Installation/Operating Instructions
Baronet Electric Projection Screen by Draper
Caution
➀ Read instructions through completely before proceeding; keep them for
future reference. Follow instructions carefully. Installation con trary to
instructions in val i dates warranty. Care in mounting and correct operation will mean long and satisfactory service from your screen.
➁ Screen should be accessible for complete removal should fabric be-
come damaged or should other ser vice be required.
➂ Screen should be installed level (using a carpenter’s level).
➃ Nothing should be fastened to screen dowel or viewing surface.
➄ Screen operates on 110-120V, 60 Hz. or 220-230V 50 Hz. current,
de pend ing on model ordered.
NOTE: Screen has been thoroughly inspected and tested at factory and
found to be operating properly prior to shipment.
Hanging Screen
General:
When locating view ing surface and checking clear ance for screen’s op er a tion,
remember surface is centered in case. Handle case care ful ly to pro tect fi nish.
Regardless of mounting method, screen should be positively and securely
sup port ed so that vibration or even abusive pulling on the viewing surface will
not cause case to work loose or fall. Installer must insure that fas ten ers used
are of adequate strength and suit able for mounting sur face cho sen.
Suspended Installation:
Suspend screens from holes in top of endcaps as shown. S-hooks, chains (or
cable) and turn buck les should be pro vid ed by installer. “S” hooks should go
through the front holes on the endcaps (see drawing below), and both ends
of the “S” hooks should be crimped for additional safety. Chains should be at tached to beams or other struc tur al mem bers. Turn buck les should be adjusted
so screen hangs level.
Wall Installation:
Mount screen through holes in back of endcaps as shown. Installer should
furnish appropriate hardware as required.
Recessed Installation:
Recess should permit access for removal of screen if necessary. Screen may
be mounted using angles (by others), or by utilizing steps for wall or suspended installation. Angles should be at tached to beams or other struc tur al
mem bers.
Back hole for wall mounting.
Hardware by others.
Mounting angle
and hardware
by others.
Suggested for
recessed
installations.
Minimum 5 cm wide
slot for passage of
viewing surface if
suspended above ceiling
Crimp
Crimp
Top Hole for
suspended mounting.
Hardware by others.
Example of
suspension
above ceiling.
Ceiling tile
and grid
(by others)
®
Case Dimensions
3¼"
(83
Fabric width + 5¾" (146 mm)
mm)
3¾"
(96 mm)
3¼"
(83 mm)
Viewing
Surface
Electrical Connections
110-120V Model:
Screen operates on 110-120V 60 hz. current. Screen shipped with internal wiring complete. No external wiring needed. Plug cord into standard
110-120V AC outlet. Duty cycle: On 26 seconds/Off 3 minutes.
All operating switches should be “OFF” before power is connected.
220-230V Model:
Screen operates on 220-230V 50 hz. current. Screen is shipped with internal
wiring complete. Power cord leads need to be wired to 220V power supply
or to an appropriate plug (not provided) and then plugged into standard 220230V AC outlet. See diagram below for wire colors.
Blue or White = Neutral
Brown or Black = Line
Green = Ground
All operating switches should be “OFF” before power is connected.
Please Note: If you remove the plug and hardwire this unit, do not wire in
parallel with other motors.
Operation
Before operating screen, remove tape securing fabric and dowel to case.
Screen dowel will initially be hanging about 1½" (5 cm) out of the case.
Screen is equipped with a 3-position operating switch, located on the power
cord. To lower the screen, move switch down. Screen will stop automatically when lower limit switch is reached. To raise the screen, move switch
up. Again, the screen will stop automatically when the upper limit switch is
reached. The screen may be stopped in any intermediate position by moving
the switch to the center “off” position during operation.
Adjustments
Please Note: Screen limits are factory set for optimum performance of the
screen. Any adjustment of these limits could void the warranty. Please
check with Draper prior to resetting screen limits.
CAUTION: Always be prepared to shut screen off manually when new
adjustment is being tested. Screen may be severely damaged if viewing
surface is allowed to run too far up or too far down.
CAUTION: Be sure all switches are in “off” position before ad just ing limit
switches.
“Down” limit switch: Down stopping position can be adjusted by turning
white knob with a screw driver or hex wrench. Turning knob counterclockwise
will allow viewing surface to run farther down. Turning it clockwise will reduce
the amount of exposed viewing surface.
“Up” limit switch: Up stopping position can be adjusted by turning red knob
with a screw driver or hex wrench through the small grommet. Turning knob
counterclockwise will allow surface to run farther into screen case. Turning it
clockwise will allow viewing surface to stop farther out of screen case.
Copyright © 2011 Draper Inc. Form Baronet_Inst11 Printed in U.S.A.
If you encounter any diffi culties installing or ser vic ing your Baronet screen, call your
dealer or contact Draper, Inc., Spiceland, In di ana, 765-987-7999; or fax 765-987-1689.
Loading...