12V
IMPACT DRIVER
70332
These instructions accompanying the product are the original instructions. This document is part of the product, keep it
for the life of the product passing it on to any subsequent holder of the product. Read all these instructions before
assembling, operating or maintaining this product.
This manual has been compiled by Draper Tools describing the purpose for which the product has been designed, and
contains all the necessary information to ensure its correct and safe use. By following all the general safety instructions
contained in this manual, it will ensure both product and operator safety, together with longer life of the product itself.
AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product.
Whilst every effort has been made to ensure the accuracy of information contained in this manual, the Draper Tools
policy of continuous improvement determines the right to make modifications without prior warning.
1. TITLE PAGE
1.1 INTRODUCTION
USER MANUAL FOR: 12V Impact Driver
Stock No: 70332
Part No: IDK12VD
1.2 REVISION HISTORY
Date first published: January 2021.
As our user manuals are continually updated, users should make sure that they use
the very latest version.
Downloads are available from: http://drapertools.com/manuals
Draper Tools Limited
Hursley Road
Chandler’s Ford
Eastleigh
Hampshire
SO53 1YF
UK
Website: drapertools.com
Product help line: +44 (0) 23 8049 4344
General Fax: +44 (0) 23 8026 0784
1.3 UNDERSTANDING THIS MANUAL’S SAFETY CONTENT
WARNING! – Information that draws attention to the risk of injury or death.
CAUTION! – Information that draws attention to the risk of damage to the product or surroundings.
1.4 COPYRIGHT © NOTICE
Copyright © Draper Tools Limited.
Permission is granted to reproduce this publication for personal and educational use only.
Commercial copying, redistribution, hiring or lending is prohibited.
No part of this publication may be stored in a retrieval system or transmitted in any other form or
means without written permission from Draper Tools Limited.
In all cases this copyright notice must remain intact.
– 2 –
2. CONTENTS
2.1 CONTENTS
1. TITLE PAGE
1.1 INTRODUCTION ................................................................................................................. 2
1.2 REVISION HISTORY ........................................................................................................... 2
1.3 UNDERSTANDING THIS MANUAL’S SAFETY CONTENT ................................................ 2
1.4 COPYRIGHT © NOTICE ..................................................................................................... 2
2. CONTENTS
2.1 CONTENTS ......................................................................................................................... 3
3. WARRANTY
3.1 WARRANTY ........................................................................................................................ 4
4. INTRODUCTION
4.1 SCOPE ................................................................................................................................ 5
4.2 SPECIFICATION ................................................................................................................. 5
4.3 HANDLING AND STORAGE ............................................................................................... 5
5. HEALTH AND SAFETY INFORMATION
5.1 GENERAL SAFETY INSTRUCTIONS FOR POWER TOOL USE ....................................... 6
5.2 ADDITIONAL SAFETY INSTRUCTIONS FOR IMPACT DRIVERS ..................................... 8
5.3 SAFETY INSTRUCTIONS FOR MAINS POWERED CHARGERS & BATTERY PACKS ... 8
5.4 CONNECTION TO THE POWER SUPPLY (CHARGER) .................................................... 9
6. TECHNICAL DESCRIPTION
6.1 IDENTIFICATION .............................................................................................................. 10
7. UNPACKING AND CHECKING
7.1 PACKAGING .......................................................................................................................11
7.2 DRAPER 12V MULTI-TOOL INTERCHANGEABLE BATTERY SYSTEM ..........................11
8. PREPARING THE IMPACT DRIVER
8.1 BATTERY CHARGING ...................................................................................................... 12
9. BASIC IMPACT DRIVER OPERATIONS
9.1 INSTALLING AND REMOVING BITS ................................................................................ 13
9.2 LED WORK LIGHT ............................................................................................................ 13
9.3 FORWARD/REVERSE SELECTOR .................................................................................. 13
9.4 TRIGGER .......................................................................................................................... 13
9.5 HOLDING THE IMPACT DRIVER ..................................................................................... 14
10. MAINTENANCE & TROUBLESHOOTING
10.1 MAINTENANCE ............................................................................................................... 15
10.2 TROUBLESHOOTING GUIDE ........................................................................................ 15
11. EXPLANATION OF SYMBOLS
11.1 EXPLANATION OF SYMBOLS ........................................................................................ 16
12. DISPOSAL
12.1 DISPOSAL ....................................................................................................................... 17
12.2 BATTERY PACK DISPOSAL INFORMATION ................................................................. 17
– 3 –
3. WARRANTY
3.1 WARRANTY
Draper tools have been carefully tested and inspected before shipment and are guaranteed to be
free from defective materials and workmanship.
Should the tool develop a fault, please return the complete tool to your nearest distributor or
contact
Draper Tools Limited, Chandler’s Ford, Eastleigh, Hampshire, SO53 1YF. England.
Telephone Sales Desk: +44 (0) 23 8049 4333 or Product Help Line +44 (0) 23 8049 4344.
A proof of purchase must be provided with the tool.
If upon inspection it is found that the fault occurring is due to defective materials or workmanship,
repairs will be carried out free of charge. This warranty period covering labour is 12 months from
the date of purchase except where tools are hired out when the warranty period is 90 days from
the date of purchase. The warranty is extended to 24 months for parts only. This warranty does not
apply to any consumable parts, any type of battery or normal wear and tear, nor does it cover any
damage caused by misuse, careless or unsafe handling, alterations, accidents, or repairs
attempted or made by any personnel other than the authorised Draper warranty repair agent.
Note: If the tool is found not to be within the terms of warranty, repairs and carriage charges will
be quoted and made accordingly.
This warranty applies in lieu of any other warranty expressed or implied and variations of its terms
are not authorised.
Your Draper warranty is not effective unless you can produce upon request a dated receipt or
invoice to verify your proof of purchase within the warranty period.
Please note that this warranty is an additional benefit and does not affect your statutory rights.
Draper Tools Limited.
– 4 –
4. INTRODUCTION
4.1 SCOPE
This cordless impact driver is designed for use with insert bits and sockets, intended for a variety
of tasks where a high level of torque is required.
This product is intended for domestic and infrequent light trade use only. Any application other
than that it was intended for, is considered misuse.
4.2 SPECIFICATION
STOCK NO ............................................................................................................................... 70332
PART NO ............................................................................................................................. IDK12VD
REVOLUTIONS PER MINUTE (NO LOAD) .............................................................. 0 – 2,500R/MIN
DRIVE SPINDLE ................................................................................................. 1/4” FEMALE HEX.
MAXIMUM TORQUE .................................................................................................................80Nm
IMPACT RATE ..............................................................................................................0 – 3,500BPM
SOUND PRESSURE LEVEL (LpA) ....................................................................... 93.5dB(A), +/- 1.5
SOUND POWER LEVEL (LWA) ...........................................................................104.5dB(A), +/- 1.5
VIBRATION LEVEL ............................................................................................................13.77M/S
WEIGHT (MACHINE ONLY) .......................................................................................................975G
BATTERY PACK:
STOCK NO ........................................................................................................................ 70308
PART NO ............................................................................................................... CB12VDLI1.5
TYPE .................................................................................................................................LI-ION
RATED VOLTAGE ................................................................................................................. 12V
RATING ............................................................................................................................. 1.5AH
2
CHARGER:
STOCK NO ........................................................................................................................ 70326
PART NO ....................................................................................................................... C12VDLI
RATED VOLTAGE ............................................................................................................. 230V~
RATED FREQUENCY .........................................................................................................50HZ
RATED INPUT ...................................................................................................................... 35W
RATED D.C. OUTPUT VOLTAGE ......................................................................................... 12V
RATED D.C. OUTPUT CURRENT ....................................................................................... 2.0A
PROTECTIVE DEVICE RATED CURRENT ............................................................................ 2A
CONSTRUCTION ..........................................................................................................CLASS II
4.3 HANDLING AND STORAGE
– Care must be taken when handling this product.
• Dropping this power tool could have an effect on its accuracy and could also result in
personal injury. This product is not a toy and must be respected.
– Environmental conditions can have a detrimental effect on this product if neglected.
• Exposure to damp air can gradually corrode components.
• If the product is unprotected from dust and debris, components will become clogged.
• If not cleaned and maintained correctly or regularly, the machine will not perform at its best.
– 5 –
5. HEALTH AND SAFETY INFORMATION
5.1 GENERAL SAFETY INSTRUCTIONS FOR POWER TOOL USE
Warning!
Read all safety warnings, instructions, illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future reference.
The term “power tools” in the warnings refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can
cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not
use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators,
ranges and refrigerators. There is an increased risk of electric shock if your body is
earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual current
device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the influence of
drugs, alcohol or medication. A moment of inattention while operating power tools may
result in serious personal injury.
b) Use personal protective equipment Always wear eye protection. Protective equipment
such as a dust mask, non-skid safety shoes, hard hat or hearing protection use for
appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position before
connecting to power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or energising power tools that have the
switch on invites accidents.
– 6 –
Loading...