Draper WL6B, WL6W Instructions For Use Manual

■ STOCK No.61676 ■ PART No.WL6B

61677 WL6W

•INSTRUCTIONS•

04/2000

IMPORTANT: PLEASE READ THESE INSTRUCTIONS

CAREFULLY TO ENSURE THE SAFE AND EFFECTIVE USE OF THIS LIGHT UNIT

WALL/CEILING LIGHT

SPECIFICATION

INSTRUCTIONS

Whilst every effort has been made to ensure that the accuracy of information given in this booklet
is correct at time of going to print, the Draper Tools policy of continuous improvement determines
the right to change specification without notice.

Voltage....................................................................................................................230V A.C. /50Hz.

Maximum load rating..................................................................................................................60W

Size ......................................................................................................................260mmØ x 150mm

CAUTION: We recommend this lamp is installed by a qualified electrician. Switch off main power
supply before installation. Please read and understand these instructions before installation.
Keep them for future reference. IF IN DOUBT CONSULT A QUALIFIED ELECTRICIAN. This product
should not be tampered with or modified in any circumstances, if this does occur the product may
become unsafe and the warranty will be invalid.This product is suitable for outdoor use.

SAFETY

Please make sure that the mains electricity is isolated (switched off) before you start the
installation or undertake any maintainence. It is recommended that the circuit fuse is removed to
prevent the electricity being accidentally switched on. This product contains glass, please take
care when handling and fitting.

- 1 -

INSTRUCTIONS Cont.

FIXING INSTRUCTIONS

1. Unscrew the four screws located on the front of
the lamp and remove the front cover and glass.

2. Slide bulb holder and plate upwards. Carefully
open the light to access mounting holes and
terminal block. FIG.1.

3.Place light against the wall and mark the position
of the fixing holes (1) as shown in the diagram.
FIG.2. Split the centre of the grommet to allow
cable access as shown at position (2) in the
diagram.

4. Drill the holes with a suitable drill bit and plug
the mounting holes. Ensure there are no power
cables or pipes below the surface before
commencing drilling.

5. Feed the mains power cable through the grommet
(2). Now attach the backing plate to the wall
using the two screws supplied. Do not
overtighten the screws as this could damage the
base.

6. Connection to the mains power should be made
using the general wiring code shown in FIG.3.
THIS PRODUCT MUST BE EARTHED.

NOTE: make sure that the incoming mains cable
corresponds to the correctly coloured internal wire
from the unit.

7. The incoming Brown/Red live wire must be
opposite the Black live wire from the unit, the
Neutral Blue must be opposite the Blue Neutral
wire from the unit. The Green and Yellow earth
wire must be opposite the Green and Yellow
earth wire from the unit.

8 . The terminal block may be removed for ease of

connection. Tighten all terminal screws and
make sure that there are no loose strands of cable
showing. Be sure to replace the terminal block on
its fixings.

1. Terminal position for Earth (from
house mains Yellow and Green/Green.

2. Terminal position for Neutral (from
house mains Blue/Black).

3. Terminal position for Live (from house
mains Brown/Red)

FUSE VALUE

The light should be connected to a 5 amp circuit. If the existing fuse in the circuit is higher than
5 amps an inline fuse of 3 amps should be fitted. This light should only be connected to a
220/240V-50Hz electricity supply in accordance with I.E.E. wiring safety regulations.

Bulb
holder.

Plate cover.

1. Slide up to
remove

2. Slide

down to

replace.

FIG.1.

E

N

L

FIG.2.

2. Split
grommet
for cable

access.

1. Fixing
holes, mark wall
before drilling.

Internal view of

backplate.

FIG.3.

EARTH

NEUTRAL

LIVE

To Earth

To bulb holder

To bulb holder

- 2 -

(1)

(2)

(3)

INSTRUCTIONS Cont.

9. Insert a bulb up to a maximum of 60W screw-in Edison screw bulb into the holder. Slide bulb
holder and plate back into place and replace the glass and the front cover. Replace the four
screws from the front and secure - DO NOT overtighten.

10. Restore mains electricity supply.

IMPORTANT: IF IN ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.

GUARANTEE

Draper electric lights have been carefully tested and inspected before shipment and are
guaranteed to be free from defective materials and workmanship for a period of 12 months from
the date of purchase except where items are hired out when the guarantee period is ninety days
from the date of purchase.

Should the light develop any fault, please return the complete item to your nearest authorized
warranty repair agent or contact Draper Tools Limited, Chandlers Ford, Eastleigh, Hampshire.
SO53 1YF. England. Telephone: [phone].

If upon inspection it is found that the fault occurring is due to defective materials or workmanship,
repairs will be carried out free of charge. This guarantee does not apply to normal wear and tear,
nor does it cover any damage caused by misuse, careless or unsafe handling, alterations,
accident, or repairs attempted or made by any personnel other than the authorized Draper
warranty repair agent.

This guarantee applies in lieu of any other guarantee expressed or implied and variations of its
terms are not authorized.

Your Draper guarantee is not effective unless you can produce upon request a dated receipt or
invoice to verify your proof of purchase within the 12 month period.

Please note that this guarantee is an additional benefit and does not effect your statutory rights.

Bulbs are a consumable and are not covered by this guarantee.

DRAPER TOOLS LIMITED.

- 3 -

NOTES

- 4 -

NOTES

- 5 -

NOTES

- 6 -

DRAPER TOOLS LIMITED,

Hursley Road, Chandler's Ford,

Eastleigh, Hants. SO53 1YF. England.

Tel: [phone].

Fax: [phone].

©Published by Draper Tools Ltd.

No part of this publication may be reproduced,

stored in a retrieval system or transmitted in

any form or by any means, electronic, mechanical

photocopying, recording or otherwise without prior

permission in writing from Draper Tools Ltd.

YOUR DRAPER STOCKIST

www.draper.co.uk
e-mail: [e-mail]