DRAPER Clarion HDTV (9:16) 302/119"" 147*264 XT1000V (M1300) Vel-Tex edgelessclarion_inst.pdf

Installation Instructions

Top section

Side section

Bottom section

Side section

Screw locations for
assembling frame

Back view of ShadowBox Clarion

Front of Screen

Patch

Upper Wall Bracket

Top Frame Section

Viewing Direction

Bottom Frame Section

Lower Wall Bracket

Top Frame

Section

13

/16"

1

/2"

Bottom Frame

Section

1

/2"

2

1

/2"

13

/16"

2"

Edgeless Clarion Screen by Draper

Caution

1 Read instructions through completely before proceeding.
2 Follow instructions carefully. Installation contrary to instructions

invalidates warranty.
3 Screen should be accessible for complete removal should fabric
become damaged or should other service be required.

4 Screen should be installed level (using a carpenter’s level).
5 Nothing should be fastened to screen frame or viewing surface.
6 Tools required: Medium (#2) Phillips Screwdriver, Carpenters Level, and

Measuring Tape.

7 Open carton along the length, not at ends.
8 The ideal temperature range for assembling folding screens to prevent

damaging the surface is 68°-78° F (20°-26° C). Assembling below
recommended temperatures may damage surface and void warranty.
NOTE: Screen has been thoroughly inspected and tested at factory and
found to be operating properly prior to shipment.

1 Remove all pieces from the carton.
2 Lay out the sections of the frame by matching up the numbers located on

the back of the frame sections. Snaps should be facing up. Slide the ends
of the castings from the top section into the side frame sections. Fasten
these together using the 1/4"-20 machine screws provided. Repeat this for
bottom section of frame (see Fig. 1).

4 Remove frame from wall by pushing upward until the bottom frame section
hits the lower wall brackets. The top frame section should clear the studs
of the upper brackets; pivot the top of the frame away from the wall until
frame drops down in front of these brackets. The bottom of the frame will
then be disengaged from the lower wall brackets. Set frame aside.

5 Make sure your hands are clean before touching the viewing surface.
6 Remove the viewing surface from the cardboard tube. Unroll the surface

from the small cardboard tube. NOTE: Be extremely careful to protect the
viewing surface by making sure it is unrolled onto a clean cloth or paper.

7 Place the frame with snaps facing up onto the viewing surface, centering it
as much as possible. Be sure to match the top of the frame with the top of
the viewing surface. Starting away from the corners, wrap surface around
the frame and snap onto the back of the frame working toward the corners
(see diagram on page 2). Viewing surface should completely cover the
front of the frame. The side of the castings at each corner may be slightly
visible due to viewing surface elasticity. It may be necessary to unsnap a
portion of the surface to get the proper coverage at the corners. Pull the
surface in the desired direction and snap it on the frame. After the surface
has been adjusted (if necessary) and completely snapped onto the frame,
peel off the liner on the corner patch and place it on the screen fabric at
each corner to conceal any gap (see Fig. 4). These patches may not be
necessary if outside edges of screen are not visible after installation.

3 Position the upper wall brackets (with short stud) on the wall at desired
height and correct distance apart. Determine distance apart by measuring
the distance between the grommeted holes in top section of the frame.
When the frame is positioned on these brackets, the top of the frame is 2"
above the top edge of the upper brackets (see Fig. 2). Make sure these
brackets are level with each other. Installer must insure that the fasteners
are of adequate strength and suitable for the mounting surface chosen
(fasteners not provided). Position the frame on the upper brackets by
inserting the studs into the grommeted holes. Position the lower wall
brackets (with long stud) so that the stud is inserted into the grommeted
holes in the bottom frame section. Fasten these brackets to the wall
leaving 21/2" between the bottom of this bracket and the furthest edge of
bottom frame section (see Fig. 3).

Figure 2

Figure 1

Figure 4

8 Carefully mount the frame on the wall brackets. With the screen tilted out
slightly at the top, engage the bottom frame section with the studs on the
lower wall brackets. Push the frame up until the top section of the frame is
above the upper wall brackets, then tilt the frame toward the wall. Push the
frame down until the studs completely engage with the holes in the top
frame section. When properly installed, the frame should be engaged with
all of the wall brackets (see Fig. 5).

Figure 3

Copyright ©2013 Draper Inc. Form EdgelessClarion_Inst13 Printed in U.S.A.

®

Figure 5

Continued on back page

If you encounter any difficulties installing or servicing your Edgeless Clarion Screen, contact
your dealer or Draper, Inc., Spiceland, Ind., [phone]; or fax [phone].

Edgeless Clarion Instructions by Draper page 2 of 2

www

9

To attach the viewing surface to your Edgeless Clarion Projection Screen, begin in the corners, then snap along
the frame. See the below drawing.

1

2

7

8

6

5

.draperinc.com

4

3

(765) 987-799