i
Vigor2620 LTE Series
LTE Router
Quick Start Guide
(For RF Model)
Version: 1.0
Firmware Version: V3.8.11
(For future update, please visit DrayTek web site)
Date: April 8, 2019
ii
Intellectual Property Rights (IPR) Information
Copyrights
Trademarks
© All rights reserved. This publication contains information that is protected
by copyright. No part may be reproduced, transmitted, transcribed, stored in
a retrieval system, or translated into any language without written permission
from the copyright holders.
The following trademarks are used in this document:
Microsoft is a registered trademark of Microsoft Corp.
Windows, Windows 95, 98, Me, NT, 2000, XP, Vista, 7, 8 and Explorer are
trademarks of Microsoft Corp.
Apple and Mac OS are registered trademarks of Apple Inc.
Other products may be trademarks or registered trademarks of their
respective manufacturers.
Safety Instructions and Approval
Safety
Instructions
Read the installation guide thoroughly before you set up the router.
The router is a complicated electronic unit that may be repaired only be
authorized and qualified personnel. Do not try to open or repair the
router yourself.
Do not place the router in a damp or humid place, e.g. a bathroom.
Do not stack the routers.
The router should be used in a sheltered area, within a temperature
range of +5 to +40 Celsius.
Do not expose the router to direct sunlight or other heat sources. The
housing and electronic components may be damag ed by dire ct sunlight or
heat sources.
Do not deploy the cable for LAN connection outdoor to prevent electronic
shock hazards.
Keep the package out of reach of children.
When you want to dispose of the router, please follow local regulations on
conservation of the environment.
Warranty
We warrant to the original end user (purchaser) that the router will be free
from any defects in workmanship or materials for a period of two (2) years
from the date of purchase from the dealer. Please keep your purchase receipt
in a safe place as it serves as proof of date of purchase. During the warranty
period, and upon proof of purchase, should the product have indications of
failure due to faulty workmanship and/or materials, we will, at our discretion,
repair or replace the defective products or components, without charge for
either parts or labor, to whatever extent we deem necessary tore-store the
product to proper operating condition. Any replacement will consist of a new
or re-manufactured functionally equivalent product of equal value, and will
be offered solely at our discretion. This warranty will not apply if the produ ct
is modified, misused, tampered with, damaged by an act of God, or subjected
to abnormal working conditions. The warranty does not cover the bundled or
licensed software of other vendors. Defects which do not significantly affect
the usability of the product will not be covered by the warranty. We reserve
the right to revise the manual and online documentation and to make changes
from time to time in the contents hereof without obligation to notify any
person of such revision or changes.
i
Declaration of Conformity
Hereby, DrayTek Corporation declares that the radio equipment type Vigor262 0 is in complia nce with
Directive 2014/53/EU.
The full text of the EU Declaration of Conformity is available at the following internet address:
http://www.draytek.com.tw/ftp/Vigor2620/Document/CE/
Manufacturer: DrayTek Corp.
Address: No. 26, Fu Shing Road, HuKou Township, HsinChu Industrial Park, Hsin-Chu County,
Taiwan 303
Product: Vigor2620 Series
Frequency Information for Europe area:
2.4G WLAN 2412MHz - 2472 MHz, max. TX power: 19.98dBm *1
LTE B1[1920-1980 MHz (TX); 2110-2170 MHz (RX)]; B3[1710-1785 MHz (TX);
1805-1880 MHz (RX)]; B7[2500-2570 MHz (TX); 2620-2690 MHz (RX)];
B8[880-915 MHz (TX); 925-960 MHz (RX)]; B20[832-862 MHz (TX); 791-821
MHz (RX)]; *2
3G B1[1920-1980 MHz (TX); 2110-2170 MHz (RX)]; B8[880-915 MHz (TX); 925-960
MHz (RX)] *2
(*1: for 2.4G WLAN model; *2: for LTE model)
This product is designed for LTE, DSL and 2.4GHz WLAN network throughout the EC region.
Regulatory Information
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device may accept any interference received, including interference that may cause
undesired operation.
ii
Company name ABP International Inc.
USA Local
Representative
Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
The antenna/transmitter should be kept at least 20 cm away from human body.
Address 13988 Diplomat Drive Suite 180 Dallas TX 75234
ZIP Code 75234 E-mail rmesser@abptech.com
Contact Person Mr. Robert
Messer
Tel. 19728311600
DrayTek Vigor2620 series VDSL2/ADSL2+ routers are compliant with 47 C.F.R. Part 68.
More update, please visit www.draytek.com.
iii
TTaabbllee ooff CCoonntteennttss
1. Introduction........................................................................................................... 1
2. Package Content .................................................................................................. 2
3. Panel Explanation................................................................................................. 3
3.1 Vigor2620L / Vigor2620Le.......................................................................................................... 3
3.2 Vigor2620Ln / Vigor2620Lne......................................................................................................5
4. Hardware Installation ........................................................................................... 7
4.1 Network Connection via LTE...................................................................................................... 7
4.2 Network Connection via DSL..................................................................................................... 8
4.2 Wall-Mounted Installation........................................................................................................... 9
5. Software Configuration...................................................................................... 10
5.1 Quick Start Wizard for Network Connection............................................................................. 10
6. Customer Service............................................................................................... 13
iv
11.. IInnttrroodduuccttiioonn
Vigor2620 LTE series is a router equipped with an LTE module which allows you
to access the Internet via a SIM card.
By adopting hardware-based VPN platform and hardware encryption of
AES/DES/3DES, and hardware key hash of SHA-1/MD5, the router increases the
performance of VPN greatly and offers several protocols (such as
IPSec/PPTP/L2TP).
With multi-subnet for secure and efficient workgroup management, Vigor router
integrates IP layer QoS, NAT session/bandwidth management to help users
control works well with large bandwidth.
The object-based design used in SPI (Stateful Packet Inspection) firewall allows
users to set firewall policy with ease. CSM (Content Security Management)
provides users control and management in IM (Instant Messenger) and P2P (Peer
to Peer) more efficiency than before.
In addition, DoS/DDoS prevention and URL/Web content filter strengthen the
security outside and control inside.
1
22.. PPaacckkaaggee CCoonntteenntt
Take a look at the package content. If there is anything missed or damaged,
please contact DrayTek or dealer immediately.
Vigor Router
LTE Antenna
RJ-45 to RJ-45 Cable
(Annex B)
RJ-11 to RJ-45 Cable (Annex B)
RJ-11 to RJ-11 Cable (Annex A)
Quick Start Guide
RJ-45 Cable (Ethernet)
The type of the power adapter depends on the country that the router will be
installed.
UK-type Power Adapter
USA/Taiwan-type Power Adapter
EU-type Power Adapter
AU/NZ-type Power Adapter
Note
Important: Remove protective film before use to ensure
ventilation.
2
33.. PPaanneell EExxppllaannaattiioonn
33..11 VViiggoorr22662200LL // VViiggoorr22662200LLee
LED Status Explanation
Off The router is powered off.
(for Vigor2620L)
(for Vigor2620Le)
(for Vigor2620L)
Blinking The router is powered on and running
normally.
On The router is ready to access Internet.
Off The router is not ready to access Internet.
Blinking Slowly: The DSL connection is ready.
Quickly: The DSL connection is establishing.
On Physical line has been connected.
Blinking The connection is training.
On The LAN port is connected.
Blinking The data is transmitting through the LAN port.
On The LAN port is connected.
Blinking The data is transmitting through the LAN port.
On LTE device is connected and ready for use.
Off LTE device is not detected, or has serious
problem (e.g., no SIM card, SIM pin error, SIM
deactivated, and etc.).
Blinking Vigor device performs initial access procedure.
On SIM card is inserted into the slot and detected
by Vigor device.
Blinking No SIM card in detected.
3
Vigor2620L,
Vigor2620Le,
Interface Description
Factory Reset
Restore the default settings. Usage: Turn on the router
(ACT LED is blinking). Press the hole and keep for more than
5 seconds. When you see the ACT LED begins to blink
rapidly than usual, release the but ton. Then t he ro uter will
restart with the factory default configuration.
DSL
SIM2/SIM1
P2-P1
Connecter for accessing the Internet.
SIM card slot(s).
Connecters for local network devices.
(Vigor2620L)
P4-P1
Connecters for local network devices.
(Vigor2620Le)
ON/OFF Power Switch.
PWR Connecter for a power adapter.
4
33..22 VViiggoorr22662200LLnn // VViiggoorr22662200LLnnee
LED Status Explanation
Off The router is powered off.
(for Vigor2620Ln)
(for Vigor2620Lne)
(for Vigor2620Ln)
Blinking The router is powered on and running
normally.
On The router is ready to access Internet.
Off The router is not ready to access Internet.
Blinking Slowly: The DSL connection is ready.
Quickly: The DSL connection is establishing.
On Physical line has been connected.
Blinking The connection is training.
On The LAN port is connected.
Blinking The data is transmitting through the LAN port.
On The LAN port is connected.
Blinking The data is transmitting through the LAN port.
On LTE device is connected and ready for use.
Off LTE device is not detected, or has serious
problem (e.g., no SIM card, SIM pin error, SIM
deactivated, and etc.).
Blinking Vigor device performs initial access procedure.
On SIM card is inserted into the slot and detected
by Vigor device.
Blinking No SIM card in detected.
On Vigor device is ready for sending wireless
signal.
Off No wireless signal is sent out.
Blinking The data is transmitting via wireless
connection.
5
Vigor2620Ln,
Vigor2620Lne,
Interface
Wireless LAN
ON/OFF/WPS
Factory Reset
DSL
SIM2/SIM1
(Vigor2620Ln)
SIM1
(Vigor2620Lne)
Description
Press the button and release it within 2 seconds. When
the wireless function is ready, the green LED will be on.
Press the button and release it within 2 seconds to turn
off the WLAN function. When the wireless function is not
ready, the LED will be off.
When WPS function is enabled by web user interface,
press this button for mor e tha n 2 seconds to wait for
client’s device making network connection through WPS.
Restore the default settings. Usage: Turn on the router (ACT
LED is blinking). Press the hole and keep for more than 5
seconds. When you see the ACT LED begins to blink rapidly
than usual, release the button. Then the router will restart
with the factory default configuration.
Connecter for accessing the Internet.
SIM card slot(s).
SIM card slot(s).
P2-P1
Connecters for local network devices.
ON/OFF Power Switch.
PWR Connecter for a power adapter.
6
44.. HHaarrddwwaarree IInnssttaallllaattiioonn
This section will guide you to install the router through hardware connection and
configure the router’s settings through web browser.
Before starting to configure the router, you have to connect your devices
correctly.
44..11 NNeettwwoorrkk CCoonnnneeccttiioonn vviiaa LLTTEE
1. Install the SIM card into the card slot. The back plate of the SIM card slot
must be removed first and the direction of card notch must be on the left
side.
After installing the SIM card, fasten the back plate again.
2. Connect to your computer with a RJ-45 cable.
3. Connect one end of the power cord to the power port of this device.
Connect the other end to the wall outlet of electricity.
4. Power on the router.
5. Check the power, LTE and LAN LEDs to assure network connections.
7
44..22 NNeettwwoorrkk CCoonnnneeccttiioonn vviiaa DDSSLL
1. Connect the DSL interface to the external ADSL splitter with an ADSL line
cable.
2. Connect to your computer with a RJ-45 cable.
3. Connect one end of the power cord to the power port of this device.
Connect the other end to the wall outlet of electricity.
4. Power on the router.
5. Check the power and DSL, LAN LEDs to assure network connections.
8
44..22 WWaallll--MMoouunntteedd IInnssttaallllaattiioonn
Vigor router has keyhole type mounting slots on the underside.
1. A template is provided on the Vigor router packaging box to enable you to
space the screws correctly on the wall.
2. Place the template on the wall and drill the holes according to the
recommended instruction.
3. Fit screws into the wall using the appropriate type of wall plug.
Note
The recommended drill diameter shall be 6.5mm (1/4”).
4. When you finished about procedure, the router has been mounted on the
wall firmly.
9
55.. SSooffttwwaarree CCoonnffiigguurraattiioonn
To access Internet, please finish basic configuration after completing the
hardware installation.
55..11 QQuuiicckk SSttaarrtt WWiizzaarrdd ffoorr NNeettwwoorrkk CCoonnnneeccttiioonn
The Quick Start Wizard is designed for you to easily set up your router for
Internet access. You can directly access the Quick Start Wizard via Web User
Interface. Make sure your PC connects to the router correctly.
Note
Open a web browser on your PC and type http://192.168.1.1. A pop-up window
will open to ask for username and password. Please type “admin/admin” as the
Username/Password and click Login.
You may either simply set up your computer to get IP dynamically from
the router or set up the IP address of the computer to be the same
subnet as the default IP address of Vigor router 192.168.1.1. For the
detailed information, please refer to - Trouble Shooting of the user’s
guide.
Note
If you fail to access to the web configuration, please go to “Trouble
Shooting” on User’s Guide for detecting and solving your problem.
10
Now, the Main Screen will pop up. Click Wizards>>Quick Start Wizard.
Note
The home page will change slightly in accordance with the router you
have.
1. If your router can be under an environment with high speed NAT, the
configuration provide here can help you to deploy and use the router quickly.
The first screen of Quick Start Wizard is entering login password. After
typing the password, please click Next.
2. On the next page, please select the WAN interface that you use. If DSL
interface is used, please choose WAN1; if USB interface is used, please
11
choose LTE. Then click Next for next step. WAN1 and LTE will bring up
different configuration page. Here, we take LTE as an example.
3. Click Next to go to the following page.
12
4. Manually enter SIM PIN code and SPM Name provided by your ISP. Then click
Next for viewing summary of such connection.
5. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then,
the system status of this protocol will be shown.
6. Now, you can enjoy surfing on the Internet.
66.. CCuussttoommeerr SSeerrvviiccee
If the router cannot work correctly after trying many efforts, please contact your
dealer for further help right away. For any questions, please feel free to send
e-mail to support@draytek.com.
BBee aa RReeggiisstteerreedd OOwwnneerr
Web registration is preferred. You can register your Vigor router via
http://www.draytek.com.
FFiirrmmwwaarree && TToooollss UUppddaatteess
Due to the continuous evolution of DrayTek technology, all routers will be
regularly upgraded. Please consult the DrayTek web site for more information on
newest firmware, tools and documents. http://www.draytek.com
13
Loading...