Draper REMOTE STARTER, 67794, RS1 Instructions Manual

REMOTE STARTER

■ STOCK No.67794 ■ PART No.RS1

• INSTRUCTIONS •

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE

SAFE AND EFFECTIVE USE OF THIS TOOL.

GENERAL INFORMATION

This manual has been compiled by Draper Tools and is an integrated part of the power tool equipment, which
should be kept with the machine.

This manual describes the purpose for which this tool has been designed and contains all the necessary
information to ensure its correct and safe use.We recommend that this manual is read before any operation of
the machine, before performing any kind of adjustment to the machine, and prior to any maintenance tasks. By
following all the general safety instructions contained in this manual, it will ensure both machine and operator
safety, together with longer life of the tool itself.

All photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the
machine.

Whilst every effort has been made to ensure accuracy of information contained in this manual, the Draper Tool
policy of continuous improvement determines the right to make modifications without prior warning.

10/2001

- 1 -

The Draper Tools policy of continuous improvement determines the right to change specification
without notice.

Part No. ......................................................................................................................RS1

Stock No...................................................................................................................67794

Application:

Suitable for all types of vehicles fitted with a starter motor (including diesels)
running on 6, 12 and 24V systems.
Using this switch avoids having an assistant to crank the engine while carrying
out the following engine tuning tests:

• Setting the dwell angle.

• Setting tappets and valves.

• Compression testing.

• Fuel pump and fuel pressure testing.

• Checking the starter motor.

• Checking the alternator etc.

Warning: When working on vehicles fitted with automatic gear box ensure the

gearbox is in the park position.

SPECIFICATION

REMOTE
STARTER

- 2 -

OPERATION & USE

CONNECTION INSTRUCTIONS:

NOTE: Prior to connection ensure the parking
brake is applied and the vehicle is not in gear.
It is also good practice to secure the vehicle
with wheel chocks (Draper stock no.54500).
For vehicles fitted with an (older type) inertia
starter motor see Fig. 1. The solenoid can be
located on the inner wing or bulk head for the
majority of older vehicles. Refer to the vehicle
manufacturers handbook or Haynes manual.
Remove the wire on the solenoid from the
ignition switch and attach one clip of the
remote stater to the terminal. Attach the other
clip on to the large solenoid wire which comes
from the battery positive terminal. Do not
connect across any of the other terminals as
this will result in damage to the vehicle or the
remote starter. For vehicles fitted with a (newer
type) pre-engaged starter motor see Fig. 2.
This type has the solenoid mounted on the
starter motor body. Remove the thin wire on
the back of the solenoid and attach one clip
from the remote starter. Connect the other clip
directly to the battery positive terminal.
NOTE: Some vehicles have the battery located
in the boot or under the back seat. In this case
refer to the vehicle manufacturers handbook or
Haynes manual to find details and location of
the remote positive terminal under the bonnet.

CRANKING:

Disable the ignition system to prevent the
engine firing. For this procedure refer to the
vehicle manufacturers handbook or Haynes
manual for details. Switch on the ignition
switch and press the trigger on the remote
start in small bursts.

STARTING:

Switch on the ignition switch and press the
trigger on the remote start until the engine
fires. Do not press the trigger while the engine
is running. To stop the engine, turn the ignition
switch to the ‘off’ position.

NOTE: If there is no response, recheck the
connections. If the engine cranks but does not
fire, stop. Cranking the starter motor for long

Fig.1.

periods (more than a few seconds) can
damage the starter motor.

NOTE: After all test are complete double check
on the vehicle all connections have been
reinstated correctly before starting the engine.

Any problems contact the Draper help line on [phone].

Fig.2.

REMOTE
STARTER

SOLENOID

STARTER

MOTOR

BATTERY

COIL

Ignition switch
connection
wire (THIN)

Ignition switch
connection
wire (THIN)

BATTERY

STARTER

MOTOR

DRAPER TOOLS LIMITED,

Hursley Road, Chandler's Ford, Eastleigh, Hants. SO53 1YF. U.K.

Helpline: [phone].

Sales Desk: [phone].

General Enquiries: [phone].

Fax: [phone].

http://www.draper.co.uk
e-mail: [e-mail]

©Published by Draper Tools Ltd.

No part of this publication may be reproduced,

stored in a retrieval system or transmitted in

any form or by any means, electronic, mechanical

photocopying, recording or otherwise without prior

permission in writing from Draper Tools Ltd.

YOUR DRAPER STOCKIST