Draper 121226 Instructions

Receiv

White-Common to screen & 110 VAC Neutral

Red-to screen (directional)

Brown-to screen (directional)

Ye llow-to 110 VAC-Hot

Black-to 110 VAC-Hot

Green/Yellow (Ground)

White (Common)

Red (Up)

Black (Down)

Internal Screen Wiring

Green/Yellow

(Motor Ground)

Signal Light

IR Eye Input

Low Voltage

Tr igger

3-28 VDC

RS232/485

Inputs/Outputs

Wiring Instructions

Radio Frequency Remote Control by Draper

Wiring Diagram for LVC-IV with Radio Frequency Remote Control

White-Neutral (Common) to screen & 110V-120V AC
Red-to screen (directional)
Brown-to screen (directional)
Yellow-to 110V-120V AC
Black-to 110V-120V AC

250 VAC 5x20mm

FUSE - 3.15 AMP

Green-Ground

Electrically Straight

Data Cable

Dashed wiring by electrician

LVC-IV

Signal Light

RF Transmitter

Operating range is 250 ft (open distance). Each time
the RF signal penetrates a wall, distance will fall off 50%.

Wire to connect power to LVC-IV should be between 18 AWG and 12 AWG (solid or stranded) 2 conductors with ground. Wire size needs to be sufficient to
carry the motor load. Red and Black wires are the “open” and “close” leads from the motor. The LVC-IV comes enclosed in a metal box conforming to the Nation­al Electric Code (NEC).

Radio Frequency (RF) Remote Control

The LVC-IV comes with built-in Radio Frequency Remote control capability (optional handheld transmitter NOT included).

To "Learn" a remote

1 Press receiver button on LVC-IV (see Fig. 2A).
2 Signal light will flash slowly.
3 Press transmitter's Up button within 10 seconds (see Fig. 2B).
4 Signal light flashes three times quickly.

To "Un-Learn" a remote

1 Press receiver button on LVC-IV (see Fig. 2A).
2 Signal light will flash slowly.
3 Press transmitter's Down button within 10 seconds (see Fig. 2C).
4 Signal light flashes three times quickly.

Signal
Light

Button

er

Receiver
Button

To "Un-Learn" all remotes

1 Press receiver button on LVC-IV until signal light flashes quickly, then release.
2 Press receiver button once while signal light is flashing.
3 Signal light will stop flashing.

Please Note: If you are experiencing issues with RF signal strength, the RF antenna can be threaded out one of the knockouts for better reception.

Figure 2

BA

C

Copyright ©2015 Draper Inc. Form RFRemoteControl_Wiring15 Printed in U.S.A.

If you encounter any difficulties installing/wiring your RF Remote Control, call
your dealer or Draper, Inc., Spiceland, Ind., [phone]; fax [phone].

Receiv

White-Common to screen & 110 VAC Neutral

Red-to screen (directional)

Brown-to screen (directional)

Ye llow-to 110 VAC-Hot

Black-to 110 VAC-Hot

Green/Yellow (Ground)

White (Common)

Red (Up)

Black (Down)

Internal Screen Wiring

Green/Yellow

(Motor Ground)

Signal Light

230V Radio Frequency Remote Control by Draper

IR Eye Input

Low Voltage

Tr igger

3-28 VDC

RS232/485

Inputs/Outputs

Wiring Instructions

Wiring Diagram for LVC-IV with Radio Frequency Remote Control

White-Neutral (Common) to screen & 230V AC
Red-to screen (directional)
Brown-to screen (directional)
Yellow-to 230V AC
Black-to 230V AC

250 VAC 5x20mm

FUSE - 3.15 AMP

Green-Ground

The LVC-IV comes with built-in Radio Frequency Remote control capability (optional handheld transmitter NOT included).

To "Learn" a remote

1 Press receiver button on LVC-IV (see Fig. 2A).
2 Signal light will flash slowly.
3 Press transmitter's Up button within 10 seconds (see Fig. 2B).
4 Signal light flashes three times quickly.

To "Un-Learn" a remote

1 Press receiver button on LVC-IV (see Fig. 2A).
2 Signal light will flash slowly.
3 Press transmitter's Down button within 10 seconds (see Fig. 2C).
4 Signal light flashes three times quickly.

Electrically Straight

Data Cable

Dashed wiring by electrician

LVC-IV

Signal Light

RF Transmitter

Operating range is 76 meters (open distance). Each time
the RF signal penetrates a wall, distance will fall off 50%.

Wire to connect power to LVC-IV should be between 18 AWG and 12 AWG (solid or stranded) 2 conductors with ground. Wire size needs to be sufficient to
carry the motor load. Red and Black wires are the “open” and “close” leads from the motor. The LVC-IV comes enclosed in a metal box conforming to the Nation­al Electric Code (NEC).

Radio Frequency (RF) Remote Control

Signal
Light

Button

er

Receiver
Button

To "Un-Learn" all remotes

1 Press receiver button on LVC-IV until signal light flashes quickly, then release.
2 Press receiver button once while signal light is flashing.
3 Signal light will stop flashing.

Please Note: If you are experiencing issues with RF signal strength, the RF antenna can be threaded out one of the knockouts for better reception.

Figure 2

CBA

Copyright ©2015 Draper Inc. Form RFRemoteControl_230V_Wiring15 Printed in U.S.A.

If you encounter any difficulties installing/wiring your RF Remote Control, call
your dealer or Draper, Inc., Spiceland, Ind., [phone]; fax [phone].