Draper Tools 04176, 04175, 04174 Instructions

DIESEL HEATER

04174, 04175 & 04176

04176



04175

04174

These instructions accompanying the product are the original instructions. This document is part of the product, keep
it for the life of the product passing it on to any subsequent holder of the product. Read all these instructions before
assembling, operating or maintaining this product.

This manual has been compiled by Draper Tools describing the purpose for which the product has been designed,
and contains all the necessary information to ensure its correct and safe use. By following all the general safety
instructions contained in this manual, it will ensure both product and operator safety, together with longer life of the
product itself.

All photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of
the product.

Whilst every effort has been made to ensure the accuracy of information contained in this manual, the Draper Tools
policy of continuous improvement determines the right to make modifications without prior warning.

1. TITLE PAGE

1.1 INTRODUCTION:

USER MANUAL FOR: DIESEL HEATERS
Stock nos. 04174, 04175, 04176.
Part nos. DSH58, DSH68, DSH108

1.2 REVISIONS:

Date first published June 2021.

As our user manuals are continually updated, users should make
sure that they use the very latest version.

Downloads are available from: http://drapertools.com/manuals

Draper Tools Limited Draper Tools Limited
Hursley Road Oude Graaf 8
Chandler’s Ford 6002 NL
Eastleigh WEERT
Hampshire Netherlands
SO53 1YF
UK

Website: drapertools.com
Product Help Line: [phone]
General Fax: [phone]

1.3 UNDERSTANDING THIS MANUAL’S SAFETY CONTENT:

Warning! – Information that draws attention to the risk of injury or death.
Caution! – Information that draws attention to the risk of damage to the product or surroundings.

1.4 COPYRIGHT © NOTICE:

Copyright © Draper Tools Limited.
Permission is granted to reproduce this publication for personal and educational use only.
Commercial copying, redistribution, hiring or lending is prohibited.
No part of this publication may be stored in a retrieval system or transmitted in any other form or

means without written permission from Draper Tools Limited.
In all cases this copyright notice must remain intact.

– 2 –

2. CONTENTS

2.1 CONTENTS

1. TITLE PAGE

1.1 INTRODUCTION .......................................................................................................... 2

1.2 REVISION HISTORY ................................................................................................... 2

1.3 UNDERSTANDING THIS MANUAL ............................................................................. 2

1.4 COPYRIGHT NOTICE ................................................................................................. 2

2. CONTENTS

2.1 CONTENTS ................................................................................................................. 3

3. GUARANTEE

3.1 GUARANTEE ............................................................................................................... 4

4. INTRODUCTION

4.1 SCOPE ......................................................................................................................... 5

4.2 SPECIFICATION .......................................................................................................... 5

4.3 HANDLING & STORAGE ............................................................................................. 5

5. HEALTH & SAFETY INFORMATION

5.1 GENERAL HEATER SAFETY WARNINGS .............................................................. 6-8

5.2 CONNECTION TO THE POWER SUPPLY.................................................................. 9

6. TECHNICAL DESCRIPTION

6.1 IDENTIFICATION ....................................................................................................... 10

7. UNPACKING & CHECKING

7.1 PACKAGING ...............................................................................................................11

8. ASSEMBLING THE HEATER

8.1 HANDLE ..................................................................................................................... 12

8.2 WHEEL AND HANDLE............................................................................................... 12

9. OPERATING THE HEATER

9.1 STARTING HEATER .................................................................................................. 13

9.2 TO STOP HEATER .................................................................................................... 13

9.3 TO RESTART THE HEATER ..................................................................................... 13

10. STORING & TRANSPORTING THE HEATER

10.1 STORING & TRANSPORTING THE HEATER........................................................... 14

11. MAINTENANCE

11.1 FUEL/FUEL TANK ...................................................................................................... 15

11.2 AIR FILTERS .............................................................................................................. 15

11.3 FAN BLADES ............................................................................................................. 15

11.4 NOZZLES ................................................................................................................... 15

11.5 SPARK PLUG ............................................................................................................ 16

11.6 PHOTOCELL .............................................................................................................. 16

11.7 FUEL FILTER ............................................................................................................. 16

11.8 PUMP ROTOR ........................................................................................................... 17

11.9 PUMP PRESSURE ADJUSTMENT ........................................................................... 17

11.10 WIRING DIAGRAM .................................................................................................... 18

12. TROUBLESHOOTING

12.1 TROUBLESHOOTING GUIDE .............................................................................. 19-20

13. DISPOSAL

13.1 DISPOSAL ................................................................................................................. 21

DECLARATION OF CONFORMITY ENCLOSED

– 3 –

3. GUARANTEE

3.1 GUARANTEE

Draper tools have been carefully tested and inspected before shipment and are guaranteed to be
free from defective materials and workmanship.

Should the tool develop a fault, please return the complete tool to your nearest distributor
or contact:

Draper Tools Limited, Chandler’s Ford, Eastleigh, Hampshire, SO53 1YF. England.
Telephone Sales Desk: [phone] or Product Helpline [phone].

A proof of purchase must be provided with the tool.
If upon inspection it is found that the fault occurring is due to defective materials or workmanship,

repairs will be carried out free of charge. This guarantee period covering parts/labour is 12 months
from the date of purchase except where tools are hired out when the guarantee period is 90 days
from the date of purchase. This guarantee does not apply to normal wear and tear, nor does
it cover any damage caused by misuse, careless or unsafe handling, alterations, accidents,
or repairs attempted or made by any personnel other than the authorised Draper warranty
repair agent.

Note: If the tool is found not to be within the terms of warranty, repairs and carriage charges will
be quoted and made accordingly.

This guarantee applies in lieu of any other guarantee expressed or implied and variations of its
terms are not authorised.

Your Draper guarantee is not effective unless you can produce upon request a dated receipt or
invoice to verify your proof of purchase within the guarantee period.

Please note that this guarantee is an additional benefit and does not affect your statutory rights.

Draper Tools Limited.

– 4 –

4. INTRODUCTION

4.1 SCOPE

This heater is designed to heat large, semi-open areas by means of combustion of Diesel or
Kerosene fuel, and is electrically operated.

This product is suitable for the enthusiasts and tradespersons alike. Any application other than that
it was intended for, is considered misuse.

4.2 SPECIFICATION

Stock no. .......................................04174 .............................04175 ............................. 04176

Part no. .........................................DSH58 ............................ DSH68 .......................... DSH108

Motor:

Rated voltage ..................220-240V~ ...................... 220-240V~ ..................... 220-240V~

Rated frequency .................. 50Hz ...............................50Hz ...............................50Hz

Rated input .......................... 200W .............................. 220W .............................. 225W

Heat output ......................... 51,200BTU/15kW ...........68,250BTU/20kW .......... 102,300BTU/30kW

Air flow ....................................... 400m3/hr .........................450m3/hr ......................... 600m3/hr

Fuel .............................................Diesel .............................Diesel ............................. Diesel

Diesel consumption ................... 1.4Ltrs/hr ....................... 1.87Ltrs/hr ....................... 2.8Ltrs/hr

Tank capacity ................................ 19Ltr ...............................19Ltr ............................... 33Ltr

Weight ...........................................15kg .............................. 16.5kg .............................. 24kg

Dimensions (approx.) ........ 700 × 310 × 430mm .......840 × 390 × 490mm .......950 × 480 × 590mm

4.3 HANDLING & STORAGE

− This machine should be stored in a dry location and in its box. Avoid storing this machine in
areas prone to damp or humidity.

− Remove residual fuel from the fuel tank if storing for several months.

– 5 –

5. HEALTH AND SAFETY INFORMATION

5.1 GENERAL HEATER SAFETY WARNINGS

WARNING: Read all safety warnings and all instructions. Failure to follow the warnings

and instructions may result in electric shock, fire and/or serious injury. Save all warnings and

instructions for future reference.

1. Work area safety

− Keep work area clean and well lit. Cluttered or dark areas invite accidents.

− Do not operate heaters in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust. Heaters create sparks which may ignite the dust or fumes.

− Keep children and bystanders away while operating a heater. Distractions can cause you to
lose control.

2. Electrical safety

− Heaters plugs must match the outlet. Never modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) heaters. Unmodified plugs and matching outlets will
reduce risk of electric shock.

− Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

− Do not expose heaters to rain or wet conditions. Water entering a heater will increase the risk
of electric shock.

− Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the heater. Keep
cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase
the risk of electric shock.

− When operating a heater outdoors, use an extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric shock.

− If operating a heater in a damp location is unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of electric shock.

3. Personal safety

− Stay alert, watch what you are doing and use common sense when operating a heater.
Do not use a heater while you are tired or under the influence of drugs, alcohol or medication.
A moment of inattention while operating heaters may result in serious personal injury.

− Use personal protective equipment. Always wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries.

− Prevent unintentional starting. Ensure the switch is in the off position before connecting to
power source.

− Remove any adjusting key or wrench before turning the heater on. A wrench or a key left
attached to a rotating part of the heater may result in personal injury.

− Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery or long hair can get sucked into the in
moving parts of the heater.

4. Heater use and care

DO NOT move the heater when it is in operation or when plugged into the mains supply.

Only move heater once it has cooled and it has been unplugged.

− Use the correct heater for your application. The correct heater will do the job better and safer at
the rate for which it was designed.

− Do not use the heater if the switch does not turn it on and off. Any heater that cannot be
controlled with the switch is dangerous and must be repaired.

− Disconnect the plug from the power source before making any adjustments. Such preventive

– 6 –

5. HEALTH AND SAFETY INFORMATION

safety measures reduce the risk of starting the heater accidentally.

− Store idle heater out of the reach of children and do not allow persons unfamiliar with the
heater or these instructions to operate the power tool. Heaters are dangerous in the hands of
untrained users.

− Maintain heaters. Check for misalignment or binding of moving parts, breakage of parts and
any other condition that may affect the heaters operation. If damaged, have the heater repaired
before use. Many accidents are caused by poorly maintained heaters.

− Use the heater, in accordance with these instructions, taking into account the working
conditions and the work to be performed. Use of the heater for operations different from those
intended could result in a hazardous situation.

5. Service

− Have your heater serviced by a qualified repair person using only identical replacement parts.
This will ensure that the safety of the heater is maintained.

WARNING: Diesel fuel is carcinogenic. Take care when transporting, refuelling and storage of

diesel fuel. Always clean up fuel spills with regard to local legislative requirements.

WARNING: Before using this heater please read this OPERATING INSTRUCTION very

carefully. This USER’S MANUAL has been designed to instruct you as to the proper manner in
which to assemble, maintain, store, and most importantly, how to operate the heater in a safe
and efficient manner.

DANGER: Improper use of this heater can result in serious injury or death from burns, fire,

explosion, electrical shock, and/or carbon monoxide poisoning.

WARNING: Risk of Burns/Fire/Explosion!

− NEVER use fuels such as petrol, benzene, paint thinners, or other oil compounds in this heater
(RISK OF FIRE OR EXPLOSION)

− NEVER use this heater where flammable vapours may be present

− NEVER refill the heater’s fuel tank while heater is operating or still hot. This heater is
EXTREMELY HOT while in operation

− Keep all combustible materials away from this heater.

Use only diesel or kerosene fuel according to EN 267. For details please refer to your fuel supplier
or contact your dealer.

WARNING: Never leave the heater unattended while burning!
WARNING: Risk of Indoor Air Pollution!

− Use this heater only in well ventilated areas!

− Provide at least a three square foot (2,800 sq cm) opening of outside air for every
25,000Kcal/hr of heater rating.

− People with breathing problems should consult a physician before using the heater.

− Carbon Monoxide Poisoning: Early signs of carbon monoxide poisoning resemble flu-like
symptoms such as headaches, dizziness, and/or nausea. If you have these symptoms, your
heater may not be working properly.

− Get fresh air at once! Have the heater serviced. Some people are more affected by carbon
monoxide than others. These include pregnant women, those with heart or lung problems,
anaemia, or those under the influence of alcohol, or at high altitudes.

− Never use this heater in living or sleeping areas.

– 7 –

5. HEALTH AND SAFETY INFORMATION

WARNING: Risk of Electric Shock!

− Use only the electrical power (voltage and frequency) specified on the model plate of the
heater. Use only a three-prong, grounded outlet and extension cord.

− ALWAYS install the heater so that it is not directly exposed to water spray, rain, dripping water,
or wind.

− ALWAYS unplug the heater when not in use.

Minimum Clearances
Outlet: 8 feet (250cm).
Sides, Top and Rear: 4 feet (125cm).

− NEVER block air inlet (rear) or air outlet (front) of heater.

− NEVER use duct work in front or at rear of.

− NEVER move or handle heater while still hot.

− NEVER transport heater with fuel in its tank.

− DO NOT use with any form of external thermostat or remote starting device.

− ALWAYS locate heater on a stable and level surface.

− ALWAYS keep children and animals away from heater.

− Use 1-K kerosene in this heater. #1 fuel oil is a suitable substitute.

− Bulk fuel storage should be a minimum of 25ft from heaters, torches, portable generators,
or other sources of ignition. All fuel storage should be in accordance with National, state, or
local authorities.

– 8 –

5. HEALTH AND SAFETY INFORMATION

5.2 CONNECTION TO THE POWER SUPPLY

CAUTION: Risk of electric shock. Do not open.

This appliance is supplied with an approved plug and cable for your safety. The value of the fuse
fitted is marked on the pin face of the plug. Should the fuse need replacing, ensure the substitute
is of the correct rating, approved to BS1362 and ASTA or BS Kite marked.

ASTA
BSI
The fuse cover is removable with a small plain slot screwdriver. Ensure the fuse cover is replaced

before attempting to connect the plug to an electrical outlet. If the cover is missing, a replacement
must be obtained or the plug replaced with a suitable type.

If a replacement plug is to be fitted this must be carried out by a qualified electrician.
The damaged or incomplete plug, when cut from the cable shall be disabled to prevent connection

to a live electrical outlet.
This appliance is Class I† and is designed for connection to a power supply matching that detailed

on the rating label and compatible with the plug fitted.
If an extension lead is required, use an approved and compatible lead rated for this appliance.

Follow all the instruction supplied with the extension lead.

†

Earthed : This product requires an earth connection to protect against electric shock from

accessible conductive parts in the event of a failure of the basic insulation.

– 9 –

6. TECHNICAL DESCRIPTION

6.1 IDENTIFICATION

04174

(1)

(2)

(3)

(10)

(9)

(8)

(7)

(6)

(1) Upper shell.
(2) Hot air outlet.
(3) Fuel gauge.
(4) Fuel cap.
(5) Lamp.
(6) Fuel tank.
(7) ON/OFF switch.
(8) Pressure gauge.
(9) Fan guard.
(10) Handle.

04175

04176

(1)

(2)

(3)

(4)

(5)

(1)

(2)

(3)

(4)

(5)

(4)

(6)

(6)

(5)

(10)

(9)
(8)

(7)

(12)

(11)

(10)

(9)
(8)

(7)

(1) Upper shell.
(2) Hot air outlet.
(3) Fuel gauge.
(4) Fuel cap.
(5) Wheel.
(6) Lamp.
(7) Wheel support frame.
(8) Fuel tank.
(9) ON/OFF switch.
(10) Handle.

(1) Upper shell.
(2) Hot air outlet.
(3) Fuel gauge.
(4) Fuel cap.
(5) Wheel.
(6) Lamp.
(7) Wheel support frame.
(8) Fuel tank.
(9) ON/OFF switch.
(10) Pressure gauge.
(11) Fan guard.
(12) Handle.

– 10 –

7. UNPACKING & CHECKING

7.1 PACKAGING

Carefully remove the product from the packaging and examine it for any sign of damage that
may have happened during shipping. Lay the contents out and check them against the parts list
provided. If any part is damaged or missing; please contact the Draper Helpline (the telephone
number appears on the Title page) and do not attempt to use the product.

The packaging material should be retained at least during the guarantee period: in case the heater
needs to be returned for repair.

Warning! Some of the packaging materials used may be harmful to children. Do not leave any of
these materials in the reach of children.

If any of the packaging is to be thrown away, make sure they are disposed of correctly; according
to local regulations.

– 11 –

8. ASSEMBLING THE HEATER

8.1 HANDLE (04174) – FIG.1

− Align the holes in the upper housing with the
two holes in the handle.

− Insert and tighten screws securely with
screw driver.

8.2 WHEEL AND HANDLE (04175 &

04176) – FIG.2

− Slide axle (6) through wheel support frame
(8). Install wheel spacers (5) if provided.

Install wheels (4) on axle (6).

− IMPORTANT: When installing wheels (4),
point extended hub of wheels toward wheel
support frame (8). Secure wheels onto axle
using split pins.

− Place cap nuts (7) on axle ends. Gently tap
with hammer to secure.

− Place heater on wheel support frame (8).
Line up holes on fuel tank flange with holes
on wheel support frame (8).

− Place handle(s) on top of fuel tank flange.
Insert screws (1) through handle(s) (9), fuel
tank flange, and wheel support frame (8).
Attach nut finger tight after each screw
is inserted.

− After all screws are inserted, tighten nuts firmly.

FIG.

(1)

(2)

FIG.

1

(3)

2

(4)

(5)

(9)

(8)

(6) (7)

– 12 –

9. OPERATING THE HEATER

9.1 STARTING HEATER – FIG.3

− Follow all ventilation and safety information.

− Locate heater to provide maximum circulation
of the heated air. Follow all location
requirements noted in Safety Information on
page 6.

− Fill fuel tank with #1#2 diesel/fuel oil until fuel
gauge points to “F”.

− Attach fuel cap.

− Power supply. If using an extension cord, it
MUST be suitable for the heater. Check with
extension cord manufacturer if in doubt to
confirm application.

− For heater with ON/OFF (1) switch, push
switch to ON(|) position and heater should start
in 5 seconds.

NOTE: If the heater still does not start, push Power
Switch to “OFF”, then back to “ON”. If heater still
does not fire, see Troubleshooting Guide

NOTE: The electrical components of this heater
are protected by a fuse mounted in the PC board.
If the heater fails to fire, check this fuse first, and
replace if necessary. Also check the power source
to be sure that the proper voltage is being provided
to the heater.

9.2 TO STOP HEATER – FIG.3

Simply turn the Power switch to “OFF” position and
unplug the Power Cord.

9.3 TO RESTART THE HEATER

− Wait ten seconds after shutting off heater.

− Turn the Power Switch to “ON” position.

− Be sure to follow all starting procedure
precautions.

(1)

3 FIG.

– 13 –

10. STORING & TRANSPORTING THE HEATER

10.1 STORING & TRANSPORTING THE
HEATER – FIG.4

If shipping, transport companies require fuel tanks
to be empty.

− Drain fuel tank. Note: Drain plug on underside
of fuel tank. Remove drain plug to drain all fuel.

− Replace drain plug (1).

− If any debris is noted in old fuel, add 1 or 2
quarts of clean kerosene to tank, stir, and drain
again. This will prevent excess debris from
clogging filters during future use.

− Replace fuel cap or drain plug (1). Properly
dispose of old and dirty fuel. Check with local
automotive service stations that recycle oil.

− If storing, store heater in dry place. Make
sure storage place is free of dust and
corrosive fumes.

IMPORTANT: Do not store kerosene over summer
months for use during next heating season. Using
old fuel could damage heater.

(1)

4 FIG.

– 14 –

– 14 –

11. MAINTENANCE

Use only original equipment replacement parts.
The use of alternate or third party components
can cause unsafe operating conditions, and will
void your warranty. We suggest following a
maintenance schedule as follows.

WARNING: ENSURE HEATER HAS FULLY
COOLED AND DISCONNECT FROM POWER
SUPPLY BEFORE CONDUCTING ANY
MAINTENANCE.

11.1 FUEL/FUEL TANK

− Flush every 200 hours of operation or as
needed. Do not use water to flush the tank.
Use fresh Diesel or Kerosene ONLY.

11.2 AIR FILTERS – FIG.5

− The Air Intake Filter (3) should be replaced
or washed with soap and water and dried
thoroughly every 500 hours of operation,
or less, depending on conditions.

− The Output (2) and Lint (1) Filters should be
replaced every 500 hours of operation or less,
depending on conditions.

NOTE: Use of diesel may require additional
maintenance.

11.3 FAN BLADES – FIG.6

− Blades should be cleaned at least once per
heating season, depending on conditions.

− Remove all accumulated dust and dirt with a
damp cloth, taking care not to bend any of the
fan blades.

− Be sure fan blades are dry before re-starting
the heater.

11.4 NOZZLES – FIGS.7–8

− Nozzles should be cleaned or replaced at least
once per heating season. Contaminated fuel
could make this necessary immediately.

− To clean dirt from nozzle, blow compressed air
through nozzle front. It may be necessary to
soak nozzle in clean Diesel or Kerosene ONLY
to help loosen any particles.

NOTE: Use of diesel may require additional
maintenance. Using this heater without proper
maintenance or with contaminated or old fuel
may lead to improper combustion and possible
soot production. BE SURE FUEL USED
IS APPROVED.

FIG.

FIG.

FIG.

(1)

(2)

(3)

5

6

7

– 15 –

– 15 –

FIG.

8

11. MAINTENANCE

11.5 SPARK PLUG – FIG.9

− Clean and re-gap every 600 hours of operation,
or replace as needed. After removing the Spark
Plug (2), clean the terminals with a wire brush.
Re-gap (1) the terminals to 3.5mm.

11.6 PHOTOCELL – FIGS.10–11

− The Photocell (1) should be cleaned at least
once per heating season or more depending
on conditions. Use a cotton swap dipped in
water or alcohol to clean the lens (2) of
the Photocell.

− Reposition the photocell correctly – Fig.11.

(3) Photocell bracket.
(4) Photocell.
(5) PC board.

11.7 FUEL FILTER – FIG.12

− The Fuel Filter should be cleaned at least twice
per heating season by rinsing it in clean Diesel
or Kerosene.

− Contaminated fuel could make this necessary
immediately

− 1. Remove side cover screws using nut-driver.

− 2. Remove side cover (2).

− 3. Pull upper fuel line off fuel filter neck

− 4. Carefully pry bushing, fuel filter (1), and

lower fuel line out of fuel tank

− 5. Wash fuel filter with clean fuel and replace

in tank.

− 6. Attach upper fuel line to fuel filter neck.

− 7. Replace side cover.

FIG.

FIG.

9

10

(1)

(2)

(1)

(2)

(3)

(4)

– 16 –

– 16 –

FIG.

FIG.

(5)

11

(1)

(2)

12

11. MAINTENANCE

11.8 PUMP ROTOR – FIGS.13–14

− (Procedure if Rotor is Binding)

− 1. Remove upper shell

− 2. Remove filter end cover screws using

nut driver

− 3. Remove filter end cover and air filters.

− 4. Remove pump plate screws using nut-driver.

− 5. Remove pump plate.

− 6. Remove rotor (2), insert (1), and blades (3).

− 7. Check for debris in pump. If debris is found,

blow out with compressed air.

− 8. Install insert (1) and rotor.

− 9. Check gap on rotor (FIG.14). Adjust to

0.08/0.12mm if needed using gap adjust
screw (4). Note: Rotate rotor (2) one full
turn to ensure the gap is 0.08/0.12mm at
tightest position. Adjust if needed.

− 10. Install blades (3), pump plate, air filters,

and filter end cover.

− 11. Replace fan guard and upper shell

− 12. Adjust pump pressure. Note: If rotor is still

binding, proceed as follows.

− 13. Perform steps 1 through 6.

− 14. Place fine grade sandpaper on flat surface.

Sand rotor lightly in “figure 8” motion four
times

− 15. Reinstall insert (1) and rotor (2).

− 16. Perform steps 10 through 12.

11.9 PUMP PRESSURE ADJUSTMENT
– FIG.15

− While heater is operating, turn relief valve
clockwise to increase, counter-clockwise to
decrease Use flat blade screwdriver to turn
valve. Correct pump pressure is as follows:

Stock number Pump Pressure (bar)

04174 0.33

04175 0.35

04176 0.37

Tolerance ± 10%

FIG.

FIG.

(1)

(2)

(3)

13

(4)

(2)

14

15 FIG.

− For best measurement of pressure, test with full
tank of fuel. Optimum pressure occurs when

the nose cone is cherry red and there are no
extending flames from the heater.

– 17 –

– 17 –

11. MAINTENANCE

11.10

WIRING DIAGRAM – FIG.16

– 18 –

12. TROUBLESHOOTING

12.1 TROUBLESHOOTING GUIDE

Problem Possible Cause Solution

1. Incorrect pump pressure. 1. Adjust Pump Pressure
(page 17).

Heater fires, but Main PCB
shuts heater off after a short
period of time. Lamp is
flickering.

Heater will not operate, or
motor runs for short time.
Lamp flickers.

2. Dirty Input, Output or

Lint Filter.

3. Dirty Fuel Filter . 3. Clean/replace Fuel Filter

4. Nozzle is Dirty. 4. Clean/replace Nozzle

5. Photocell lens is Dirty. 5. Clean/replace Photocell

6. Photocell not installed

properly.

7. Photocell Defective. 7. Replace Photocell

8. Improper electrical

connection between
Main PCB and Photocell.

1. No fuel in fuel tank. 1. Fill tank with fresh

2. Incorrect pump pressure. 2. Adjust Pump Pressure

3. Corroded Spark Plug or

incorrect plug gap.

4. Dirty Fuel Filter. 4. Clean/replace Fuel Filter

5. Dirty Nozzle. 5. Clean/replace Nozzle

6. Moisture in Fuel/Fuel Tank. 6. Rinse out fuel tank with

7. Improper electrical

connection between
Transformer and Circuit
Board.

8. Ignitor Wire not connected

to Spark Plug.

9. Defective Ignitor. 9. Replace Ignitor.

2. Clean/replace Air Filter
(page 15).

(page 16).

(page 15).

(page 16).

6. Adjust Photocell position
(page 16).

(page 16).

8. Check wiring connections
(page 18).

kerosene.

(page 17).

3. Clean/replace Spark Plug
(page 16).

(page 16).

(page 15).

clean fresh kerosene.

7. Inspect all electrical
connections. See Wiring
Diagrams (page 18).

8. Re-attach Ignitor wire to
Spark Plug (page 16).

– 19 –

12. TROUBLESHOOTING

Fan does not operate when
heater is plugged in and
Power Switch is in the “ON”
position. The lamp is
flickering.

Poor Combustion and / or
excess soot production.

Heater does not turn on.

1. Broken electrical
connection between
Main PCB and motor.

2. Temperature limit has
overheated.

3. To stop heater operation
mistake or electrical
power stop.

1. Dirty Input, Output or Lint
Filter.

2. Dirty Fuel Filter. 2. Clean/replace Fuel Filter

3. Poor quality of fuel. 3. Be sure fuel is not

4. PSI is too high or too low. 4. Use proper pressure

1. No electrical power. 1 Check power cord and

2. Fuse Blown. 2. Check/replace Fuse.

3. Improper electrical
connection between
Temperature Limit Sensor
and Circuit Board.

1. Inspect all electrical
connections. See Wiring
Diagrams (page 18).

2.1 Push Power Switch to
“OFF” and allow heater
to cool for 10 minutes.
Push Power Switch to
back to “ON”.

2.2 Clean/replace Fan
(page 15).

3. Push Power Switch to
“OFF” and allow heater
to cool for 10 minutes.
Push Power Switch to
back to “ON”.

1. Clean/replace Air Filter
(page 15).

(page 16).

contaminated or old.

(page 17).

extension cord to insure
of proper connection.
Test power supply.

3. Inspect all electrical
connections. Wiring
Diagrams (page 18).

– 20 –

13. DISPOSAL

13.1 DISPOSAL

– At the end of the machine’s working life, or when it can no longer be repaired, ensure that it is

disposed of according to national regulations.
– Contact your local authority for details of collection schemes in your area.
In all circumstances:

• Do not dispose of power tools with domestic waste.

• Do not incinerate.

• Do not dispose of WEEE* as unsorted municipal waste.

* Waste Electrical & Electronic Equipment.

– 21 –

– 22 –

– 23 –

CONTACTS

Draper Tools Limited

UK: Hursley Road, Chandler’s Ford, Eastleigh,

Hampshire. SO53 1YF. U.K.

EU: Oude Graaf 8

6002 NL Weert (NL)

Help Line: [phone]

Sales Desk: [phone]

Internet: drapertools.com

E-mail: [e-mail]

General Enquiries: [phone]

Service/Warranty Repair Agent:

For aftersales servicing or warranty repairs, please contact the

Draper Tools Help Line for details of an agent in your local area.

YOUR DRAPER STOCKIST

PJPR0621

©Published by Draper Tools Limited.

No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means,
electronic, mechanical photocopying, recording or otherwise without prior permission in writing from Draper Tools Ltd.