Page 1
MULTI-TOOL BATTERY SYSTEM
20V
WATER PU M P
08097
These instructions accompanying the product are the original instructions. This document is part of the product,
keep it for the life of the product passing it on to any subsequent holder of the product. Read all these instructions
before assembling, operating or maintaining this product.
This manual has been compiled by Draper Tools describing the purpose for which the product has been designed,
and contains all the necessary information to ensure its correct and safe use. By following all the general safety
instructions contained in this manual, it will ensure both product and operator safety, together with longer life of the
product itself.
All photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the
product.
Whilst every effort has been made to ensure the accuracy of information contained in this manual, the Draper Tools
policy of continuous improvement determines the right to make modifications without prior warning.
Page 2
1. TITLE PAGE
1.1 INTRODUCTION:
USER MANUAL FOR: 20V Water Pump
Stock No: 08097
Part No: D20G/WP
1.2 REVISIONS:
Date first published September 2021.
As our user manuals are continually updated, users should make
sure that they use the very latest version.
Downloads are available from: http://drapertools.com/manuals
Draper Tools Limited Draper Tools Limited
Hursley Road Oude Graaf 8
Chandler’s Ford 6002 NL
Eastleigh WEERT
Hampshire Netherlands
SO53 1YF
UK
Website: drapertools.com
Product Help Line: +44 (0) 23 8049 4344
General Fax: +44 (0) 23 8026 0784
1.3 UNDERSTANDING THIS MANUALS SAFETY CONTENT:
Warning! – Information that draws attention to the risk of injury or death.
Important – Information that draws attention to the risk of damage to the product or surroundings.
1.4 COPYRIGHT © NOTICE:
Copyright © Draper Tools Limited.
Permission is granted to reproduce this publication for personal and educational use only.
Commercial copying, redistribution, hiring or lending is prohibited.
No part of this publication may be stored in a retrieval system or transmitted in any other form or
means without written permission from Draper Tools Limited.
In all cases this copyright notice must remain intact.
– 2 –
Page 3
2. CONTENTS
2.1 TABLE OF CONTENTS
1. TITLE PAGE
1.1 INTRODUCTION .......................................................................................................... 2
1.2 REVISIONS: ................................................................................................................. 2
1.3 UNDERSTANDING THIS MANUALS SAFETY CONTENT ......................................... 2
1.4 COPYRIGHT © NOTICE .............................................................................................. 2
2. CONTENTS
2.1 TABLE OF CONTENTS ...............................................................................................3
3. WARRANTY
3.1 WARRANTY ................................................................................................................. 4
4. INTRODUCTION
4.1 SCOPE ......................................................................................................................... 5
4.2 SPECIFICATION .......................................................................................................... 5
4.3 HANDLING AND STORAGE ........................................................................................5
5. HEALTH AND SAFETY INFORMATION
5.1 GENERAL SAFETY INSTRUCTIONS FOR POWER TOOL USE ............................... 6
5.2 SPECIFIC SAFETY INSTRUCTIONS FOR PUMP USE ............................................. 7
5.3 RESIDUAL RISK .......................................................................................................... 8
5.4 SAFETY INSTRUCTIONS FOR MAINS POWERED CHARGERS & BATTERY
PACKS (NOT SUPPLIED)............................................................................................ 8
5.5 CONNECTION TO THE POWER SUPPLY – CHARGER (NOT SUPPLIED) .............. 9
6. TECHNICAL DESCRIPTION
6.1 IDENTIFICATION ....................................................................................................... 10
7. UNPACKING AND CHECKING
7.1 PACKAGING .............................................................................................................. 11
7.2 WHAT’S IN THE BOX ................................................................................................ 11
7.3 D20 MULTI-TOOL INTERCHANGEABLE BATTERY SYSTEM ................................. 11
8
. ASSEMBLING THE WATER PUMP
8.1 CONNECTING THE HOSES ..................................................................................... 12
9
. BATTERY PACK (NOT SUPPLIED)
9.1 BATTERY PACK CHARGING .................................................................................... 13
9.2 BATTERY PACK PROTECTION FEATURES ............................................................ 14
9.3 BATTERY PACK CHARGE STATUS ......................................................................... 14
9.4 BATTERY LIFE EFFICIENCY AND CHARGING ADVICE ......................................... 14
10
. OPERATION AND USE
10.1 ‘PRIMING’ THE PUMP ............................................................................................... 15
10.2 SWITCHING ON ........................................................................................................ 15
10.3 PUMPING SPEEDS ................................................................................................... 15
11. MAINTENANCE AND TROUBLESHOOTING
11.1 AFTER USE ............................................................................................................... 16
11.2 MAINTENANCE ......................................................................................................... 16
11.3 TROUBLESHOOTING GUIDE ................................................................................... 16
12. DISPOSAL
12.1 DISPOSAL ................................................................................................................. 18
13. EXPLANATION OF SYMBOLS
13.1 EXPLANATION OF SYMBOLS .................................................................................. 19
– 3 –
Page 4
3. WARRANTY
3.1 WARRANTY
Draper tools have been carefully tested and inspected before shipment and are guaranteed to be
free from defective materials and workmanship.
Should the tool develop a fault, please return the complete tool to your nearest distributor or
contact:
Draper Tools Limited, Chandler’s Ford, Eastleigh, Hampshire, SO53 1YF. England.
Telephone Sales Desk: +44 (0) 8049 4333 or Product Help Line +44 (0) 23 8049 4344.
A proof of purchase must be provided with the tool.
If upon inspection it is found that the fault occurring is due to defective materials or workmanship,
repairs will be carried out free of charge. This warranty period covering parts/labour is 24 months
from the date of purchase except where tools are hired out when the warranty period is 90 days
from the date of purchase. This warranty does not apply to any consumable parts, any type of
battery or normal wear and tear, nor does it cover any damage caused by misuse, careless or
unsafe handling, alterations, accidents, or repairs attempted or made by any personnel other than
the authorised Draper warranty repair agent.
Note: If the tool is found not to be within the terms of warranty, repairs and carriage charges will
be quoted and made accordingly.
This warranty applies in lieu of any other warranty expressed or implied and variations of its terms
are not authorised.
Your Draper warranty is not effective unless you can produce upon request a dated receipt or
invoice to verify your proof of purchase within the warranty period.
Please note that this warranty is an additional benefit and does not affect your statutory rights.
Draper Tools Limited.
– 4 –
Page 5
4. INTRODUCTION
4.1 SCOPE
This product has been designed for the transfer of water. It is ideally suited to the pumping out of
garden ponds and pools where water is free of debris. It MUST NOT be used for the transfer of
fuels, antifreeze, solvents or any other non-aqueous liquids.
This product is suitable for enthusiasts and tradespersons alike. Any application other than that it
was intended for is considered misuse.
4.2 SPECIFICATION
Stock No. ................................................................................................................................. 08097
Part No. ............................................................................................................................. D20G/WP
Motor:
Rated voltage ............................................................................................................... 20V
Rated power .....................................................................................................................180W
Max. pressure ........................................................................................................................... 2.2bar
Max. grain size ...................................................................................................................... _<0.5mm
Max. flow rates and heights/depths ....................................................................................................
1. Normal pumping mode:
Max. height/depth ......................................................................................................... 22M
Max. flow rate .......................................................................................................... 2800L/h
2. ‘Eco’ pumping mode: ............................................................................................................
Max. height/depth ......................................................................................................... 15M
Max. flow rate .......................................................................................................... 2000L/h
Inlet pipe connectionØ ........................................................................................................ G1(1
Moisture ingress protection rating .............................................................................................. IPX4
Weight (product only) ................................................................................................................ 2.4kg
1⁄4")
4.3 HANDLING AND STORAGE
– Care must be taken when handling this product. Dropping this power tool could have an effect
on its accuracy and could also result in personal injury. This product is not a toy and must be
respected.
– Environmental conditions can have a detrimental effect on this product if neglected. Exposure
to damp air can gradually corrode components. If the product is unprotected from dust and
debris, components will become clogged. If not cleaned and maintained correctly or regularly,
the machine will not perform at its best.
– 5 –
Page 6
5. HEALTH AND SAFETY INFORMATION
5.1 GENERAL SAFETY INSTRUCTIONS FOR POWER TOOL USE
Warning! Read all safety warnings, instructions, illustrations and specifications provided
with this power tool. Failure to follow all instructions listed below may result in electric shock, fire
and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tools” in the warnings refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or
fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can
cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not
use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators,
ranges and refrigerators. There is an increased risk of electric shock if your body is
earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual current
device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the influence of
drugs, alcohol or medication. A moment of inattention while operating power tools may
result in serious personal injury.
b) Use personal protective equipment Always wear eye protection. Protective equipment
such as a dust mask, non-skid safety shoes, hard hat or hearing protection use for
appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position before
connecting to power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or energising power tools that have the
switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a
key left attached to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better
control of the power tool in unexpected situations.
– 6 –
Page 7
5. HEALTH AND SAFETY INFORMATION
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing
away from moving parts. Loose clothes, jewellery or long hair can be caught in moving
parts.
g) If devices are provided for the connection of dust extraction and collection facilities,
ensure these are connected and properly used. Use of dust collection can reduce
dust-related hazards.
h) Do not let familiarity gained from frequent use of tools allow you to become
complacent and ignore tool safety principles. A careless action can cause severe injury
within a fraction of a second.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application. The
correct power tool will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power tool that
cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or remove the battery pack, if
detachable, from the power tool before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
e) Maintain power tools and accessories. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired before use. Many accidents are
caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended could result
in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow for safe handling and control of the tool in
unexpected situations.
5) Service
a) Have your power tool serviced by a qualified repair person using only identical
replacements parts. This will ensure that the safety of the power tool is maintained.
5.2 SPECIFIC SAFETY INSTRUCTIONS FOR PUMP USE
Have this tool repaired by a qualified person. This tool is designed to confirm to the relevant
international and local standards and as such should be maintained and repaired by someone
qualified; using only original parts supplied by the manufacturer: This will ensure the tool remains
safe to use.
− Surface mounted pumps should always be transported and stored horizontally on the base plate.
− Always ensure that your hands are dry when connecting and disconnecting the battery pack or
when connecting the battery pack charger to the mains power supply.
− NEVER operate the pump dry.
− The area being pumped should be kept clear, nobody should enter area whilst the pump is
operating.
– 7 –
Page 8
5. HEALTH AND SAFETY INFORMATION
5.3 RESIDUAL RISK
Important: Although the safety instructions and operating manuals for our tools contain extensive
instructions of safe working with power tools, every power tool involves a certain residual risk
which can not be completely excluded by safety mechanisms. Power tools must therefore always
be operated with caution!
5.4 SAFETY INSTRUCTIONS FOR MAINS POWERED CHARGERS & BATTERY PACKS (NOT SUPPLIED)
– The charger (not supplied) is for indoor use only.
– Prior to plugging the charger in to the supply, check that the plug and the cable are in good
repair. If either are damaged, have the defective item replaced immediately by a suitably
qualified person. If the casing of the battery charger is damaged, it is good policy to have the
charger checked over by a suitably qualified person.
– Only use a correctly rated mains outlet to provide power, do not plug into site generators, attach to
engine generators or D.C. sources. Do not use a mains socket outlet that is not switched.
– Use the correct Draper charger in conjunction with it’s corresponding battery pack (consult the
Draper website for more information or to find your local Draper stockist).
– Do not charge any other batteries with Draper chargers. Any other application is considered misuse.
– Do not attempt to charge battery packs that are too hot (over 30ºC) or too cold (under 5ºC), if
these conditions apply set the battery pack aside to “normalise” before proceeding with the
charging operation.
– Set up the charger and cable in a safe place where it won’t be knocked, tripped over, stepped
on, etc. and where it is well ventilated. Make sure the ventilation slots in the charger case are
not obstructed, plug the charger into the socket outlet.
– Inspect the battery pack for damage, if it is undamaged, plug it into the charger, ensuring the
correct orientation. (Most chargers and batteries have ‘keys’ etc, to make sure the battery pack
is not inserted incorrectly, if you are having to ‘force’ the battery pack into the charger, the
chances are you have it the wrong way round, check and try again.)
– Switch the charger on and check that the correct indicators illuminate, allow the battery pack to
charge (see the specific instructions for your charger). Once charging is complete, switch the
charger off, remove the battery pack and store, repeat the procedure if you have more than
one battery pack to charge.
Caution: When the battery charger has been continuously used, the battery charger will be hot.
Once the charging has been completed, give 15 minutes rest until the next charge.
– After charging is complete, unplug the charger from the socket outlet by pulling on the plug. Do
not pull on the cable. Store the charger in a dry secure place.
– If, when the charger was switched on, the correct indications did not occur, leave for two or
three minutes to allow the charger to stabilise, if the correct indications occur, allow the
charging cycle to proceed as normal. If no indication appears at all, switch off, remove the
battery pack, unplug the charger, check that the charger contacts and the battery contacts are
clean and repeat the process. If there is still no indication, switch off, remove the battery pack,
unplug the charger and check the fuse. If the fuse is blown, replace and repeat the process. If
the fuse blows again, or if the fuse was intact, attempt no further action. Refer the charger to a
suitably qualified person for repair.
Battery packs
– Before charging, read the instructions.
– For indoor use. Do not expose to rain.
– Only use Draper D20 battery packs with this product. Consult your Draper stockist for details.
– 8 –
Page 9
5. HEALTH AND SAFETY INFORMATION
– Do not charge any other manufacturer’s battery packs using Draper chargers. Any other
application is considered misuse.
– The battery must be removed from the appliance before it is recycled.
– The charger must be disconnected from the supply mains when removing the battery.
– The battery is to be disposed of in-line with local authority procedures.
– Do not use any other than the designated Draper batteries/chargers with this product.
– Do not crush, open or burn the battery. Exposure to potentially harmful materials may occur.
– In case of fire use CO2 or dry chemical extinguisher.
– Do not expose to high temperatures >50°C. The battery may degrade at high temperatures.
– Charge battery in conditions between 5°C to 30°C with the specified charger designed for this
battery.
– Do not use battery if it has been stored at 5°C or less. Allow it to “normalise” at room
temperature before usage/charging.
Warning! Leaking battery packs
– The electrolyte in battery packs is corrosive. Avoid contact with the skin.
– If contact is made, flush the area with running water, pat dry and seek medical attention and
advice at the earliest opportunity.
– Inform medical personnel that the contaminant is a “high alkaline, corrosive liquid”.
– If electrolyte comes into contact with the eyes, flush with copious amounts of water only.
Seek medical attention immediately, relaying the information above.
5.5 CONNECTION TO THE POWER SUPPLY – CHARGER (NOT SUPPLIED)
Caution: Risk of electric shock. Do not open.
The battery pack (not supplied) for this appliance is used in conjunction with a charger (also not
supplied) that is fitted with a moulded 3 pin mains plug for your safety. The value of the fuse fitted
is marked on the pin face of the plug.
Should the fuse need replacing, ensure the substitute is of the correct rating, approved to BS1362
and ASTA or BSI Kite marked.
ASTA
BSI
The fuse cover is removable with a small plain slot screwdriver. Ensure the fuse cover is replaced
before attempting to connect the plug to an electrical outlet. If the cover is missing, a replacement
must be obtained or the plug replaced with a suitable type.
If a replacement plug is to be fitted this must be carried out by a qualified electrician.
The damaged or incomplete plug, when cut from the cable should be disabled to prevent
connection to a live electrical outlet.
This appliance is Class II
on the rating label and compatible with the plug fitted.
If an extension lead is required, use an approved and compatible lead rated for this appliance.
Follow all the instructions supplied with the extension lead.
†
Double insulated : This product requires no earth connection as supplementary insulation is
applied to the basic insulation to protect against electric shock in the event of failure of the basic
insulation.
Important
If using an extension lead, follow the instructions that came with your lead regarding
maximum load while cable is wound. If in doubt, ensure that the entire cable is unwound.
Using a coiled extension lead will generate heat which could melt the lead and cause a fire.
†
and is designed for connection to a power supply matching that detailed
– 9 –
Page 10
6. TECHNICAL DESCRIPTION
6.1 IDENTIFICATION
(3) (2) (1)
(4)
(12)
(11) (10)
(6)(5)
(1) Water delivery outlet connection.
(2) Priming inlet.
(3) Filter housing cap.
(4) Inlet connection.
(5) Drain outlet valve.
(6) Pump motor housing.
(7) ON/OFF/pump speed selection switch.
(8) Battery charge Indicator lights.
(7) (8) (9)
(9) Battery pack housing.
(10) Battery pack housing lid.
(11) Battery pack housing lid catch.
(12) Carry handle.
– 10 –
Page 11
7. UNPACKING AND CHECKING
7.1 PACKAGING
Carefully remove the product from the packaging and examine it for any sign of damage that may
have happened during shipping. Lay the contents out and check them against the parts shown
below. If any part is damaged or missing, please contact the Draper Help Line (the telephone
number appears on the Title page) and do not attempt to use the product.
The packaging material should be retained at least during the warranty period, in case the
machine needs to be returned for repair.
Warning!
− Some of the packaging materials used may be harmful to children. Do not leave any of these
materials in the reach of children.
− If any of the packaging is to be thrown away, make sure they are disposed of correctly,
according to local regulations.
7.2 WHAT’S IN THE BOX
As well as the main product, there are several parts not fitted or attached to it.
(13)
(14) (15)
(13) 2M Suction hose.
(14) 1 1⁄ 4" Suction hose connector.
(15) Outlet hose connector.
7.3 D20 MULTI-TOOL INTERCHANGEABLE BATTERY SYSTEM
The D20 range of tools are a range of tools suitable for enthusiasts
and tradespersons alike, featuring a wide array of machines all
running from the same range of batteries. Many different capacity
batteries are available making sure you can balance tool weight
with longevity and find a battery that meets your needs. To find out the latest range of accessories
including batteries and chargers please consult the Draper website for more information or to find
your local Draper stockist.
– 11 –
MULTI-TOOL BATTERY SYSTEM
Page 12
8. ASSEMBLING THE WATER PUMP
8.1 CONNECTING THE HOSES – FIGS. 1 – 4
Note: Remove the battery pack from the water
pump before carrying out any adjustments,
servicing or maintenance.
− Connect the 1 1⁄4" Suction hose connector.
(14)into the suction inlet (4).
− Attach the suction hose to the suction hose
connector. Tighten by hand only. Draper Tools
recommends wrapping a length of PFTE tape
around the connector thread to prevent
leakages. Wrap the tape against the direction
of the thread for a tighter seal.
− Note: In order to reduce the suction time, it is
advisable to fill the suction hose with liquid
before connecting it to the pump.
− Connect the outlet hose adaptor (15)into the
water delivery outlet (4).
− Attach a suitable outlet hose with a ‘snap fit’
connection ((16)as seen in Fig.4) onto the
outlet hose adaptor (15). Note: The outlet hose
should be able to withstand the maximum
delivery capacity of the pump.
FIG.
FIG.
(14)
1
(1)
2
(15)
– 12 –
3
FIG.
(13) (14)
4 FIG.
(4)
(16)
(15)
Page 13
9. BATTERY PACK (NOT SUPPLIED)
9.1 BATTERY PACK CHARGING –
FIGS. 5 – 6
This power product is supplied “bare”, without
battery pack or charger. Compatible batteries,
chargers and accessories are available through
Draper Tools stockists.
Important: Only Draper designated battery packs
and chargers can be used in conjunction with this
product. Use of any other third party battery packs/
chargers with this product is considered misuse
and will invalidate the product’s warranty.
Once connected to the mains supply, recharging of
the battery can be left generally unsupervised,
requiring minimal attention. Complex circuit
construction monitors the battery condition,
adjusting the recharge current to suit. When the
recharge cycle is complete, to maintain the full
capacity, a low output current will continue as
required.
Warning! Check the condition of the charger and
battery prior to each charge. If there is any sign of
damage then do not commence charging, seek
advice from Draper Tools.
The battery pack is supplied un-charged and must
be charged before initial use.
To charge the battery pack (17), it must first be
removed from the tool.
To release the battery pack:
– Press the battery release button (17.1) and gently slide the battery pack off (Fig.5).
– Plug the battery charger (18)unit into a 230V/AC 13amp three pin supply socket.
– The red LED(18.1) will illuminate to show the charger has power.
– Slide the battery into the charger (the battery is shaped to fit into the charger one way only.
– After a few seconds delay, the red LED (18.1) will flash to show that charging has begun, then
illuminate solid red.
– Whilst the battery is charging, the green LED (18.2) will flash, (the red LED will go from
flashing to constant red.
– When the battery is fully charged when the green LED stops flashing and remains a constant
green. The red LED will extinguish.
Caution: Do not pull the plug out of the power supply by pulling on the cord. Make sure to grasp
the plug when removing from power supply to avoid damaging the cord.
To remove the battery from the battery charger:
– Supporting the battery charger with hand, pull out the battery from the battery charger.
Caution: If the battery charger has been in continuous use it will be hot. Once the charging has
been completed, leave the charger 15 minutes to cool until next use. If the battery is charged
when it is warm due to battery use or exposure to sunlight, the battery will not be recharged. In
such a case, let the battery cool before charging.
If the red indicator flickers rapidly at 0.2 second intervals, check or and remove any foreign objects
in the charger’s battery slot. If there are no foreign objects, it is probable that the battery or
FIG.
FIG.
The above and following photographs show Draper
D20 4Ah battery pack (Stock No. 55858) and Draper
D20 ‘Fast’ battery charger (Stock No. 55913)
(17.1)
(17)
5
(18.1)
(18)
(18.2)
6
– 13 –
Page 14
9. BATTERY PACK (NOT SUPPLIED)
charger is malfunctioning. Allow battery/charger to
normalise and try again. If a fault remains after
trying this then contact Draper Tools.
9.2 BATTERY PACK PROTECTION FEATURES
Overcharging protection: This feature that
ensures that the battery pack can never be
overcharged. When the battery pack reaches full
charge capacity, the transformer/charger will
automatically shut off, protecting the internal
components from being damaged.
Over-discharging protection: This feature will
stop the battery pack from discharging beyond the
recommended lowest safety voltage.
Overheating protection: The battery pack
contains an internal thermistor cut-off sensor which
shuts off the battery pack should it become too hot
during operation. This can happen if the tool is
overloaded or being used for extended periods. Up
to 30 minutes cooling time may be required,
depending on ambient temperature.
Current protection: Should the battery be
overloaded and the maximum current draw be
exceeded, the battery will shut off to protect the
internal components. The battery pack will resume
working once excessive current draw has returned
to normal, safe level.
Short circuit protection: If, for any reason, the
battery pack was to short circuit, the short circuit
protection would immediately stop the battery pack
from operating.
9.3 BATTERY PACK CHARGE STATUS – FIGS. 7 – 8
To display the amount of charge left in the battery
pack, press the charge level indicator button (17.2).
9.4 BATTERY LIFE EFFICIENCY AND CHARGING ADVICE
– Avoid recharging at high temperatures. A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after use, its internal chemical substance will
deteriorate, and the battery life will be shortened. Leave the battery and recharge it after it has
cooled for a while.
– The battery should only be used and/or charged when battery temperature is between 5°C and
30°C.
– The battery needs to be warmed-up or cooled down in order to prevent damage to the
batteries internal components,
Note: If battery is too hot or too cold, allow it to ‘normalise’ before use or charging.
Note: Failure to warm up or cool down a battery could result in serious damage to the battery,
charger and user.
(17.2)
7 FIG.
Charge level
indicator
8 FIG.
Amount of charge
remaining
0 – 10%
10 – 25%
25 – 50%
50 – 75%
75 – 100%
– 14 –
Page 15
10. OPERATION AND USE
10.1 ‘PRIMING’ THE PUMP – FIG.9
− Position the pump on flat and firm surface.
− Before operating the pump, it should be ‘primed’
with water, which is added through the priming
hole (2).
− Block off the outlet hose end of the pump so that
no water can drain out.
− Remove the screw-cap of the priming inlet
− Pour the water in through the priming hole slowly
and gradually until the water is overflowing from
the inlet hole.
10.2 SWITCHING ON
− The suction hose should be airtight, or air in the
hose will block the suction action of the liquid.
− The inlet of the suction hose should always be
submerged into the water in order to avoid
dry-running of the pump when the liquid level falls
(Fig.10).
− Make sure the suction hose does not lift up above
the pump, otherwise bubbles formed in the hose
might block the flow.
− Open any shut-off valves in the outlet hose
(injection nozzle, valves, etc.).
− Insert the battery pack.
− Start the pump by pressing the ON/OFF/pump
speed selection rocker switch (7).
10.3 PUMPING SPEEDS – FIG.11
The pump has two operating speeds activated via
the ON/OFF/pump speed selection rocker switch (7):
o OFF
| Normal pumping mode:
• Max. height/depth: 22M
• Max. flow rate: 2800L/h
Typical running time using a Draper D20
4Ah battery pack: 27 mins.
|| ‘Eco’ pumping mode:
• Max. height/depth: 15M
• Max. flow rate: 2000L/h
Typical running time using a Draper D20
4Ah battery pack: 1hr.
FIG.
FIG.
FIG.
(2)
9
10
(7)
11
– 15 –
Page 16
11. MAINTENANCE AND TROUBLESHOOTING
11.1 AFTER USE
− Switch off the pump by pressing the ON/OFF switch.
− Remove the battery pack.
− Drain remaining water in the pump through the drain outlet.
− Put the pump into storage after having been flushed through with clean water.
− Remove the filter housing cap, followed by the filter element within.
− Remove any particles of grit from the filter and rinse in clean water.
11.2 MAINTENANCE
Regular inspection and cleaning reduces the necessity for maintenance operations and will keep
your tool in good working condition.
The pump is basically maintenance free. To ensure a long service life, however, we recommend
regular checks and care.
Warning! Before any maintenance or adjustment, switch off the pump and remove the battery
pack.
If the pump is not going to be used for a long time or has to be removed for the winter months,
rinse it out with water, empty it completely and allow it to dry.
− If there is a risk of frost, the pump must be completely empty and dry.
− After long periods of non-use, make sure the rotor turns correctly by briefly switching the pump
on and off.
− If the pump becomes blocked, connect the pressure line to the water line and remove the
intake hose. Open the water line, Switch on the pump several times for approx. 2 seconds.
Most blockages can be removed in this way.
Warning! The pump must never be allowed to run dry!
11.3 TROUBLESHOOTING GUIDE
Problem Possible Cause Remedy
The pump doesn’t start or
suddenly stops.
1. Power off.
2. Battery pack damaged. 2. Replace the battery pack..
3. Other defects. 3. Contact your local Draper
– 16 –
1. Replace/reset 13 amp
time delay fuse or circuit
breaker.
Tools service agent, or
Draper Tools for fault
finding/repair.
Page 17
11. MAINTENANCE AND TROUBLESHOOTING
11.3 TROUBLESHOOTING GUIDE (continued)
Problem Possible Cause Remedy
Insufficient flow or no flow. 1. Dirty liquid and/or liquid
The pump only runs for a
short period of time.
containing other abrasive
substances may reduce
the pumping capacity.
2. Hose/Pipe/Filter clogged. 2. Unblock the hose/ Clean
3. Hose/piping system
damaged.
4. There is air in the pump
chamber.
5. The joints of the suction
hose are not sealed.
6. Incorrect saw blade
selection.
1. The impeller may be
damaged due to a
blockage within the pump,
causing it to overheat and
cut out.
1. Clean the filter. If needed,
return the product to
Draper Tools or an
authorised service agent
for repair
the filter.
3. Contact your nearest
Draper Tools stockist for
replacement hose.
4. ‘Prime’ the pump,
following the procedure
shown in section 9.1 on
page15.
5. Replace joints and make
sure the connections are
securely sealed.
6. Seek advice on suitable
saw blades.
1. Check the pump for
visible signs of a
blockage. If the blockage
is easily cleared, allow
pump to cool and then
re-start. If problem
persists return the pump
to your local Draper Tools
service agent, or Draper
Tools for fault finding/
repair.
2. Intervention of the thermal
overload switch.
– 17 –
2. Make sure the fluid being
pumped is not too dense,
causing the motor to
overheat.
3. Make sure the
temperature of the water
is not too high.
4. Make sure there is no
solid body obstructing the
impeller.
Page 18
12. DISPOSAL
12.1 DISPOSAL
– At the end of the machine’s working life, or when it can no longer be repaired, ensure that it is
disposed of according to national regulations.
– Contact your local authority for details of collection schemes in your area.
In all circumstances:
• Do not dispose of power tools with domestic waste.
• Do not incinerate.
• Do not dispose of WEEE* as unsorted municipal waste.
* Waste Electrical & Electronic Equipment.
– 18 –
Page 19
13. EXPLANATION OF SYMBOLS
13.1 EXPLANATION OF SYMBOLS
Read the instruction manual.
Wear face mask and safety
glasses.
Wear ear defenders.
Do not abandon into the
environment.
Keep out of the reach of children.
Warning!
‘Eco’ mode: Max. pumping depth
(Meters) and flow rate (Litres per
hour).
‘Normal’ mode: Max. pumping
depth (Meters) and flow rate
(Litres per hour).
98
Rated voltage.
Class II construction
(Double insulated).
WEEE –
Waste Electrical & Electronic Equipment.
Do not dispose of Waste Electrical & Electronic
Equipment in with domestic rubbish.
Continuous A-Weighted Sound
Pressure Level (example shown).
dB
UK Conformity Assessed.
European conformity.
Max. pressure.
Max. grain size (i.e. less than or
equal to 0.5mm).
Net product weight
(example shown).
Moisture ingress protection rating.
– 19 –
Page 20
CONTACTS
Draper Tools Limited
UK: Hursley Road, Chandler’s Ford, Eastleigh,
Hampshire. SO53 1YF. U.K.
EU: Oude Graaf 8
6002 NL Weert (NL)
Help Line: (023) 8049 4344
Sales Desk: (023) 8049 4333
Internet: drapertools.com
E-mail: sales@drapertools.com
General Enquiries: (023) 8026 6355
Service/Warranty Repair Agent:
For aftersales servicing or warranty repairs, please contact the
Draper Tools Help Line for details of an agent in your local area.
YOUR DRAPER STOCKIST
TACH0921
©Published by Draper Tools Limited.
No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means,
electronic, mechanical photocopying, recording or otherwise without prior permission in writing from Draper Tools Ltd.
Loading...