100W 230V
Glue Gun Kit
Stock No.83660 Part No.PT65SF
INSTRUCTIONS
1. INTRODUCTION
1.1 SPECIFICATION
Stock No............................................................ 83660
Part No............................................................ PT65SF
Rated voltage .......................................... 230V~50Hz
Rated input....................................................... 100W
2. GUARANTEE
Draper
tools have been carefully tested and
inspected before shipment and are guaranteed to be
free from defective materials and workmanship.
Should the tool develop a fault, please return the
complete tool to your nearest distributor or contact
Draper Tools Limited, Chandler's Ford, Eastleigh,
Hampshire, SO53 1YF. England.
Telephone Sales Desk: (023) 8049 4333 or Product
Help Line (023) 8049 4344.
A proof of purchase must be provided with the tool.
If upon inspection it is found that the fault occurring
is due to defective materials or workmanship, repairs
will be carried out free of charge. This guarantee
period covering parts/labour is 12 months from the
date of purchase except where tools are hired out
when the guarantee period is 90 days from the date
of purchase. The guarantee is extended to 24 months
for parts only. This guarantee does not apply to
Temperature................................................. 0–180ºC
Glue stick ............................................ 11.2 × 100mm
Weight (glue gun only)......................................270g
normal wear and tear, nor does it cover any damage
caused by misuse, careless or unsafe handling,
alterations, accidents, or repairs attempted or made
by any personnel other than the authorised Draper
warranty repair agent.
Note: If the tool is found not to be within the terms
of warranty, repairs and carriage charges will be
quoted and made accordingly.
This guarantee applies in lieu of any other guarantee
expressed or implied and variations of its terms are
not authorised.
Your Draper guarantee is not effective unless you
can produce upon request a dated receipt or invoice
to verify your proof of purchase within the
guarantee period.
Please note that this guarantee is an additional
benefit and does not affect your statutory rights.
Draper Tools Limited.
3. HEALTH & SAFETY INFORMATION
• Keep out of the reach of children.
• Do not touch the nozzle area when hot.
• In case of contact with eyes, rinse immediately
with plenty of water and seek medical advice.
• Keep away from sources of ignition.
• Do not leave the gun unattended during use.
• Do not breath vapour or spray.
• Avoid contact with hot glue. If accidental
contact occurs, do not remove glue, immerse
burn in water and seek medical advice.
• DO NOT USE THE GUN IN DAMP OR WET
CONDITIONS OR EXPOSE IT TO RAIN.
- Unplug the gun from the wall socket when
not in use.
- Never put any object in the gun other than
the glue sticks recommended.
- Never take a glue stick out once it has been
put into the gun: the resulting damage may
be irreparable.
• RECOMMENDATIONS - REPAIRS
- If the power supply cable is damaged it must
be replaced by the manufacturer, the
manufacturer's after sales service or a similarly
qualified person in order to avoid any danger.
- Should you wish to dispose of the tool always
use recognized and dedicated recycling centre.
- Children should be supervised to ensure that
they do not play with the appliance.
• WARNING: This tool must be placed on its stand
when not in use.
- The appliance is designed for domestic use.
3. ASSEMBLY AND USE
4.1 SUPPORT STAND - FIG. 1
The built in support stand allows for safe positioning of the gun
between glueing operations and for storage when not in use.
4.2 OPERATION - FIG. 2
Plug into wall socket and Insert the glue stick into the gun through the
feeder tube . Then allow glue gun to heat up (5 mins approx).
To further load the stick into the gun, squeeze the trigger several
times. Apply glue to one of the two materials and press together
within 15-20 seconds. The glue will set hard in approximately 1minute.
When the glue stick has been used, a second stick will have to be used
to push out the remains of the previous stick.
4.3 TRIGGER - FIG. 3
To start the flow of hot glue, squeeze trigger .
The trigger may require several operations initially to begin flow.
The glue sticks must be allowed to heat fully to flow properly.
WARNING: If hot glue comes into contact with skin, a serious burn may
occur.
Run burn under cold water for several minutes and seek medical
attention if required.
Residual glue in the chamber of this glue gun may result in dripping.
Ensure that work surface is suitably protected from dripping glue.
Avoid contact with the hot nozzle.
FIG.1
FIG.2
FIG.3
5. DISPOSAL
5.1 DISPOSAL
- At the end of the machine’s working life, or
when it can no longer be repaired, ensure that it
is disposed of according to national regulations.
- Contact your local authority for details of
collection schemes in your area.
In all circumstances:
drapertools.com
• Do not dispose of power tools with domestic
waste.
• Do not incinerate.
• Do not abandon in the environment.
• Do not dispose of WEEE*
as unsorted municipal waste.
* Waste Electrical & Electronic Equipment.
RDKC0216
Loading...