230V
BISCUIT JOINTER
83611
These instructions accompanying the product are the original instructions. This document is part of the product,
keep it for the life of the product passing it on to any subsequent holder of the product. Read all these
instructions before assembling, operating or maintaining this product.
This manual has been compiled by Draper Tools describing the purpose for which the product has been
designed, and contains all the necessary information to ensure its correct and safe use. By following all the
general safety instructions contained in this manual, it will ensure both product and operator safety, together
with longer life of the product itself.
AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the
product.
Whilst every effort has been made to ensure the accuracy of information contained in this manual, the Draper
Tools policy of continuous improvement determines the right to make modifications without prior warning.
1. TITLE PAGE
1.1 INTRODUCTION:
USER MANUAL FOR: 230V Biscuit Jointer
Stock No: 83611
Part No: PT8100D
1.2 REVISIONS:
Date first published February 2019.
As our user manuals are continually updated, users should make sure that they use
the very latest version.
Downloads are available from: http://drapertools.com/manuals
Draper Tools Limited
Hursley Road
Chandler’s Ford
Eastleigh
Hampshire
SO53 1YF
UK
Website: drapertools.com
Product help line: +44 (0) 23 8049 4344
General Fax: +44 (0) 23 8026 0784
1.3 UNDERSTANDING THIS MANUALS SAFETY CONTENT:
WARNING! – Information that draws attention to the risk of injury or death.
CAUTION! – Information that draws attention to the risk of damage to the product or
surroundings.
1.4 COPYRIGHT © NOTICE:
Copyright © Draper Tools Limited.
Permission is granted to reproduce this publication for personal and educational use
only. Commercial copying, redistribution, hiring or lending is prohibited.
No part of this publication may be stored in a retrieval system or transmitted in any
other form or means without written permission from Draper Tools Limited.
In all cases this copyright notice must remain intact.
2. CONTENTS
1 TITLE PAGE
1.1 INTRODUCTION .............................................................................................................2
1.2 REVISION HISTORY .......................................................................................................2
1.3 UNDERSTANDING THIS MANUAL ................................................................................2
1.4 COPYRIGHT NOTICE ......................................................................................................2
2 CONTENTS
2.1 CONTENTS......................................................................................................................3
3 WARRANTY
3.1 WARRANTY.....................................................................................................................4
4 INTRODUCTION
4.1 SCOPE ............................................................................................................................5
4.2 SPECIFICATION ..............................................................................................................5
4.3 HANDLING AND STORAGE ............................................................................................5
5 HEALTH AND SAFETY INFORMATION
5.1 GENERAL SAFETY INSTRUCTIONS FOR POWER TOOL USE ...................................6
5.2 ADDITIONAL SAFETY INSTRUCTIONS FOR BISCUIT JOINTERS...............................8
5.3 RESIDUAL RISK ..............................................................................................................9
5.4 CONNECTION TO THE POWER SUPPLY....................................................................10
6 TECHNICAL DESCRIPTION
6.1 IDENTIFICATION ........................................................................................................... 11
7 UNPACKING AND CHECKING
7.1 PACKAGING ..................................................................................................................12
7.2 WHAT’S IN THE BOX.....................................................................................................12
8 BASIC BISCUIT JOINTER OPERATIONS
8.1 ON/OFF LOCKING SWITCH .........................................................................................13
8.2 BLADE DEPTH SELECTION ........................................................................................13
8.3 HEIGHT/ANGLE ADJUSTMENT ...................................................................................13
8.4 BLADE REPLACEMENT ...............................................................................................14
8.5 CUTTING .......................................................................................................................14
8.6 DUST EXTRACTION ......................................................................................................14
9 MAINTENANCE AND TROUBLESHOOTING
9.1 SAWDUST..................................................................................................................... 15
9.2 RECOMMENDED ACCESSORIES ............................................................................... 15
9.3 PROHIBITED ACCESSORIES ...................................................................................... 15
9.4 CLEANING .................................................................................................................... 15
9.5 TROUBLESHOOTING GUIDE ...................................................................................... 16
10 OPTIONAL ACCESSORIES
10.1 OPTIONAL ACCESSORIES.......................................................................................... 17
11 DISPOSAL
11.1 DISPOSAL..................................................................................................................... 17
12 EXPLANATION OF SYMBOLS
12.1 EXPLANATION OF SYMBOLS ..................................................................................... 18
DECLARATION OF CONFORMITY .............................................................................. ENCLOSED
- 3 -- 18 -
3. WARRANTY
3.1 WARRANTY
Draper tools have been carefully tested and inspected before shipment and are guaranteed to be
free from defective materials and workmanship.
Should the tool develop a fault, please return the complete tool to your nearest distributor or
contact:
Draper Tools Limited, Chandler's Ford, Eastleigh, Hampshire, SO53 1YF. England.
Telephone Sales Desk: (023) 8049 4333 or:
Product Helpline (023) 8049 4344.
A proof of purchase must be provided.
If upon inspection it is found that the fault occurring is due to defective materials or workmanship,
repairs will be carried out free of charge. This warranty period covering labour is 12 months from
the date of purchase except where tools are hired out when the warranty period is 90 days from
the date of purchase. The warranty is extended to 24 months from the date of purchase for parts
only. This warranty does not apply to any consumable parts, any type of battery or normal wear
and tear, nor does it cover any damage caused by misuse, careless or unsafe handling,
alterations, accidents, or repairs attempted or made by any personnel other than the authorised
Draper warranty repair agent.
Note: If the tool is found not to be within the terms of warranty, repairs and carriage charges will
be quoted and made accordingly.
This warranty applies in lieu of any other warranty expressed or implied and variations of its terms
are not authorised.
Your Draper warranty is not effective unless you can produce upon request a dated receipt or
invoice to verify your proof of purchase within the warranty period.
Please note that this warranty is an additional benefit and does not affect your statutory rights.
Draper Tools Limited.
- 4 - -17 -
4. INTRODUCTION
4.1 SCOPE
Professional style wood jointing for creating solid joints in soft & hard wood, ply board, MDF &
most processed timbers. As part of our core range, this product is suitable for enthusiasts and
tradespeople alike. Any other application other than what it was intended for is considered misuse.
4.2 SPECIFICATION
Stock No...............................................................................................................................83611
Part No. .......................................................................................................................... PT8100D
Motor:
Rated voltage........................................................................................................... 230V~
Rated frequency......................................................................................................... 50Hz
Rated input................................................................................................................ 900W
Revolutions per minute (no load) ..................................................................... 11,000min
Blade:
Diameter .................................................................................................................100mm
Bore ..........................................................................................................................22mm
Thickness.................................................................................................................4.0mm
Teeth .................................................................................................................................6
Cutting depth .................................................................................................................... 0-20mm
Angle adjustment................................................................................................................... 0-90º
Sound pressure level........................................................................................................ 87dB(A)
Sound power level............................................................................................................ 98dB(A)
Vibration level....................................................................................................................2.7m/s2
Weight (machine only)...........................................................................................................3.2kg
* Continuous A-Weighted Sound Pressure Level at the workstation in accordance to and declared
according to EN60745.
** The typical A-weighted noise level determined according to EN60745.
†
When sawing in wood.
4.3 HANDLING AND STORAGE
– Care must be taken when handling this product.
● Dropping this power tool could have an effect on its accuracy and could also result in
personal injury. This product is not a toy and must be respected.
– Environmental conditions can have a detrimental effect on this product if neglected.
● Exposure to damp air can gradually corrode components.
● If the product is unprotected from dust and debris, components will become clogged.
● If not cleaned and maintained correctly or regularly, the machine will not perform at its best.
-1
- 5 -
5. HEALTH AND SAFETY INFORMATION
5.1 GENERAL SAFETY INSTRUCTIONS FOR POWER TOOL USE
When using any type of power tool there are steps that should be taken to make sure that you, as the
user, remain safe.
Common sense and a respect for the tool will help reduce the risk of injury.
Read the instruction manual fully. Do not attempt any operation until you have read and understood
this manual.
Most important you must know how to safely start and stop this machine, especially in an emergency.
Keep the work area tidy and clean. Attempting to clear clutter from around the machine during use
will reduce your concentration. Mess on the floor creates a trip hazard. Any liquid spilt on the floor
could result in you slipping.
Find a suitable location. If the machine is bench mounted, the location should provide good natural
light or artificial lighting as a replacement. Avoid damp and dust locations as it will have a negative
effect on the machine’s performance. If the machine is portable do not expose the tool to rain. In all
cases do not operate power tools near any flammable materials.
Keep bystanders away. Children, onlookers and passers by must be restricted from entering the work
area for their own protection. The barrier must extend a suitable distance from the tool user.
Unplug and house all power tools that are not in use. A power tool should never be left unattended
while connected to the power supply. They must be housed in a suitable location, away locked up and
from children. This includes battery chargers.
Do not overload or misuse the tool. All tools are designed for a purpose and are limited to what they
are capable of doing. Do not attempt to use a power tool (or adapt it in any way) for an application it is
not designed for. Select a tool appropriate for the size of the job. Overloading a tool will result in tool
failure and user injury. This covers the use of accessories.
Dress properly. Loose clothing, long hair and jewellery are all dangerous because they can become
entangled in moving machinery. This can also result in parts of body being pulled into the machine.
Clothing should be close fitted, with any long hair tired back and jewellery and neck ties removed.
Footwear must be fully enclosed and have a non-slip sole.
Wear personal protective equipment (PPE). Dust, noise, vibration and swarf can all be dangerous if
not suitably protected against. If the work involving the power tool creates dust or fumes wear a dust
mask. Vibration to the hand, caused by operating some tools for longer periods must be protected
against. Wear vibration reducing gloves and allow long breaks between uses. Protect against dust and
swarf by wearing approved safety goggles or a face shield. These are some of the more common
hazards and preventions, however, always find out what hazards are associated with the
machine/work process and wear the most suitable protective equipment available.
Do not breathe contaminated air. If the work creates dust or fumes connect the machine (if possible)
to an extraction system either locally or remotely. Working outdoors can also help if possible.
Move the machine as instructed. If the machine is hand held, do not carry it by the power supply
cable. If the product is heavy, employ a second or third person to help move it safely or use a
mechanical device. Always refer to the instructions for the correct method.
Do not overreach. Extending your body too far can result in a loss of balance and you falling. This
could be from a height or onto a machine and will result in injury.
Maintain your tools correctly. A well maintained tool will do the job safely. Replace any damaged or
missing parts immediately with original parts from the manufacturer. As applicable, keep blades sharp,
moving parts clean, oiled or greased, handles clean, and emergency devices working.
Wait for the machine to stop. Unless the machine is fitted with a safety brake, some parts may
continue to move due to momentum. Wait for all parts to stop, then unplug it from the power supply
before making any adjustments, carrying out maintenance operations or just finishing using the tool.
- 6 -
Loading...