Page 1
GENERAL INFORMATION
This manual has been compiled by Draper Tools and is an integrated part of the product, which should be kept with the product.
This manual describes the purpose for which this product has been designed and contains all the necessary information to ensure its
correct and safe use.We recommend that this manual is read before any operation of the product,before performing any kind of
adjustment to the product, and prior to any maintenance tasks. By following all the general safety instructions contained in this manual, it
will ensure both product and operator safety, together with longer life of the product itself.
All photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product.
Whilst every effort has been made to ensure accuracy of information contained in this manual,the Draper Tool policy of continuous
improvement determines the right to make modifications without prior warning.
DOOR CLOSER
• INSTRUCTIONS •
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO
ENSURE THE SAFE AND EFFECTIVE USE OF THIS TOOL.
■ STOCK No.62894 ■ PART No.DC15/30
06/2000
Page 2
- 2 -
■STOCK No.62894 ■ PART No.DC15/30
OPENING TO 120°
■DIMENSION A = 95mm
OPENING FROM 120° TO 180°
■DIMENSION A = 65mm
INSTALLATION INSTRUCTIONS FOR
REGULAR ARM (PULL SIDE) MOUNTING
This installation process covers regular arm installations up to 180° openings.
1. Select the door opening angle and use the dimensions shown opposite. Mark four holes on the door
for the door closer and two holes on the frame for
the arm shoe.
2. Drill 4mmØ pilot holes in the door and frame for the
fixings supplied.
3. Fix the forearm/arm shoe assembly to the door
frame using the fixings supplied.
4. Attach the closer to the door using the fixings supplied.
Note: The speed adjusting valve must be positioned
towards the hinged edge of the door.
5. Install the main arm onto the top pinion shaft, perpendicular to the door as illustrated below. Tightly
secure it in place using the screw/washer assembly
supplied.
6. Adjust the length of the forearm so that it is perpendicular to the door frame when assembled to preloaded main arm (see ‘top view’ illustration below).
Secure the forearm to the main arm using the
screw/washer assembly provided.
7. Snap the pinion cap over the pinion shaft at the bottom of the closer unit.
8. Adjust the closing speed of the door using the procedure detailed on page 5.
REGULAR ARM INSTALLATION
Closer installs on PULL/HINGE side of door
Illustrated
Left Hand Door-LH or
Right Hand Reverse-RHR
TYPICAL TOP VIEW
INSTALLATION
Page 3
- 3 -
■STOCK No.62894 ■ PART No.DC15/30
OPENING TO 120°
■DIMENSION A = 95mm
OPENING FROM 120° TO 180°
■DIMENSION A = 65mm
INSTALLATION INSTRUCTIONS FOR
TOP JAMB (PUSH SIDE) MOUNTING
This installation process covers top jamb installations
up to 180° openings.
1. Select the door opening angle and use the dimensions shown opposite. Mark four holes on the frame
for the door closer and two holes on the door for the
arm shoe.
2. Drill 4mmØ pilot holes in the door and frame for the
fixings supplied.
3. Fix the forearm/arm shoe assembly to the door
using the fixings supplied.
4. Attach the closer to the door frame using the fixings
supplied.
Note: The speed adjusting valve must be positioned
towards the hinged edge of the door.
5. Install the main arm onto the top pinion shaft, perpendicular to the door as illustrated below. Tightly
secure it in place using the screw/washer assembly
supplied.
6. Adjust the length of the forearm so that it is perpendicular to the door frame when preloaded with the
main arm (see ‘top view’ illustration below). Secure
the forearm to the main arm using the screw/washer
assembly provided.
7. Snap the pinion cap over the pinion shaft at the bottom of the closer unit.
8. Adjust the closing speed of the door using the procedure detailed on page 5.
TOP JAMB INSTALLATION
Closer installs on frame-on
PUSH/STOP side of door
Illustrated
Left Hand Door-LH or
Right Hand Reverse-RHR
TYPICAL TOP VIEW
INSTALLATION
Page 4
- 4 -
■STOCK No.62894 ■ PART No.DC15/30
OPENING TO 120°
■DIMENSION A = 149mm ■ DIMENSION B = 119mm
OPENING FROM 120° TO 180°
■DIMENSION A = 119mm ■ DIMENSION B = 89mm
INSTALLATION INSTRUCTIONS FOR
PARALLEL ARM (PUSH SIDE) MOUNTING
This installation process covers parallel arm installations up to 180° openings.
1. Select the door opening angle and use the dimensions shown opposite. Mark four holes on the door
for the door closer and four holes on the underside
of the frame for the parallel bracket.
2. Drill 4mmØ pilot holes in the door and frame for the
fixings supplied.
3. Attach the closer to door using screws provided,
speed adjusting valve must be positioned away
from hinge edge.
4. Fix parallel arm bracket to the frame using fixings
provided.
5. Using a wrench on the square shaft at the bottom of
the closer, rotate the shaft 100mm to 125mm towards
the hinged edge of the door. Hold and place the
main arm of the shaft on top of the closer at the
index mark, as on “top view” illustration below.
For left hand door illustration A
For right hand door illustration B
Tighten arm screw with lockwasher securely.
6. Remove arm shoe from forearm and discard. Install
rod end of forearm to bracket using the
screw/washer assembly provided.
7. Adjust forearm length so that adjustable forearm is
parallel to the frame.
8. Adjust the closing speed of the door using the procedure detailed on page 5.
PARALLEL ARM INSTALLATION
Closer installs on
PUSH/STOP side of door
Illustrated
Left Hand Door-LH or
Right Hand Reverse-RHR
TYPICAL TOP VIEW
INSTALLATION
Page 5
- 5-
DOOR CLOSING CYCLE
CLOSING SPEED
Closing arcs are controlled by two separate speed adjusting valves. Adjust the closing speed first then
adjust the latching speed.
Turn the speed adjusting valve a full rotation clockwise for a slower closing speed.
Turn the speed adjusting valve a full rotation anticlockwise for a faster closing speed.
LATCHING SPEED
Turn the speed adjusting screw a full rotation clockwise for a slower latching speed.
Turn the speed adjusting screw a full rotation anticlockwise for a faster latching speed.
CAUTION: Do not turn speed adjusting valve more than two full turns anticlockwise from its factory set
position, as two speed adjusting valves could become dislodged from the door closer body, resulting with
the loss of internal fluid and failure of the device.
CHART
TO DETERMINE
HANG OF DOOR
Page 6
GENERAL INFORMATION
This manual has been compiled by Draper Tools and is an integrated part of the product, which should be kept with the product.
This manual describes the purpose for which this product has been designed and contains all the necessary information to ensure its
correct and safe use.We recommend that this manual is read before any operation of the product,before performing any kind of
adjustment to the product, and prior to any maintenance tasks. By following all the general safety instructions contained in this manual, it
will ensure both product and operator safety, together with longer life of the product itself.
All photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product.
Whilst every effort has been made to ensure accuracy of information contained in this manual,the Draper Tool policy of continuous
improvement determines the right to make modifications without prior warning.
DOOR CLOSER
• INSTRUCTIONS •
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO
ENSURE THE SAFE AND EFFECTIVE USE OF THIS TOOL.
■ STOCK No.62893 ■ PART No.DC25/45
08/2000
Page 7
- 2 -
■STOCK No.62893 ■ PART No.DC25/45
OPENING TO 120°
■DIMENSION A = 95mm
OPENING FROM 120° TO 180°
■DIMENSION A = 65mm
INSTALLATION INSTRUCTIONS FOR
REGULAR ARM (PULL SIDE) MOUNTING
This installation process covers regular arm
installations up to 180° openings.
1. Select the door opening angle and use the
dimensions shown opposite. Mark four holes on the
door for the door closer and two holes on the frame
for the arm shoe.
2. Drill 4mmØ pilot holes in the door and frame for the
fixings suppied.
3. Fix the forearm/arm shoe assembly to the door
frame using the fixings supplied.
4. Attach the closer to the door using the fixings
supplied.
Note: The speed adjusting valve must be positioned
towards the hinged edge of the door.
5. Install the main arm onto the top pinion shaft,
perpendicular to the door as illustrated below.
Tightly secure it in place using the screw/washer
assembly supplied.
6. Adjust the length of the forearm so that it is
perpendicular to the door frame when assembled to
preloaded main arm (see ‘top view’ illustration
below). Secure the forearm to the main arm using
the screw/washer assembly provided.
7. Snap the pinion cap over the pinion shaft at the
bottom of the closer unit.
8. Adjust the closing speed of the door using the
procedure detailed on page 5.
REGULAR ARM INSTALLATION
Closer installs on PULL/HINGE side of door
Illustrated
Left Hand Door-LH or
Right Hand Reverse-RHR
TYPICAL TOP VIEW
INSTALLATION
Page 8
- 3 -
■STOCK No.62893 ■ PART No.DC25/45
OPENING TO 120°
■DIMENSION A = 95mm
OPENING FROM 120° TO 180°
■DIMENSION A = 65mm
INSTALLATION INSTRUCTIONS FOR
TOP JAMB (PUSH SIDE) MOUNTING
This installation process covers top jamb installations
up to 180° openings.
1. Select the door opening angle and use the
dimensions shown opposite. Mark four holes on the
frame for the door closer and two holes on the door
for the arm shoe.
2. Drill 4mmØ pilot holes in the door and frame for the
fixings supplied.
3. Fix the forearm/arm shoe assembly to the door
using the fixings supplied.
4. Attach the closer to the door frame using the fixings
supplied.
Note: The speed adjusting valve must be positioned
towards the hinged edge of the door.
5. Install the main arm onto the top pinion shaft,
perpendicular to the door as illustrated below.
Tightly secure it in place using the screw/washer
assembly supplied.
6. Adjust the length of the forearm so that it is
perpendicular to the door frame when preloaded
with the main arm (see ‘top view’ illustration below).
Secure the forearm to the main arm using the
screw/washer assembly provided.
7. Snap the pinion cap over the pinion shaft at the
bottom of the closer unit.
8. Adjust the closing speed of the door using the
procedure detailed on page 5.
TOP JAMB INSTALLATION
Closer installs on frame-on
PUSH/STOP side of door
Illustrated
Left Hand Door-LH or
Right Hand Reverse-RHR
TYPICAL TOP VIEW
INSTALLATION
Page 9
- 4 -
■STOCK No.62893 ■ PART No.DC25/45
OPENING TO 120°
■DIMENSION A = 149mm ■ DIMENSION B = 119mm
OPENING FROM 120° TO 180°
■DIMENSION A = 119mm ■ DIMENSION B = 89mm
INSTALLATION INSTRUCTIONS FOR
PARALLEL ARM (PUSH SIDE) MOUNTING
This installation process covers parallel arm
installations up to 180° openings.
1. Select the door opening angle and use the
dimensions shown opposite. Mark four holes on the
door for the door closer and four holes on the
underside of the frame for the parallel bracket.
2. Drill 4mmØ pilot holes in the door and frame for the
fixings supplied.
3. Attach the closer to door using screws provided,
speed adjusting valve must be positioned away
from hinge edge.
4. Fix parallel arm bracket to the frame using screws
provided.
5. Using a wrench on the square shaft at the bottom of
the closer, rotate the shaft 100mm to 125mm towards
the hinged edge of door. Hold and place the main
arm of the shaft on top of the closer at the index
mark, as on “top view” illustration below.
For left hand door illustration A
For right hand door illustration B
Tighten arm screw with lockwasher securely.
6. Remove arm shoe from forearm and discard. Install
rod end of forearm to bracket using the
screw/washer assembly provided.
7. Adjust forearm length so that adjustable forearm is
parallel to the frame.
8. Adjust the closing speed of the door using the
procedure detailed on page 5.
PARALLEL ARM INSTALLATION
Closer installs on
PUSH/STOP side of door
Illustrated
Left Hand Door-LH or
Right Hand Reverse-RHR
TYPICAL TOP VIEW
INSTALLATION
Page 10
- 5 -
DOOR CLOSING CYCLE
CLOSING SPEED
Closing arcs are controlled by two separate speed adjusting valves. Adjust the closing speed first then
adjust the latching speed.
Turn the speed adjusting valve a full rotation clockwise for a slower closing speed.
Turn the speed adjusting valve a full rotation anticlockwise for a faster closing speed.
LATCHING SPEED
Turn the speed adjusting screw a full rotation clockwise for a slower latching speed.
Turn the speed adjusting screw a full rotation anticlockwise for a faster latching speed.
CAUTION: Do not turn speed adjusting valve more than two full turns anticlockwise from its factory set
position, as two speed adjusting valves could become dislodged from the door closer body, resulting with
the loss of internal fluid and failure of the device.
CHART
TO DETERMINE
HANG OF DOOR
Page 11
GENERAL INFORMATION
This manual has been compiled by Draper Tools and is an integrated part of the product, which should be kept with the product.
This manual describes the purpose for which this product has been designed and contains all the necessary information to ensure its
correct and safe use.We recommend that this manual is read before any operation of the product,before performing any kind of
adjustment to the product, and prior to any maintenance tasks. By following all the general safety instructions contained in this manual, it
will ensure both product and operator safety, together with longer life of the product itself.
All photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product.
Whilst every effort has been made to ensure accuracy of information contained in this manual,the Draper Tool policy of continuous
improvement determines the right to make modifications without prior warning.
DOOR CLOSER
• INSTRUCTIONS •
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO
ENSURE THE SAFE AND EFFECTIVE USE OF THIS TOOL.
■ STOCK No.62892 ■ PART No.DC40/65
08/2000
Page 12
- 2 -
■STOCK No.62892 ■ PART No.DC40/65
OPENING TO 120°
■DIMENSION A = 120mm
OPENING FROM 120° TO 180°
■DIMENSION A = 80mm
INSTALLATION INSTRUCTIONS FOR
REGULAR ARM (PULL SIDE) MOUNTING
This installation process covers regular arm
installations up to 180° openings.
1. Select the door opening angle and use the
dimensions shown opposite. Mark four holes on the
door for the door closer and two holes on the frame
for the arm shoe.
2. Drill 4mmØ pilot holes in the door and frame for the
fixings supplied.
3. Fix the forearm/arm shoe assembly to the door
frame using the fixings supplied.
4. Attach the closer to the door using the fixings
supplied.
Note: The speed adjusting valve must be positioned
towards the hinged edge of the door.
5. Install the main arm onto the top pinion shaft,
perpendicular to the door as illustrated below.
Tightly secure it in place using the screw/washer
assembly supplied.
6. Adjust the length of the forearm so that it is
perpendicular to the door frame when assembled to
preloaded main arm (see ‘top view’ illustration
below). Secure the forearm to the main arm using
the screw/washer assembly provided.
7. Snap the pinion cap over the pinion shaft at the
bottom of the closer unit.
8. Adjust the closing speed of the door using the
procedure detailed on page 5.
REGULAR ARM INSTALLATION
Closer installs on PULL/HINGE side of door
Illustrated
Left Hand Door-LH or
Right Hand Reverse-RHR
TYPICAL TOP VIEW
INSTALLATION
Page 13
- 3 -
■STOCK No.62892 ■ PART No.DC40/65
OPENING TO 120°
■DIMENSION A = 120mm
OPENING FROM 120° TO 180°
■DIMENSION A = 80mm
INSTALLATION INSTRUCTIONS FOR
TOP JAMB (PUSH SIDE) MOUNTING
This installation process covers top jamb installations
up to 180° openings.
1. Select the door opening angle and use the
dimensions shown opposite. Mark four holes on the
frame for the door closer and two holes on the door
for the arm shoe.
2. Drill 4mmØ pilot holes in the door and frame for the
fixings supplied.
3. Fix the forearm/arm shoe assembly to the door
using the fixings supplied.
4. Attach the closer to the door frame using the fixings
supplied.
Note: The speed adjusting valve must be positioned
towards the hinged edge of the door.
5. Install the main arm onto the top pinion shaft,
perpendicular to the door as illustrated below.
Tightly secure it in place using the screw/washer
assembly supplied.
6. Adjust the length of the forearm so that it is
perpendicular to the door frame when preloaded
with the main arm (see ‘top view’ illustration below).
Secure the forearm to the main arm using the
screw/washer assembly provided.
7. Snap the pinion cap over the pinion shaft at the
bottom of the closer unit.
8. Adjust the closing speed of the door using the
procedure detailed on page 5.
TOP JAMB INSTALLATION
Closer installs on frame-on
PUSH/STOP side of door
Illustrated
Left Hand Door-LH or
Right Hand Reverse-RHR
TYPICAL TOP VIEW
INSTALLATION
Page 14
- 4 -
■STOCK No.62892 ■ PART No.DC40/65
OPENING TO 120°
■DIMENSION A = 200mm ■ DIMENSION B = 170mm
OPENING FROM 120° TO 180°
■DIMENSION A = 170mm ■ DIMENSION B = 140mm
INSTALLATION INSTRUCTIONS FOR
PARALLEL ARM (PUSH SIDE) MOUNTING
This installation process covers parallel arm
installations up to 180° openings.
1. Select the door opening angle and use the
dimensions shown opposite. Mark four holes on the
door for the door closer and four holes on the
underside of the frame for the parallel bracket.
2. Drill 4mmØ pilot holes in the door and frame for the
fixings supplied.
3. Attach the closer to door using screws provided,
speed adjusting valve must be positioned away
from hinge edge.
4. Fix parallel arm bracket to the frame using screws
provided.
5. Using a wrench on the square shaft at the bottom of
the closer, rotate the shaft 100mm to 125mm towards
the hinged edge of door. Hold and place the main
arm of the shaft on top of the closer at the index
mark, as on “top view” illustration below.
For left hand door illustration A
For right hand door illustration B
Tighten arm screw with lockwasher securely.
6. Remove arm shoe from forearm and discard. Install
rod end of forearm to bracket using the
screw/washer assembly provided.
7. Adjust forearm length so that adjustable forearm is
parallel to the frame.
8. Adjust the closing speed of the door using the
procedure detailed on page 5.
PARALLEL ARM INSTALLATION
Closer installs on
PUSH/STOP side of door
Illustrated
Left Hand Door-LH or
Right Hand Reverse-RHR
TYPICAL TOP VIEW
INSTALLATION
Page 15
- 5 -
DOOR CLOSING CYCLE
CLOSING SPEED
Closing arcs are controlled by two separate speed adjusting valves. Adjust the closing speed first then
adjust the latching speed.
Turn the speed adjusting valve a full rotation clockwise for a slower closing speed.
Turn the speed adjusting valve a full rotation anticlockwise for a faster closing speed.
LATCHING SPEED
Turn the speed adjusting valve a full rotation clockwise for a slower latching speed.
Turn the speed adjusting valve a full rotation anticlockwise for a faster latching speed.
CAUTION: Do not turn speed adjusting valve more than two full turns anticlockwise from its factory set
position, as the speed adjusting valves could become dislodged from the door closer body, resulting with
the loss of internal fluid and failure of the device.
DELAY ACTION
Turn the delay adjusting valve a full rotation clockwise for a greater delay time before door closes.
BACK CHECK
Turn the back check adjusting valve clockwise to reduce the opening capacity. This function is to avoid
the door, handle or door closer coming in contact with a wall etc.
CHART
TO DETERMINE
HANG OF DOOR
LATCHING
SPEED
CLOSING
SPEED
DELAY
ACTION
BACK CHECK
BACK CHECK
Page 16
YOUR DRAPER STOCKIST
©Published by Draper Tools Ltd.
No part of this publication may be reproduced,
stored in a retrieval system or transmitted in any
form or by any means, electronic, mechanical
photocopying, recording or otherwise without
prior permission in writing from Draper Tools Ltd.
www.draper.co.uk
e-mail: sales@draper.co.uk
DRAPER TOOLS LIMITED,
Hursley Road, Chandler's Ford, Eastleigh, Hants. SO53 1YF. U.K.
Helpline: (023) 8049 4344.
Sales Desk: (023) 8049 4333.
General Enquiries: (023) 8026 6355.
Fax: (023) 8026 0784.
Loading...