Draper DMSD, 88988 Instructions Manual

INSTRUCTIONS FOR

Combined Stud Detector

& Distance Estimator

Stock No.88988 Part No.DMSD

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE SAFE AND

EFFECTIVE USE OF THIS PRODUCT.

DECLARATION OF CONFORMITY

CONTENTS

Contents/Declaration .................................................................................................................................. 1

Specification/Assembly ................................................................................................................................ 2

Operation and Use ................................................................................................................................... 3-4

Disposal ...................................................................................................................................................... 5

Explanation of Symbols/Pictograms ............................................................................................................. 5

We:
Draper Tools Ltd.,
Hursley Road,
Chandler’s Ford,
Eastleigh, Hampshire.
SO53 1YF.
England.

Declare under our sole responsibility that the product:

Stock No:- 88988.

Part No:- DMSD.

Description:- Distance Measure Stud Detector.

To which this declaration relates is in conformity with the following directive(s)

89/336/EEC

With reference to

SPECIFICATION

The Draper Tools policy of continuous improvement determines the right to change
specification without notice.

Stock No. ......................................................................................................................... 88988

Part No. ............................................................................................................................ DMSD

Detection Distance:

Stud ..................................................................................................................... 19.05mm

Distance ......................................................................................................... 0.60-15.24M

Accuracy ............................................................................................................. ±0.5% ±1 Digit

Resolution .................................................................................................................. 0.01M (1")

Aperture Angle (approx.) ......................................................................................................... 5°

Laser Diode Type ................................................................................................... 650nM Diode

Laser Class ..................................................................................................................... Class 2A

Power Source* .............................................................................................................. 9V (PP3)

Weight .......................................................................................................................... 0.192kg

Operating Temperature ........................................................................... 32°F-104°F (0°C-40°C)

* Draper Stock No.62044

ASSEMBLY

- BATTERY INSTALLATION: (FIG.1)

When the battery power starts getting low a

battery symbol will appear on the display.

Slide out battery door $ located at the rear

of the unit. Connect a new 9V PP3 battery*

FIG.1

$

OPERATION AND USE

- STUD DETECTOR: (FIG.2)

Place the detector flat against the wall. Press

and hold button % to calibrate the unit. The
buzzer will sound to confirm and the display
will read 'Stud'.

NOTE: If by chance, the calibration is carried out

too close or over a stud the detector will never
pick up any readings, and give false
information. For this reason it is advisable to
take a couple of readings and calibrate the unit
in different positions to ensure accuracy.

Upon detection of a stud or nogging the bars

will begin to increase in the LCD display and the
buzzer will sound when all twelve bars are lit.

The best method of accuracy is to mark the wall

at the point where the buzzer has sounded.
Then move the detector approximately 30cm
past this point. Trace back with the detector
again, until the buzzer is sounded. Mark the
wall, and the midway point between the marks
is the centre of the stud/nogging.

NOTE: The wall must be a cavity design for the

detector to work correctly. If the cavity has
been filled with glass fibre, even this may effect
the readout.

- DISTANCE DETECTION: (FIG.3)

Ensure the detector is positioned and pointing

perpendicular to the target area. The laser is a
guide to where the measurement is being

FIG.3

FIG.2

%

1. TO TAKE STANDARD MEASUREMENTS:
Press button ' to take the measurement. The result will be displayed unless an error has

occurred in which case try again.

2. TO ADD RESULTS: (without using the memory)
Press button ' to take the measurement. Press button ( to enter the addition mode.

The '+' is displayed on the LCD. Press button ' again to take the next reading. Press
button ( to display the result.

3. TO ADD RESULTS: (using the memory)
Press button ' to take the measurement. Press button ) to save the current

measurement. Press button ' to to take the next reading. Press button ( to enter the
addition mode. The '+' is displayed on the LCD. Press button * to recall the previous
measurement. Press button ( to display the result.

4. TO TAKE AREA MEASUREMENTS:
Press button + to enter area mode. The symbol will appear on the LCD with the 'L'

flashing. Press button ' to take the length measurement. If the measurement was
successful the 'W' will begin flashing. Press button ' to take the width measurement. If
successful the result in Ft

2/M2

will be displayed under the individual measurement button

' to cycle through the two individual measurements or press button + to begin a new
area measurement. Alternatively, press and hold button ' for two seconds to exit the
area mode.

NOTE: It is possible to store an area result in the memory, take a fresh area measurement

and add them together using button (.

5. TO TAKE VOLUME MEASUREMENTS:
Press button , to enter volume mode. The symbol will appear on the LCD with the 'L'

flashing. Press button ' to take the length measurement. If the measurement was
successful the 'W' will begin flashing. Press button ' to take the width measurement. If
successful the 'H' will begin flashing. Press button ' to take the height measurement. If
successful the result in Ft

3/M3

will be displayed under the individual measurement. Press

button ' to cycle through the three individual measurements or press button , to

OPERATION AND USE

DISPOSAL OF POWER TOOLS

- At the end of the machine‘s working life, or when it can no longer be repaired, ensure that
it is disposed of according to national regulations.

- Contact your local authority for details of collection schemes in your area.

In all circumstances:

• Do not dispose of power tools with domestic waste.

• Do not incinerate.

• Do not abandon in the environment.

• Do not dispose of WEEE* as unsorted municipal waste.

* Waste Electrical & Electronic Equipment.

EXPLANATION OF SYMBOLS/PICTOGRAMS

NOTES

CONTACTS

- DRAPER TOOLS LIMITED,
Hursley Road, Chandler's Ford,

Eastleigh, Hampshire. SO53 1YF. U.K.

- Helpline: [phone]

- Sales Desk: [phone]

- General Enquiries: [phone]

- Service/Warranty Repair Agent
For aftersales servicing or warranty repairs, please

contact the Draper Tools Helpline for details of an
agent in your local area.