APPLICATION GUIDE FOR:
ENGINE
TIMING KIT
19130
BRITISH
MADE
This document is part of the product, keep it for the life of the product passing it on to any subsequent holder of
the product. Read all information before operating product.
This guide has been compiled by Draper Tools describing the purpose for which the product has been designed,
and contains necessary information to ensure its correct and safe use. By following the information contained in
this guide, it will ensure both product and operator safety, together with longer life of the product itself.
AlI photographs and drawings in this guide are supplied by Draper Tools to help illustrate the operation of the
product.
Whilst every effort has been made to ensure the accuracy of information contained in this guide, the Draper
Tools policy of continuous improvement determines the right to make modifications without prior warning.
1. TITLE PAGE
1.1 INTRODUCTION:
USER GUIDE FOR: Engine Timing Kit
Stock No: 19130
Part No: ETK235
1.2 REVISIONS:
Date first published June 2018.
As our user manuals are continually updated, users should make sure that they use
the very latest version.
Downloads are available from: http://drapertools.com
Draper Tools Limited
Hursley Road
Chandler’s Ford
Eastleigh
Hampshire
SO53 1YF
UK
Website: drapertools.com
Product Helpline: +44 (0) 23 8049 4344
General Fax: +44 (0) 23 8026 0784
1.3 UNDERSTANDING THIS GUIDES SAFETY CONTENT:
WARNING! – Information that draws attention to the risk of injury or death.
CAUTION! – Information that draws attention to the risk of damage to the product or
surroundings.
1.4 COPYRIGHT © NOTICE:
Copyright © Draper Tools Limited.
Permission is granted to reproduce this publication for personal and educational use
only. Commercial copying, redistribution, hiring or lending is prohibited.
No part of this publication may be stored in a retrieval system or transmitted in any
other form or means without written permission from Draper Tools Limited.
In all cases this copyright notice must remain intact.
- 2 -
2. CONTENTS
1. TITLE PAGE
1.1 INTRODUCTION.......................................................................................................... 2
1.2 REVISION HISTORY .................................................................................................. 2
1.3 UNDERSTANDING THIS GUIDE ................................................................................. 2
1.4 COPYRIGHT NOTICE .................................................................................................2
2. CONTENTS
2.1 CONTENTS .................................................................................................................... 3
3. GUARANTEE
3.1 GUARANTEE ............................................................................................................... 4
4. GENERAL PRODUCT INFORMATION
4.1 GENERAL PRODUCT INFORMATION ....................................................................... 5
5. HEALTH AND SAFETY INFORMATION
5.1 GENERAL SAFETY INSTRUCTIONS FOR USE
Personal safety ........................................................................................................... 6
6. CONTENTS
6.1 PARTS DRAWING AND LISTING............................................................................... 7
7. APPLICATION
7.1 PRODUCT APPLICATION AND COMPATIBILITY LISTING ...................................... 8
8. PREPARATION
8.1 ADVISORIES BEFORE USE ...................................................................................... 9
9. PROCEDURE AND APPLICATION GUIDE
9.1 APPLICATION GUIDANCE ........................................................................................ 10
10. EXPLANATION OF SYMBOLS
10.1 EXPLANATION OF SYMBOLS .................................................................................. 11
- 3 -
3. GUARANTEE
3.1 GUARANTEE
Draper tools have been carefully tested and inspected before shipment and are guaranteed to be
free from defective materials and workmanship.
Should the tool develop a fault, please return the complete tool to your nearest distributor or
contact:
Draper Tools Limited, Chandler's Ford, Eastleigh, Hampshire, SO53 1YF. England.
Telephone Sales Desk: (023) 8049 4333 or:
Product Helpline (023) 8049 4344.
A proof of purchase must be provided.
If upon inspection it is found that the fault occurring is due to defective materials or workmanship,
repairs will be carried out free of charge. This guarantee period covering parts/labour is 12 months
from the date of purchase except where tools are hired out when the guarantee period is 90 days
from the date of purchase. This guarantee does not apply to normal wear and tear, nor does it
cover any damage caused by misuse, careless or unsafe handling, alterations, accidents, or
repairs attempted or made by any personnel other than the authorised Draper warranty repair
agent.
Note: If the tool is found not to be within the terms of warranty, repairs and carriage charges will be
quoted and made accordingly.
This guarantee applies in lieu of any other guarantee expressed or implied and variations of its
terms are not authorised.
Your Draper guarantee is not effective unless you can produce upon request a dated receipt or
invoice to verify your proof of purchase within the guarantee period.
Please note that this guarantee is an additional benefit and does not affect your statutory rights.
Draper Tools Limited.
- 4 -
4. GENERAL PRODUCT INFORMATION
This product is designed to be used correctly and with care for the purpose for which it is intended.
No liability is accepted by Draper Tools Limited for incorrect use or application of any of our
products, and Draper Tools Limited cannot be held responsible for any damage to personnel,
property or equipment when using this product. Incorrect use will also invalidate any warranty.
The applications database and any instructional information provided has been designed to offer
general guidance for a particular product’s use and while all attention is given to the accuracy of
the data, no project should be attempted without referring first to the manufacturer’s technical
documentation (workshop or instruction manual) or the use of a recognised authority such as
Autodata.
It is our policy to continually improve our products and thus we reserve the right to alter
specifications and components without prior notice. It is the responsibility of the user to ensure the
suitability of the product and information prior to use.
- 5 -
5. HEALTH AND SAFETY INFORMATION
GENERAL SAFETY INSTRUCTIONS
Warning: Please read all safety warnings and all details carefully. Failure to follow the warnings
may result in serious injury or major component damage.
Important: Draper Tools recommends that this product should not be modified or used for any
application other than that for which it was designed.
Save all warnings and instructions for future reference.
1) Personal safety
a) Stay alert, watch what you are doing and use common sense when using this product.
Do not use this product while you are tired or under the influence of drugs, alcohol or any
medication. A moment of inattention while using this product may result in serious personal
injury.
b) Use personal protective equipment as necessary.
c) Check and remove any part of the product before turning/testing the engine. A part left
attached to a rotating part of the engine may result in personal injury or major component
damage.
d) Carefully clean the tool components after every use.
f) Keep the tool components safe and tidy.
g) Do not use this product for any purpose other than for which it is designed.
Warning! Some of the packaging materials used may be harmful to children. Do not leave any of
these materials in the reach of children.
If any of the packaging is to be thrown away, make sure it is disposed of correctly; according to
local regulations.
- 6 -
6. CONTENTS
B
B
A
C
D
E
F
ITEM DESCRIPTION OEM STOCK No.
A 3mm Setting Pin T10115 35558
B Injection Pump Timing Pin 3359 35559
C Tension Tool T10008 35561
D Crankshaft Locking Tool T10050 35562
E Crankshaft Alignment Tool T10100 35563
F Tensioner Pin T10060 35564
- 7 -
7. APPLICATION
The 19130 has been developed as an engine timing kit for the vehicles listed below.
Comprehensive kit covering a wide range of the VAG group of vehicles. Enables the user to lock
the engine in the ‘timed’ position so the timing belt can be replaced. The kit comprises of camshaft
locking pins, fuel pump locking pin and crankshaft locking plates.
Used on the following Vehicles:
Audi A1 2010 - 2015
Audi A2 2000 - 2006
Audi A3 2001 - 2013
Audi A4 1999 - 2016
Audi A5 2008 - 2015
Audi A6 1998 - 2015
Audi Q3 2011 - 2015
Audi Q5 2008 - 2016
Audi TT 2008 - 2014
Seat Alhambra 1999 - 2015
Seat Altea 2004 - 2015
Seat Arosa 1999 - 2005
Seat Cordoba 2002 - 2009
Seat Exeo 2009 - 2013
Seat Ibiza 2000 - 2015
Seat Toledo 2000 - 2015
Skoda Fabia 2000 - 2006
Skoda Fabia 2005 - 2015
Skoda Octavia 2002 - 2013
Skoda Praktik 2007 - 2015
Skoda Rapid 2012 - 2015
Skoda Roomster 2006 - 2015
Skoda Superb 2002 - 2016
Skoda Yeti 2009 - 2016
Engine Codes:
1.2cc
ANY, CFWA, AYZ
1.4cc
AMF, ATL, BHC, BMS, BNM, BNV, BAY, BWB
1.6cc
CAYB, CAYC, CAYA, CLNA, CAYD, CAYE
1.9cc
ASZ, ATD, AXR, BLS, BKC, BXE, AJM, ATJ, AVB, AVF, AWX, BKE, BRB, ANU, AUY,
BTB, BVK, BJB, BLT, BMT, BPX, BUK, BXJ, ARL, BSW, BPZ, BSV, AVQ, BRU, BXF,
AXB, AXC, BRR, BRS, BSU, BRM
2.0cc
CFHB, CFHD, CBAA, CBAB, CFFA, CFFB, CBBB, CFGB, CLJA, AZV, BKD, BMM, BMN,
BUY, BLB, BNA, BPW, BRC, BRD, BRE, BRF, BVA, BVF, BVG, CAGA, CAGB, CAGC,
CAHA, CAHB, CGLC, CGLD, CJCA, CJCB, CJCC, CJCD, CMFA, CMFB, CMEA, CGLE,
CMGB, CFGC, CFGD, CLLB, CGLA, CGLB, CFFE, BRT, BVH, CEGA, CFHC, CFJA,
CLCB, CFHF, CLCA, BSS, BMP, CFHA, CBDB, CLLA, BGW, BHW, CBAC, CBDC, BKP,
BMA, BMR, BUZ, BVE, BWV, CBBA, CFFD, CFJB, CFCA, CAAA, CAAB, CAAC, CAAD,
CAAE, CCHA, CCHB, CDCA, CNEA, CSHA, CDBA, CNFA, CNFB, CFHE, BDJ, BST,
CKUB, CKTB, CKTC, CKUC, CSLB, CSNA, CBDA, BDK, CJAAA
Volkswagen Amarok 2010 - 2016
Volkswagen Beetle 2000 - 2015
Volkswagen Bora 1998 - 2005
Volkswagen Caddy 2003 - 2015
Volkswagen CC 2012 - 2017
Volkswagen Crafter 2011 - 2017
Volkswagen Eos 2006 - 2015
Volkswagen Fox 2005 - 2011
Volkswagen Golf 1998 - 2015
Volkswagen Jetta 2005 - 2016
Volkswagen Lupo 1999 - 2005
Volkswagen Lupo 2000 - 2005
Volkswagen Passat 1998 - 2015
Volkswagen Polo 1999 - 2014
Volkswagen Scirocco 2008 - 2014
Volkswagen Sharan 1999 - 2015
Volkswagen Tiguan 2007 - 2016
Volkswagen Touran 2003 - 2015
Volkswagen Transporter T5 2003 - 2015
- 8 -
8. PREPARATION
The following is for guidance only. Please refer to OEM derived data such as the vehicle
manufacturer’s own data or Autodata. The use of this product is purely down to the user’s
discretion and Draper Tools Limited cannot be held responsible for any damage caused what so
ever.
Preparation and precautions:
• Raise the front of the vehicle and remove the both front wheels and inner wheel arches where
required.
• It may be necessary to remove the front bumper dependent on the vehicles type.
• Remove the engine under shield, top cover and auxiliary drive belt(s).
• Ensure the engine is at TDC cylinder number 1.
• Support the engine with a suitable jack and remove the right hand engine mounting where
required for access.
• Turn the crankshaft in the normal direction of rotation until the camshaft marks are aligned.
- 9 -
9. PROCEDURE AND APPLICATION GUIDE
Depending on manufacture and model, some engine components do change. Please check with
Autodata or the manufacturer’s data before use.
Component 6
Tensioner locking pin for the Auxiliary belt tensioner.
Used to lock the tensioner for the auxiliary belt
tensioner to allow the auxiliary belt to be removed and
refitted with ease.
Component 2
Camshaft & Fuel Injection pump Locking Pins used to lock
the cam shaft in its times position fit as shown in figure 1
Component 4/5
Crankshaft locking tools used to lock the crankshaft in its
timed position fitted as shown in fig.1. 4 and 5 look similar
but are in fact quite different. The tool used depends on
the application engine number. To identify which tool to use
look at the positioning of the crankshaft timing mark on the
front pulley. Figure 2 use component 4 (T10050) for figure
3 use component 5 (T10100). Both tools will only fit by sliding
in to mesh with the crankshaft pulley from the front of the
engine. 4 and 5 will not fit if lowered into position.
Component 1
Back off the Belt tensioner to allow pin 1 to be fitted to lock the
tensioner in its retracted position as shown. See figure 4.
Component 3
Tensioner Locking Tool – where a hydraulic tensioner has been
used, use component 3 to lock it in its retracted position. See
figure 5.
FIG.3
FIG.1
FIG.2
FIG.4
FIG.5
Please note images are for guidance only and subject to change.
- 10 -
10. EXPLANATION OF SYMBOLS
10.1 EXPLANATION OF SYMBOLS
Read the guide.
Refer to website.
- 11 -
CONTACTS
Draper Tools Limited, Hursley Road,
Chandler's Ford, Eastleigh, Hampshire. SO53 1YF. U.K.
Helpline: (023) 8049 4344
Sales Desk: (023) 8049 4333
Internet: drapertools.com
E-mail: sales@drapertools.com
General Enquiries: (023) 8026 6355
Service/Warranty Repair Agent:
For aftersales servicing or warranty repairs, please contact the
Draper Tools Helpline for details of an agent in your local area.
YOUR DRAPER STOCKIST
CMDB0618
©Published by Draper Tools Limited.
No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means,
electronic, mechanical photocopying, recording or otherwise without prior permission in writing from Draper Tools Ltd.
Loading...