Draco 3514-7R Operating Instructions Manual

20.11.2015 Specifications are subject to change for improvement without prior notice.

Operating instructions

1. Intended use. This Power Tool is intended for

industrial applications, for cutting sheet metal (maximum capacity is indicated in the Specifications), for use with cutting jaws and cutting blades which are indicated in these operating instructions or recommended by DRÄCO.

2. Do NOT cut sheet metal along welding points. Do NOT cut multi layer sheets, which exceed the maximum cutting capacity.

3. Switching ON/OFF the power tool. First check cable and plug for damage. Slide the switch pad (5) BACKWARD for switching ON the power tool. Slide the switch pad (5) FORWARD for switching OFF the power tool.

4. For inside cutting, the shortest curve possible has a radius of 45 mm (±1¾”). If cutting a radius with the right hand, cut from right to left. The outside radius is unlimited.

5. For cutting out curved or circular inside patterns, a 14 mm (± 1/2 “) hole, or a punched slot should be made to insert the centre cutter.

6. If after cutting, a small strip remains this can easily be trimmed off to the exact measurement, without leaving a burr or any distortion of the material. Just one side of the power tools can be used for cutting also (e.g. along a marked line). Lift the power tools out of the shavings while the motor is running. Cut off longer shavings.

7. Both knife and jaws can be sharpened. After being sharpened or replaced, the knife at it’s lowest point should protrude the jaws by approximately 3 mm. The knife should have approximately 0,05 mm (0,005”) play on each side of the jaws, centring the cutter with spacing shims supplied.

8. Every 200 operating ours have the cutting blade and cutting jaws sharpened at a specialist workshop.

9. Ensure that the material to be cut is free of oil

and grease.

Care and Maintenance

Warranty

Before working on machine disconnect from power supply by removing plug from socket. Always keep the machine and the ventilation slots clean. Oil the knife pin and knife at regular intervals. If the machine should happen to fail despite the care taken in manufacture and testing, repair should be carried out by an authorised customer services agent for DRÄCO power tools

DRÄCO tools carry a guarantee of 12 months from date of delivery. Damage attributable to normal wear and tear, overload or improper handling will be excluded from the guarantee. (e.g. blades/knifes and jaws) In case of complaint please send the machine, undismantled, to your dealer or the DRÄCO Service Center for electric power tools.

Environmental protection

CE-Declaration of conformity

Recycling raw materials instead of waste

disposal

Machine, accessories and packaging should be sorted for environment-friendly recycling. These instructions are printed on recycling paper manufactured without chlorine

We declare under our sole responsibility that this product is in conformity with the following standards. EC 98/37, EC 93/ 68 EWG, EC 04/108 EC, or standardisation documents DIN EN ISO 12100-1, DIN EN ISO 12100-2, EN 50 144, EN 55 014

09 Susanne Draenert

Operating Instructions for the Radius-Seam Metal Shear 3514-7R

To avoid any disturbance please read the following instructions:

For your safety:

1 2 3 4 5

1 Safe operation of this machine is possible only when the operating instructions and the safety precautions are read completely and the instructions contained therein are strictly observed.

2 The machine must not be used in a wet environment.

3 Always inspect cable and plug before using machine.

Only have damage repaired by a qualified professional. Put the plug into the mains socket only when the machine is switched off.

4+5 Always wears protective goggles, protective gloves and heavy-duty shoes when working.

Do not carry the machine by the cable.

Always remove the plug from the power supply socket before carrying out any work on the machine, when interrupting work and when not using the machine.

Always place the cable to the rear away from the machine.

Apply the machine to the sheet metal only when switched on.

Always provide for secure footing when working.

Firmly clamp the work piece if it does not remain stationary from its own weight.

The knife should not rub on the jaws: Possible danger of cutting tool breakage.

Do not exceed the maximum allowable material thickness especially when cutting over double folded joints or welded seams.

For further notes on safety refer to enclosed sheet

DRÄCO Radius Seam Metal Shear

type

3514-7R

max. cutting capacity

Art.no.

61080

spare parts

steel

400 N/mm²

mm/ga.

2,0 / 14

knife

371401

stainless steel

600 N/mm²

mm/ga.

1,5 / 16

set of jaws

BG37222

stainless steel

800 N/mm²

mm/ga.

1,3 / 18

knife-pin set

BG35055

aluminium

250 N/mm²

mm/ga.

3,0 / 10

duct- & Pittsburgh Seam

400 N/mm²

mm/ga.

4 x 0,75 / 21

optional accessories

tightest radius

mm/ “

45 / 1¾

metal-box

18000

working speed ±

m/min

5-7

strokes

min

-1

2400

motor capacity

Watts

500

weight

kg2starting hole

Ø mm

0óI

spiral ducting starting hole 12-14 mm Ø

accurate cutting along a marked line

20.11.2015 Specifications are subject to change for improvement without prior notice.

Operating instructions

1. Intended use. This Power Tool is intended for

2. Do NOT cut sheet metal along welding points. Do

NOT cut multi layer sheets, which exceed the maximum cutting capacity.

3. Switching ON/OFF the power tool. First check

cable and plug for damage. Slide the switch pad (5) BACKWARD for switching ON the power tool. Slide the switch pad (5) FORWARD for switching OFF the power tool.

4. For inside cutting, the shortest curve possible has

a radius of 45 mm (±1¾”). If cutting a radius with the right hand, cut from right to left. The outside radius is unlimited.

5. For cutting out curved or circular inside patterns,

a 14 mm (± 1/2 “) hole, or a punched slot should be made to insert the centre cutter.

6. If after cutting, a small strip remains this can

easily be trimmed off to the exact measurement, without leaving a burr or any distortion of the material. Just one side of the power tools can be used for cutting also (e.g. along a marked line). Lift the power tools out of the shavings while the motor is running. Cut off longer shavings.

7. Both knife and jaws can be sharpened. After

being sharpened or replaced, the knife at it’s lowest point should protrude the jaws by approximately 3 mm. The knife should have approximately 0,05 mm (0,005”) play on each side of the jaws, centring the cutter with spacing shims supplied.

8. Every 200 operating ours have the cutting blade

and cutting jaws sharpened at a specialist workshop.

9. Ensure that the material to be cut is free of oil

and grease.

Care and Maintenance

Warranty

Environmental protection

CE-Declaration of conformity

Recycling raw materials instead of waste

disposal

Machine, accessories and packaging should be sorted for environment-friendly recycling. These instructions are printed on recycling paper manufactured without chlorine

09 Susanne Draenert

Operating Instructions for the Radius-Seam Metal Shear 3514-7R

To avoid any disturbance please read the following instructions:

For your safety:

1 2 3 4 5

1 Safe operation of this machine is possible only when the operating instructions and the safety precautions are read completely and the instructions contained therein are strictly observed.

2 The machine must not be used in a wet environment.

3 Always inspect cable and plug before using machine.

Only have damage repaired by a qualified professional. Put the plug into the mains socket only when the machine is switched off.

4+5 Always wears protective goggles, protective gloves and heavy-duty shoes when working.

Do not carry the machine by the cable.

Always remove the plug from the power supply socket before carrying out any work on the machine, when interrupting work and when not using the machine.

Always place the cable to the rear away from the machine.

Apply the machine to the sheet metal only when switched on.

Always provide for secure footing when working.

Firmly clamp the work piece if it does not remain stationary from its own weight.

The knife should not rub on the jaws: Possible danger of cutting tool breakage.

Do not exceed the maximum allowable material thickness especially when cutting over double folded joints or welded seams.

For further notes on safety refer to enclosed sheet

DRÄCO Radius Seam Metal Shear

type

3514-7R

max. cutting capacity

Art.no.

61080

spare parts

steel

400 N/mm²

mm/ga.

2,0 / 14

knife

371401

stainless steel

600 N/mm²

mm/ga.

1,5 / 16

set of jaws

BG37222

stainless steel

800 N/mm²

mm/ga.

1,3 / 18

knife-pin set

BG35055

aluminium

250 N/mm²

mm/ga.

3,0 / 10

duct- & Pittsburgh Seam

400 N/mm²

mm/ga.

4 x 0,75 / 21

optional accessories

tightest radius

mm/ “

45 / 1¾

metal-box

18000

working speed ±

m/min

5-7

strokes

min

-1

2400

motor capacity

Watts

500

weight

kg2starting hole

Ø mm

0óI

spiral ducting starting hole 12-14 mm Ø

accurate cutting along a marked line

20.11.2015 Specifications are subject to change for improvement without prior notice.

Operating instructions

1. Intended use. This Power Tool is intended for

2. Do NOT cut sheet metal along welding points. Do

NOT cut multi layer sheets, which exceed the maximum cutting capacity.

3. Switching ON/OFF the power tool. First check

cable and plug for damage. Slide the switch pad (5) BACKWARD for switching ON the power tool. Slide the switch pad (5) FORWARD for switching OFF the power tool.

4. For inside cutting, the shortest curve possible has

a radius of 45 mm (±1¾”). If cutting a radius with the right hand, cut from right to left. The outside radius is unlimited.

5. For cutting out curved or circular inside patterns,

a 14 mm (± 1/2 “) hole, or a punched slot should be made to insert the centre cutter.

6. If after cutting, a small strip remains this can

7. Both knife and jaws can be sharpened. After

8. Every 200 operating ours have the cutting blade

and cutting jaws sharpened at a specialist workshop.

9. Ensure that the material to be cut is free of oil

and grease.

Care and Maintenance

Warranty

Environmental protection

CE-Declaration of conformity

Recycling raw materials instead of waste

disposal

Machine, accessories and packaging should be sorted for environment-friendly recycling. These instructions are printed on recycling paper manufactured without chlorine

09 Susanne Draenert

Operating Instructions for the Radius-Seam Metal Shear 3514-7R

To avoid any disturbance please read the following instructions:

For your safety:

1 2 3 4 5

1 Safe operation of this machine is possible only when the operating instructions and the safety precautions are read completely and the instructions contained therein are strictly observed.

2 The machine must not be used in a wet environment.

3 Always inspect cable and plug before using machine.

Only have damage repaired by a qualified professional. Put the plug into the mains socket only when the machine is switched off.

4+5 Always wears protective goggles, protective gloves and heavy-duty shoes when working.

Do not carry the machine by the cable.

Always remove the plug from the power supply socket before carrying out any work on the machine, when interrupting work and when not using the machine.

Always place the cable to the rear away from the machine.

Apply the machine to the sheet metal only when switched on.

Always provide for secure footing when working.

Firmly clamp the work piece if it does not remain stationary from its own weight.

The knife should not rub on the jaws: Possible danger of cutting tool breakage.

Do not exceed the maximum allowable material thickness especially when cutting over double folded joints or welded seams.

For further notes on safety refer to enclosed sheet

DRÄCO Radius Seam Metal Shear

type

3514-7R

max. cutting capacity

Art.no.

61080

spare parts

steel

400 N/mm²

mm/ga.

2,0 / 14

knife

371401

stainless steel

600 N/mm²

mm/ga.

1,5 / 16

set of jaws

BG37222

stainless steel

800 N/mm²

mm/ga.

1,3 / 18

knife-pin set

BG35055

aluminium

250 N/mm²

mm/ga.

3,0 / 10

duct- & Pittsburgh Seam

400 N/mm²

mm/ga.

4 x 0,75 / 21

optional accessories

tightest radius

mm/ “

45 / 1¾

metal-box

18000

working speed ±

m/min

5-7

strokes

min

-1

2400

motor capacity

Watts

500

weight

kg2starting hole

Ø mm

0óI

spiral ducting starting hole 12-14 mm Ø

accurate cutting along a marked line

20.11.2015 Specifications are subject to change for improvement without prior notice.

Operating instructions

1. Intended use. This Power Tool is intended for

2. Do NOT cut sheet metal along welding points. Do

NOT cut multi layer sheets, which exceed the maximum cutting capacity.

3. Switching ON/OFF the power tool. First check

cable and plug for damage. Slide the switch pad (5) BACKWARD for switching ON the power tool. Slide the switch pad (5) FORWARD for switching OFF the power tool.

4. For inside cutting, the shortest curve possible has

a radius of 45 mm (±1¾”). If cutting a radius with the right hand, cut from right to left. The outside radius is unlimited.

5. For cutting out curved or circular inside patterns,

a 14 mm (± 1/2 “) hole, or a punched slot should be made to insert the centre cutter.

6. If after cutting, a small strip remains this can

7. Both knife and jaws can be sharpened. After

8. Every 200 operating ours have the cutting blade

and cutting jaws sharpened at a specialist workshop.

9. Ensure that the material to be cut is free of oil

and grease.

Care and Maintenance

Warranty

Environmental protection

CE-Declaration of conformity

Recycling raw materials instead of waste

disposal

Machine, accessories and packaging should be sorted for environment-friendly recycling. These instructions are printed on recycling paper manufactured without chlorine

09 Susanne Draenert

Operating Instructions for the Radius-Seam Metal Shear 3514-7R

To avoid any disturbance please read the following instructions:

For your safety:

1 2 3 4 5

1 Safe operation of this machine is possible only when the operating instructions and the safety precautions are read completely and the instructions contained therein are strictly observed.

2 The machine must not be used in a wet environment.

3 Always inspect cable and plug before using machine.

Only have damage repaired by a qualified professional. Put the plug into the mains socket only when the machine is switched off.

4+5 Always wears protective goggles, protective gloves and heavy-duty shoes when working.

Do not carry the machine by the cable.

Always remove the plug from the power supply socket before carrying out any work on the machine, when interrupting work and when not using the machine.

Always place the cable to the rear away from the machine.

Apply the machine to the sheet metal only when switched on.

Always provide for secure footing when working.

Firmly clamp the work piece if it does not remain stationary from its own weight.

The knife should not rub on the jaws: Possible danger of cutting tool breakage.

Do not exceed the maximum allowable material thickness especially when cutting over double folded joints or welded seams.

For further notes on safety refer to enclosed sheet

DRÄCO Radius Seam Metal Shear

type

3514-7R

max. cutting capacity

Art.no.

61080

spare parts

steel

400 N/mm²

mm/ga.

2,0 / 14

knife

371401

stainless steel

600 N/mm²

mm/ga.

1,5 / 16

set of jaws

BG37222

stainless steel

800 N/mm²

mm/ga.

1,3 / 18

knife-pin set

BG35055

aluminium

250 N/mm²

mm/ga.

3,0 / 10

duct- & Pittsburgh Seam

400 N/mm²

mm/ga.

4 x 0,75 / 21

optional accessories

tightest radius

mm/ “

45 / 1¾

metal-box

18000

working speed ±

m/min

5-7

strokes

min

-1

2400

motor capacity

Watts

500

weight

kg2starting hole

Ø mm

0óI

spiral ducting starting hole 12-14 mm Ø

accurate cutting along a marked line

20.11.2015 Specifications are subject to change for improvement without prior notice.

Operating instructions

1. Intended use. This Power Tool is intended for

2. Do NOT cut sheet metal along welding points. Do

NOT cut multi layer sheets, which exceed the maximum cutting capacity.

3. Switching ON/OFF the power tool. First check

cable and plug for damage. Slide the switch pad (5) BACKWARD for switching ON the power tool. Slide the switch pad (5) FORWARD for switching OFF the power tool.

4. For inside cutting, the shortest curve possible has

a radius of 45 mm (±1¾”). If cutting a radius with the right hand, cut from right to left. The outside radius is unlimited.

5. For cutting out curved or circular inside patterns,

a 14 mm (± 1/2 “) hole, or a punched slot should be made to insert the centre cutter.

6. If after cutting, a small strip remains this can

7. Both knife and jaws can be sharpened. After

8. Every 200 operating ours have the cutting blade

and cutting jaws sharpened at a specialist workshop.

9. Ensure that the material to be cut is free of oil

and grease.

Care and Maintenance

Warranty

Environmental protection

CE-Declaration of conformity

Recycling raw materials instead of waste

disposal

Machine, accessories and packaging should be sorted for environment-friendly recycling. These instructions are printed on recycling paper manufactured without chlorine

09 Susanne Draenert

Operating Instructions for the Radius-Seam Metal Shear 3514-7R

To avoid any disturbance please read the following instructions:

For your safety:

1 2 3 4 5

1 Safe operation of this machine is possible only when the operating instructions and the safety precautions are read completely and the instructions contained therein are strictly observed.

2 The machine must not be used in a wet environment.

3 Always inspect cable and plug before using machine.

Only have damage repaired by a qualified professional. Put the plug into the mains socket only when the machine is switched off.

4+5 Always wears protective goggles, protective gloves and heavy-duty shoes when working.

Do not carry the machine by the cable.

Always remove the plug from the power supply socket before carrying out any work on the machine, when interrupting work and when not using the machine.

Always place the cable to the rear away from the machine.

Apply the machine to the sheet metal only when switched on.

Always provide for secure footing when working.

Firmly clamp the work piece if it does not remain stationary from its own weight.

The knife should not rub on the jaws: Possible danger of cutting tool breakage.

Do not exceed the maximum allowable material thickness especially when cutting over double folded joints or welded seams.

For further notes on safety refer to enclosed sheet

DRÄCO Radius Seam Metal Shear

type

3514-7R

max. cutting capacity

Art.no.

61080

spare parts

steel

400 N/mm²

mm/ga.

2,0 / 14

knife

371401

stainless steel

600 N/mm²

mm/ga.

1,5 / 16

set of jaws

BG37222

stainless steel

800 N/mm²

mm/ga.

1,3 / 18

knife-pin set

BG35055

aluminium

250 N/mm²

mm/ga.

3,0 / 10

duct- & Pittsburgh Seam

400 N/mm²

mm/ga.

4 x 0,75 / 21

optional accessories

tightest radius

mm/ “

45 / 1¾

metal-box

18000

working speed ±

m/min

5-7

strokes

min

-1

2400

motor capacity

Watts

500

weight

kg2starting hole

Ø mm

0óI

spiral ducting starting hole 12-14 mm Ø

accurate cutting along a marked line

20.11.2015 Specifications are subject to change for improvement without prior notice.

Operating instructions

1. Intended use. This Power Tool is intended for

2. Do NOT cut sheet metal along welding points. Do

NOT cut multi layer sheets, which exceed the maximum cutting capacity.

3. Switching ON/OFF the power tool. First check

cable and plug for damage. Slide the switch pad (5) BACKWARD for switching ON the power tool. Slide the switch pad (5) FORWARD for switching OFF the power tool.

4. For inside cutting, the shortest curve possible has

a radius of 45 mm (±1¾”). If cutting a radius with the right hand, cut from right to left. The outside radius is unlimited.

5. For cutting out curved or circular inside patterns,

a 14 mm (± 1/2 “) hole, or a punched slot should be made to insert the centre cutter.

6. If after cutting, a small strip remains this can

7. Both knife and jaws can be sharpened. After

8. Every 200 operating ours have the cutting blade

and cutting jaws sharpened at a specialist workshop.

9. Ensure that the material to be cut is free of oil

and grease.

Care and Maintenance

Warranty

Environmental protection

CE-Declaration of conformity

Recycling raw materials instead of waste

disposal

Machine, accessories and packaging should be sorted for environment-friendly recycling. These instructions are printed on recycling paper manufactured without chlorine

09 Susanne Draenert

Operating Instructions for the Radius-Seam Metal Shear 3514-7R

To avoid any disturbance please read the following instructions:

For your safety:

1 2 3 4 5

1 Safe operation of this machine is possible only when the operating instructions and the safety precautions are read completely and the instructions contained therein are strictly observed.

2 The machine must not be used in a wet environment.

3 Always inspect cable and plug before using machine.

Only have damage repaired by a qualified professional. Put the plug into the mains socket only when the machine is switched off.

4+5 Always wears protective goggles, protective gloves and heavy-duty shoes when working.

Do not carry the machine by the cable.

Always remove the plug from the power supply socket before carrying out any work on the machine, when interrupting work and when not using the machine.

Always place the cable to the rear away from the machine.

Apply the machine to the sheet metal only when switched on.

Always provide for secure footing when working.

Firmly clamp the work piece if it does not remain stationary from its own weight.

The knife should not rub on the jaws: Possible danger of cutting tool breakage.

Do not exceed the maximum allowable material thickness especially when cutting over double folded joints or welded seams.

For further notes on safety refer to enclosed sheet

DRÄCO Radius Seam Metal Shear

type

3514-7R

max. cutting capacity

Art.no.

61080

spare parts

steel

400 N/mm²

mm/ga.

2,0 / 14

knife

371401

stainless steel

600 N/mm²

mm/ga.

1,5 / 16

set of jaws

BG37222

stainless steel

800 N/mm²

mm/ga.

1,3 / 18

knife-pin set

BG35055

aluminium

250 N/mm²

mm/ga.

3,0 / 10

duct- & Pittsburgh Seam

400 N/mm²

mm/ga.

4 x 0,75 / 21

optional accessories

tightest radius

mm/ “

45 / 1¾

metal-box

18000

working speed ±

m/min

5-7

strokes

min

-1

2400

motor capacity

Watts

500

weight

kg2starting hole

Ø mm

0óI

spiral ducting starting hole 12-14 mm Ø

accurate cutting along a marked line

20.11.2015 Specifications are subject to change for improvement without prior notice.

Replacing/Adjusting the Knife

Before working on machine disconnect from power supply by removing plug from socket. Wear protective glasses!

Replacing the Knife

Clamp the machine in a vice on the clamping surfaces SV between aluminium protective jaws.

Unscrew the screws 70 and remove the spring plate 71. Remove the spring 72. Remove the Cotter Pin 76 and the Washer

77. Push back the knife pin 78.

Do NOT interchange the Spacing Shims 79: the wrong spacing could ruin the jaws and knife. Insert a new knife with the old spacing Shims 79. Insert the knife pin

8. Mount the washer 77 and the Cotter Pin 76. Insert the spring 72. Reassemble spring plate 71.

Replacing the Jaws

Loosen the screws 80 and remove the jaws 82. Press out the positioning pins 81. Mount new jaws and positioning pins. Tighten the screws 80.

Adjusting the knife Clearance

For clearance between knife and jaws that is too large, loosen the fillister head screw 67. Adjust the clearance with the setscrew 68. Retighten the fillister head screw 67.

The knife must not rub on the jaws: Danger of breakage. Note: If heavy burring is produced while cutting, repeat the adjustment.

Sharpening the Knife/Jaws

The Knife and the Jaws must be sharpened and adjusted at the same time. This work should be performed by an authorised DRÄCO customer service location. Send in the complete machine for this purpose.

Spare part List DRÄCO Radius Seam Metal Shear 3514-7R

Pos.

Description

Qty.

Order-No.

Pos.

Description

Qty.

Order-No.

Shear Head 3514-7R cpl. assembl.

37515

Washer 381059

Pos. 35, 39, 44-82

Ball Bearing

13039

Gear 113540

Pinion 113041

Drive Shaft cpl. Pos. 54-62

BG31558

Sleeve 113042

Pinion with Gear cpl. Pos. 39, 44-47

BG31541

Needle Bearing

13043

Motor cpl. 230 V

32229

Securing Washer

81249

Motor cpl. 115 V

32129

Screw 381262

Gear Case Cover Pos. 48-53

BG13046

Motor Housing

32040

Securing Washer

81243

Housing Cap

32047

Hex Socket Screw

81031

Switch132050

Circlip 110009

Guide Piece

32054

Key110006

Switch Pad

32056

Gear 113051

Pressure Spring

32055

Cover for Needle Bearing Pos. 57+59

BG10450

Wire232044

58+62

Sleeve 110005

Carbon Brush

32042

59+63

Needle Bearing

10300

Carbon Brush Holder

32041

Roller Bearing

35285

Condensator

32045

Eccentric Shaft assembled Pos. 54+55,60-62

BG35556

Cable with Plug

32046

Head Casting Pos. 63-65+69

BG37547

Connection Cable

32522

Knife Pin Bushing

35542

Screw 232048

Spacing Block Pos. 66-68

BG37059

Screw 232053

Screw 181176

Cable Collar

32052

Tap Screw

81120

Field 230 V

32039

Tap Screw

81239

Field 115 V

32139

Screw 481285

Air Deflector Ring

32038

Spring Cover Plate

12300

Rubber Sleeve

32036

Spring Cover Plate Pos. 70-72

BG12300

Ball Bearing

32030

Spring112200

Washer132037

73-74

Knife Adjust Screw with Locking

35566

Armature 230 V

32033

73-75

Knife 3514-7R

37140

Armature 115 V

32133

78-79

Knife-pin set BG12400+BG35145

BG35055

Bearing Cover

32032

Safety Cotter Pin

35054

Ball Bearing

10038

Washer 281072

Securing Ring

32034

Knife Pin Pos. 76-78

BG35145

Bearing End Plate

32014

Spacing Shims Set

BG12400

Screw 432010

Screw 481440

Pin 181132

Pin 481248

Screw 232012

Set of Jaws 3514-7R

37222

Rating Plate

32057

Set of Jaws 3514-7R Pos. 80-82

BG37222

Max Draenert GmbH & Co.KG

Electric - Cordless - Pneumatic Tools - Machines

Germany

Werk I:

Administration

D-73777 Deizisau

P.O.Box

1120

Tel.

+49-7153-8217-0

Production Shears K-Series

D-73779 Deizisau

Gutenbergstreet

15-17

Fax

+49-7153-8217-66

Internet

http://www.dracotools.com

E-mail:

draenert@dracotools.com

20.11.2015 Specifications are subject to change for improvement without prior notice.

Replacing/Adjusting the Knife

Before working on machine disconnect from power supply by removing plug from socket. Wear protective glasses!

Replacing the Knife

Clamp the machine in a vice on the clamping surfaces SV between aluminium protective jaws.

Unscrew the screws 70 and remove the spring plate 71. Remove the spring 72. Remove the Cotter Pin 76 and the Washer

77. Push back the knife pin 78.

Do NOT interchange the Spacing Shims 79: the wrong spacing could ruin the jaws and knife. Insert a new knife with the old spacing Shims 79. Insert the knife pin

8. Mount the washer 77 and the Cotter Pin 76. Insert the spring 72. Reassemble spring plate 71.

Replacing the Jaws

Loosen the screws 80 and remove the jaws 82. Press out the positioning pins 81. Mount new jaws and positioning pins. Tighten the screws 80.

Adjusting the knife Clearance

For clearance between knife and jaws that is too large, loosen the fillister head screw 67. Adjust the clearance with the setscrew 68. Retighten the fillister head screw 67.

The knife must not rub on the jaws: Danger of breakage. Note: If heavy burring is produced while cutting, repeat the adjustment.

Sharpening the Knife/Jaws

The Knife and the Jaws must be sharpened and adjusted at the same time. This work should be performed by an authorised DRÄCO customer service location. Send in the complete machine for this purpose.

Spare part List DRÄCO Radius Seam Metal Shear 3514-7R

Pos.

Description

Qty.

Order-No.

Pos.

Description

Qty.

Order-No.

Shear Head 3514-7R cpl. assembl.

37515

Washer 381059

Pos. 35, 39, 44-82

Ball Bearing

13039

Gear 113540

Pinion 113041

Drive Shaft cpl. Pos. 54-62

BG31558

Sleeve 113042

Pinion with Gear cpl. Pos. 39, 44-47

BG31541

Needle Bearing

13043

Motor cpl. 230 V

32229

Securing Washer

81249

Motor cpl. 115 V

32129

Screw 381262

Gear Case Cover Pos. 48-53

BG13046

Motor Housing

32040

Securing Washer

81243

Housing Cap

32047

Hex Socket Screw

81031

Switch132050

Circlip 110009

Guide Piece

32054

Key110006

Switch Pad

32056

Gear 113051

Pressure Spring

32055

Cover for Needle Bearing Pos. 57+59

BG10450

Wire232044

58+62

Sleeve 110005

Carbon Brush

32042

59+63

Needle Bearing

10300

Carbon Brush Holder

32041

Roller Bearing

35285

Condensator

32045

Eccentric Shaft assembled Pos. 54+55,60-62

BG35556

Cable with Plug

32046

Head Casting Pos. 63-65+69

BG37547

Connection Cable

32522

Knife Pin Bushing

35542

Screw 232048

Spacing Block Pos. 66-68

BG37059

Screw 232053

Screw 181176

Cable Collar

32052

Tap Screw

81120

Field 230 V

32039

Tap Screw

81239

Field 115 V

32139

Screw 481285

Air Deflector Ring

32038

Spring Cover Plate

12300

Rubber Sleeve

32036

Spring Cover Plate Pos. 70-72

BG12300

Ball Bearing

32030

Spring112200

Washer132037

73-74

Knife Adjust Screw with Locking

35566

Armature 230 V

32033

73-75

Knife 3514-7R

37140

Armature 115 V

32133

78-79

Knife-pin set BG12400+BG35145

BG35055

Bearing Cover

32032

Safety Cotter Pin

35054

Ball Bearing

10038

Washer 281072

Securing Ring

32034

Knife Pin Pos. 76-78

BG35145

Bearing End Plate

32014

Spacing Shims Set

BG12400

Screw 432010

Screw 481440

Pin 181132

Pin 481248

Screw 232012

Set of Jaws 3514-7R

37222

Rating Plate

32057

Set of Jaws 3514-7R Pos. 80-82

BG37222

Max Draenert GmbH & Co.KG

Electric - Cordless - Pneumatic Tools - Machines

Germany

Werk I:

Administration

D-73777 Deizisau

P.O.Box

1120

Tel.

+49-7153-8217-0

Production Shears K-Series

D-73779 Deizisau

Gutenbergstreet

15-17

Fax

+49-7153-8217-66

Internet

http://www.dracotools.com

E-mail:

draenert@dracotools.com

20.11.2015 Specifications are subject to change for improvement without prior notice.

Replacing/Adjusting the Knife

Before working on machine disconnect from power supply by removing plug from socket. Wear protective glasses!

Replacing the Knife

Clamp the machine in a vice on the clamping surfaces SV between aluminium protective jaws.

Unscrew the screws 70 and remove the spring plate 71. Remove the spring 72. Remove the Cotter Pin 76 and the Washer

77. Push back the knife pin 78.

Do NOT interchange the Spacing Shims 79: the wrong spacing could ruin the jaws and knife. Insert a new knife with the old spacing Shims 79. Insert the knife pin

8. Mount the washer 77 and the Cotter Pin 76. Insert the spring 72. Reassemble spring plate 71.

Replacing the Jaws

Loosen the screws 80 and remove the jaws 82. Press out the positioning pins 81. Mount new jaws and positioning pins. Tighten the screws 80.

Adjusting the knife Clearance

For clearance between knife and jaws that is too large, loosen the fillister head screw 67. Adjust the clearance with the setscrew 68. Retighten the fillister head screw 67.

The knife must not rub on the jaws: Danger of breakage. Note: If heavy burring is produced while cutting, repeat the adjustment.

Sharpening the Knife/Jaws

The Knife and the Jaws must be sharpened and adjusted at the same time. This work should be performed by an authorised DRÄCO customer service location. Send in the complete machine for this purpose.

Spare part List DRÄCO Radius Seam Metal Shear 3514-7R

Pos.

Description

Qty.

Order-No.

Pos.

Description

Qty.

Order-No.

Shear Head 3514-7R cpl. assembl.

37515

Washer 381059

Pos. 35, 39, 44-82

Ball Bearing

13039

Gear 113540

Pinion 113041

Drive Shaft cpl. Pos. 54-62

BG31558

Sleeve 113042

Pinion with Gear cpl. Pos. 39, 44-47

BG31541

Needle Bearing

13043

Motor cpl. 230 V

32229

Securing Washer

81249

Motor cpl. 115 V

32129

Screw 381262

Gear Case Cover Pos. 48-53

BG13046

Motor Housing

32040

Securing Washer

81243

Housing Cap

32047

Hex Socket Screw

81031

Switch132050

Circlip 110009

Guide Piece

32054

Key110006

Switch Pad

32056

Gear 113051

Pressure Spring

32055

Cover for Needle Bearing Pos. 57+59

BG10450

Wire232044

58+62

Sleeve 110005

Carbon Brush

32042

59+63

Needle Bearing

10300

Carbon Brush Holder

32041

Roller Bearing

35285

Condensator

32045

Eccentric Shaft assembled Pos. 54+55,60-62

BG35556

Cable with Plug

32046

Head Casting Pos. 63-65+69

BG37547

Connection Cable

32522

Knife Pin Bushing

35542

Screw 232048

Spacing Block Pos. 66-68

BG37059

Screw 232053

Screw 181176

Cable Collar

32052

Tap Screw

81120

Field 230 V

32039

Tap Screw

81239

Field 115 V

32139

Screw 481285

Air Deflector Ring

32038

Spring Cover Plate

12300

Rubber Sleeve

32036

Spring Cover Plate Pos. 70-72

BG12300

Ball Bearing

32030

Spring112200

Washer132037

73-74

Knife Adjust Screw with Locking

35566

Armature 230 V

32033

73-75

Knife 3514-7R

37140

Armature 115 V

32133

78-79

Knife-pin set BG12400+BG35145

BG35055

Bearing Cover

32032

Safety Cotter Pin

35054

Ball Bearing

10038

Washer 281072

Securing Ring

32034

Knife Pin Pos. 76-78

BG35145

Bearing End Plate

32014

Spacing Shims Set

BG12400

Screw 432010

Screw 481440

Pin 181132

Pin 481248

Screw 232012

Set of Jaws 3514-7R

37222

Rating Plate

32057

Set of Jaws 3514-7R Pos. 80-82

BG37222

Max Draenert GmbH & Co.KG

Electric - Cordless - Pneumatic Tools - Machines

Germany

Werk I:

Administration

D-73777 Deizisau

P.O.Box

1120

Tel.

+49-7153-8217-0

Production Shears K-Series

D-73779 Deizisau

Gutenbergstreet

15-17

Fax

+49-7153-8217-66

Internet

http://www.dracotools.com

E-mail:

draenert@dracotools.com

20.11.2015 Specifications are subject to change for improvement without prior notice.

Replacing/Adjusting the Knife

Before working on machine disconnect from power supply by removing plug from socket. Wear protective glasses!

Replacing the Knife

Clamp the machine in a vice on the clamping surfaces SV between aluminium protective jaws.

Unscrew the screws 70 and remove the spring plate 71. Remove the spring 72. Remove the Cotter Pin 76 and the Washer

77. Push back the knife pin 78.

Do NOT interchange the Spacing Shims 79: the wrong spacing could ruin the jaws and knife. Insert a new knife with the old spacing Shims 79. Insert the knife pin

8. Mount the washer 77 and the Cotter Pin 76. Insert the spring 72. Reassemble spring plate 71.

Replacing the Jaws

Loosen the screws 80 and remove the jaws 82. Press out the positioning pins 81. Mount new jaws and positioning pins. Tighten the screws 80.

Adjusting the knife Clearance

For clearance between knife and jaws that is too large, loosen the fillister head screw 67. Adjust the clearance with the setscrew 68. Retighten the fillister head screw 67.

The knife must not rub on the jaws: Danger of breakage. Note: If heavy burring is produced while cutting, repeat the adjustment.

Sharpening the Knife/Jaws

The Knife and the Jaws must be sharpened and adjusted at the same time. This work should be performed by an authorised DRÄCO customer service location. Send in the complete machine for this purpose.

Spare part List DRÄCO Radius Seam Metal Shear 3514-7R

Pos.

Description

Qty.

Order-No.

Pos.

Description

Qty.

Order-No.

Shear Head 3514-7R cpl. assembl.

37515

Washer 381059

Pos. 35, 39, 44-82

Ball Bearing

13039

Gear 113540

Pinion 113041

Drive Shaft cpl. Pos. 54-62

BG31558

Sleeve 113042

Pinion with Gear cpl. Pos. 39, 44-47

BG31541

Needle Bearing

13043

Motor cpl. 230 V

32229

Securing Washer

81249

Motor cpl. 115 V

32129

Screw 381262

Gear Case Cover Pos. 48-53

BG13046

Motor Housing

32040

Securing Washer

81243

Housing Cap

32047

Hex Socket Screw

81031

Switch132050

Circlip 110009

Guide Piece

32054

Key110006

Switch Pad

32056

Gear 113051

Pressure Spring

32055

Cover for Needle Bearing Pos. 57+59

BG10450

Wire232044

58+62

Sleeve 110005

Carbon Brush

32042

59+63

Needle Bearing

10300

Carbon Brush Holder

32041

Roller Bearing

35285

Condensator

32045

Eccentric Shaft assembled Pos. 54+55,60-62

BG35556

Cable with Plug

32046

Head Casting Pos. 63-65+69

BG37547

Connection Cable

32522

Knife Pin Bushing

35542

Screw 232048

Spacing Block Pos. 66-68

BG37059

Screw 232053

Screw 181176

Cable Collar

32052

Tap Screw

81120

Field 230 V

32039

Tap Screw

81239

Field 115 V

32139

Screw 481285

Air Deflector Ring

32038

Spring Cover Plate

12300

Rubber Sleeve

32036

Spring Cover Plate Pos. 70-72

BG12300

Ball Bearing

32030

Spring112200

Washer132037

73-74

Knife Adjust Screw with Locking

35566

Armature 230 V

32033

73-75

Knife 3514-7R

37140

Armature 115 V

32133

78-79

Knife-pin set BG12400+BG35145

BG35055

Bearing Cover

32032

Safety Cotter Pin

35054

Ball Bearing

10038

Washer 281072

Securing Ring

32034

Knife Pin Pos. 76-78

BG35145

Bearing End Plate

32014

Spacing Shims Set

BG12400

Screw 432010

Screw 481440

Pin 181132

Pin 481248

Screw 232012

Set of Jaws 3514-7R

37222

Rating Plate

32057

Set of Jaws 3514-7R Pos. 80-82

BG37222

Max Draenert GmbH & Co.KG

Electric - Cordless - Pneumatic Tools - Machines

Germany

Werk I:

Administration

D-73777 Deizisau

P.O.Box

1120

Tel.

+49-7153-8217-0

Production Shears K-Series

D-73779 Deizisau

Gutenbergstreet

15-17

Fax

+49-7153-8217-66

Internet

http://www.dracotools.com

E-mail:

draenert@dracotools.com

20.11.2015 Specifications are subject to change for improvement without prior notice.

Replacing/Adjusting the Knife

Before working on machine disconnect from power supply by removing plug from socket. Wear protective glasses!

Replacing the Knife

Clamp the machine in a vice on the clamping surfaces SV between aluminium protective jaws.

Unscrew the screws 70 and remove the spring plate 71. Remove the spring 72. Remove the Cotter Pin 76 and the Washer

77. Push back the knife pin 78.

Do NOT interchange the Spacing Shims 79: the wrong spacing could ruin the jaws and knife. Insert a new knife with the old spacing Shims 79. Insert the knife pin

8. Mount the washer 77 and the Cotter Pin 76. Insert the spring 72. Reassemble spring plate 71.

Replacing the Jaws

Loosen the screws 80 and remove the jaws 82. Press out the positioning pins 81. Mount new jaws and positioning pins. Tighten the screws 80.

Adjusting the knife Clearance

For clearance between knife and jaws that is too large, loosen the fillister head screw 67. Adjust the clearance with the setscrew 68. Retighten the fillister head screw 67.

The knife must not rub on the jaws: Danger of breakage. Note: If heavy burring is produced while cutting, repeat the adjustment.

Sharpening the Knife/Jaws

The Knife and the Jaws must be sharpened and adjusted at the same time. This work should be performed by an authorised DRÄCO customer service location. Send in the complete machine for this purpose.

Spare part List DRÄCO Radius Seam Metal Shear 3514-7R

Pos.

Description

Qty.

Order-No.

Pos.

Description

Qty.

Order-No.

Shear Head 3514-7R cpl. assembl.

37515

Washer 381059

Pos. 35, 39, 44-82

Ball Bearing

13039

Gear 113540

Pinion 113041

Drive Shaft cpl. Pos. 54-62

BG31558

Sleeve 113042

Pinion with Gear cpl. Pos. 39, 44-47

BG31541

Needle Bearing

13043

Motor cpl. 230 V

32229

Securing Washer

81249

Motor cpl. 115 V

32129

Screw 381262

Gear Case Cover Pos. 48-53

BG13046

Motor Housing

32040

Securing Washer

81243

Housing Cap

32047

Hex Socket Screw

81031

Switch132050

Circlip 110009

Guide Piece

32054

Key110006

Switch Pad

32056

Gear 113051

Pressure Spring

32055

Cover for Needle Bearing Pos. 57+59

BG10450

Wire232044

58+62

Sleeve 110005

Carbon Brush

32042

59+63

Needle Bearing

10300

Carbon Brush Holder

32041

Roller Bearing

35285

Condensator

32045

Eccentric Shaft assembled Pos. 54+55,60-62

BG35556

Cable with Plug

32046

Head Casting Pos. 63-65+69

BG37547

Connection Cable

32522

Knife Pin Bushing

35542

Screw 232048

Spacing Block Pos. 66-68

BG37059

Screw 232053

Screw 181176

Cable Collar

32052

Tap Screw

81120

Field 230 V

32039

Tap Screw

81239

Field 115 V

32139

Screw 481285

Air Deflector Ring

32038

Spring Cover Plate

12300

Rubber Sleeve

32036

Spring Cover Plate Pos. 70-72

BG12300

Ball Bearing

32030

Spring112200

Washer132037

73-74

Knife Adjust Screw with Locking

35566

Armature 230 V

32033

73-75

Knife 3514-7R

37140

Armature 115 V

32133

78-79

Knife-pin set BG12400+BG35145

BG35055

Bearing Cover

32032

Safety Cotter Pin

35054

Ball Bearing

10038

Washer 281072

Securing Ring

32034

Knife Pin Pos. 76-78

BG35145

Bearing End Plate

32014

Spacing Shims Set

BG12400

Screw 432010

Screw 481440

Pin 181132

Pin 481248

Screw 232012

Set of Jaws 3514-7R

37222

Rating Plate

32057

Set of Jaws 3514-7R Pos. 80-82

BG37222

Max Draenert GmbH & Co.KG

Electric - Cordless - Pneumatic Tools - Machines

Germany

Werk I:

Administration

D-73777 Deizisau

P.O.Box

1120

Tel.

+49-7153-8217-0

Production Shears K-Series

D-73779 Deizisau

Gutenbergstreet

15-17

Fax

+49-7153-8217-66

Internet

http://www.dracotools.com

E-mail:

draenert@dracotools.com

20.11.2015 Specifications are subject to change for improvement without prior notice.

Replacing/Adjusting the Knife

Before working on machine disconnect from power supply by removing plug from socket. Wear protective glasses!

Replacing the Knife

Clamp the machine in a vice on the clamping surfaces SV between aluminium protective jaws.

Unscrew the screws 70 and remove the spring plate 71. Remove the spring 72. Remove the Cotter Pin 76 and the Washer

77. Push back the knife pin 78.

Do NOT interchange the Spacing Shims 79: the wrong spacing could ruin the jaws and knife. Insert a new knife with the old spacing Shims 79. Insert the knife pin

8. Mount the washer 77 and the Cotter Pin 76. Insert the spring 72. Reassemble spring plate 71.

Replacing the Jaws

Loosen the screws 80 and remove the jaws 82. Press out the positioning pins 81. Mount new jaws and positioning pins. Tighten the screws 80.

Adjusting the knife Clearance

For clearance between knife and jaws that is too large, loosen the fillister head screw 67. Adjust the clearance with the setscrew 68. Retighten the fillister head screw 67.

The knife must not rub on the jaws: Danger of breakage. Note: If heavy burring is produced while cutting, repeat the adjustment.

Sharpening the Knife/Jaws

The Knife and the Jaws must be sharpened and adjusted at the same time. This work should be performed by an authorised DRÄCO customer service location. Send in the complete machine for this purpose.

Spare part List DRÄCO Radius Seam Metal Shear 3514-7R

Pos.

Description

Qty.

Order-No.

Pos.

Description

Qty.

Order-No.

Shear Head 3514-7R cpl. assembl.

37515

Washer 381059

Pos. 35, 39, 44-82

Ball Bearing

13039

Gear 113540

Pinion 113041

Drive Shaft cpl. Pos. 54-62

BG31558

Sleeve 113042

Pinion with Gear cpl. Pos. 39, 44-47

BG31541

Needle Bearing

13043

Motor cpl. 230 V

32229

Securing Washer

81249

Motor cpl. 115 V

32129

Screw 381262

Gear Case Cover Pos. 48-53

BG13046

Motor Housing

32040

Securing Washer

81243

Housing Cap

32047

Hex Socket Screw

81031

Switch132050

Circlip 110009

Guide Piece

32054

Key110006

Switch Pad

32056

Gear 113051

Pressure Spring

32055

Cover for Needle Bearing Pos. 57+59

BG10450

Wire232044

58+62

Sleeve 110005

Carbon Brush

32042

59+63

Needle Bearing

10300

Carbon Brush Holder

32041

Roller Bearing

35285

Condensator

32045

Eccentric Shaft assembled Pos. 54+55,60-62

BG35556

Cable with Plug

32046

Head Casting Pos. 63-65+69

BG37547

Connection Cable

32522

Knife Pin Bushing

35542

Screw 232048

Spacing Block Pos. 66-68

BG37059

Screw 232053

Screw 181176

Cable Collar

32052

Tap Screw

81120

Field 230 V

32039

Tap Screw

81239

Field 115 V

32139

Screw 481285

Air Deflector Ring

32038

Spring Cover Plate

12300

Rubber Sleeve

32036

Spring Cover Plate Pos. 70-72

BG12300

Ball Bearing

32030

Spring112200

Washer132037

73-74

Knife Adjust Screw with Locking

35566

Armature 230 V

32033

73-75

Knife 3514-7R

37140

Armature 115 V

32133

78-79

Knife-pin set BG12400+BG35145

BG35055

Bearing Cover

32032

Safety Cotter Pin

35054

Ball Bearing

10038

Washer 281072

Securing Ring

32034

Knife Pin Pos. 76-78

BG35145

Bearing End Plate

32014

Spacing Shims Set

BG12400

Screw 432010

Screw 481440

Pin 181132

Pin 481248

Screw 232012

Set of Jaws 3514-7R

37222

Rating Plate

32057

Set of Jaws 3514-7R Pos. 80-82

BG37222

Max Draenert GmbH & Co.KG

Electric - Cordless - Pneumatic Tools - Machines

Germany

Werk I:

Administration

D-73777 Deizisau

P.O.Box

1120

Tel.

+49-7153-8217-0

Production Shears K-Series

D-73779 Deizisau

Gutenbergstreet

15-17

Fax

+49-7153-8217-66

Internet

http://www.dracotools.com

E-mail:

draenert@dracotools.com

Draco 3514-7R Operating Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual