Page 1
■ STOCK No.57675 ■ PART No.RFL610
•INSTRUCTIONS•
06/99
IMPORTANT: PLEASE READ THESE INSTRUCTIONS
CAREFULLY TO ENSURE THE SAFE AND EFFECTIVE USE OF THIS LIGHT
RECHARGEABLE FLUORESCENT
LIGHT
Page 2
DECLARATION OF CONFORMITY
SPECIFICATION
OPERATION
We
Draper Tools Ltd. Hursley Road, Chandlers Ford, Eastleigh, Hampshire. SO53 1YF. England.
Declare under our sole responsibility that the product:
Stock No:-57675 Part No:-RFL610
Description:- Rechargeable fluorescent light.
To which this declaration relates is in conformity with the following directive(s):- 73/23/EEC &
89/336/EEC.
With reference to:- BS EN 60335-2-29:1991, BS 3456:Part 201:1990, EN 55015:1996,
EN61000-3-2:1995, EN 61000-3-3:1995 & EN 61547:1995.
JOHN DRAPER
Managing Director 06/99
Whilst every effort has been made to ensure accuracy of information given in this booklet is
correct at time of going to print , the Draper Tools policy of continuous improvement determines
the right to change specification without notice.
Average charging time..................................................................................................18 - 20 hours
Average usage time for one tube ......................................................................................4 - 5 hours
Average usage time for two tubes ....................................................................................2 - 3 hours
Battery type................................................................................................6V/6AH sealed lead acid
Tube type ................................................................................................................2 x 18W-600mm
Input voltage ..................................................................................................................12V/400mA
Charge power supply ..................................................................................A.C. 220-240V/50-60Hz.
1. Before using the light for the first time, ensure it is fully charged and the switch on the back
panel is ‘ON’.
2. Turn light on by simply sliding the switch located on the front of the light to the top position (left
tube), second position (right tube) or lowest position (two tubes).
Page 3
CHARGING
GUARANTEE
Draper electric lights have been carefully tested and inspected before shipment and are
guaranteed to be free from defective materials and workmanship for a period of 12 months from
the date of purchase except where tools are hired out when the guarantee period is reduced to
ninety days from the date of purchase.
Should the light develop any fault, please return the complete item to your nearest authorized
warranty repair agent or contact Draper Tools Limited, Chandlers Ford, Eastleigh, Hampshire.
SO53 1YF. England. Telephone: (01703) 266355.
If upon inspection it is found that the fault occurring is due to defective materials or workmanship,
repairs will be carried out free of charge. This guarantee does not apply to normal wear and tear,
nor does it cover any damage caused by misuse, careless or unsafe handling, alterations,
accident, or repairs attempted or made by any personnel other than the authorized Draper
warranty repair agent.
This guarantee applies in lieu of any other guarantee expressed or implied and variations of its
terms are not authorized.
Your Draper guarantee is not effective unless you can produce upon request a dated receipt or
invoice to verify your proof of purchase within the 12 month period.
Please note that this guarantee is an additional benefit and does not effect your statutory rights.
Fluorescent tubes are a consumable and are not covered by this guarantee.
DRAPER TOOLS LIMITED.
1. To charge light, insert plug on the end of mains charger lead into socket located on side of
light. Plug mains adaptor charger into 220-240V mains supply socket and switch on power
supply. A red light on front of unit should light.
2. For emergency function in the event of a power failure, if switch is at the ‘ON’ position during
charging procedure the light will automatically illuminate to provide emergency lighting and
return to charge when A/C current is restored.
3. Night light illuminator will be visible when light is stored/charged in a dark environment.
REPLACING TUBES
1. Ensure that the power supply is disconnected and the light switch is in ‘OFF’ position.
2. Unscrew the lens cover(s), tilt the lens, and slide off.
3. Rotate tube(s) until prongs align with gap in contact covers. Lift tube(s) and fit replacement(s).
Replacement tubes are available – quote Stock No. 57793, Part No.YRFL 610.
4. Replace lens cover(s).
MAINTENANCE
1.When light goes off suddenly during use, recharge immediately.
2.You should leave light on charge whenever it is not in use.
3. Always recharge after use, if not on constant charge you should recharge especially when not
used for over three months or longer.
4. Do not drop. Store securely when transporting.
5. Ensure light is secure and stable when wall mounted or using folding stand/hanging hook.
Page 4
DRAPER TOOLS LIMITED,
Hursley Road, Chandler's Ford,
Eastleigh, Hants. SO53 1YF. England.
Tel: (01703) 266355.
Fax: (01703) 260784.
©Published by Draper Tools Ltd.
No part of this publication may be reproduced,
stored in a retrieval system or transmitted in
any form or by any means, electronic, mechanical
photocopying, recording or otherwise without prior
permission in writing from Draper Tools Ltd.
YOUR DRAPER STOCKIST
Loading...