OPERATING
INSTRUCTIONS
1. Always wear safety goggles or glasses.
2. Always ensure machine is switched off before connecting to air supply.
3. Disconnect any machine from the air supply before changing blades or
discs, and before servicing any type of machine.
4. Always keep your air tool clean and lubricated. Daily lubrication is essential
to avoid internal corrosion and possible failure.
5. Do not wear watches, rings, bracelets or loose clothing when using air tools.
6. Use only light weight coil hoses from a tool to the wall or compressor
coupling. Do not fit quick change couplings onto the machine as vibration
can cause the coupling to fail.
7. Do not overload the machine. Allow the tool to operate at its optimum speed
for maximum efficiency.
8. Do not increase the air pressure above the manufacturers recommended
level, as excessive overload can cause the machine casing to split.This also
creates excessive wear on moving parts and possible failure.
9. In the interests of safety and possible damage to the machine/operator,
always ensure that the machine has stopped before putting it down after use.
10. Always ensure that the workpiece is firmly secured leaving both hands free
to control the machine.
11. Always ensure that the accessories such as blades, discs, sockets, etc. are
rated/designed for use with the machine and correctly and securely
fastened before connecting the machine to the air supply.
12. When grinding, sanding or cutting always wear an appropriate face mask or
respiratory equipment.
Draper air tools have been carefully tested and inspected before shipment and are
guaranteed to be free from defective materials and workmanship for 6 months from
the date of purchase except where tools are hired out when the guarantee period is
ninety days from the date of purchase.
Should the machine develop any fault, please return the complete tool to your
nearest authorized warranty repair agent or contact Draper Tools Limited,
Chandler’s Ford, Eastleigh,Hampshire, SO53 1YF.England.Telephone (023) 8049 4344.
If, upon inspection it is found that the fault occurring is due to defective materials or
workmanship,repairs will be carried out free of charge. This guarantee does not
apply to normal wear and tear, nor does it cover any damage caused by misuse,
careless or unsafe handling, alterations, accident, or repairs attempted or made by
any persons other than the authorized Draper warranty repair agent.
This guarantee applies in lieu of any other guarantee expressed or implied and
variation of its terms are not authorized.
Your Draper guarantee is not effective unless you can produce upon request a dated
receipt or invoice to verify your proof of purchase within the guarantee period.
Please note that this guarantee is an additional benefit and does not affect your
statutory rights.
AIR UNDERBODY COATING GUN
STOCK No.55109 PART No.4244A
Cannister cap thread (schultz type)...................M42x3P
Tube length........................................................250mm
Operating air pressure ...........................90psi (6.2 bar)
Average air pressure...........................8cfm (227 L/min)
Minimum hose size ....................................................3⁄8"
Air inlet size ........................................................1⁄4" BSP
Sound pressure level ..........................................81 dbA
Sound power level..............................................93 dbA
WEAR EAR PROTECTION
PROBLEMS POSSIBLE CAUSES REMEDIES
Tool runs at normal speed but loses ■ Motor parts worn. ■ Lubricating clutch housing.
under load
■ Cam clutch worn or sticking due to lack of ■ Check for excess clutch oil. Clutch cases need only be half full. Overfilling
lubricant. can cause drag on high speed clutch parts, e.g. a typical oiled/lubricated wrench
requires 1⁄2 ounce of oil.
GREASE LUBRICATED:NOTE: Heat usually indicates insufficient grease in
chamber. Severe operating conditions may require more frequent lubrication.
Tool runs slowly.Air flows slightly from exhaust ■ Motor parts jammed with dirt particles ■ Check air inlet filter for blockage.
■ Power regulator in closed position ■ Pour air tool lubricating oil into air inlet as per instructions.
■ Air flow blocked by dirt. ■ Operate tool in short bursts quickly reversing rotation back and forth where applicable.
■ Repeat above as needed. If this fails return to service centre.
Tools will not run. Air flows freely from exhaust ■ One or more motor vanes stuck due to material ■ Pour air tool lubricating tool into air inlet.
build up. ■ Operate tool in short bursts of forward and/or reverse rotation where applicable.
■ Tap motor housing gently with plastic mallet.
■ Disconnect supply. Free motor by rotating drive shank manually where applicable
■ If tool remains jammed return to service centre.
Tool will not shut off ■ ‘O’ rings throttle valve dislodged from seat ■ Replace ‘O’ ring or return to service centre.
inlet valve.
Note: Repairs should only be carried out by a qualified person.
DRAPER HELPLINE (023) 8049 4344.
SAFETY RULES FOR
AIR TOOL PRODUCTS
SPECIFICATION
DECLARATION OF
CONFORMITY
AIR TOOLS
GUARANTEE
TROUBLE
SHOOTING
AIR SUPPLY:
Tools in the Draper range generally operate at a maximum pressure of 90 psi (see
speci-fications) and this should be controlled via a combined regulator/oil/water
separator such as the Draper 4222/3 or 4222/4 units which with proper maintenance
will ensure a constant supply of dry air and lubricating oil at all times. See Fig. 1. below.
Always check machine operating pressure before use.
Water in the compressor tank will cause serious corrosion to your air tools and should
be drained daily to avoid excessive water in your air supply. Dirty wet air rapidly
shortens the life of your air tool.
If you are using an air tool on a hose over 25ft. long it is advisable to increase the bore
of the hose to the next larger size available ie.
1
⁄4
" increases
3
⁄8
". This will ensure
adequate pressure and volume of air to power the machine.
RECOMMENDED AIR SUPPL
Y:
OPERATION:
Some air tools have inbuilt regulators which can be used to control speed/torque
performance, on machines without inbuilt regulators this can be done by varying the
pressure on your air supply regulator.
MAINTEN
ANCE:
Every day, before use, remove the tool from the air line, use an oil can and pour the
equivalent of a tablespoon of suitable oil into the machine (through the air intake).
Operate at low speed to ensure lubrication of all moving parts. If machine is in constant
use or is to be used for long periods of time a combination filter/lubricator must be
fitted in the system. At all times the system must be fitted with an air filter.
Recommended oils are Shell Tellus 22, Duckhams Zircon 32 or Castrol AWS32. Do
not
use normal engine oil or similar.
Please note: failure to comply with the above Maintenance/Operating
Instructions could invalidate the Guarantee.
We Draper Tools Ltd. Declare under our sole
responsibility that the product:
Stock Number:- 55109 Part Number:- 4244A
Description:- Air underbody coating gun
To which this declaration relates is in conformity with
the following directive(s):-
89/392/EEC, 91/368/EEC and 93/44/EEC.
With reference to TC255N, EN292, EN28662/1 and
Pneurop Standard 8N-1.
JOHN DRAPER
Managing Director 05/98
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE SAFE AND
EFFECTIVE USE OF THIS TOOL.
02/2001
Loading...