Draw-Tite 59772, 59774 User Manual

Fitting Instructions

APE (Anchor Point Extended)

Cross Bar Kits for Track & Direct

Mounting Systems

Note: Prior to Assembly
Prior to assembling your cross bar kit check
that the kit contains all the parts you will need
to fit the cross bars. Refer to parts lists for
guidance.
Please read these instructions before assembly.

Step 1: Determine if you have a Direct or
Track mounting roof rack system. These
systems must be installed prior to installing

the cross bar kits. If it’s a Track Mounting

System (part numbers 59853, 59854, &

59855) follow steps 2 and 3. (Fig. 1) If it’s a

Direct Mounting System (part numbers
59753 & 59754) follow steps 4 and 5 (Fig. 2)

Track Systems part numbers

59853 – 59854 - 59855

Direct Mount

Bolt M6 x 24mm

Qty 4

PART No:

CARRYING CAPACITY:

Parts list

Cross Bars

End Support

Qty 4

Track Mount

Bolt M6 x 16mm

Qty 4

M8 Spring

59772, 59773,

59774

75Kgs/

165 Lbs

Qty 2

Under Cover

Qty 2

M6 Hex Nut

Brass

Qty 4

Washer

Qty 4

Vehicle’s roof

Fig. 1

Direct Systems part numbers

59753 – 59754

Vehicle’s roof

Fig. 2

Front of

vehicle

M8 Hex Nut

Qty 4

End Cap Key

Qty 4

Front of

vehicle

M8 Washer

Qty 4

Clamp Plate

Qty 4

Cross Bar End Caps

Qty 4

Bolt

M8 x 20mm

Qty 4

Tools required

13mm or adjustable wrench

Phillips screw driver

Scissors or Blade

Step 2: Installing Cross Bars on a Track Mounting
System.
A. Locate hardware bag labeled “Track Mount

Hardware”.

B. Assemble bolt M6x16 into End Support and thread

on M6 Hex nut brass onto bolt, (Fig. 3)

L Wrench

Qty 1

59772-3-4N REV 4-24-13

Printed in China

Pg 1 of 3

End Support

M6x16 Bolt

Fitting Instructions

APE (Anchor Point Extended)

Cross Bar Kits for Track & Direct

Mounting Systems

Open end of Track

PART No:

59772, 59773,

59774

CARRYING CAPACITY:

75Kgs/

165 Lbs

L Wrench-

security key

M6 Hex Nut

Brass

Fig. 3

To slide into position

do not thread nut past

end of bolt.

Fig. 4

Fig. 5

Step 3: Installing Cross Bars to the vehicle with Track Mounting System. (Continued)
A. Place an End Support and the M6 Hex Nut Brass into the open end of the Track (Fig 4.)

Ensure that the Brass Nut is engaged in the channel. Position it along the rail with the
logo facing out. Turn the bolt approx 2-3 turns with the L Wrench security key (Fig 5).
Do not tighten yet, Repeat for the other 3 End Supports.

B. Go to step 6 to continue installing cross bar.

Step 4: Installing Cross Bars on a Direct Mounting System.
A. Locate hardware bag labeled “Direct Mount Hardware”.

M6- Bolt

Cover

Philips head

M6x24 Bolt

L wrench-

security key

Fig. 6

Fig. 7

Fig. 8

Fig. 9

Step 5: Installing Cross Bars to the vehicle with Direct Mounting System. (Fig. 6)
A. Using a Philips head screw driver remove the top screw and cover from mounting

block. Covers will not be replaced while the cross bars are on the vehicle. Store
the Covers and Bolts for later replacement when cross bars are removed. (Fig. 7)

B. Place End Support on mounting block with the logo facing out. Install the M6x24

bolt through End Support and turn the bolt approx 2-3 turns with the L wrench
security key. (Fig. 8-9) Do not tighten yet, repeat for other 3 End Supports.

C. Go to step 6 to continue installing cross bar.

59772-3-4N REV 4-24-13

Printed in China

Pg 2 of 3