Doyon CPF512, CPF516, CPF416, CPF522, CPF422 Instructions Manual

BREAD SLICER

CPF412, CPF416, CPF422, CPF512, CPF516, CPF522

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

DANGER

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

CAREFULLY FOLLOW THESE INSTRUCTIONS

TABLE OF CONTENTS

SECTION « A » DESCRIPTION PAGE

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A1

Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A2

Shipping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A2

Installation warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A4

Operation of the bread slicer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A5

Instructions to remove the blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A7

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A8

For more information, please contact our office : . . . . . . . . . . . . . . . . . . . A9

SECTION « B » DIMENSIONS

CFP412, 416 & 422. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B1

CPF512, 516 & 522. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B2

SECTION « E » COMPONENT PARTS

CFP412, 416 , 422 & CFP512, 516, 522 . . . . . . . . . . . . . . . . . . . . . . . . . . E1

SECTION « G » ELECTRIC SCHEMATIC

CPF412, 416, 422 & CPF512, 516, 522 . . . . . . . . . . . . . . . . . . . . . . . . . . . G1

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

CPF1-A.DOC Rev. 05-2007

A1

INTRODUCTION

CAUTION

READ ALL INSTRUCTIONS

The manufacturer suggests to read this manual carefully.

This bread slicer is manufactured with first quality material by experienced technicians. Proper
installation and maintenance will guarantee a reliable service for years to come.

A nameplate fixed to the slicer specifies the model number, serial number, voltage and amperage.

ATTENTION

DOYON is not responsible for damages to the property or the equipment caused
by personnel who is not certified by known organisations. The customer is
responsible for finding qualified technicians in electricity.

A2

CONSTRUCTION

You just bought the most advanced bread slicer in the world, "DOYON" technology at its best. This
slicer is manufactured using the highest quality components and material.

SHIPPING

For your safety, this equipment has been verified by qualified technicians and carefully crated before
shipment. The freight company assumes full responsibility concerning the delivery in good condition
of the equipment in accepting to transport it.

IMPORTANT

RECEPTION OF THE MERCHANDISE

Take care to verify that the received equipment is not damaged before signing the delivery receipt. If
a damage or a lost part is noticed, write it clearly on the receipt. If it is noticed after the carrier has
left, contact immediately the freight company in order that they do their inspection.

We do not assume the responsibility for damages or losses that may occur during transportation.

A3

INSTALLATION WARNINGS

POWER FAILURE WARNING

WHEN YOU HAVE A POWER FAILURE, SHUT OFF THE BREAD SLICER POWER

SWITCH TO PROTECT THE ELECTRIC COMPONENTS WHEN THE POWER COMES

BACK.

FOR YOUR SAFETY

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS

AND LIQUIDS IN THE VICINITY OF THIS OR ANY APPLIANCE.

INSTALLATION AND SERVICE

WARNING

IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR

MAINTENANCE CAN CAUSE PROPERTY DAMAGE, INJURY OR DEATH.

READ THE INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS

THOROUGHLY BEFORE INSTALLING OR SERVICING THIS EQUIPMENT.

Installation and service must be done by specialised technicians. Contact a certified electrician.

The bread slicer must be connected to the utility and electrically grounded in conformity to the
effective local regulations. If these are not established, the oven must be connected according to the
Canadian Electrical Code (CSA-C22.1-XX) or National Electrical Code (NFPA 70-XX). Refer to
last edition year for XX. Installation must also allow proper access for service (24 inches each side
and back).

A4

INSTALLATION

IN GENERAL

Take off the packaging material with care. Take off all the material used for packing and
accessories.

1. To the electrician

Electrical supply installation must be in accordance with the electrical rating on the nameplate.

A5

OPERATION OF THE BREAD SLICER

Adjust the position of the finger at high or low position according with your bread, with the black
adjustment screw. (picture A)

A

1. Turn the main switch to the [ I ] position.

2. Twist out the emergency stop switch.

3. Push the lever partway.

21

4. Insert the bread.

5. Push the lever again all the way back to start the slicer.

4

5

6. Let go and restrain the lever tension as not to crush the bread.

6 7 8

3

6

7. When the bread is sliced, the slicer stops working.

8. Remove bread from the outlet.