DRAPER Access FIT/E (16:10) 137"" 184*295 XH800E, Access FIT/V HDTV (9:16) 269/106"" 132*234 XT1000V (M1300) ebd 30 AccessFit_220V_Inst.pdf

PENCIL

HARDWARE

Access FIT E and V 220V

Electric projection screen

Overview - Components

INSTRUCTIONS

INSTAL L AT I ON & OPE R ATI O N

Mounting Bracket

Electrical

Cutout

Tab Tensioning

“V” Dowel

Hoisting Bracket

“V” Flexible Vinyl

Viewing Surface

Shipping Brackets Attached
to Dowel and Screen Case

(V Screens Only)

Please Note: Shipping brackets must remain

in place until product has been mounted and
connected to power

document.)

Also, DO NOT operate screen before removing
shipping brackets from screen case.

.

(see Sections 1 and 4 in this

Leveling Brackets

Hoisting Bracket

“E” Free Hanging

Viewing Surface

TOOLS REQUIRED

POWER DR ILL

(by others)

LEVEL

Mounting Bracket

Trim Flange

“E” Dowel

TAPE MEASURE

CAUTION

Read and understand all warnings

Contents

Overview - Components .......................................................................................1

Section 1 - Removing Shipping Brackets

PLEASE READ - Safety Information ....................................................................2

Section 2 - Hanging Screen .................................................................................3

Section 3 - Bottom Access FIT Panel Installation/Removal ..........................3

Section 4 - Motorized Roller/Fabric Installation ..............................................4

Section 5 - Motorized Roller/Fabric Removal ...................................................4

(Tab-Tensioned, "V" Surfaces only)

.......2

(Page 2)

before beginning installation.

Section 6 - Operation............................................................................................5

Section 7 - Tab-Tension Adjustment Procedure ..............................................5

Section 8 - Limit Adjustments .............................................................................6

Section 9 - Case Length Dimensions .................................................................7

Section 10 - Case Width Dimensions .................................................................7

Section 11 - Mounting Bracket Dimensions......................................................7

Section 12 - Wiring Diagrams: 220V Standard Motor ......................................8

If you have any difficulties installing or servicing your

Access FIT screen, call your dealer or Draper, Inc.

Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385

draperinc.com | 765.987.7999 | 800.238.7999

© 2021 All Rights Reserved | FORM: AccessFit_220V_Inst20

dowel endcap

Access FIT E and V 220V

page 2 of 8

Section 1 - Removing Shipping Brackets

CAUTION: DO NOT remove shipping

brackets until product has been
mounted and connected to power

Section 4 in this document.)

Also, DO NOT OPERATE SCREEN
BEFORE REMOVING SHIPPING
BRACKETS FROM SCREEN CASE.

.

(see

1

PLEASE READ - Safety Information

(Tab-Tensioned, "V" Surfaces only)

Remove
fasteners from
bracket clamps.

Run screen
DOWN to expose

2

dowel screws.

Loosen screws
and remove
shipping bracket.

3

Retighten

4

screws.

Important Safety Information Important Safety Information

Improper installation and use of Access Fit E & Vscreen can result in serious injury or death. Primarily, injuries can occur if the unit falls due to imprecise
installation, mishandling of the unit during installation, or installation on an insufficient wall or ceiling structure. Please use extreme care.

1.

Please read the following installation guidelines thoroughly and follow them
carefully. Failure to do so may cause product to fall or otherwise fail, and could
result in serious injury.

2.

Installation and calibration of the unit should only be per formed by an
authorized, qualified, and experienced professional. In particular, electrical
work and wiring [indicated in diagram by dashed lines] must be completed only
by a qualified professional electrician who has read this manual completely
and is familiar with the construction and operation of this equipment and the
hazards involved.

3.

Do not affix the unit to walls or ceilings that have inadequate strength
to permanently hold the unit during use. It is the owner’s and installer’s
responsibility to confirm the wall or ceiling to which the unit attaches is
sufficient to permanently hold the weight and stress loads of the unit at all
times. Draper, Inc., is not responsible for improper installation, application,
testing, or workmanship related to the product at place of installation.

4.

It is the installer’s responsibility to make sure appropriate fasteners are used
for mounting.

5.

All hardware must be installed level. Unit must be level and square.

6.

Never leave the area while operating the unit during installation, maintenance,
or normal operation, unless it is secure and safe.

7.

Before testing or operation, carefully inspect the entire area and path

underneath)

of unit to be sure no persons or objects are in the area.

WARNING

8.

Turn off power and any nearby equipment or cables carrying electricity before
connecting switches, wires, controls, or electrical components.

9.

Do not wire motors in parallel without written permission from Draper, Inc.

10.

During testing or operation, carefully watch the surrounding area for any
potential safety concerns including nearby persons or objects.

11.

After installation, the entire system, including all sensors, should be carefully
tested to ensure safe and normal operation. Extreme care should be taken
during testing to remain clear of moving parts to avoid possible injury.

12.

Operation of unit should be performed only by authorized and qualified
personnel, who have been trained in its safe and effective operation and
understand its safety features.

13.

The safety features of the unit should never be disabled, bypassed, or
overridden. The system should not be operated until all safety features are
properly and completely installed, calibrated, and tested.

14.

Unit may need to comply with local, state, or district rules and regulations, in
particular when installed in schools. All applicable rules and regulations should
be reviewed before installation and use.

15.

Failure to precisely follow installation guidelines invalidates all
warranties.

(especially

16.

Custom products/installations may not be reflected in this manual. Call Draper,
Inc., if you have questions about the installation of custom products or any
questions about your installation.

Before Beginning Installation

1.

Look for any job site conditions that could interfere with installation or
operation of the system.

2.

Read carefully and be sure to understand all installation instructions and
all related operations manuals. These instructions are intended to ser ve
as a guide for the installer and owner. They should be followed closely and
combined with the expertise of experienced qualified installers. Draper, Inc., is
not responsible for improper installation, application, testing, or workmanship
related to the product at place of installation. Please retain all instructions for
future use.

3.

Open cartons lengthwise.

4.

Locate and lay out all pieces.

5.

Inspect all boxes to make sure you have received the proper unit and parts.
Controls may be shipped separately, or in same carton as unit.

6.

If you have any difficulties with installing, servicing, or operating your unit,
call your dealer or Draper, Inc., 765-987-7999.

Bottom flange of
Access housing

Bottom Access Panel Door

CAUTION: Beware of pinch points at ends of closure

HOISTING
BRACKET

CASE
MOUNTING
BRACKET

CASE
MOUNTING
BRACKETS

7⁄8" (22 mm)

ELECTRICAL
KNOCKOUT

ALTERNATE
INSTALLATION

Additional set of brackets
required, but NOT included.

TYPICAL
INSTALLATION

With typical installation, brackets
may be angled to meet installation requirements.

Access FIT E and V 220V

Section 2 - Hanging Screen

Please Note: When locating viewing surface and checking clearance for screen operation, ensure that surface is centered in the case.

1.

Engage each case mounting bracket

2.

Screen should be sufficiently supported to withstand
vibration.

Please Note: A hoisting bracket is included on each end of the

case to aid in overhead installation.

3.

Ensure that fasteners are of adequate strength and suitable
for the mounting surface chosen. Supporting hardware
such as chains, cables, two
precisely vertical.

4.

Entire bottom of case must be readily accessible after
installation is complete.

5.

Front, back, and top of case must be straight—not forced
to warp or bow.

CAUTION: Screen case and flange are not designed to

serve as ceiling support.

6.

Do not seal unit in ceiling until electrical connections have
been made and screen operates successfully.

Please Note: If case is painted on location, removal of roller/

fabric assembly is recommended prior to painting. If not
removed, slot on bottom of case should be shielded to
protect viewing surface from paint splatters/overspray.

3/8

"

(9.5 mm)

(attached to case)

with top of housing

rods, etc., must be

(Fig. 2)

and tighten set screws.

page 3 of 8

ALTERNATE
INSTALLATION

Additional set of brackets
required, but NOT included.

Figure 2

Installation of Case

CASE
MOUNTING
BRACKETS

Section 3 - Bottom Access FIT Panel Installation/Removal

CAUTION: For larger sizes, the following requires two people to perform safely.

1.

Press up on Access FIT panel and pull toward the front of the
screen housing to disengage hinges and remove Access FIT panel.

SCREEN

HOUSING

Remove Screws

from both ends
of Screen Housing.

Access
Panel Door:

Pivot on Hinges.

CLOSED

ACCESS PANEL

ACCESS

OPEN

PANEL

Figure 4

Removing Access Panel

Bottom Access FIT panel secures to the screen housing
with two screws
position by engagement brackets with ball detents that
snap into case support brackets

Figure 3

Access case as seen from below

2.

(one on each end)

, and held in the closed

(Fig. 3)

.

To Remove/Install Support Brackets:

CENTER

of CASE

CENTER of CASE

Access Panel
Support Bracket

Attaching Brackets:

Insert pin in top

1

slot and push up.

Rotate bracket

2

clockwise to lock
bracket in place.

Engagement Bracket
With Ball Detent:

will snap into Access
Panel Support Bracket.

Access FIT E and V 220V

Figure 5

page 4 of 8

MOTOR END OF CASEIDLER END OF CASE

BOTTOM VIEWBOTTOM VIEW

SIDE VIEWSIDE VIEW

Idler End
Mounting
Bracket

Motor End
Mounting
Bracket

Set Screws

Figure 6 Figure 7

Idler End

Retaining

Clip

Motor End

Retaining Clip

Section 4 - Motorized Roller/Fabric Installation

Please note: When ordering motor with internal Low-Voltage Controller, if case ships separately from contents, case includes 25'

and special low-voltage switch.

1.

Remove bottom Access FIT panel

2.

Back out set screws from top side of motor mounting brackets

3.

To engage motor end bracket flange
motor bracket to rest flat against top inside housing.

4.

Rotate bracket clockwise until it engages in channel.

5.

Engage idler end bracket in same manner as motor end bracket and slide toward opposite end of screen housing.

CAUTION: Step 6 requires two people to perform safely.

6.

Locate black washer and retaining clips attached to instruction sheet. Lift roller/fabric assembly into screen housing and engage motor head completely into motor
bracket, making sure limit switch adjusting knobs are visible from bottom of screen housing.

Please Note: If snap ring is provided, make sure it engages with motor. If retaining clip is provided instead, install to lock motor end in place.

(See Section 3)

(above the two cha nnel s in the top of the scr een housing)

.

(See Fig 5)

.

, rotate bracket approximately 45° counterclockwise to allow top surface of

(7. 6 m)

cable

7.

Support idler end of roller and slide mounting bracket toward roller. Insert roller pin into nylon bushing on idler bracket.

8.

Roller idler pin goes through idler bracket. Reinstall washer and retaining clip.

CAUTION: Failure to replace washer and retaining clip could result in separation of roller from brackets.

9.

Center roller/fabric assembly by sliding mounting brackets left or right.

10.

Securely tighten set screws on roller mounting brackets.

11.

Connect electrical plug from motor to mating socket on junction box.

12.

Attach door support brackets.

13.

Reinstall bottom access panel as previously described.

Section 5 - Motorized Roller/Fabric Removal

Reverse the previous instructions

("Motorized Roller/Fabric Installation")

for removal of unit.

Access FIT E and V 220V

page 5 of 8

Section 6 - Operation

CAUTION: When operating for the first time, cycle unit down and up several times to confirm satisfactory operation. Be prepared to cut POWER if necessary.

•

220V SINGLE STATION CONTROL - 3-position UP-OFF-DOWN switch permits operation to be stopped at any point. Factory adjusted limit switches

automatically stop screen when fully down or fully up.

•

24V CONTROL - 3-button UP-STOP-DOWN switches stop at any point desired and operate in any sequence. Factor y adjusted limit switches automatically stop

screen when fully up or fully down. Installer should incorporate an all-pole disconnect in fixed wiring available with RF or IR remote.

•

KEY OPERATED SWITCHING - Two key-operated switches optionally available with this unit:

•

Key-operated power supply switch controls power to screen and switches. When “off”, switches will not operate screen.
Key may be removed from switch in either "on" or "off" position.

•

Three-position key switch permits the screen to be operated directly by key. Requires screen operator to have a key.

•

RS232 / ETHERNET - Serial communication and network communication optionally available.

Section 7 - Tab-Tension Adjustment Procedure

Please Note: Draper’s Tab-Tensioning System is factory-set, and under normal

circumstances will not require field adjustment. If wrinkles are observed,
however, follow the adjustment procedure shown in Figure 8.

Figure 8

END OF
DOWEL

PUSH & TURN

COUNTER-CLOCKWISE

to RELEASE TENSION

END OF
DOWEL

PUSH & TURN

CLOCKWISE

to INCREASE TENSION

Left hand motor:

Right hand motor:

aterfall RollStandar

DOWN Limit (I)
Clockwise decreases
down travel.

UP Limit (II)
Counterclockwise
increases up travel.

Access FIT E and V 220V

Section 8 - Limit Adjustments

Section 8 - Limit Adjustments

page 6 of 8

Please Note: Screen limits

are factory set for optimum
performance of the screen. Any
adjustment of these limits could
void the warranty. Please check
with Draper prior to resetting
screen limits.

Please Note: If Access screen

is “Right Hand Motor” or
“Waterfall,” the WHITE/DOWN
and YELLOW/UP
are reversed

CAUTION:

- Be sure all switches are in “off”
position before adjusting limit
switches.

- Be prepared to shut off manually
while testing.

(Fig. 9)

(II)

limit screws

.

Figure 10

Motor
End

Audience

Side

d Roll

White Socket—Down
Yellow Socket—Up

White Socket—Up
Yellow Socket—Down

Motor
End

Reverse Roll

Left hand motor:

White Socket—Down
Yellow Socket—Up

Right hand motor:

White Socket—Up
Yellow Socket—Down

+

(I)

lI

- Screen may be damaged by

- Motor must be installed so that

Back

Side

I

+

lowering it too far and
exposing roller.

limit switches are pointed down.

Motor
End

W

Left hand motor:

White Socket—Up
Yellow Socket—Down

Right hand motor:

White Socket—Down
Yellow Socket—Up

Figure 9

DOWN Limit

Clockwise
decreases
down travel.

UP Limit

Counterclockwise
increases up travel.

Audience

Side

(I)

:

(II)

:

Section 8.1 - Somfy Motors Limit Adjustments

Section 8.1.1 - "Down" Limit Adjustment

To Reduce Screen Drop:

1.

Raise screen surface approximately 1'
turn off.

2.

Turn DOWN

3.

Test by lowering screen. Repeat steps 1 & 2 until desired position is
reached.

To Increase Screen Drop:

1.

Lower screen to down limit.

2.

With down switch on, turn DOWN

(3 screw turns = ½ roller revolution)

3.

Test by raising screen approximately 1'
down limit.

4.

Repeat steps 2 and 3 until desired position reached.

Please Note: For Quiet Motor with alternate limit screws:

WHITE screw = UP and RED screw = DOWN.
However, limits are reversed if surface is waterfall rolled

(I)

limit screw clockwise

to increase drop.

(3 screw turns = ½ roller revolution)

(I)

limit screw counterclockwise

(Fig. 9)

(requires

5/32

" (4 mm) Allen wrench)

(30 cm)

above desired setting and

(30 cm)

then down to new

(Fig. 10)

.

Section 8.1.2 - "Up" Limit Adjustment

If Screen Raises Too High:

1.

Lower screen surface approx. 1'

2.

Turn UP

(II)

limit screw clockwise

3.

Test by advancing screen up.

4.

Repeat steps 1 through 3 until desired position is reached.

If Screen Needs to Raise Higher:

1.

Lower screen surface approx. 1'

2.

With UP switch on, turn UP

(3 screw turns = ½ roller revolution)

3.

Repeat steps 1 and 2 until desired position is reached.

CAUTION: DO NOT allow dowel to wrap over roller when operating screen!

This could damage screen.

(30 cm)

below desired setting and turn off.

(3 screw turns = ½ roller revolution).

(30 cm)

below desired setting and turn off.

(II)

limit screw counterclockwise

.

.

Section 8.2 - ILT Motors with Internal Low-Voltage Control Limit Adjustments

Please Note: Hold STOP button for 3-5 seconds while in

programming mode to reverse motor direction.

Figure 11

BACK VIEW OF WALL SWITCH

To Motor

with
Built-In (ILT)
Low Voltage

Slide

Switch

C
o
m

+

m

5V

To Motor

Built-In (ILT)
Low Voltage

Please Note: 5V DC must be connected to

be able to set limits using the wall switch.

o

DC

n

with

POSITION FUNCTION

DOWN Set LOWER limit

UP Set UPPER limit

CENTER Normal Operation

D
o
w
n

1.

Connect ILT switch to motor via terminal blocks, or via
modular port using a four conductor modular cable. When
using modular cable, cable connectors MUST NOT be
crimped in reverse, as with standard telephone cable.

(For Dr y Contacts Wir ing Diagram, see Section 12.)

2.

Set slide switch to lower position. Hold DOWN button to
move viewing surface to desired lower limit. If screen moves
in opposite direction, release DOWN button and hold STOP
button for 4 seconds. This reverses operation of UP and
DOWN switches.

3.

U
p

Move slide switch into center position. Wait several seconds.

Please Note: Do Not move slide switch from DOWN to UP

in one motion. This will set limits in same position.

4.

Set slide switch to higher position. Move viewing surface to
desired upper limit by holding UP button on wall switch.

5.

Return slide switch to center position to resume normal
operation.

6.

To set viewing surface to alternate format position, move
viewing surface to desired position and press STOP button.
Hold STOP button for at least 3 seconds to record position.

Please Note: When ordering a motor with internal low-voltage controller, if case ships

separate from "guts," it includes 25'

(F i g . 11)

(7. 6 m)

cable and special low-voltage switch.

Please Note: Press and release UP

button on switch to move screen to
upper limit. Press and release DOWN
button to move screen to lower limit.

• While motor is in motion, press
STOP button for less than 2
seconds to stop viewing sur face at
present position.

• Once motor is stopped, press
STOP button to move viewing
surface to alternate format position.

• Hold STOP button, when motor is
at rest or in motion, for 3-5
seconds to record new alternate
format position.

• Hold STOP button for 3-5 seconds
while in programming mode to
reverse motor direction.

ACCESS FIT

Standard Motor Wiring is on the

AUDIENCE LEFT END of Screen Case.

3"

(76mm)



"

(13m m)

4



"

(124mm)

6



"

(164 mm)

5



"

(130mm)



"

(11mm)

2"

(51mm)

7 "

(197mm)



"

(22mm)



"

(16mm)



"

(16mm)

5



"

(144mm)

ACCESS FIT

AUDIENCE LEFT END of Screen Case.

"

(11m m)

1"

(35mm)

7 "

(197mm)

6 "

(165 mm)

3  "

(87mm)

Access FIT E and V 220V

Section 9 - Case Length Dimensions

CASE LENGTH



"

(19mm)

18"

(457mm)

of Case

Center

8"

(203mm)

18"

(457mm)

1



(35mm)

" TYP

5



(137mm)

page 7 of 8

LEVELING BRACKET**



"

(22mm)

"

L*



"

(19mm)

*L = Varies

Section 10 - Case Width Dimensions Section 11 - Mounting Bracket Dimensions

5



"

(144mm)

Series V

Viewing Surface

• For minimum length of ceiling cutout: subtract 1 ¼"

• For minimum width of cutout

• ** Leveling bracket is used to level the case and should NOT be used to support the weight of the unit.

• The leveling bracket is screwed to the side of the case. Hardware used for leveling provided by others.

• There are several knock-outs in the screen housing to allow the Leveling Bracket to be adjusted laterally up to 16"

7 "

(197mm)



"

(13m m)

(fron t to back)



(11mm)

2"

(51mm)

(32mm)

from case length

: see case width dimensions below.

(meas ured f rom out er edge of flange s)

"

Series E

Viewing Surface

L*

L*



"

(19mm)

1



"

(41mm)

.

(40. 6cm)

in either direction.

3"

(76mm)



"

(22mm)

4

6







"

(16mm)

Standard Motor Wiring is on the

"

(124mm)

"

(164 mm)



(16mm)

5



"

(130mm)

"

50 Hz.

)

Single Station Control

220V Motor and Quiet Motor

To 220V Line

ILT Data Cable Connection

Dry Contacts

ch

all Switch

GND

Internal LVC-IV - Single or Multiple Projection Screen Wiring Diagram

Access FIT E and V 220V

page 8 of 8

Section 12 - Wiring Diagrams: 220V Standard Motor

CE Approved

Internal S creen Wiring
Blue-220V (Common)
Brown-220V (Down)
Black-220V (Up)

Green/ Yellow (Motor Ground

Control
switch

* These wiring diagrams

Dashed wiring
by installer.

Neutral

220V,

T

O

M

O

T

O

are for Access screens
with motor on audience

L1

left

(standard)

unrolling from the back of
the roller

R

MOTOR

DATA CABLE

, and fabric

(standard)

Data Cables to
switches or
additional motors

Please Note: Do not wire motors in parallel.

.

T

O

M

O

with Internal Low-Voltage Controller

Internal Screen Wiring

Blue (Neutral)

Brown

Green (Ground)

Dashed wiring
by electrician

Data
Cables

Wall Switches,

RF or IR

Receivers,

or integrated

control systems.

T

O

R

MOTOR

DATA CABLE

Connecting Switch
to ILT Motor

Back of

Back of

Wall Switch

Wall Switch

Please Note: This Splitter/Jack is located
inside the junction box of your screen.

Internal LVC-IV - Single or Multiple Projection Screen Wiring Diagram

INTERNAL SCREEN WIRING

Green/Yellow

(Motor Ground)

Black (Up)

Brown (Down)

Blue (Common)

N

To

230 VAC

L1

Line

White -Common to screen & 230V AC Neutral

Location of key
operated on-off

switch if furnished.

Green/Yellow (Ground)

Red-to screen (directional)

Brown-to screen (directional)

Yellow-to 230V AC-Hot

Black-to 230V AC-Hot

Dashed wiring by electrician
Low-voltage wiring by others
Factory wiring

External LVC-IV - Single or Multiple Projection Screen Wiring Diagram

Internal Screen Wiring

Blue (Common)

Brown (Down)

Black (Up)

Green/Yellow
(Motor Ground)

To

230 VAC

Line

GND

N

L1

White-Common to screen & 230V AC Neutral

Red-to screen (directional)

Brown-to screen (directional)

Yellow-to 230V AC-Hot

Black-to 230V AC-Hot

Green/Yellow (Ground)

Location of key
operated 0n-off

switch if furnished.

Dashed wiring by electrician
Low-voltage wiring by others

FUSE - 3.15 AMP

FUSE - 3.15 AMP

Receiver
Button

250 VAC 5x20mm

Receiver

Button

250 VAC 5x20mm

OR

Back of

Back of

Wall Switch

Wall Switch

3 Button Wall Switch
DOWN - Black
COM - White
UP - Red

Electrically Straight
Data Cable to more

LVC-IV modules.*

RS232/485
Inputs/Outputs

IR Eye Input

Low-Voltage
Trigger
4-28 VDC

3 Button Wall Switch
DOWN - Black
COM - White
UP - Red

Electrically Straight
Data Cable to more

LVC-IV modules.*

RS232/485

Inputs/Outputs

IR Eye Input

Low-Voltage Trigger

4-28 VDC

*A maximum of six (6)
LVC-IV modules can be
linked together.

*A maximum of six (6)
LVC-IV modules can be
linked together.

Please Note: 5V DC must
be connected to set limits
using the wall switch.

W

Wall Swit