Page 1
Projection Viewing Surface Care & Maintenance Instructions
Please Note: Cleaning should be undertaken only when needed and with great care. Not all stains can be removed. Please take care to protect
your screen from damage to minimize the need for these procedures.
OptiView™
Matt White XT1000E, Contrast Grey XH800E, Contrast White XH1100E
Clean surface with warm water. A solution of mild dishwashing liquid diluted with warm water can also be used. Using a soft, disposable cloth, gently wipe
the surface, completely rinse the entire surface with clear water and blot dry. Do not allow any cleaner to be absorbed by the fabric. Do not use clean ing solvents
or abrasives. Do not use Armor All
Glass Beaded CH3200E
Clean with a very soft brush or cloth and care ful ly dust the surface. Do not use soap, water, solvents or abrasives. Do not use Armor All®. These substances
will damage a glass beaded viewing surface.
High Performance XS850E
Clean surface with a soft, non abrasive cloth, wiping gently in a horizontal motion across the screen. If dry cloth does not work, soak cloth in warm water
(less than 105° F/40°C) and squeeze until cloth is only damp (not dripping water). Gently wipe screen surface in a horizontal motion. If cloth soaked in warm water does not work then take damp cloth and apply a small amount of a mild soap or detergent. Gently rub several times in a horizontal motion over the affected
area several times. Rinse soap out of cloth and squeeze until cloth is only damp. Gently wipe away soap or mild detergent. Perform this step until visible signs of
cleaning agent are no longer seen. Do not use alcohol, acetone, organic solvents, alkaline-based cleaners or acidic-based cleaners.
Pearl White CH1900E, Argent White XH1500E, Radiant CT2900E, Contrast Radiant CH2700E
Using a clean, white cloth (100% cotton preferred) that is dampened with clear water, gently wipe the area in one direction. Do not use a circular motion.
To clean a stubborn stain or a sticky surface, a solution of mild dishwashing liquid diluted with warm water can also be used following the same procedure
as for water, and allow it to air dry.
®
.
Ecomatt XT700E
Blow off excess debris with air or use a feather duster, or using a clean, white cloth (100% cotton preferred) that is dampened with clear water, gently wipe
the area in one direction.
OptiFlex™
Matt White XT1000V, Grey XH600V
Clean surface with warm water. A solution of mild dishwashing liquid diluted with warm water can also be used. Using a soft, disposable cloth, gently wipe
the surface, completely rinse the entire surface with clear water and blot dry. Do not allow any cleaner to be absorbed by the fabric. Do not use cleaners which
contain abrasives or wax. Do not use Armor All
®
.
Pearl White CH1900V
Clean with a very soft brush or cloth and care ful ly dust the surface. Do not use soap, water, solvents or abrasives. Do not use Armor All®.
ClearSound™
Grey Weave XH600E, NanoPerf XT800V, Perf XT900V, Perf XT950E, White Weave XT900E
Clean surface with warm water. A solution of mild dishwashing liquid diluted with warm water can also be used. Using a soft, disposable cloth, gently wipe
the surface, completely rinse the entire surface with clear water and blot dry. Do not allow any cleaner to be absorbed by the fabric. Do not use clean ing solvents
or abrasives. Do not use Armor All
®
.
CineFlex™
CineFlex Dual XT600V, CineFlex MH800V, CineFlex CH1200V
Gently clean this rear projection material with warm water. A solution of mild dishwashing liquid diluted with warm water can also be used. Using a soft,
disposable cloth, gently wipe the surface, completely rinse the entire surface with clear water and blot dry. Do not allow any cleaner to be absorbed by the fabric.
Do not use cleaners which contain abrasives or wax. Do not use Armor All
®
.
Rigid Rear Screens
IRUS, Cinescreen®, DiamondScreen
Rigid rear screens can be cleaned with a soft, lint free cloth to remove dust from the surface. Remove soil marks with a cloth or sponge and mild soapy
water. Wring free of excess moisture before applying, rinse and blot dry. Do not use solvent or abra sives. Do not use Armor All
™
®
.
®
These are basic cleaning tips for dust or dirt. For more
information on cleaning stains, please contact Draper, Inc.
Cinescreen® is a reg is tered trademark of Draper, Inc.
®
Copyright © 2012 Draper Inc. Form Care&Maintenance_Inst12 Printed in U.S.A.
Armor All
is a registered trademark of Armor All Products Corporation
Loading...