Draw-Tite 59508 User Manual [en, es, fr]
Product Name:
NV2
Product Code:
59508
Please read all instructions carefully before assembly, installation and/or use of this product.
Support Tubes to Hub Assembly:
Assemble Support tubes, Foam Frame Protectors, Anti-Sway Fingers and Cable Lock Loop to Hub Assembly as
shown in diagram #1 and diagram #2. Use the supplied T20 Security Torx key to fasten components with the four
(4) supplied #8-32 x 1” security screws.
#8-32 x 1 Security Torx
Support Tubes
Foam Frame
Protectors
Anti-Sway Finger
Screw
Cable Lock Loop
Hub Assembly
Diagram 1
Diagram 2
Cequent Performance Products - Plymouth, MI. USA.
Technical Service: (888) 521-0510
Cequent , a division of TriMas Corporation Pty Ltd.
20-50 Waterview Close, Dandenong South, VIC, Australia 3175
Ph:1300 888 051
www.rolaproducts.com
www.rola.com.au
59508N Rev F 01/12
PRINTED IN CHINA
Product Name:
NV2
Product Code:
59508
Please read all instructions carefully before assembly, installation and/or use of this product.
Cradle to Support Tube Assembly:
Assemble (4) Cradles and (2) Tube Caps on Support tubes as shown in diagram #3. NOTE orientation angle of
Cradles as shown in diagram #4.
Tube Cap
STOP
Note Cradle
Orientation
Cradles
Support Tube
Cradles
Diagram 4
Support Tubes
Diagram 3
Cequent Performance Products - Plymouth, MI. USA.
Technical Service: (888) 521-0510
Cequent , a division of TriMas Corporation Pty Ltd.
20-50 Waterview Close, Dandenong South, VIC, Australia 3175
Ph:1300 888 051
www.rolaproducts.com
www.rola.com.au
59508N Rev F 01/12
PRINTED IN CHINA
Product Name:
NV2
Product Code:
59508
Please read all instructions carefully before assembly, installation and/or use of this product.
Flip Shank Operation:
Your Rola (2) place bike carrier is pre-assembled with our patented flip shank design to be used with a 2” or 1
¼” receiver hitch.
Remove security pin and clip from carrier shank. Rotate shank to appropriate size for you hitch receiver. Replace
security pin and clip as shown in diagram #5 .
Clip
Cable Lock
Loops
2” Shank
1-1/4” Shank
Pull Pin
Diagram 5
Lift leaver to unlock
and open.
Rear View
Front View
Diagram 7
Cequent Performance Products - Plymouth, MI. USA.
Technical Service: (888) 521-0510
Cequent , a division of TriMas Corporation Pty Ltd.
20-50 Waterview Close, Dandenong South, VIC, Australia 3175
Ph:1300 888 051
Install 5/8” pin and clip for 2” hitch
Install ½” pin and clip for 1-1/4” hitch
Diagram 6
Diagram 8
www.rolaproducts.com
www.rola.com.au
59508N Rev F 01/12
PRINTED IN CHINA
Product Name:
NV2
Product Code:
59508
Please read all instructions carefully before assembly, installation and/or use of this product.
Diagram 9
Diagram 10
LOADING INSTRUCTIONS:
1. Load the bike onto the rack by placing front and rear bike wheel on rim slide finger (Diagram 9). When loading
multiple bikes, alternating each bike so that handle bars do not interfere with each other.
2. Secure the bikes by pulling the rim straps over the top of the bike wheel (Diagram 10). To prevent the bike from
swaying , secure front wheel to anti-sway finger as shown (Diagram 11).
3. A cable lock can be used thru the cable lock loop to secure bikes to rack.
4. Check the rim and crank straps periodically and after stopping to insure that they are still tight and that someone has
not released them. NOTE: Insure all locks are locked, that all pins are secured, and that all straps are properly
attached prior to moving the vehicle. Failure to do so will void the warranty.
Cequent Performance Products - Plymouth, MI. USA.
Technical Service: (888) 521-0510
Cequent , a division of TriMas Corporation Pty Ltd.
20-50 Waterview Close, Dandenong South, VIC, Australia 3175
Ph:1300 888 051
Diagram 11
www.rolaproducts.com
www.rola.com.au
59508N Rev F 01/12
PRINTED IN CHINA
Product Name:
NV2
Product Code:
59508
Please read all instructions carefully before assembly, installation and/or use of this product.
IMPORTANT NOTES:
• This bicycle rack has been designed to carry two (2) bikes, as long as the maximum weight on the rack does
not exceed 45 kgs or 100 lb.
• This rack is designed for typical use and applications (on paved or smooth gravel roads). Do not use this rack
on a vehicle that will be driven on rough roads or where the rack (and bikes) will be subjected to significant or
constant jarring and/or shock, or any vehicle with very stiff springs that will transfer the load shocks directly to
the rack and the bikes.
• Proper fitting and installation of this carrier to your specific vehicle is critical, and is the owner’s sole
responsibility.
• Improper use of this product may result in damage to your rack, your vehicle, your bicycles, or even other
vehicles driving behind you (as a result of colliding with or trying to avoid fallen bicycles and/or the rack).
• ROLA™ racks are coated to help prevent rust. As with any metal equipment it is recommended that
you keep the rack clean and remove road salt and debris.
• When leaving them outside for extended periods of time the finish will lose its luster. It is recommended that
when not in use the rack is stored indoors.
• Take care to add padding on any area of the bikes that touches another bike or any part of the vehicle.
Damage can and will happen (to your bikes and/or to the vehicle) if care is not taken during the loading and
transporting of your bikes, and padding used where necessary.
• Bicycle tires should be kept at least 6” away from the exhaust pipes of the vehicle. The high temperature
exhaust exiting from the exhaust pipes is hot enough to melt or damage tires. Keep all bike tires totally
away from the direct exhaust flow.
• Bikes fitted with large accessories (such as child carrying seat) will greatly increase the wind resistance
and therefore the pressure on the rack and all vehicle-mounting points. Reducing vehicle speed will reduce
the chance of any problems occurring because of this situation.
• After reading this manual, should you have any additional questions regarding the compatibility, fitting and/or
use of this rack, please call your nearest ROLA™ authorized retail dealer or Cequent Performance Products
Customer Service.
WARNING:
• Improper mounting will void the rack warranty.
• Damage to bicycles or rack due to ground clearance problems are not covered by warranty.
Cequent Performance Products - Plymouth, MI. USA.
Technical Service: (888) 521-0510
Cequent , a division of TriMas Corporation Pty Ltd.
20-50 Waterview Close, Dandenong South, VIC, Australia 3175
Ph:1300 888 051
www.rolaproducts.com
www.rola.com.au
59508N Rev F 01/12
PRINTED IN CHINA
Loading...