be kept at least 20 cm away from human body.

More update, please visit www.draytek.com.

Vigor2120 Series User’s Guide

vii

TTaabbllee ooff CCoonntteennttss

Introduction...................................................................................................1

1.1 Web Configuration Buttons Explanation................................................................................. 2

1.2 LED Indicators and Connectors.............................................................................................. 3

1.2.1 For Vigor2120................................................................................................................... 3

1.2.2 For Vigor2120n-plus......................................................................................................... 5

1.3 Hardware Installation .............................................................................................................. 7

1.4 Printer Installation ................................................................................................................... 8

1.5 Accessing Web Page............................................................................................................ 16

1.6 Changing Password.............................................................................................................. 17

1.7 Introducing Dashboard.......................................................................................................... 18

1.7.1 Virtual Panel ................................................................................................................... 19

1.7.2 Name with a Link............................................................................................................ 19

1.7.3 Quick Access for Common Used Menu.......................................................................... 20

1.7.4 GUI Map ......................................................................................................................... 21

1.7.5 Web Console.................................................................................................................. 22

1.7.6 Config Backup ................................................................................................................ 22

1.7.7 Logout............................................................................................................................. 23

1.8 Online Status......................................................................................................................... 24

1.8.1 Physical Connection for IPv4 Protocol ........................................................................... 24

1.8.2 Physical Connection for IPv6 Protocol ........................................................................... 24

1.8.3 Virtual WAN.................................................................................................................... 26

1.9 Saving Configuration............................................................................................................. 26

Quick Setup.................................................................................................27

2.1 Quick Start Wizard................................................................................................................ 27

2.1.1 For WAN1 (Ethernet)...................................................................................................... 29

2.1.2 For WAN2 (USB)............................................................................................................38

2.2 Service Activation Wizard...................................................................................................... 40

2.3 VPN Client Wizard ................................................................................................................ 43

2.4 VPN Server Wizard............................................................................................................... 49

2.5 Registering Vigor Router....................................................................................................... 54

Tutorials and Applications.........................................................................57

3.1 How to configure settings for IPv6 Service in Vigor2120...................................................... 57

3.2 How can I get the files from USB storage device connecting to Vigor router?..................... 67

Vigor2120 Series User’s Guide

viii

3.3 How to Build a LAN-to-LAN VPN Between Remote Office and Headquarter via IPsec Tunnel

(Main Mode)................................................................................................................................ 69

3.4 How to Optimize the Bandwidth through QoS Technology................................................... 74

3.5 How to Create an Account for MyVigor................................................................................. 79

3.5.1 Create an Account via Vigor Router............................................................................... 79

3.5.2 Create an Account via MyVigor Web Site ...................................................................... 83

3.6 How to Send a Notification to Specified Phone Number via SMS Service in WAN

Disconnection.............................................................................................................................. 86

3.7 How to Configure Certain Computers Accessing to Internet................................................ 90

3.8 How to Block Facebook Service Accessed by the Users via Web Content Filter / URL

Content Filter............................................................................................................................... 94

3.9 How to use SmartMonitor with Vigor2120 series................................................................ 100

Advanced Configuration..........................................................................101

4.1 WAN.................................................................................................................................... 101

4.1.1 Basics of Internet Protocol (IP) Network....................................................................... 101

4.1.2 General Setup............................................................................................................... 103

4.1.3 Internet Access............................................................................................................. 105

4.1.4 Multi-VLAN.................................................................................................................... 131

4.2 LAN ..................................................................................................................................... 135

4.2.1 Basics of LAN ............................................................................................................... 135

4.2.2 General Setup............................................................................................................... 137

4.2.3 Static Route.................................................................................................................. 147

4.2.4 VLAN............................................................................................................................. 152

4.2.5 Bind IP to MAC............................................................................................................. 155

4.2.6 LAN Port Mirror............................................................................................................. 157

4.2.7 Web Portal Setup.......................................................................................................... 158

4.3 NA T..................................................................................................................................... 161

4.3.1 Port Redirection............................................................................................................ 161

4.3.2 DMZ Host...................................................................................................................... 165

4.3.3 Open Ports.................................................................................................................... 168

4.3.4 Address Mapping.......................................................................................................... 170

4.3.5 Port Triggering.............................................................................................................. 172

4.4 Hardware Acceleration........................................................................................................ 175

4.5 Firewall................................................................................................................................ 176

4.5.1 Basics for Firewall......................................................................................................... 176

4.5.2 General Setup............................................................................................................... 178

4.5.3 Filter Setup ................................................................................................................... 183

4.5.4 DoS Defense ................................................................................................................ 194

4.6 Objects Settings.................................................................................................................. 198

4.6.1 IP Object....................................................................................................................... 198

4.6.2 IP Group ....................................................................................................................... 202

4.6.3 IPv6 Object................................................................................................................... 203

4.6.4 IPv6 Group.................................................................................................................... 205

4.6.5 Service Type Object ..................................................................................................... 206

4.6.6 Service Type Group...................................................................................................... 208

4.6.7 Keyword Object ............................................................................................................209

Vigor2120 Series User’s Guide

ix

4.6.8 Keyword Group............................................................................................................. 211

4.6.9 File Extension Object.................................................................................................... 212

4.6.10 SMS/Mail Service Object............................................................................................ 214

4.6.11 Notification Object....................................................................................................... 219

4.7 CSM .................................................................................................................................... 221

4.7.1 APP Enforcement Profile.............................................................................................. 222

4.7.2 URL Content Filter Profile............................................................................................. 224

4.7.3 Web Content Filter Profile............................................................................................. 228

4.7.4 DNS Filter Profile.......................................................................................................... 232

4.8 Bandwidth Management ..................................................................................................... 234

4.8.1 Sessions Limit............................................................................................................... 234

4.8.2 Bandwidth Limit ............................................................................................................236

4.8.3 Quality of Service.......................................................................................................... 238

4.8.4 APP QoS ...................................................................................................................... 246

4.9 Applications......................................................................................................................... 248

4.9.1 Dynamic DNS............................................................................................................... 248

4.9.2 LAN DNS...................................................................................................................... 251

4.9.3 Schedule....................................................................................................................... 254

4.9.4 RADIUS........................................................................................................................ 256

4.9.5 UPnP............................................................................................................................. 257

4.9.6 IGMP............................................................................................................................. 259

4.9.7 Wake on LAN................................................................................................................ 260

4.9.8 SMS / Mail Alert Service............................................................................................... 261

4.9.9 Bonjour.......................................................................................................................... 263

4.10 VPN and Remote Access.................................................................................................. 266

4.10.1 Remote Access Control.............................................................................................. 266

4.10.2 PPP General Setup .................................................................................................... 267

4.10.3 IPsec General Setup................................................................................................... 269

4.10.4 IPsec Peer Identity...................................................................................................... 271

4.10.5 Remote Dial-in User ................................................................................................... 273

4.10.6 LAN to LAN................................................................................................................. 276

4.10.7 Connection Management ........................................................................................... 287

4.11 Certificate Management.................................................................................................... 287

4.11.1 Local Certificate.......................................................................................................... 288

4.11.2 Trusted CA Certificate ................................................................................................ 291

4.11.3 Certificate Backup....................................................................................................... 294

4.12 Wireless LAN(2.4GHz/5GHz) ........................................................................................... 295

4.12.1 Basic Concepts........................................................................................................... 295

4.12.2 General Setup............................................................................................................. 297

4.12.3 Security....................................................................................................................... 299

4.12.4 Access Control............................................................................................................ 302

4.12.5 WPS............................................................................................................................ 303

4.12.6 WDS............................................................................................................................ 306

4.12.7 Advanced Setting........................................................................................................ 309

4.12.8 Station Control............................................................................................................ 312

4.12.9 AP Discovery.............................................................................................................. 313

4.12.10 Airtime Fairness........................................................................................................ 314

4.12.11 Band Steering........................................................................................................... 316

4.12.12 Station List................................................................................................................ 320

4.13 SSL VPN........................................................................................................................... 321

4.13.1 General Setup............................................................................................................. 321

4.13.2 SSL Application .......................................................................................................... 322

4.13.3 User Account.............................................................................................................. 324

Vigor2120 Series User’s Guide

x

4.13.4 Online User Status...................................................................................................... 328

4.14 USB Application................................................................................................................ 329

4.14.1 USB General Settings................................................................................................. 329

4.14.2 USB User Management.............................................................................................. 331

4.14.3 File Explorer................................................................................................................ 333

4.14.4 USB Device Status..................................................................................................... 333

4.14.5 Modem Support List.................................................................................................... 335

4.14.6 SMB Client Support List.............................................................................................. 336

4.15 System Maintenance......................................................................................................... 337

4.15.1 System Status............................................................................................................. 337

4.15.2 TR-069........................................................................................................................ 339

4.15.3 Administrator Password.............................................................................................. 341

4.15.4 User Password ........................................................................................................... 341

4.15.5 Login Page Greeting................................................................................................... 344

4.15.6 Configuration Backup ................................................................................................. 346

4.15.7 Syslog/Mail Alert......................................................................................................... 349

4.15.8 Time and Date............................................................................................................ 352

4.15.9 SNMP.......................................................................................................................... 354

4.15.10 Management............................................................................................................. 356

4.15.11 Self-Signed Certificate.............................................................................................. 359

4.15.12 Reboot System......................................................................................................... 360

4.15.13 Firmware Upgrade.................................................................................................... 361

4.15.14 Activation.................................................................................................................. 362

4.16 Diagnostics........................................................................................................................ 364

4.16.1 Dial-out Triggering...................................................................................................... 364

4.16.2 Routing Table ............................................................................................................. 365

4.16.3 ARP Cache Table....................................................................................................... 366

4.16.4 IPv6 Neighbour Table................................................................................................. 366

4.16.5 DHCP Table................................................................................................................ 367

4.16.6 NAT Sessions Table................................................................................................... 368

4.16.7 DNS Cache Table....................................................................................................... 369

4.16.8 Ping Diagnosis............................................................................................................ 370

4.16.9 Data Flow Monitor....................................................................................................... 371

4.16.10 Traffic Graph............................................................................................................. 373

4.16.11 Trace Route.............................................................................................................. 374

4.16.12 System Explorer ....................................................................................................... 375

4.16.13 IPv6 TSPC Status..................................................................................................... 377

4.16.14 DoS Flood Table....................................................................................................... 377

Trouble Shooting......................................................................................379

5.1 Checking If the Hardware Status Is OK or Not....................................................................379

5.2 Checking If the Network Connection Settings on Your Computer Is OK or Not ................. 380

5.3 Pinging the Router from Y our Computer............................................................................. 383

5.4 Checking If the ISP Settings are OK or Not........................................................................ 384

5.5 Problems for 3G Network Connection ................................................................................ 384

5.6 Backing to Factory Default Setting If Necessary ................................................................ 385

5.7 Contacting DrayTek............................................................................................................. 387

Telnet Command Reference..........................................................................................389

Vigor2120 Series User’s Guide

xi

Accessing Telnet of Vigor2120.................................................................................................. 389

Telnet Command: bpa........................................................................................................... 390

Telnet Command: csm appe prof.......................................................................................... 391

Telnet Command: csm appe set............................................................................................ 391

Telnet Command: csm appe show........................................................................................ 392

Telnet Command: csm appe config....................................................................................... 393

Telnet Command: csm ucf..................................................................................................... 393

Telnet Command: csm ucf obj INDEX uac............................................................................ 395

Telnet Command: csm ucf obj INDEX wf.............................................................................. 397

Telnet Command: csm wcf.................................................................................................... 398

Telnet Command: csm dnsf................................................................................................... 400

Telnet Command: ddns log.................................................................................................... 401

Telnet Command: ddns time.................................................................................................. 401

Telnet Command: dos ........................................................................................................... 402

Telnet Command: exit............................................................................................................ 403

Telnet Command: Internet..................................................................................................... 403

Telnet Command: ip pubsubnet............................................................................................. 404

Telnet Command: ip pubaddr................................................................................................ 404

Telnet Command: ip pubmask............................................................................................... 405

Telnet Command: ip aux........................................................................................................ 405

Telnet Command: ip addr...................................................................................................... 406

Telnet Command: ip nmask................................................................................................... 407

Telnet Command: ip arp........................................................................................................ 407

Telnet Command: ip dhcpc.................................................................................................... 408

Telnet Command: ip ping....................................................................................................... 409

Telnet Command: ip tracert................................................................................................... 409

Telnet Command: ip telnet..................................................................................................... 410

Telnet Command: ip rip ......................................................................................................... 410

Telnet Command: ip wanrip................................................................................................... 411

Telnet Command: ip route..................................................................................................... 412

Telnet Command: ip igmp_proxy........................................................................................... 413

Telnet Command: ip igmp_snoop.......................................................................................... 413

Telnet Command: ip wanaddr................................................................................................ 415

Telnet Command: ip wanttr.................................................................................................... 415

Telnet Command: ip dmz....................................................................................................... 415

Telnet Command: ip dmzswitch............................................................................................. 416

Telnet Command: ip session................................................................................................. 416

Telnet Command: ip bandwidth............................................................................................. 417

Telnet Command: ip bindmac................................................................................................ 418

Telnet Command: ip maxnatuser........................................................................................... 420

Telnet Command: ip lanDNSRes .......................................................................................... 420

Telnet Command: ip6 addr.................................................................................................... 421

Telnet Command: ip6 dhcp req_opt...................................................................................... 422

Telnet Command: ip6 dhcp client.......................................................................................... 423

Telnet Command: ip6 dhcp server ........................................................................................ 424

Telnet Command: ip6 internet ............................................................................................... 425

Telnet Command: ip6 neigh................................................................................................... 426

Telnet Command: ip6 pneigh................................................................................................. 427

Telnet Command: ip6 route................................................................................................... 427

Telnet Command: ip6 ping..................................................................................................... 428

Telnet Command: ip6 tspc..................................................................................................... 429

Telnet Command: ip6 radvd .................................................................................................. 429

Telnet Command: ip6 mngt ................................................................................................... 430

Telnet Command: ip6 online.................................................................................................. 431

Telnet Command: ip6 aiccu................................................................................................... 431

Telnet Command: ip6 ntp ...................................................................................................... 432

Telnet Command: ipf view..................................................................................................... 432

Telnet Command: ipf set........................................................................................................ 433

Telnet Command: ipf rule ...................................................................................................... 435

Telnet Command: ipf flowtrack.............................................................................................. 438

Vigor2120 Series User’s Guide

xii

Telnet Command: Log........................................................................................................... 439

Telnet Command: mngt ftpport.............................................................................................. 441

Telnet Command: mngt httpport............................................................................................ 441

Telnet Command: mngt httpsport.......................................................................................... 441

Telnet Command: mngt telnetport......................................................................................... 442

Telnet Command: mngt sshport ............................................................................................ 442

Telnet Command: mngt ftpserver.......................................................................................... 442

Telnet Command: mngt noping ............................................................................................. 443

Telnet Command: mngt defenseworm .................................................................................. 444

Telnet Command: mngt rmtcfg.............................................................................................. 444

Telnet Command: mngt echoicmp......................................................................................... 445

Telnet Command: mngt accesslist ........................................................................................ 445

Telnet Command: mngt snmp ............................................................................................... 446

Telnet Command: msubnet switch........................................................................................ 447

Telnet Command: msubnet addr........................................................................................... 447

Telnet Command: msubnet nmask........................................................................................ 448

Telnet Command: msubnet status......................................................................................... 448

Telnet Command: msubnet dhcps......................................................................................... 448

Telnet Command: msubnet nat ............................................................................................. 449

Telnet Command: msubnet gateway..................................................................................... 449

Telnet Command: msubnet ipcnt........................................................................................... 450

Telnet Command: msubnet talk............................................................................................. 450

Telnet Command: msubnet startip ........................................................................................ 451

Telnet Command: msubnet pppip ......................................................................................... 451

Telnet Command: msubnet nodetype ................................................................................... 452

Telnet Command: msubnet primWINS .................................................................................. 452

Telnet Command: msubnet secWINS................................................................................... 453

Telnet Command: msubnet tftp ............................................................................................. 454

Telnet Command: msubnet mtu ............................................................................................ 454

Telnet Command: object ip obj.............................................................................................. 455

Telnet Command: object ip grp.............................................................................................. 456

Telnet Command: object ipv6 obj.......................................................................................... 458

Telnet Command: object ipv6 grp.......................................................................................... 459

Telnet Command: object service obj ..................................................................................... 460

Telnet Command: object service grp..................................................................................... 462

Telnet Command: object kw.................................................................................................. 463

Telnet Command: object fe.................................................................................................... 464

Telnet Command: port........................................................................................................... 466

Telnet Command: portmaptime............................................................................................. 466

Telnet Command: prn............................................................................................................ 467

Telnet Command: qos setup.................................................................................................. 467

Telnet Command: qos class.................................................................................................. 469

Telnet Command: qos type.................................................................................................... 470

Telnet Command: quit ........................................................................................................... 471

Telnet Command: show lan................................................................................................... 471

Telnet Command: show dmz................................................................................................. 472

Telnet Command: show dns.................................................................................................. 472

Telnet Command: show openport ......................................................................................... 472

Telnet Command: show nat................................................................................................... 472

Telnet Command: show portmap........................................................................................... 473

Telnet Command: show pmtime............................................................................................ 473

Telnet Command: show session............................................................................................ 473

Telnet Command: show status.............................................................................................. 473

Telnet Command: show traffic............................................................................................... 474

Telnet Command: show statistic............................................................................................ 474

Telnet Command: srv dhcp dhcp2......................................................................................... 475

Telnet Command: srv dhcp public......................................................................................... 475

Telnet Command: srv dhcp dns1........................................................................................... 476

Telnet Command: srv dhcp dns2........................................................................................... 477

Telnet Command: srv dhcp frcdnsmanl................................................................................. 477

Vigor2120 Series User’s Guide

xiii

Telnet Command: srv dhcp gateway..................................................................................... 477

Telnet Command: srv dhcp ipcnt........................................................................................... 478

Telnet Command: srv dhcp off............................................................................................... 478

Telnet Command: srv dhcp on............................................................................................... 478

Telnet Command: srv dhcp relay........................................................................................... 478

Telnet Command: srv dhcp startip......................................................................................... 479

Telnet Command: srv dhcp status......................................................................................... 479

Telnet Command: srv dhcp leasetime................................................................................... 480

Telnet Command: srv dhcp nodetype.................................................................................... 480

Telnet Command: srv dhcp primWINS.................................................................................. 481

Telnet Command: srv dhcp secWINS ................................................................................... 481

Telnet Command: srv dhcp expRecycleIP ............................................................................ 482

Telnet Command: srv dhcp tftp.............................................................................................. 482

Telnet Command: srv dhcp tftpdel......................................................................................... 482

Telnet Command: srv dhcp option......................................................................................... 483

Telnet Command: srv nat addrmapping................................................................................ 484

Telnet Command: srv nat dmz............................................................................................... 485

Telnet Command: srv nat ipsecpass..................................................................................... 485

Telnet Command: srv nat openport....................................................................................... 486

Telnet Command: srv nat portmap........................................................................................ 487

Telnet Command: srv nat showall......................................................................................... 490

Telnet Command: switch -i.................................................................................................... 490

Telnet Command: switch status............................................................................................. 491

Telnet Command: sys admin................................................................................................. 491

Telnet Command: sys bonjour............................................................................................... 491

Telnet Command: sys cfg...................................................................................................... 492

Telnet Command: sys cmdlog............................................................................................... 492

Telnet Command: sys ftpd..................................................................................................... 493

Telnet Command: sys domainname...................................................................................... 493

Telnet Command: sys iface................................................................................................... 494

Telnet Command: sys name.................................................................................................. 495

Telnet Command: sys passwd............................................................................................... 495

Telnet Command: sys reboot................................................................................................. 495

Telnet Command: sys autoreboot ......................................................................................... 496

Telnet Command: sys commit............................................................................................... 496

Telnet Command: sys tftpd.................................................................................................... 496

Telnet Command: sys cc....................................................................................................... 496

Telnet Command: sys version............................................................................................... 497

Telnet Command: sys qrybuf................................................................................................. 497

Telnet Command: sys pollbuf................................................................................................ 497

Telnet Command: sys tr069................................................................................................... 498

Telnet Command: sys sip_alg ............................................................................................... 500

Telnet Command: sys license................................................................................................ 500

Telnet Command: sys fr_log.................................................................................................. 501

Telnet Command: testmail..................................................................................................... 502

Telnet Command: upnp off.................................................................................................... 502

Telnet Command: upnp on.................................................................................................... 502

Telnet Command: upnp nat................................................................................................... 502

Telnet Command: upnp service............................................................................................. 503

Telnet Command: upnp subscribe......................................................................................... 504

Telnet Command: upnp tmpvs............................................................................................... 505

Telnet Command: upnp wan.................................................................................................. 505

Telnet Command: usb list...................................................................................................... 506

Telnet Command: vigbrg on .................................................................................................. 506

Telnet Command: vigbrg off .................................................................................................. 506

Telnet Command: vigbrg status............................................................................................. 507

Telnet Command: vigbrg cfgip............................................................................................... 507

Telnet Command: vigbrg wanstatus...................................................................................... 507

Telnet Command: vigbrg wlanstatus ..................................................................................... 507

Telnet Command: vpn group................................................................................................. 508

Vigor2120 Series User’s Guide

xiv

Telnet Command: vlan off...................................................................................................... 508

Telnet Command: vlan on...................................................................................................... 508

Telnet Command: vlan pri...................................................................................................... 508

Telnet Command: vlan restart ............................................................................................... 509

Telnet Command: vlan status................................................................................................ 509

Telnet Command: vlan subnet............................................................................................... 510

Telnet Command: vlan submode........................................................................................... 510

Telnet Command: vlan tagged............................................................................................... 511

Telnet Command: vlan vid..................................................................................................... 511

Telnet Command: vlan sysvid................................................................................................ 512

Telnet Command: vpn l2lset.................................................................................................. 512

Telnet Command: vpn l2lDrop............................................................................................... 513

Telnet Command: vpn dinset................................................................................................. 513

Telnet Command: vpn subnet................................................................................................ 515

Telnet Command: vpn setup.................................................................................................. 516

Telnet Command: vpn option................................................................................................. 518

Telnet Command: vpn mroute............................................................................................... 521

Telnet Command: vpn list...................................................................................................... 521

Telnet Command: vpn remote............................................................................................... 523

Telnet Command: vpn 2ndsubnet ......................................................................................... 523

Telnet Command: vpn NetBios.............................................................................................. 523

Telnet Command: vpn mss.................................................................................................... 524

Telnet Command: vpn ike...................................................................................................... 525

Telnet Command: vpn Multicast............................................................................................ 525

Telnet Command: vpn pass2nd............................................................................................. 526

Telnet Command: vpn pass2nat............................................................................................ 526

Telnet Command: wan ppp_mru........................................................................................... 527

Telnet Command: wan mtu.................................................................................................... 527

Telnet Command: wan DF_check......................................................................................... 528

Telnet Command: wan disable.............................................................................................. 528

Telnet Command: wan enable............................................................................................... 528

Telnet Command: wan forward.............................................................................................. 528

Telnet Command: wan status................................................................................................ 529

Telnet Command: wan modem.............................................................................................. 529

Telnet Command: wan wimax ............................................................................................... 530

Telnet Command: wan detect................................................................................................ 531

Telnet Command: wan lb....................................................................................................... 532

Telnet Command: wan mvlan................................................................................................ 532

Telnet Command: wan multifno............................................................................................. 533

Telnet Command: wan vlan................................................................................................... 534

Telnet Command: wan fiber................................................................................................... 535

Telnet Command: wptl........................................................................................................... 535

Telnet Command: wl acl........................................................................................................ 537

Telnet Command: wl config................................................................................................... 538

Telnet Command: wl set........................................................................................................ 541

Telnet Command: wl act........................................................................................................ 541

Telnet Command: wl stamgt.................................................................................................. 542

Telnet Command: wl iso_vpn ................................................................................................ 543

Telnet Command: wl wmm.................................................................................................... 543

Telnet Command: wl ht.......................................................................................................... 544

Telnet Command: wl restart................................................................................................... 545

Telnet Command: wl btnctl.................................................................................................... 545

Telnet Command: wl iwpriv.................................................................................................... 546

Telnet Command: wl efuse.................................................................................................... 546

Telnet Command: wl ce_cert................................................................................................. 546

Telnet Command: wl dual acl ................................................................................................ 546

Telnet Command: wl dual apscan......................................................................................... 547

Telnet Command: wl dual config ........................................................................................... 548

Telnet Command: wl dual cmd.............................................................................................. 550

Telnet Command: wl dual ce_cert......................................................................................... 550

Vigor2120 Series User’s Guide

xv

Telnet Command: wl dual restart........................................................................................... 550

Telnet Command: wl dual security ........................................................................................ 551

Telnet Command: wl dual stalist............................................................................................ 552

Telnet Command: wl dual wds............................................................................................... 552

Telnet Command: wl dual wps............................................................................................... 554

Telnet Command: wol............................................................................................................ 555

Telnet Command: appqos ..................................................................................................... 555

Vigor2120 Series User’s Guide

1

IInnttrroodduuccttiioonn

NNoottee:: TThhiiss iiss aa ggeenneerriicc IInntteerrnnaattiioonnaall vveerrssiioonn ooff tthhee
uusseerr gguuiiddee.. SSppeecciiffiiccaattiioonn,, ccoommppaattiibbiilliittyy aanndd ffeeaattuurreess
vvaarryy bbyy rreeggiioonn.. FFoorr ssppeecciiffiicc uusseerr gguuiiddeess ssuuiittaabbllee ffoorr
yyoouurr rreeggiioonn oorr pprroodduucctt,, pplleeaassee ccoonnttaacctt llooccaall
ddiissttrriibbuuttoorr..

Vigor2120 Series is a broadband router which integrates IP layer QoS, NAT
session/bandwidth management to help users control works well with large bandwidth.

By adopting hardware-based VPN platform and hardware encryption of AES/DES/3DES, the
router increases the performance of VPN greatly, and offers several protocols (such as
IPsec/PPTP/L2TP) with up to 2 VPN tunnels.

The object-based design used in SPI (Stateful Packet Inspection) firewall allows users to set
firewall policy with ease. CSM (Content Security Management) provides users control and
management in IM (Instant Messenger) and P2P (Peer to Peer) more efficiency than before.
By the way, DoS/DDoS prevention and URL/Web content filter strengthen the security
outside and control inside. Object-based firewall is flexible and allows your network be safe.

In addition, Vigor2120 Series supports USB interface for connecting USB printer to share
printing function or 3G/4G USB modem for network connection.

Vigor2120 Series provides two-level management to simplify the configuration of network
connection. The user mode allows user accessing into WEB interface via simple configuration.
However, if users want to have advanced configurations, they can access into WEB interface
through admin mode.

Vigor2120 Series User’s Guide

2

11..11 WWeebb CCoonnffiigguurraattiioonn BBuuttttoonnss EExxppllaannaattiioonn

Several main buttons appeared on the web pages are defined as the following:

Save and apply current settings.

Cancel current settings and recover to the previous saved settings.

Clear all the selections and parameters settings, including selection from

drop-down list. All the values must be reset with factory default settings.

Add new settings for specified item.

Edit the settings for the selected item.

Delete the selected item with the corresponding settings.

Note: For the other buttons shown on the web pages, please refer to Chapter 3, 4 for detailed
explanation.

Vigor2120 Series User’s Guide

3

11..22 LLEEDD IInnddiiccaattoorrss aanndd CCoonnnneeccttoorrss

Before you use the Vigor router, please get acquainted with the LED indicators and connectors
first.

11..22..11 FFoorr VViiggoorr22112200

LED

Status Explanation

Off The system is not ready or is failed. ACT
Blinking The system is ready and can work normally.

On A USB device is connected and active. USB

Blinking The data is transmitting.
VPN On The VPN tunnel is active.
WCF On The profile(s) of CSM (Content Security Management) for

Web Content Filter application can be enabled from
Firewall >>General Setup. (Such profile must be
established under CSM menu)

On A normal connection is through its corresponding port. LAN 1 - 4

Off LAN is disconnected.

On The WAN port is connected. WAN

Blinking It will blink while transmitting data.

Vigor2120 Series User’s Guide

4

Interface Description

Restore the default settings. Usage: Turn on the
router. Press the button and keep for more than 6
seconds. Then the router will restart with the
factory default configuration.

WAN Connector for accessing the Internet.

LAN 1- 4 Connecters for local network devices (LAN).

PWR: Connecter for a power adapter.

Connecter for a USB device (for 3G USB Modem
or printer or storage disk).

ON/OFF: Power switch.

Vigor2120 Series User’s Guide

5

11..22..22 FFoorr VViiggoorr22112200nn--pplluuss

LED

Status Explanation

Off The system is not ready or is failed. ACT

Blinking The system is ready and can work normally.

On A USB device is connected and active. USB

Blinking The data is transmitting.

On Wireless function is ready.

Off Wireless function is not ready.

2.4G

Blinking Data is transmitting (sending/receiving).

On Wireless function is ready.

Off Wireless function is not ready.

5G

Blinking Data is transmitting (sending/receiving).

On A normal connection is through its corresponding port. LAN 1 - 4

Off LAN is disconnected.

On The WAN port is connected. WAN

Blinking It will blink while transmitting data.

Vigor2120 Series User’s Guide

6

Interface Description

WLAN

ON/OFF

WPS

WLAN On - Press the button and release it within 2
seconds.

When the wireless function is ready, the 2.4G/5G blue
LED on front panel will be on.

WLAN Off - Press the button and release it within 2
seconds to turn off the WLAN function.

When the wireless function is not ready, 2.4G/5G blue
LED on front panel will be off.

WPS - When WPS function is enabled by web user
interface, press this button for more t h a n 2 seconds.

The router will wait for any wireless client connecting to
it through WPS.

Restore the default settings. Usage: Turn on the router.
Press the button and keep for more than 6 seconds. Then
the router will restart with the factory default
configuration.

WAN Connector for accessing the Internet.

LAN 1- 4 Connecters for local network devices (LAN).

PWR: Connecter for a power adapter.

Connecter for a USB device (for 3G USB Modem or
printer or storage disk).

ON/OFF: Power switch.

Vigor2120 Series User’s Guide

7

11..33 HHaarrddwwaarree IInnssttaallllaattiioonn

Before starting to configure the router, you have to connect your devices correctly.

1. Connect the cable Modem/DSL Modem/Media Converter to any WAN port of router

with Ethernet cable (RJ-45).

2. Connect one end of an Ethernet cable (RJ-45) to one of the LAN ports of the router and

the other end of the cable (RJ-45) into the Ethernet port on your computer.

3. Connect one end of the power adapter to the router’s power port on the rear panel, and

the other side into a wall outlet.

4. Power on the device by pressing down the power switch on the rear panel.

5. The system starts to initiate. After completing the system test, the ACT LED will light

up and start blinking.

(For the hardware connection, we take “n” model as an example.)

Vigor2120 Series User’s Guide

8

11..44 PPrriinntteerr IInnssttaallllaattiioonn

You can install a printer onto the router for sharing printing. All the PCs connected this router
can print documents via the router. The example provided here is made based on Windows
XP/2000. For Windows 98/SE/Vista, please visit www.DrayTek.com.

Before using it, please follow the steps below to configure settings for connected computers
(or wireless clients).

1. Connect the printer with the router through USB/parallel port.

2. Open All Programs>>Getting Started>>Devices and Printers.

3. Click Add a printer.

4. A dialog will appear. Click Add a local printer and click Next.

Vigor2120 Series User’s Guide

9

5. In this dialog, choose Create a new port. In the field of Type of port, use the drop

down list to select Standard TCP/IP Port. Then, click Next.

Vigor2120 Series User’s Guide

10

6. In the following dialog, type 192.168.1.1 (router’s LAN IP) in the field of Hostname or

IP Address and type 192.168.1.1 as the Port name. Then, click Next.

7. Click Standard and choose Generic Network Card.

Vigor2120 Series User’s Guide

11

8. Now, your system will ask you to choose right name of the printer that you installed onto

the router. Such step can make correct driver loaded onto your PC. When you finish the
selection, click Next.

9. Type a name for the chosen printer. Click Next.

Vigor2120 Series User’s Guide

12

10. Choose Do not share this printer and click Next.

11. Then, in the following dialog, click Finish.

Vigor2120 Series User’s Guide

13

12. The new printer has been added and displayed under Printers and Faxes. Click the new

printer icon and click Printer server properties.

13. Edit the property of the new printer you have added by clicking Configure Port.

Vigor2120 Series User’s Guide

14

14. Select "LPR" on Protocol, type p1 (number 1) as Queue Name. Then click OK. Next

please refer to the red rectangle for choosing the correct protocol and LPR name.

The printer can be used for printing now. Most of the printers with different manufacturers are
compatible with vigor router.

Vigor2120 Series User’s Guide

15

Note 1: Some printers with the fax/scanning or other additional functions are not supported.
If you do not know whether your printer is supported or not, please visit www.draytek.com
to find out the printer list. Open Support >FAQ/Application Notes; find out the link of
USB>>Printer Server and click it.

Then, click the What types of printers are compatible with Vigor router? link.

Note 2: Vigor router supports printing request from computers via LAN ports but not WAN
port.

Vigor2120 Series User’s Guide

16

11..55 AAcccceessssiinngg WWeebb PPaaggee

1. Make sure your PC connects to the router correctly.

You may either simply set up your computer to get IP dynamically from the router or set
up the IP address of the computer to be the same subnet as the default IP address of
Vigor router 192.168.1.1. For the detailed information, please refer to the later section ­Trouble Shooting of the guide.

2. Open a web browser on your PC and type http://192.168.1.1. The following window

will be open to ask for username and password.

3. Please type “admin/admin” as the Username/Password and click Login.

Notice: If you fail to access to the web configuration, please go to “Trouble
Shooting” for detecting and solving your problem.

4. Now, the Main Screen will appear.

Vigor2120 Series User’s Guide

17

Note: The home page will be different slightly in accordance with the type of the
router you have.

5. The web page can be logged out according to the chosen condition. The default setting is

Auto Logout, which means the web configuration system will logout after 5 minutes
without any operation. Change the setting for your necessity.

11..66 CChhaannggiinngg PPaasssswwoorrdd

Please change the password for the original security of the router.

1. Open a web browser on your PC and type http://192.168.1.1. A pop-up window will

open to ask for username and password.

2. Please type “admin/admin” as Username/Password for accessing into the web user

interface with admin mode.

3. Go to System Maintenance page and choose Administrator Password/.

4. Enter the login password (the default is “admin”) on the field of Old Password. Type

New Password. Then click OK to continue.

Note: The maximum length of the password you can set is 23 characters.

5. Now, the password has been changed. Next time, use the new password to access the

Web user interface for this router.

Vigor2120 Series User’s Guide

18

Note: Even the password has been changed, the Username for logging to the web
user interface is still “admin”.

11..77 IInnttrroodduucciinngg DDaasshhbbooaarrdd

Dashboard shows the connection status including System Information, IPv4 Internet Access,
IPv6 Internet Access, Interface (physical connection), Security and Quick Access.

Click Dashboard from the main menu on the left side of the main page.

A web page with default selections will be displayed on the screen. Refer to the following
figure:

Vigor2120 Series User’s Guide

19

11..77..11 VViirrttuuaall PPaanneell

On the top of the Dashboard, a virtual panel (simulating the physical panel of the router)
displays the physical interface connection. It will be refreshed every five seconds.

For detailed information about the LED display, refer to 1.2 LED Indicators and
Connectors.

11..77..22 NNaammee wwiitthh aa LLiinnkk

A name with a link (e.g., Router Name, Current Time, WAN1 and etc.) below means you can
click it to open the configuration page for modification.

Vigor2120 Series User’s Guide

20

11..77..33 QQuuiicckk AAcccceessss ffoorr CCoommmmoonn UUsseedd MMeennuu

All the menu items can be accessed and arranged orderly on the left side of the main page for
your request. However, some important and common used menu items which can be
accessed in a quick way just for convenience.

Look at the right side of the Dashboard. You will find a group of common used functions
grouped under Quick Access.

The function links of System Status, Dynamic DDNS, TR-069, IM/P2P Block, Schedule,
Syslog/Mail Alert, RADIUS, Firewall Object Setting and Data Flow Monitor are displayed
here. Move your mouse cursor on any one of the links and click on it. The corresponding
setting page will be open immediately.

In addition, quick access for VPN security settings such as Remote Dial-in User and LAN to
LAN are located on the bottom of this page. Scroll down the page to find them and use them if
required.

Note that there is a plus (

) icon located on the left side of VPN/LAN. Click it to review the

VPN connection(s) used presently.

Vigor2120 Series User’s Guide

21

Host connected physically to the router via LAN port(s) will be displayed with green circles in
the field of Connected.

All of the hosts (including wireless clients) displayed with Host ID, IP Address and MAC
address indicates that the traffic would be transmitted through LAN port(s) and then the WAN
port. The purpose is to perform the traffic monitor of the host(s).

11..77..44 GGUUII MMaapp

All the functions the router supports are listed with table clearly in this page. Users can click
the function link to access into the setting page of the function for detailed configuration.
Click the icon on the top of the main screen to display all the functions.

Vigor2120 Series User’s Guide

22

11..77..55 WWeebb CCoonnssoollee

It is not necessary to use the telnet command via DOS prompt. The changes made by using
web console have the same effects as modified through web user interface. The
functions/settings modified under Web Console also can be reviewed on the web user
interface.

Click the Web Console icon on the top of the main screen to open the following screen.

11..77..66 CCoonnffiigg BBaacckkuupp

There is one way to store current used settings quickly by clicking the Config Backup icon. It
allows you to backup current settings as a file. Such configuration file can be restored by using
System Maintenance>>Configuration Backup.

Simply click the icon on the top of the main screen and a pop up dialog will appear.

Vigor2120 Series User’s Guide

23

Click Save to store the setting.

11..77..77 LLooggoouutt

Click this icon to exit the web user interface.

Vigor2120 Series User’s Guide

24

11..88 OOnnlliinnee SSttaattuuss

Such page displays the physical connection status such as LAN connection status, WAN
connection status, ADSL information, and so on.

11..88..11 PPhhyyssiiccaall CCoonnnneeccttiioonn ffoorr IIPPvv44 PPrroottooccooll

11..88..22 PPhhyyssiiccaall CCoonnnneeccttiioonn ffoorr IIPPvv66 PPrroottooccooll

Detailed explanation (for IPv4) is shown below:

Item Description
LAN Status

Primary DNS-Displays the primary DNS server address for

WAN interface.
Secondary DNS -Displays the secondary DNS server

address for WAN interface.

IP Address-Displays the IP address of the LAN interface.
TX Packets-Displays the total transmitted packets at the

Vigor2120 Series User’s Guide

25

Item Description

LAN interface.
RX Packets-Displays the total received packets at the LAN

interface.

WAN1/WAN2

Enable – Yes in red means such interface is available but not
enabled. Yes in green means such interface is enabled.

Line – Displays the physical connection (Ethernet, or USB)

of this interface.

Name – Display the name of the router.
Mode - Displays the type of WAN connection (e.g., PPPoE).
Up Time - Displays the total uptime of the interface.
IP - Displays the IP address of the WAN interface.
GW IP - Displays the IP address of the default gateway.
TX Packets - Displays the total transmitted packets at the

WAN interface.
TX Rate - Displays the speed of transmitted octets at the

WAN interface.
RX Packets - Displays the total number of received packets

at the WAN interface.
RX Rate - Displays the speed of received octets at the WAN

interface.

Detailed explanation (for IPv6) is shown below:

Item Description
LAN Status

IP Address- Displays the IPv6 address of the LAN

interface..
TX Packets-Displays the total transmitted packets at the

LAN interface.
RX Packets-Displays the total received packets at the LAN

interface.
TX Bytes - Displays the speed of transmitted octets at the

LAN interface.
RX Bytes - Displays the speed of received octets at the

LAN interface.

WAN IPv6 Status

Enable – No in red means such interface is available but

not enabled. Yes in green means such interface is enabled.
No in red means such interface is not available.

Mode - Displays the type of WAN connection (e.g., TSPC).
Up Time - Displays the total uptime of the interface.
IP - Displays the IP address of the WAN interface.
Gateway IP - Displays the IP address of the default

gateway.

Note: The words in green mean that the WAN connection of that interface is ready for

accessing Internet; the words in red mean that the WAN connection of that interface is not
ready for accessing Internet.

Vigor2120 Series User’s Guide

26

11..88..33 VViirrttuuaall WWAANN

Such page displays the virtual WAN connection information.
Virtual WAN are used by TR-069 management, VoIP service and so on.
The field of Application will list the purpose of such WAN connection.

11..99 SSaavviinngg CCoonnffiigguurraattiioonn

Each time you click OK on the web page for saving the configuration, you can find messages
showing the system interaction with you.

Ready indicates the system is ready for you to input settings.
Settings Saved means your settings are saved once you click Finish or OK button.

Vigor2120 Series User’s Guide

27

Q

Quuiicckk SSeettuupp

There are several setup wizards offered for you to configure the router simply and quickly.

 Quick Start Wizard – used for building network connection, Internet access.
 Service Activation Wizard – used for activating the web content filter service.
 VPN Client Wizard – used for establishing VPN tunnel; the router is treated as a VPN

client.

 VPN Server Wizard – used for establishing VPN tunnel; the router is treated as a VPN

server.

22..11 QQuuiicckk SSttaarrtt WWiizzaarrdd

The Quick Start Wizard is designed for you to easily set up your router for Internet access.
Open Wizards>>Quick Start Wizard.

It can help you to deploy and use the router easily and quickly. The first screen of Quick Start
Wizard is entering login password. After typing the password, please click Next.

On the next page as shown below, please select the WAN interface that you use. If Ethernet
interface is used, please choose WAN1; if 3G USB modem is used, please choose WAN2.
Then click Next for next step.

Vigor2120 Series User’s Guide

28

WAN1 and WAN2 will bring up different configuration page. Refer to the following for
detailed information.

Vigor2120 Series User’s Guide

29

22..11..11 FFoorr WWAANN11 ((EEtthheerrnneett))

WAN1 is dedicated to physical mode in Ethernet. If you choose WAN1, please specify
physical type. Then, click Next.

22..11..11..11 PPPPPPooEE

1. Open Wizards>>Quick Start Wizard. Finish the password settings and click Next.

2. Choose WAN1 as the WAN Interface and click the Next button.

3. The following page will be open for you to specify Internet Access Type. Click PPPoE

as the Internet Access Type. Then click Next to continue.

Vigor2120 Series User’s Guide

30

4. Please manually enter the Username/Password provided by your ISP. Click Next for

viewing summary of such connection.

Available settings are explained as follows:

Item Description
Service Name

Type the service information for identifying ISP.

Username

Assign a specific valid user name provided by the ISP.

Password

Assign a valid password provided by the ISP.

Confirm Password

Retype the password.

Back

Click it to return to previous setting page.

Next

Click it to get into the next setting page.

Cancel

Click it to give up the quick start wizard.

5. A summary page will be displayed as follows.

Vigor2120 Series User’s Guide

31

6. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear.

7. Now, you can enjoy surfing on the Internet.

Vigor2120 Series User’s Guide

32

22..11..11..22 PPPPTTPP//LL22TTPP

1. Open Wizards>>Quick Start Wizard. Finish the password settings and click Next.

2. Choose WAN1 as the WAN Interface and click the Next button.

3. The following page will be open for you to specify Internet Access Type. Click

PPTP/L2TP as the Internet Access Type. Then click Next to continue.

4. Please type in the IP address/mask/gateway information originally provided by your ISP.

Then click Next for viewing summary of such connection.

Available settings are explained as follows:

Item Description
User Name

Assign a specific valid user name provided by the ISP.

Password

Assign a valid password provided by the ISP.

Confirm Password

Retype the password.

Vigor2120 Series User’s Guide

33

WAN IP
Configuration

Obtain an IP address automatically – the router will get

an IP address automatically from DHCP server.
Specify an IP address – you have to type relational

settings manually.

IP Address - Type the IP address.
Subnet Mask –Type the subnet mask.
Gateway – Type the IP address of the gateway.
Primary DNS –Type in the primary IP address for the

router.
Second DNS –Type in secondary IP address for necessity

in the future.

PPTP Server / L2TP
Server

Type the IP address of the server.

Back

Click it to return to previous setting page.

Next

Click it to get into the next setting page.

Cancel

Click it to give up the quick start wizard.

5. A summary page will be displayed as follows.

6. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear.

7. Now, you can enjoy surfing on the Internet.

Vigor2120 Series User’s Guide

34

22..11..11..33 SSttaattiicc IIPP

1. Open Wizards>>Quick Start Wizard. Finish the password settings and click Next.

2. Choose WAN1 as the WAN Interface and click the Next button.

3. The following page will be open for you to specify Internet Access Type. Click Static IP

as the Internet Access Type. Then click Next to continue.

4. Please type in the IP address information originally provided by your ISP. Then click

Next for viewing summary of such connection..

Available settings are explained as follows:

Item Description
WAN IP

Type the IP address.

Subnet Mask

Type the subnet mask.

Gateway

Type the IP address of gateway.

Primary DNS

Type in the primary IP address for the router.

Vigor2120 Series User’s Guide

35

Secondary DNS

Type in secondary IP address for necessity in the future.

Back

Click it to return to previous setting page.

Next

Click it to get into the next setting page.

Cancel

Click it to give up the quick start wizard.

5. A summary page will be displayed as follows.

6. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear.

7. Now, you can enjoy surfing on the Internet.

Vigor2120 Series User’s Guide

36

22..11..11..44 DDHHCCPP

1. Open Wizards>>Quick Start Wizard. Finish the password settings and click Next.

2. Choose WAN1 as the WAN Interface and click the Next button.

3. The following page will be open for you to specify Internet Access Type. Click DHCP

as the Internet Access Type. Then click Next to continue.

4. Click DHCP as the Internet Access type. Simply click Next to continue. Then click Next

for viewing summary of such connection.

Available settings are explained as follows:

Item Description
Host Name

Type the name of the host.
Note: The maximum length of the host name you can set is

39 characters.

MAC

Some Cable service providers specify a specific MAC
address for access authentication. In such cases you need to

Vigor2120 Series User’s Guide

37

enter the MAC address.

Back

Click it to return to previous setting page.

Next

Click it to get into the next setting page.

Cancel

Click it to give up the quick start wizard.

5. A summary page will be displayed as follows.

6. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear.

7. Now, you can enjoy surfing on the Internet.

Vigor2120 Series User’s Guide

38

22..11..22 FFoorr WWAANN22 ((UUSSBB))

WAN2 is dedicated to physical mode in USB.

1. Open Wizards>>Quick Start Wizard. Finish the password settings and click Next

2. Choose WAN2 as the WAN Interface and click the Next button.

3. In the following page, fill in the information for 3G/4G USB Modem.

Available settings are explained as follows:

Item Description
Internet Access

Choose a protocol for accessing the Internet.

3G/4G USB Modem
(PPP mode)

SIM Pin code –Type PIN code of the SIM card that will be

used to access Internet. The maximum length of the pin
code you can set is 15 characters.

Modem Initial String – Such value is used to initialize
USB modem. Please use the default value. If you have any
question, please contact to your ISP. The maximum length

Vigor2120 Series User’s Guide

39

of the string you can set is 47 characters.
APN Name – APN means Access Point Name which is

provided and required by some ISPs. Type the name and
click Apply.

3G/4G USB Modem
(DHCP mode)

SIM Pin code –Type PIN code of the SIM card that will be

used to access Internet.
Network Mode – Force Vigor router to connect Internet

with the mode specified here. If you choose 4G/3G/2G as
network mode, the router will choose a suitable one
according to the actual wireless signal automatically.

APN Name – APN means Access Point Name which is
provided and required by some ISPs.

4. Then, click Next for viewing summary of such connection.

5. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear.

6. Now, you can enjoy surfing on the Internet.

Vigor2120 Series User’s Guide

40

22..22 SSeerrvviiccee AAccttiivvaattiioonn WWiizzaarrdd

Service Activation Wizard can guide you to activate WCF service (Web Content Filter) with a
quick and easy way. For the Service Activation Wizard is only available for admin

operation, therefore, please type “admin/admin” on Username/Password while Logging
into the web user interface.

Service Activation Wizard is a tool which allows you to use trial version of WCF directly
without accessing into the server (MyVigor) located on http://myvigor.draytek.com

. For using

Web Content Filter Profile, please refer to later section Web Content Filter Profile for
detailed information.

Now, follow the steps listed below to activate WCF feature for your router.

Note: Such function is available only for Admin Mode.

1. Open Wizards>>Service Activation Wizard.

2. The screen of Service Activation Wizard will be shown as follows. Choose the one you

need and click Next. In this case, we choose to activate free trail edition.

Free trial edition: it offers a period of trial for you to get acquainted with WCF function.

Vigor2120 Series User’s Guide

41

3. In the following page, you can activate the Web content filter services at the same time

or individually. When you finish the selection, please click Next.

Commtouch is the web content filter based on Commtouch operated in the
worldwide. There is a 30-day trial period. After trial, you can purchase DrayTek's
prepared Commtouch GlobalView WCF package from retailing outlets.

BPjM is WCF for German Speaking users. The fragfINN is whitelist for German
Speaking users. The BPjM is ideal for your family to provide more Internet security
for youngsters.

Ｗeb Content Filter (fragFINN) service had not been supported since January 1,

2015.

4. Setting confirmation page will be displayed as follows, please click Next.

Vigor2120 Series User’s Guide

42

5. Wait for a moment till the following page appears.

When such page appears, you can enable or disable these services for your necessity.
Then, click Finish.

Note: The service will be activated and applied as the default rule configured in
Firewall>>General Setup.

6. Now, the web page will display the service that you have activated according to your

selection(s). The valid time for the free trial of these services is one month.

When all the trial editions for various web content filters had been enabled, the
configuration page of Service Activation Wizard will be invalid as shown below.

Vigor2120 Series User’s Guide

43

22..33 VVPPNN CClliieenntt WWiizzaarrdd

Such wizard is used to configure VPN settings for VPN client. Such wizard will guide to set
the LAN-to-LAN profile for VPN dial out connection (from server to client) step by step.

1. Open VPN and Remote Access>>VPN Client Wizard. The following page will appear.

Available settings are explained as follows:

Item Description
LAN-to-LAN Client

Mode Selection

Choose the client mode.
Route Mode/NAT Mode – If the remote network only

allows you to dial in with single IP, please choose this
mode, otherwise please choose Route Mode.

Please choose a
LAN-to-LAN Profile

There are 32 VPN profiles for users to set.

Vigor2120 Series User’s Guide

44

2. When you finish the mode and profile selection, please click Next to open the following

page.

In this page, you have to select suitable VPN type for the VPN client profile. There are six
types provided here. Different type will lead to different configuration page. After making
the choices for the client profile, please click Next. You will see different configurations
based on the selection(s) you made.

Vigor2120 Series User’s Guide

45

Note: The following descriptions for VPN Type are based on the Route Mode
specified in LAN-to-LAN Client Mode Selection.

 When you choose PPTP (None Encryption) or PPTP (Encryption), you will see the

following graphic:

 When you choose IPsec, you will see the following graphic:

Vigor2120 Series User’s Guide

46

 When you choose L2TP, you will see the following graphic:

 When you choose L2TP over IPsec (Nice to Have) or L2TP over IPsec (Must), you

will see the following graphic:

Vigor2120 Series User’s Guide

47

 When you choose SSL, you will see the following graphic:

Available settings are explained as follows:

Item Description
Profile Name

Type a name for such profile. The length of the file is
limited to 10 characters.

Always On

Check to enable router always keep VPN connection.

Server IP/Host Name
for VPN

Type the IP address of the server or type the host name for
such VPN profile.

IKE Authentication
Method

IKE Authentication Method usually applies to those are
remote dial-in user or node (LAN to LAN) which uses
dynamic IP address and IPsec-related VPN connections
such as L2TP over IPsec and IPsec tunnel.

Pre-Shared Key- Specify a key for IKE authentication.
Confirm Pre-Shared Key-Confirm the pre-shared key.
Digital Signature (X.509) - Click Digital Signature to

invoke this function.

 Peer ID – Choose the peer ID selection from the drop

down list.

 Local ID – Choose Alternative Subject Name First or

Subject Name First.

 Local Certificate – Use the drop down list to choose

one of the certificates for using. You have to configure
one certificate at least previously in Certificate
Management >> Local Certificate. Otherwise, the
setting you choose here will not be effective.

IPsec Security
Method

Medium - Authentication Header (AH) means data will be

authenticated, but not be encrypted. By default, this option
is active.

High - Encapsulating Security Payload (ESP) means

Vigor2120 Series User’s Guide

48

payload (data) will be encrypted and authenticated. You
may select encryption algorithm from Data Encryption
Standard (DES), Triple DES (3DES), and AES.

User Name

This field is used to authenticate for connection when you
select PPTP or L2TP with or without IPsec policy above.

The length of the user name is limited to 11 characters.

Password

This field is used to authenticate for connection when you
select PPTP or L2TP with or without IPsec policy above.

The length of the password is limited to 11 characters.

Remote Network IP

Please type one LAN IP address (according to the real
location of the remote host) for building VPN connection.

Remote Network
Mask

Please type the network mask (according to the real location
of the remote host) for building VPN connection.

3. After finishing the configuration, please click Next. The confirmation page will be shown

as follows. If there is no problem, you can click one of the radio buttons listed on the page
and click Finish to execute the next action.

Available settings are explained as follows:

Item Description
Go to the VPN

Connection
Management

Click this radio button to access VPN and Remote
Access>>Connection Management for viewing VPN

Connection status.

Do another VPN
Server Wizard Setup

Click this radio button to set another profile of VPN Server
through VPN Server Wizard.

View more detailed
configuration

Click this radio button to access VPN and Remote
Access>>LAN to LAN for viewing detailed configuration.

Vigor2120 Series User’s Guide

49

22..44 VVPPNN SSeerrvveerr WWiizzaarrdd

Such wizard is used to configure VPN settings for VPN server. Such wizard will guide to set
the LAN-to-LAN profile for VPN dial in connection (from client to server) step by step.

1. Open VPN and Remote Access>>VPN Server Wizard. The following page will appear.

Available settings are explained as follows:

Item Description
VPN Server Mode

Selection

Choose the direction for the VPN server.
Site to Site VPN – To set a LAN-to-LAN profile

automatically, please choose Site to Site VPN.
Remote Dial-in User –You can manage remote access by

maintaining a table of remote user profile, so that users can
be authenticated to dial-in via VPN connection.

Please choose a
LAN-to-LAN Profile

This item is available when you choose Site to Site VPN
(LAN-to-LAN) as VPN server mode. There are 32 VPN
profiles for users to set.

Vigor2120 Series User’s Guide

50

Please choose a
Dial-in User
Accounts

This item is available when you choose Remote Dial-in
User (Teleworker) as VPN server mode. There are 32 VPN
tunnels for users to set.

Allowed Dial-in Type

This item is available after you choose any one of dial-in
user account profiles. Next, you have to select suitable
dial-in type for the VPN server profile. There are several
types provided here (similar to VPN Client Wizard).

Different Dial-in Type will lead to different configuration
page. In addition, adjustable items for each dial-in type will
be changed according to the VPN Server Mode (Site to Site
VPN and Remote Dial-in User) selected.

2. After making the choices for the server profile, please click Next. You will see different

configurations based on the selection you made.

Here we take the examples of choosing Site-to-Site VPN as the VPN Server Mode.

Vigor2120 Series User’s Guide

51

 When you check PPTP, you will see the following graphic:

 When you check PPTP & IPsec & L2TP (three types) or PPTP & IPsec (two types) or

L2TP with Policy (Nice to Have/Must), you will see the following graphic:

Vigor2120 Series User’s Guide

52

 When you check IPsec, you will see the following graphic:

Available settings are explained as follows:

Item Description
Profile Name

Type a name for such profile. The length of the file is
limited to 10 characters.

User Name

This field is used to authenticate for connection when you
select PPTP or L2TP with or without IPsec policy above.

The length of the name is limited to 11 characters.

Password

This field is used to authenticate for connection when you
select PPTP or L2TP with or without IPsec policy above.

The length of the name is limited to 11 characters.

Pre-Shared Key

For IPsec/L2TP IPsec authentication, you have to type a
pre-shared key.

The length of the name is limited to 64 characters.

Confirm Pre-Shared
Key

Type the pre-shared key again for confirmation.

Digital Signature
(X.509)

Check the box of Digital Signature to invoke this function.
Peer ID – Choose the peer ID selection from the drop down

list.

Local ID – Choose Alternative Subject Name First or
Subject Name First.

Peer IP/VPN Client
IP

Type the WAN IP address or VPN client IP address for the
remote client.

Peer ID

Type the ID name for the remote client.
The length of the name is limited to 47 characters.

Vigor2120 Series User’s Guide

53

Remote Network IP

Please type one LAN IP address (according to the real
location of the remote host) for building VPN connection.

Remote Network
Mask

Please type the network mask (according to the real location
of the remote host) for building VPN connection.

3. After finishing the configuration, please click Next. The confirmation page will be shown

as follows. If there is no problem, you can click one of the radio buttons listed on the page
and click Finish to execute the next action.

Available settings are explained as follows:

Item Description
Go to the VPN

Connection
Management

Click this radio button to access VPN and Remote
Access>>Connection Management for viewing VPN

Connection status.

Do another VPN
Server Wizard Setup

Click this radio button to set another profile of VPN Server
through VPN Server Wizard.

View more detailed
configuration

Click this radio button to access VPN and Remote
Access>>LAN to LAN for viewing detailed configuration.

Vigor2120 Series User’s Guide

54

22..55 RReeggiisstteerriinngg VViiggoorr RRoouutteerr

You have finished the configuration of Quick Start Wizard and you can surf the Internet at any
time. Now it is the time to register your Vigor router to MyVigor website for getting more
service. Please follow the steps below to finish the router registration.

1 Please login the web configuration interface of Vigor router by typing “admin/admin”

as User Name / Password.

2 Click Support Area>>Production Registration from the home page.

3 A Login page will be shown on the screen. Please type the account and password that

you created previously. And click Login.

Vigor2120 Series User’s Guide

55

Notice: If you haven’t an accessing account, please refer to section 3.5 Creating an
Account for MyVigor on this Guide to create your own one. Please read the articles
on the Agreement regarding user rights carefully while creating a user account.

4 The following page will be displayed after you logging in MyVigor. From this page,

please click Add or Product Registration.

5 When the following page appears, please type in Nickname (for the router) and choose

the right registration date from the popup calendar (it appears when you click on the box
of Registration Date). After adding the basic information for the router, please click
Submit.

6 When the following page appears, your router information has been added to the

database.

Vigor2120

Vigor2120 Series User’s Guide

56

4 After clicking OK, you will see the following page. Your router has been registered to

myvigor website successfully.

Vigor2120 Series User’s Guide

57

TTuuttoorriiaallss aanndd A

Apppplliiccaattiioonnss

33..11 HHooww ttoo ccoonnffiigguurree sseettttiinnggss ffoorr IIPPvv66 SSeerrvviiccee iinn VViiggoorr22112200

Due to the shortage of IPv4 address, more and more countries use IPv6 to solve the problem.
However, to continually use the original rich resources of IPv4, both IPv6 and IPv4 networks
shall communicate for each other via intercommunication mechanism to complete the shifting
job from IPv4 to IPv6 gradually. At present, there are three common types of
intercommunication mechanisms:

 Dual Stack

The user can use both IPv4 and IPv6 techniques at the same time. That means adding an
IPv6 stack on the origin network layer to let the host own the communication capability
of IPv4 and IPv6.

 Tunnel

Both IPv6 hosts can communication for each other via existing IPv4 network
environment. The IPv6 packets will be encapsulated with the header of IPv4 first. Later,
the packets will be transformed and judged by IPv4 router. Once the packets arrive the
border between IPv4 and IPv6, the header of IPv4 on the packets will be removed. Then,
the packets with IPv6 address will be forwarded to the destination of IPv6 network.

 Translation

Such feature is active only for the user who uses IPv4 to communicate with other user
using IPv4 service.

Before configuring the settings on Vigor2120, you need to know which connection type that
your IPv6 service used.

Note: For the IPv6 service, you have to configure WAN/LAN settings before using the
service.

II.. CCoonnffiigguurriinngg tthhee WWAANN SSeettttiinnggss

For the IPv6 WAN settings for Vigor2120, there are five connection types to be chosen: PPP,
TSPC, AICCU, DHCPv6 Client and Static IPv6.

1. Access into the web user interface of Vigor2120. Open WAN>> Internet Access.

Choose one of the WAN interfaces as the one supporting IPv6 service. Then, click the
IPv6 button of the selected WAN.

Note: Only one WAN interface support IPv6 service at one time. In this example,
WAN1 is chosen as the one supporting IPv6 service.

Vigor2120 Series User’s Guide

58

2. In the following figure, use the drop down list to choose a proper connection type.

Different connection types will bring out different configuration page. Refer to the
following:

 PPP – Dual Stack application, IPv4 and IPv6 services can be utilized at the same

time

Choose PPP and type the information for PPPoE of IPv4.

Access into the setting page for IPv6 service, it is not necessary for you to configure
anything.

Vigor2120 Series User’s Guide

59

Click OK and open Online Status. If the connection is successful, you will get the IP
address for IPv4 and IPv6 at the same time.

Vigor2120 Series User’s Guide

60

 TSPC – Tunnel application, both IPv6 hosts communicate through IPv4 network

Choose TSPC and type the information for TSPC service.

Note: While using such mode, you have to make sure the IPv4 network connection is

normal.

(In the following figure, the TSPC information is obtained from http://gogo6.com/ after
applied for the service.)

Click OK and open Online Status. If the connection is successful, the physical
connection will be shows as follows:

Vigor2120 Series User’s Guide

61

 AICCU – Tunnel application

Choose AICCU and type the information for AICCU of IPv6.

Note: While using such mode, you have to make sure the IPv4 network connection is
normal.

(In the following figure, the AICCU information is obtained from
https://www.sixxs.net/main/

after applied for the service.)

Click OK and open Online Status. If the connection is successful, the physical
connection will be shows as follows:

Vigor2120 Series User’s Guide

62

 DHCPv6 Client

Choose DHCPv6 Client. Click one of the identity associations and type the IAID
number.

Click OK and open Online Status. If the connection is successful, the physical
connection will be shows as follows:

Vigor2120 Series User’s Guide

63

 Static IPv6

Choose Static IPv6. Type IPv6 address, Prefix Length and Gateway Address.

Click OK and open Online Status. If the connection is successful, the physical
connection will be shows as follows:

Vigor2120 Series User’s Guide

64

IIII.. CCoonnffiigguurriinngg tthhee LLAANN SSeettttiinnggss

After finished the WAN settings for IPv6, please configure the LAN settings to make the
router’s client getting the IPv6 address.

1. Access into the web user interface of Vigor2120. Open LAN>> General Setup. Click

the IPv6 button to display the following page.

Note: Only the subnet of LAN1 supports IPv6 feature.

2. In the field of Router Advertisement Server, the default setting is Enable. The client’s

PC will ask RADVD service for the Prefix of IPv6 address automatically, and generate
an Interface ID by itself to compose a full and unique IPv6 address.

3. In the field of DHCPv6 Server, when DHCPv6 service is enabled, you can assign

available IPv6 address for the client manually.

Note: When both mechanisms are enabled, the client can determine which mechanism
to be used (e.g., the default mechanism for Windows7 is RADVD).

Vigor2120 Series User’s Guide

65

IIIIII.. CCoonnffiirrmmiinngg IIPPvv66 SSeerrvviiccee RRuunn SSuucccceessssffuullllyy

1. Make sure you have get the correct IPv6 IP address. Get into MS-DOS interface and type

the command of “ipconfig”. Refer to the following figure.

From the above figure we can see IPv6 IP address has been captured by the system.

2. Use the Ping command to ping any IPv6 address indicating an IPv6 website. For

example, www.kame.net

is a website supporting IPv4 IP and IPv6 IP services. Its IPv6

address is seen with a format of 2001:200:dff:fff1:216:3eff:feb1:44d7.

After getting the above message, it means the IPv6 service has been activated
successfully.

Vigor2120 Series User’s Guide

66

3. Connect to the website for IPv6. Open a web browser and type an URL of IPv6, e.g.,

www.kame.net

. If your computer accesses into the website by using IPv6 address, you

may see a turtle dancing on the screen. If not, only a steady turtle will be seen.

If you can see a turtle dancing on the screen, that means IPv6 service is ready for you to
access and utilize.

Vigor2120 Series User’s Guide

67

33..22 HHooww ccaann II ggeett tthhee ffiilleess ffrroomm UUSSBB ssttoorraaggee ddeevviiccee ccoonnnneeccttiinngg
ttoo VViiggoorr rroouutteerr??

Files on USB storage device can be reviewed by opening USB Applicaiton>>File Explorer.
If it is necessary for you to delete, copy files on the device or write, paste files to the devcie, it
must be done through or FTP server.

1. Plug the USB device to the USB port on the router. Make sure Disk Connected appears

on the Connection Status as the figure shown below:

2. Setup a user account for the FTP service by using USB Application >>USB User

Management. Click Enable to enable FTP/Samba User account. Here we add a new
account "user1" and assign authorities “Read”, “Write” and “List” to it.

3. Click OK to save the configuration.

Vigor2120 Series User’s Guide

68

4. Make sure the FTP service is running properly. Please open a browser and type

ftp://192.168.1.1

. Use the account "user1" to login.

5. When the following screen appears, it means the FTP service is running properly.

6. Return to USB Application >> USB Disk Status. The information for FTP server will

be shown as below.

Vigor2120 Series User’s Guide

69

Now, users in LAN of Vigor2120 can access into the USB storage device by typing
ftp://192.168.1.1 on any browser. They can add or remove files / directories, depending on the
Access Rule for FTP account settings in USB Application >>USB User Management.

33..33 HHooww ttoo BBuuiilldd aa LLAANN--ttoo--LLAANN VVPPNN BBeettwweeeenn RReemmoottee OOffffiiccee aanndd
HHeeaaddqquuaarrtteerr vviiaa IIPPsseecc TTuunnnneell ((MMaaiinn MMooddee))

CCoonnffiigguurraattiioonn oonn VViiggoorr RRoouutteerr ffoorr HHeeaadd OOffffiiccee

1. Log into the web user interface of Vigor router.

2. Open VPN and Remote Access>>LAN to LAN to create a LAN-to-LAN profile.

3. Click any index number to open the configuration page. Type a name which is easy for

identification for such profile (in this case, type VPN Server), and check the box of
Enable This Profile. For Vigor router will be set as a server, the call direction shall be
set as Dial-in and set 0 as Idle Timeout.

Vigor2120 Series User’s Guide

70

4. Now navigate to the next section, Dial-In Settings to check PPTP, IPsec Tunnel and

L2TP boxes. Check the box of Specify Remote… and type the Peer VPN Server IP
(e.g., 218.242.130.19 in this case). Press the IKE Pre-Shared Key button to set the PSK;
and select Medium (AH) or High (ESP) as the security method.

5. Continue to navigate to the TCP/IP Network Settings for setting the LAN IP for remote

side.

6. Click OK to save the settings.

Vigor2120 Series User’s Guide

71

7. Open VPN and Remote Access>>Connection Management to check the dial-in

connection status (from branch office).

CCoonnffiigguurraattiioonn oonn VViiggoorr RRoouutteerr ffoorr BBrraanncchh OOffffiiccee

1. Log into the web user interface of Vigor router.

2. Open VPN and Remote Access>>LAN to LAN to create a LAN-to-LAN profile. The

following settings are for a permanent VPN connection.

3. Click any index number to open the configuration page. Type a name which is easy for

identification for such profile (in this case, type VPN Client), and check the box of
Enable This Profile. For such Vigor router will be set as a client, the call direction shall
be set as Dial-out. Check the box of Always on for a permanent VPN connection.

Vigor2120 Series User’s Guide

72

4. Now navigate to the next section, Dial-Out Settings to select the IPsec Tunnel service

and type the remote server IP/host name (e.g., 218.242.133.91, in this case). Press the
IKE Pre-Shared Key button to set the PSK; and select Medium (AH) or High (ESP)
as the security method.

5. Continue to navigate to the TCP/IP Network Settings for setting the LAN IP for the

remote side.

6. Click OK to save the settings.

Vigor2120 Series User’s Guide

73

7. Open VPN and Remote Access>>Connection Management to check the dial-in

connection status (from head office).

Vigor2120 Series User’s Guide

74

33..44 HHooww ttoo OOppttiimmiizzee tthhee BBaannddwwiiddtthh tthhrroouugghh QQooSS TTeecchhnnoollooggyy

Have you ever gotten any problems in uploading/downloading files (Voice, video or
email/data only) with the narrow/districted bandwidth you may share from the common
Internet connection line? The advanced bandwidth management technology-QoS (Quality of
Service) helps you to well allocate the bandwidth upon your demand of Voice, Video, or Data
transferring. Let's see how to get the optimum bandwidth per your request by using DrayTek
Vigor router as below.

Scenario: The Internet connection you got from ISP line is 2MB/512Kb. There are VoIP
telephony network, IPTV set top box and data server at your home. Assume you want to
allocate 30% of the bandwidth you got to VoIP demand, 50% for IPTV, 15% for mail/data,
5% for others. Let's see how easily it is to do the setting as below:

1.

Open Bandwidth Management>> Quality of Service.

2. You will get the following page. Click the Edit link for Class 1.

3.

In the following page, type a name (e.g., VoIP) for such class and click Add.

4. Check the box of ACT. Click Edit to specify the local address.

Vigor2120 Series User’s Guide

75

5. In the pop-up window, choose Range Address as the Address Type and type the start IP

address and end IP address in relational fields. Click OK to save the settings and exit the
window.

6. Click OK again to save the settings.

Vigor2120 Series User’s Guide

76

7. The class rule for VoIP has been set. Click OK to return to previous page.

8. Do the same steps to add class rules for IPTV and Data/Email with IP addresses as

shown below.

and

Vigor2120 Series User’s Guide

77

9. Assuming you get 2MB/512Kb Internet line. You can click the Setup link of WAN1 to

set up the bandwidth for different groups among VoIP, IPTV and Data/Email.

10. In the Setup page, check the box of Enable the QoS Control. Type 30, 50 and 15 in the

boxes for VoIP, IPTV and Data/Email respectively. Check the box of Enable UDP

Bandwidth Control.

Note: The rate of outbound/inbound must be smaller than the real bandwidth to

ensure correct calculation of QoS. It is suggested to set the bandwidth value for
inbound/outbound as 80% - 85% of physical network speed provided by ISP to
maximize the QoS performance.

Vigor2120 Series User’s Guide

78

11. Click OK to save the settings. The class rules for WAN1 are defined as shown below.

Vigor2120 Series User’s Guide

79

33..55 HHooww ttoo CCrreeaattee aann AAccccoouunntt ffoorr MMyyVViiggoorr

The website of MyVigor (a server located on http://myvigor.draytek.com) provides several
useful services (such as Anti-Spam, Web Content Filter, Anti-Intrusion, and etc.) to filtering
the web pages for the sake of protecting your system.

To access into MyVigor for getting more information, please create an account for MyVigor.

33..55..11 CCrreeaattee aann AAccccoouunntt vviiaa VViiggoorr RRoouutteerr

1. Click CSM>> Web Content Filter Profile. The following page will appear.

Or
Click System Maintenance>>Activation to open the following page.

Vigor2120 Series User’s Guide

80

2. Click the Activate link. A login page for MyVigor web site will pop up automatically.

3. Click the link of Create an account now.

4. Check to confirm that you accept the Agreement and click Accept.

Vigor2120 Series User’s Guide

81

5. Type your personal information in this page and then click Continue.

6. Choose proper selection for your computer and click Continue.

7. Now you have created an account successfully. Click START.

Vigor2120 Series User’s Guide

82

8. Check to see the confirmation email with the title of New Account Confirmation

Letter from myvigor.draytek.com.

9. Click the Activate my Account link to enable the account that you created. The following

screen will be shown to verify the register process is finished. Please click Login.

10. When you see the following page, please type in the account and password (that you just

created) in the fields of UserName and Password.

11. Now, click Login. Your account has been activated. You can access into MyVigor server

to activate the service (e.g., WCF) that you want.

Vigor2120 Series User’s Guide

83

33..55..22 CCrreeaattee aann AAccccoouunntt vviiaa MMyyVViiggoorr WWeebb SSiittee

1. Access into http://myvigor.draytek.com. Find the line of Not registered yet?. Then, click

the link Click here! to access into next page.

2. Check to confirm that you accept the Agreement and click Accept.

Vigor2120 Series User’s Guide

84

3. Type your personal information in this page and then click Continue.

4. Choose proper selection for your computer and click Continue.

5. Now you have created an account successfully. Click START.