Dovre 280 Electric, 425 Electric Instructions For Use Installation And Servicing
PR1258 Issue 3 (October 2014)
IMPORTANT
THE OUTER CASING, FRONT AND GLASS PANEL BECOME EXTREMELY HOT DURING OPERATION AND
WILL RESULT IN SERIOUS INJURY AND BURNS IF TOUCHED. IT IS THEREFORE RECOMMENDED THAT A
FIREGUARD COMPLYING WITH BS 8423:2002 IS USED IN THE PRESENCE OF YOUNG CHILDREN, THE
ELDERLY OR INFIRM.
For use with 230v 50Hz electricity supply only.
Please read these instructions carefully before installation and keep them in a safe place.
They will be needed when maintenance or servicing is required.
THIS APPLIANCE MUST BE EARTHED
Instructions for Use, Installation and Servicing
For use in GB, IE (Great Britain and Republic of Ireland)
Dovre 280 or 425 Electric
2
User Instructions .......................................................3
1. Important Information & Health and Safety ............................ 3
2. Operating Instructions ............................................................ 3
3. Maintenance ........................................................................... 5
4. Removing & Replacing Doors ................................................ 5
Installation Instructions ............................................6
Technical Specifications ............................................................. 6
Appliance Dimensions ................................................................ 6
Installation ..................................................................7
1. Fitting Appliances ................................................................... 7
Servicing ....................................................................8
1. Fault Finding...........................................................................8
2. How to Wire a Plug ................................................................ 8
3. Servicing Requirements ......................................................... 9
4. Replacing the front LED Board .............................................. 9
5. Replacing the PCB ................................................................. 9
6. Replacing the Motor & Effects Unit ........................................ 9
7. Replacing the Middle LED Board ......................................... 10
8. Replacing the Rear LED Board ............................................ 10
9. Replacing the Heater Assembly ...........................................10
Spare Parts List ....................................................... 11
Contents
Covering the following models:
Registration No WEE/DH1656ZW
In accordance with European Directive 2002/96/
EC, waste electrical and electronic equipment
(WEEE) must not be disposed of with household
waste.
At the end of its useful life please take this
product to an appropriate recycling centre or
collection point. You can nd your nearest
recycling centre by using the bank locator at
www.recycle-more.co.uk for UK customers,
www.weeeireland.ie for customers in the
Republic of Ireland, or by contacting your local
authority.
Model Dovre 280 Dovre 425
Black DV-280E DV-425E
White Ivory Enamel DV641-809 DV641-818
To receive your Extended Warranty your Dovre appliance must have
been purchased from our Expert Retailer Network and registered within
one month of purchase or installation. Please note that all warranties
are effective from the date of purchase. Any Dovre product purchased
outside of our Extended Retailer Network, or not registered within the
stated time will carry a standard 12 month warranty.
Full terms and conditions are detailed in the Warranty Statement on
the Dovre website www.dovre.co.uk. In the event of any conflict of
information the wording on the website shall prevail.
Important Note: Should any problems be experienced with your
product, claims must first be submitted to the Expert Retailer where
the appliance was purchased from who will offer immediate assistance
or contact Dovre on your behalf.
3
User Instructions
How to use these instructions
The contents of Sections 1, 2 and 3 apply to all the
models in our Electric Range.
The content of Section 4, Remove and Replace Door,
gives different instructions for each model type.
Select the relevant information for your model.
1. Important Information and
Health and Safety
ALL APPLIANCES DESCRIBED IN THESE
INSTRUCTIONS ARE HEAVY. SEEK ASSISTANCE
BEFORE UNLOADING AND LIFTING.
1.1 Read all of the instructions carefully before using the
appliance.
1.2 Remove all packaging and dispose of at an appropriate
recycling facility.
1.3 To remove the protective packaging and fitting kit from
inside a new appliance, choose the instruction
corresponding to your model from Section 4.
1.4 Do not locate this appliance immediately below a fixed
socket outlet.
1.5 The outer casing of this appliance is considered by the
manufacturer to be a working surface which becomes hot
when the fire is switched on. You must use a suitable fire
guard to protect children, the elderly and the infirm.
1.6 Do not use this appliance in the immediate surroundings of
a bath, shower, swimming pool or any other area where
the appliance could come into contact with water or
humidity, e.g. a bathroom.
1.7 WARNING! DO NOT COVER
Do not allow the appliance to be covered or let the air inlet/
outlet become obstructed as the appliance may overheat.
Please note the warning symbol on the appliance (see
above).
1.8 For indoor use only. This appliance is not suitable for use
outside the house.
1.9 Keep the power cord away from hot surfaces and hot
conditions. Do not route the power lead in front of the
appliance.
1.10 This appliance must stand on a clean, level, firm surface. Do
not stand the fire on a carpet. Ensure that furniture, curtains
etc. are positioned no closer than 1m and the fire stands on
a surface that can withstand temperatures of 90°C for
prolonged periods. Do not allow rugs to be placed within
500mm of the front of the appliance.
1.11 When the fire has been installed, the position of the plug
must be accessible.
1.12 Where the electricity supply cable has to pass through a
fire place, stone surround etc. ensure suitable rubber
bushes are fitted at possible wear points.
1.13 If installed in an open fireplace, blank off the chimney to
reduce the risk of a back draught which can cause the
safety cut-out to operate.
1.14 If the electricity supply cable is damaged do not use the
appliance until it has been replaced. For safety reasons the
replacement has to be carried out by Dovre, a Dovre service
agent or a similarly competent electrician.
1.15 Do not use this appliance with any kind of timer,
programmer or thermal control or other device that will
switch the appliance on or off automatically.
1.16 Do not operate the appliance if it is damaged.
1.17 Repairs of electrical appliances must only be performed by
an electrical engineer. Should the appliance fail to operate,
or in case of any damage, please contact the retailer from
whom the appliance was purchased.
1.18 Never leave the heater unattended while it is in use.
Always switch the product to the OFF position and unplug it
from the electrical outlet when not in use.
1.19 This appliance is not intended to be used by persons
under the age of 12, persons with reduced physical,
sensory or mental capabilities or persons with lack of
experience and knowledge in the safe operation of the
appliance.
The appliance may be operated by persons above the
age of 12 provided they have been instructed in the safe
use of the appliance and that they understand the hazards
involved. Persons above the age of 12 may also operate the
appliance under the supervision of a responsible adult.
1.20 Parts of this appliance become hot whilst in operation and
under no circumstances should persons under the age of 12
be left alone with the product when it is in operation unless
a suitable fireguard is used to protect them against the
possibility of coming into direct contact with the appliance.
2. Operating Instructions
WARNING! Do not operate the appliance if it is
damaged or has malfunctioned. If you suspect
the appliance is damaged or has malfunctioned
call a qualified service engineer to inspect the
appliance, and replace any part of the electrical
system if necessary, before reuse.
GENERAL
2.1 The appliance can be operated by the infrared handset or
the manual controls on the bottom right hand side of the
appliance.
PREPARATION BEFORE USE
Batteries:
2.2 Ensure that the handset battery is new and is inserted
correctly.
4
2.3 Dispose of old batteries at an appropriate recycling facility.
When using the handset:
2.4 Ensure the handset is pointed at the infrared sensor
located behind the flame effect screen at the back of the
inside of the appliance.
LOCATION OF POWER SWITCH
2.5 The mains power switch is located on the control panel on
the lower right-hand side of the appliance, see Diagram 1.
2.6 Switch ON (—) before operating either the remote or
manual controls.
2.7 A beep is heard to indicate the fire is ready for use.
Remote & Manual Operation
2.8 The following functions can be controlled using the manual
controls or remote handset:
—Heat settings 1 and 2
—Brightness of the fuel and flame effect
—Colour of the flames
2.9 The Standby function and the thermostat can only be
operated via the manual controls.
2.10 The effects can be turned off using the remote, returning the
appliance to Standby.
Flame effect button
Standby
On/Off Switch
Thermostat
Heat setting button
1
On/Off button
Flame effect
Heat setting 1kW
Heat setting 2kW
2
Standby On/Off
2.11 The appliance is in Standby mode when the power is
switched on via the manual control panel. You must have
this power supply ON (—) before using the manual or
remote controls (see 2.5).
Turning On the Appliance
Flame Effects:
2.12 The flame effect button on both the manual and remote
controls has 4 settings:
—Press once for maximum brightness of fuel and
flame effects.
—Press twice for medium brightness.
—Press three times for minimum brightness.
—Press four times for maximum brightness of fuel and
additional blue flame effects.
1 2 3 4
Maximum Medium Minimum
Maximum
plus blue
ame effects
Turning On the Heat:
2.13 When turning on the heater you must always press the
1kW button. Do not start the fire using the 2kW setting.
2.14 It is NOT advisable to run the heater without the flame
effects switched on.
2.15 Press the 1kW button to turn the fan heater ON. One
red indicator light will be displayed behind the flame effect
screen at the back of the inside of the appliance. The
appliance will blow cold air for approximately 8 seconds
before the heater comes on. On this setting the heater will
operate at half its maximum temperature.
2.16 Press the 2kW button once to turn the fan heater to its
maximum temperature. Two red indicator lights will be
displayed behind the flame effect screen at the back of the
inside of the appliance. After approximately 8 seconds the
heater will operate at its maximum temperature.
2.17 Pressing the 2kW button again will turn the heater OFF
and cold air will be blown for approximately 8 seconds to
cool the appliance.
2.18 Press the 1kW button to return to the lower heat setting.
2.19 Press the On/Off button to turn off ALL settings and
return to Standby. Cold air will be blown for
approximately 8 seconds to cool the appliance.
2.20 The appliance should be turned off via the On/Off
switch when it is not in use.
User Instructions
Loading...