Page 1
INSTALLATIEVOORSCHRIFTEN EN GEBRUIKSAANWIJZING
HOUTKACHEL
INSTALLATION INSTRUCTIONS AND OPERATING MANUAL
WOOD STOVE
INSTALLATION ET MODE D’EMPLOI
POELE A BOIS
EINBAUANLEITUNG UND GEBRAUCHSANWEISUNG
HOLZ-FEUERSTÄTTE
INSTRUCCIONES DE INSTALACIÓN Y USO
ESTUFA DE LEÑA
MONTERINGS- OG BRUKSANVISNING
PEISOVN
325CB
03.27100.1.00 - 02-2013
Page 2
Table of contents
Introduction 3
Declaration of conformity 3
Safety 4
Installation requirements 4
General 4
Chimney (flue) 4
Ventilationof the area 5
Floors and walls 5
Product description 6
Installation 6
General preparation 6
Preparing the outside air connection 8
Installing andconnecting 8
Use 9
First use 9
Fuel 9
Lighting 9
Burning wood 10
Controlling combustion air 11
Extinguishingthe fire 11
Removing ashes 11
Fog and mist 11
Solving problems 11
Maintenance 12
Chimney 12
Cleaning and other regular maintenance
activities 12
Spare parts 325CB 13
Appendix 1: Technical Data 14
Appendix 2: Dimensions 15
Appendix 3: Distance from combustible
material 17
Appendix 4: Diagnostic diagram 19
Index 20
2
Subjectto change becauseof technicalimprovements
Page 3
Introduction
Dear user,
In buying this DOVRE heating appliance, you have
chosen a high quality product. This product is part of a
new generation of energy-efficient and
environmentally-friendly heating appliances. These
appliances make optimum use of convection heat as
well as thermal radiation (radiant heat).
Your DOVRE appliance has been manufactured
with state-of-the-art production equipment. In the
unlikely event of a malfunction, you can always
rely on DOVRE for support andservice.
The appliance should not be modified; please
always use original parts.
The appliance is intended for use in a living room. It
shouldbe connected hermetically to a wellfunctioning chimney.
We advise you have the appliance installed by an
authorized and competent installer.
DOVRE cannot be held liable for any problems or
damage resulting from incorrect installation.
Observe the following safety regulations when
installing and using the appliance.
In this manual, you can readhow the DOVRE heating
appliance can be installed, used and maintained
safely. Should you requireadditional informationor
technical data, or should you experience an
installation problem, please first contact your supplier.
© 2012 DOVRE NV
Declaration of
conformity
Notified body: 2013
The undersigned
Dovre nv, Nijverheidsstraat 18 B-2381 Weelde hereby
declares
that the wood stove 325CB has been produced in
accordance with EN 13240.
Weelde01-08-2012
Due to continuous product improvement, the supplied
appliance specifications may vary from the
description in this brochure without prior notice.
DOVRE N.V.
Nijverheidsstraat 18 Tel: +32 (0) 14 65 91 91
B-2381 Weelde Fax: +32 (0) 14 65 90 09
Belgium E-mail : info@dovre.be
Subjectto change becauseof technicalimprovements
3
Page 4
Safety
Please note: All safety regulations must be
compliedwith strictly.
Please read carefully the instructions supplied
with the appliance for installation, use and
maintenance, before usingthe appliance.
The appliance must be installedin accordance
with the laws and requirements of your
country.
All local regulations and the regulations relating
to national and European standards must be
observed when installing the appliance.
The appliance should preferably beinstalledby
an authorizedinstaller. Installers will be aware
of the applicable regulations andrequirements.
The appliance is designed for heating
purposes. All surfaces, including the glass and
connecting tube, can get very hot (over 100°C)!
For operation, use a so-called "cold hand" oran
oven glove.
Safety distances from flammable materials
must be adheredto strictly.
Don't place any curtains, clothes, laundry or
othercombustible materials on or nearthe
appliance.
Don't use flammable or explosive substances
near the appliance when it is in use.
Avoid a chimney fire by having the chimney
swept regularly. Never burn wood with the door
open.
In the case of a chimney fire: close all air inlets
of the appliance and alert the fire brigade.
If the glass in the appliance is broken or
cracked, it must be replaced before you can
use the appliance again.
Make sure there is adequate ventilation in the
room where the appliance is installed. If
ventilation is insufficient, combustion will be
incomplete resulting in toxic gases being
producedand spread through the room. See
the chapter"Installation requirements" for more
information on ventilation.
Installation
requirements
General
The appliance must be connected tightly to a wellfunctioning chimney.
For the connection measurements: see the
appendix "Technical data".
Ask the fire brigadeand/or your insurance
company about any specific requirements and
regulations.
Chimney (flue)
The flue or chimney is needed for:
Removal of combustion gases via natural draught.
As the warm air in the flue or chimney is lighter
than the outside air, it rises.
Air intake, needed for the combustion of fuel in the
appliance.
A poorly-functioningflue or chimney can cause smoke
to escape into the room when the door is opened.
Damage caused by smoke emissions into the room is
not coveredby the warranty.
Do not connect multiple appliances (such as a
boiler for central heating) to the same flue,
unless local or national regulations allow this.
In the event of two connections ensure that the
difference in height between the connections is
no less than 200 mm.
Ask your installer for advice regarding the flue. Refer
to the European norm EN13384 for a correct
calculations for the flue.
The flue must satisfy the following requirements:
The flue or chimney must be made of fire-resistant
material, preferably ceramics or stainless steel.
The flue or chimney must be airtight and wellcleaned and guarantee sufficient draught.
4
Subjectto change becauseof technicalimprovements
Page 5
A draught/vacuum of 15-20Pa during normal
operationis ideal.
Starting from the flue spigot, the flue must run as
vertically as possible. Changes in direction and
horizontal pieces disrupt the outward flow of
combustion gases and may cause soot deposits.
To prevent combustion gases from cooling down
too much, which reduces the draught, ensure that
the interior diameter is not too big.
The flue or chimney should ideally have the same
diameter as the connection collar.
For the nominal diameter: see the appendix
"Technical data". If the smoke channel is well
insulated, the diameter may be slightly bigger
(upto 2x the section of the connection collar).
The section (area ) of the smoke channel must be
constant. Widersegments and (in particular)
narrowersegments disrupt the outward flow of
combustion gases.
When using a cover plate or exhaust hood : make
sure that the cover does not restrict the flue outlet
andthat the cap does not impede the outward flow
of combustion gases.
The flue must end in a zone that is not affected by
surrounding buildings, trees or otherobstacles.
The flue outside the house must be insulated.
The chimney must be at least 4metres high.
As a rule of thumb: 60cm above the ridge of the
roof.
If the ridge of the roof is more than 3metres away
from the flue: stick to the measurements in the
following figure. A = the highest point of the roof
within a distance of 3metres.
Ventilation of the area
For good combustion, the stove needs air(oxygen).
This air is supplied via adjustable air inlets from the
area in which the stove is installed.
The combustion will be incomplete in case of
insufficient ventilation, which results in toxic
gases being produced and spread through the
area.
As a rule of thumb, the air supply should be 5,
5cm²/kW. Extra ventilation is needed when:
The stove is in an area that is well-insulated.
There is mechanical ventilation, for example a
central extraction system oran extraction hood in
an open kitchen.
You can provide extra ventilation by having a
ventilation louvre fitted on the outside wall.
Make sure that otherair consuming appliances (such
as tumble-driers, other heating appliances or a
bathroom fan) have their own supply of outside air, or
areswitchedoff when you use the appliance.
You can also connect the appliance to an
outside airsupply. A connection kit is supplied
for this purpose. This makes additional
ventilation unnecessary.
Floors and walls
The flooron which the appliance is placed must have
sufficient bearing capacity. Forthe weight of the
appliance, see the appendix "Technical data".
Protect flammable flooring from heat radiation
by means of a fireproof protective plate. See
the appendix "Distance from combustible
material".
Remove combustible material such as
linoleum, carpets/rugs and similar materials
below the fireproof protective plate.
Keep sufficient distance between the
appliance and combustible materials such as
wooden walls and furniture.
The connecting tube also radiates heat. Ensure
that there is sufficient distance or a shield
between the connecting tubeand combustible
Subjectto change becauseof technicalimprovements
5
Page 6
material.
The rule of thumbfor a single-walled tubeis a
distance of 3x the diameter. If a lining shell is
fitted around the tube, a distance of 1x the
diameter is permissible.
Carpets and rugs must be at least 80cm away
from the fire.
Use a fireproof floorplate to protect a
flammable floor from any ash which may fall in
front of the stove. The protective plate must
comply with national standards.
For the dimensions of the fireproof protective
plate: see the appendix "Distance from
combustible material".
For further requirements in connection with fire
safety: see the appendix "Distance from
combustible material".
Product description
1. Top plate
2. Latch button
3. Bottom of the fire compartment
4. Door
5. Secondary air slide
6. Leg
7. Primary air slide
Features of the appliance
The appliance is an entirely cast-irondesign with
modern combustion technology.
The airwash-system ensures prolonged clean
glass and so for an optimal view at the fire.
The appliance is supplied with the latch button
installed. As the latch button becomes warm during
use, a glove has beensupplied which you may use
to protect your hand.
The appliance is suitable for connection to outside
air supply. The appliance comes standard with a
connection kit necessary for this.
The appliance can be connected to the chimney at
the rear or at the top.
Installation
General preparation
Please check the appliance immediately after
delivery for damage causedduring transport or any
otherdamage or defects. The appliance is attached
to the pallet with screws at the bottom.
If you detect damage causedduringtransport
or any other damage or defects, do not use the
appliance and notify the supplier.
Remove the removable parts from the appliance
before you start installing the appliance.
It is easier to move the appliance and to avoid
damage if the removable parts have been
removed.
Note the location of the removableparts, so
that you can re-position the parts in the correct
place lateron.
6
Subjectto change becauseof technicalimprovements
Page 7
1. Open the door; see the following figure.
2. Remove the fire-resistant inner plates; see the
following figure.
a. First remove the fire basket (3).
b. Take one of the innerplates (4) out of the
appliance.
c. Thenremove the baffle plate (5)
d. Remove the second inner plate (4)
Vermiculite inner plates are light and tend
to be ochrous in colour on delivery. They
insulate the combustion chamber to boost
combustion.
3. Close the door.
09.20020.100
Removable internal sections
3 fire basket
4 inner plate on the left and right side
5 baffle plate
Connecting to the rear
1. Apply supplied fibre glass sealingtape (2)
measuring 10x3mm to the connection collar's
contact surface (8).
2. Remove the protection plate from the back shield
with the assistance of a screwdriver; see following
figure.
Subjectto change becauseof technicalimprovements
7
Page 8
3. Remove the cover (1) from the back wall.
4. Install the connection collarto the back wall with
the materials.
5. Install the cover in the top plate using the
mounting bracket (4).
Connect to top
On delivery, the connection at the rear is closed, so
that a back cover does not need to be installed.
Because of the distance to the (combustible)
wall, the protection plate may not be removed in the
back shield.
1. Apply supplied fibre glass sealingtape (3)
measuring 10x3mm to the contact surface of the
connection collar (2).
2. Affix the connection collar to the top plate with the
materials supplied.
Preparing the outside air
connection
If the appliance is installed in a room without sufficient
ventilation, you can install the connecting kit onthe
appliance for the supply of outside air.
The airsupply tube is 100mm in diameter. If using a
smooth tube, it may be no longer than 12metres long.
If accessories such as bends are used, the maximum
length (12metres)) must be reduced by 1metrefor
each accessory used.
Outside air connection via the wall
1. Make an opening in the wall (see the appendix,
"Measurements", for the correct position of the
opening).
2. Close the air connection hermetically to the wall.
Installing and connecting
1. Position the stove in the correct place, and make
sure it is level.
2. Connect the appliance airtight to the flue
(chimney).
8
Subjectto change becauseof technicalimprovements
Page 9
3. In the case of connection to outside air: connect
the outside air supply to the connector fitted to the
appliance.
4. Re-position all removed parts in the correct places
in the stove.
Never light a fire in the appliance without the
fireproof inner plates.
The appliance is now ready for use.
Use
First use
When you use the stove for the first time, make an
intense fire and keep it going for a good few hours.
This will cure the heat-resistant paint finish. This may
result in some smoke and odours. You could open
windows and doors for a while in the area in which the
stove is located.
Fuel
This stove is only suitable for burning natural wood;
sawn and chopped wood that is sufficiently dry.
Do not use other fuels, as they can cause serious
damage to the stove.
You are not allowed to use the following fuels, as they
pollute the environment and because they heavily soil
the appliance andflue, which may lead to a chimney
fire:
Treated wood, such as scrap wood, painted wood,
impregnated wood, preserved wood, plywoodand
chipboard.
Plastics, scrap paper and domestic waste.
Wood
Hardwood, such as oak, beech, birch and fruit tree
wood is the ideal fuel for your stove. This type of
wood burns slowly with calm flames. Softwood
contains more resins, burns faster and sparks
more.
Use seasoned wood that contains no more than
20% moisture. The wood shouldhave been
seasoned for at least 2 years.
Saw the wood to size and split it while it is still
fresh. Fresh wood is easier to split, and split wood
dries more easily. Store the wood undera roof
wherethe wind has free access.
Do not use damp wood. Damp logs do not produce
heat as all the energy is used in the evaporation of
moisture. This will result in a lot of smoke and soot
deposits on the stove door and in the chimney. The
water vapour will condense in the stove and can
leak away through chinks in the stove, causing
black stains on the floor. It may also condense in
the chimney andform creosote. Creosote is a
highly flammable compound and may cause a
chimney fire.
Lighting
You can check whether the flue has sufficient draught
by lighting a ball of paper above the baffle plate. A cold
flue often has insufficient draught and consequently,
some smoke may escapeinto the room instead of up
the chimney. You can avoid this problem by lighting
the fire as described below.
1. Stack two layers of medium sized logs crosswise.
2. Stack two layers of kindling crosswise on top of
the logs.
3. Place a firelighter cube in the lower layerof
kindlingand light the cube according to the
instructions on the packaging.
4. Close the door of the appliance and open the
primary air inlet and the secondary air inlet of the
Subjectto change becauseof technicalimprovements
9
Page 10
appliance; see the following figure.
5. Allow the fire develop into a good blaze until there
is glowing bed of charcoal. Youcan thenadd fuel
andadjust the appliance, see the chapter "Stoking
with wood".
Open Closed
Burning wood
After you have followed the instructions for lighting :
1. Slowly open the stove door.
2. Spread the charcoal evenly across the bottom of
the stove base.
3. Stack a few logs onthe charcoal.
Open stacking
If the logs are stacked openly, the wood will burn
quickly as the oxygen can reach each log easily. If
you want to use the stove for a short while, make an
open stack.
Compact stacking
If the logs are stacked tightly, the wood will burn more
slowly as the oxygen can only reach some logs
easily. If you want to burn wood for a longer period,
make a compact stack.
4. Close the door of the appliance.
5. Close the primary air inlet and leave the secondary
air inlet open.
Fill the appliance up to one third capacity.
10
Subjectto change becauseof technicalimprovements
Page 11
Controlling combustion air
The appliance has various features for air control; see
following figure.
The primary air slide controls the air flow underthe
grille (1).
The secondary air slide controls the air flow for the
glass (airwash-system) and air supply via the vents in
the back wall (2).
The back wall has permanent vents (3) below the
baffle plate that allow for post-combustion.
Advice
Never burn wood with an open door.
Regularly burn wood with intense roaring fires.
If you frequently have low intensity fires, tar
andcreosote may be deposited in the chimney
. Tar and creosote are highly combustible
substances. Thicker layers of these
substances may catch fire if the temperature in
the chimney increases suddenly. By allowing
the fire to burn very intensely regularly, layers
of tar and creosote will disappear.
Low intensity fires also cause tar deposits on
the stove window and door.
When the outside temperature is not very low,
it is better to burn wood intensely for a few
hours instead of having a low intensity fire for a
longperiodof time.
Control the air supply with the secondary air inlet.
The secondary air inlet not only supplies air to
the fire but to the glass as well, so that it does
not quickly become dirty.
Open the primary air inlet for the time being if the air
supply by the secondary air inlet is inadequate or if
you want to fan the fire.
It is better to add a small amount of logs regularly
than to add many logs at the same time.
Extinguishing the fire
Do not add fuel andjust let the fire go out. If a fire is
damped down by reducingthe air supply, harmful
substances will be released. For this reason, the fire
shouldbe allowed to go out naturally. Keepan eye on
the fire until it has gone out. All air inlets can be closed
once the fire has died completely.
Removing ashes
After the wood has beenburnt, a relatively small
amount of ashes is left over. This bed of ashes is a
good insulating layer for the stove base plate and
improves combustion. It is goodto leave a thin layer
of ashes on the stove base plate.
The flow of airthrough the fire plate must not be
obstructed, however, and no ash may beallowed to
accumulate behinda cast-ironinner plate. Remove
the excess ash regularly.
Fog and mist
Fog and mist hinder the flow of flue gases through the
flue. Smoke can blow back and cause a stench. If it is
not strictly necessary, it is better not to use the stove
in foggy and misty weather.
Solving problems
Refer to the appendix "Diagnostic diagram" to resolve
any problems in using the stove.
Subjectto change becauseof technicalimprovements
11
Page 12
Maintenance
Follow the maintenance instructions in this chapter to
keep the stove in good condition.
Chimney
In many countries, you are required by law to have
your chimney checked and maintained.
At the beginning of the heatingseason: have the
chimney swept by an expert.
Duringthe heating season and after the chimney
has not been used for a long time: have the
chimney checked for soot deposits.
After the heatingseason: seal off the chimney with
a ball of paper.
Cleaning and other regular
maintenance activities
Do not cleanthe stove when it is still warm.
Clean the exterior of the stove with a dry lint-free
cloth.
You can clean the stove interiorthoroughly at the end
of the heatingseason:
If necessary, first remove the fire-resistant inner
plates. See the chapter "Installation" for
instructions on removing andinstallingthe inner
plates.
If necessary, cleanthe air supply ducts.
Remove the baffle plate at the top of the appliance
andcleanit.
Checking fire-resistant inner plates
The fire-resistant inner plates are consumables and
subject to wear . Check the fire-resistant inner plates
frequently and replace them when necessary.
See the chapter "Installation" for instructions on
removing andinstalling the inner plates.
The insulating vermiculite or chamotte inner
plates may develophairlinecracks, but this
does not affect their performance adversely.
Cast-iron inner plates last a long time if you
remove frequently the ash that can accumulate
behind them. If accumulated ash behind the
cast-iron plate is not removed, the plate will no
longer be able to dissipate the heat to the
surroundings andthis may cause the plate to
warp or crack.
Never use the stove without the fire-resistant
inner plates.
Cleaning glass
Dirt clings less easily to well-cleaned glass. Proceed
as follows:
1. Remove dust and loose soot with a dry cloth.
2. Clean the glass with stove glass cleaner:
a. Apply stove glass cleaner to a kitchen sponge,
rubdown the entire glass surface and give the
cleaning agent time to react.
b. Remove the dirt with a moist cloth or kitchen
tissue.
3. Clean the glass again with a normal glass cleaning
product.
4. Rub the glass cleanwith a dry cloth or kitchen
tissue.
Do not use abrasive or aggressive products to
clean the glass.
Wear household gloves to protect yourhands.
If the glass in the appliance is broken or
cracked, it must be replaced before you can
use the appliance again.
Make sure that no stove window cleaner runs
between the glass and the cast-iron door.
Maintenance enamelled stove
Never clean the stove while it is still hot. The most
effective way to clean the enamelledsurface of the
stove is with a mild green soapand lukewarm water.
Use as little water as possible, rub the surface dry and
prevent the formation of rust. Wire wool or other
abrasives should never beused. Never place a kettle
directly onto an enamelled stove; use a stand to
prevent damage.
12
Subjectto change becauseof technicalimprovements
Page 13
Lubrication
Although cast-iron is slightly self-lubricating, you will
still need to lubricate movingparts frequently.
Lubricate the moving parts (such as guide
systems,hingepins, latches andair slides) with
heat resistant grease that is available in the
specialist trade.
Touching up damaged paint
Small areas of damaged paint finish can be touched
up with a spray can of special heat-resistant paint
finish available from yoursupplier.
Touching up the enamelled surface
Enamelling is a process carried out by traditional
methods, meaningthat it is possible that small colour
differences and damage may occur. The appliances
undergo a visual inspection in the factory, that is to
say, the inspector looks at the surface for a period of
10 seconds from a distance of 1 metre.
Any damage that does not standout is regarded as
OK. A special heat-resistant paint is supplied with the
stove to touch up any minordamage caused during
transport.
Apply the heat-resistant paint in thin layers and leave
to dry well before using the appliance.
Some enamel colours are temperature-sensitive. It
can occur that the colour changes during use. The
original colour will return when the stove has cooled
down.
Checking the seal
Check whether the doorsealing rope is still in good
conditionand works well. The sealing rope is
subject to wear and will need to be replaced over
time.
Check the appliance for air leaks. Close any
chinks with stove sealant.
Allow the sealant to harden fully before lighting
the stove, as any moisture in the sealant will
form bubbles, resulting in a new air leak.
Spare parts 325CB
09.20020.100
Pos. Part number Description Quantity
3 03.77415.000 fire basket
1
4 03.77513.000 side inner plate
2
5 03.77515.000 baffle plate
1
Subjectto change becauseof technicalimprovements
13
Page 14
Appendix 1: Technical Data
Model
325CB
(6 kW)
325CB
(4.9 kW)
Nominal output 6 kW 4.9 kW
Chimney connection (diameter) 125mm 125mm
Weight +/- 100 kg +/- 100 kg
Recommended fuel Wood Wood
Fuel property, max. length 30 cm 30 cm
Mass flow of flue gases 4.1 g/s 3.4 g/s
Flue gas temperature measuredin the
measurement section
274°C 228 °C
Temperature measuredat the appliance
outlet
346°C 285 °C
Minimum draught 12 Pa 12 Pa
CO emission (13%O2) 0.09 % 0.10 %
NOx emission (13%O2) 96 mg/Nm³ 93 mg/Nm³
CnHm emission (13%O2) 123mg/Nm³ 119mg/Nm³
Particulate emission 13 mg/Nm³ 12mg/Nm³
Particulate emission in accordance with
NS3058-NS3059
4,82 gr/kg 4,82 gr/kg
Efficiency 81.0 % 83.3 %
14
Subjectto change becauseof technicalimprovements
Page 15
Appendix 2: Dimensions
325CB
Subjectto change becauseof technicalimprovements
15
Page 16
325CB (GB)
16
Subjectto change becauseof technicalimprovements
Page 17
Appendix 3: Distance from combustible material
325CB - Minimum distance in millimetres
1
2
09-20008-017
1 Combustible material
2 Incombustible material, thickness 100 mm
Please note! To guarantee the flow of combustion air, when no outside air connection is provided, the
distance from the outside airconnection collar to the wall must be at least 20 mm. The connection collar
may be removed where appropriate.
Subjectto change becauseof technicalimprovements
17
Page 18
325CB - Dimensions of fireproof protective plate
A
B B
09-20002-004
Minimal dimensions of fireproof protective plate
A (mm) B (mm)
Din 18891 500 300
Germany 500 300
Finland 400 100
Norway 300 100
18
Subjectto change becauseof technicalimprovements
Page 19
Appendix 4: Diagnostic diagram
Problem
Wood will not stay lit
Gives off insufficient heat
Smoke emissions into the room when adding wood
Fire in stove is too intense, is hard to adjust
Deposit on the glass
Possible cause Possible solution
Insufficient draught
A cold flue usuallyfailsto create sufficient draught. Follow the
instructionsfor lightingin the "Use" chapter; open a window.
Wood too damp Use wood with no more than 20%moisture.
Logs too large
Use smallpieces of kindling.Use splitlogs no larger than 30 cm in
circumference.
Wood stacked incorrectly
Stackthe logs in a way that allows adequate air flow between the
logs(open stacking, see "Burning wood")
Chimney does not work properly
Check whether the chimneymeets the requirements: at least4
metres high, right diameter, wellinsulated, smooth inside, not too
many bends, no obstructions inchimney (bird's nest, too much soot
deposit), hermeticallytight (no chinks).
Chimney stack incorrect Sufficientlyhigh above the roof, no obstaclesin the vicinity
Air inlets setincorrectly Open the air inletscompletely.
Stove connected to the chimney
incorrectly
Connection shouldbe hermeticallytight.
Vacuum in area in whichthe stove is
installed
Switch off extraction systems.
Insufficient supplyof fresh air
Provide an adequate air supply; if necessary use outside air
connection.
Adverse weather conditions?
Inversion (reversed air flow in chimney
because of a high outsidetemperature),
extreme wind speeds
We recommend you don't use the appliance in the case of inversion.
If required, installan extra hood on the flue to increase the draught.
Draught inthe living room
Avoiddraught inthe living room, do not place the appliance near a
door or heating air ducts.
Flames touch the glass
Make sure the wood isnot positioned too close to the glass. Slide the
primary air inletcover closer to the "Closed" position.
Stove is leaking air Check the door seals and stove joints.
Subjectto change becauseof technicalimprovements
19
Page 20
Index
A
Adding fuel 11
Adding wood
smoke emissions into the room 19
Air control 11
Air inlets 9
Air leak 13
Air supply for fire 11
Ashes
remove 11
B
Bearing capacity of floor 5
Burning wood 10
addfuel 11
adding logs 10
appliance is hard to adjust 19
fire is too intense 19
insufficient heat 11, 19
C
Carpet 5
Cast iron innerplates 7
Chimney
connection diameter 14
connection to 8
height 5
sweep 12
Chinks in appliance 13
Clean
glass 12
Cleaning
appliance 12
Combustible material
distance from 17
Connection
dimensions 15
Connection collar for connection to chimney 8
Connection to chimney
at top 8
top 8
Connection to supply of outside air 8
Control air supply 11
Control of air 11
Cover on flue 5
Creosote 11
D
Damage 6
Damp wood 9
Dimensions 15
Door
open 7
sealingrope 13
Draught 14
Drying wood 9
E
Efficiency 14
Enamel
maintenance 12
F
Filling height 10
Finishingcoat, maintenance 13
Fire
extinguishing 11
lighting 9
Fire-resistant innerplates
maintenance 12
remove 7
Fire going out 11
Fire safety
distance from combustible material 17
floor 5
furniture 5
walls 5
Fireproof inner plates
warning 9
Floors
bearingcapacity 5
fire safety 5
Flue
maintenance 12
requirements 4
Flue gas
mass flow 14
temperature 14
Fog, do not burn wood 11
20
Subjectto change becauseof technicalimprovements
Page 21
Subjectto change becauseof technicalimprovements
21
Fuel
adding 11
adding wood 10
necessary amount 11
suitable 9
unsuitable 9
wood 9
G
Glass
clean 12
deposit 19
H
Heat, insufficient 11
Heat,insufficient 19
Hood on the flue 5
I
Innerplates
vermiculite 7
Innerplates, fire-resistant
remove 7
Installation
dimensions 15
K
Kindled fire 9
Kindling 19
L
Lighting 9
Lubricant 13
Lubricate 13
M
Maintenance
chimney 12
clean glass 12
cleaning the appliance 12
enamel 12
fire-resistant inner plates 12
lubrication 13
sealing 13
Mist, do not burn wood 11
N
Nominal output 11, 14
O
Open
door 7
Outside air intake
connection to 8
P
Paint finish 9
Particulate emission 14
Parts, removable 6
Prevent a chimney fire 11
Primary air inlet 9
R
Removable parts 6
Removal of ashes 11
Remove
fire-resistant inner plates 7
Remove ashes 11
S
Screens
clean 12
deposit 19
Sealing ropefor door 13
Secondary air inlet 9
Smoke
on first use 9
Smoke emissions into the room 4, 19
Softwood 9
Solving problems 11, 19
Stacking logs 10
Storingwood 9
Stove window cleaner 12
Suitable fuel 9
Supply of outside air 5, 8
Sweep chimney 12
T
Tar 11
Temperature 14
U
Unsuitable fuel 9
Page 22
V
Ventilation 5
connect supply of outside air 8
ruleof thumb 5
Ventilationlouvre 5
Vermiculite
fire-resistant 7
Vermiculite inner plates 7
W
Walls
fire safety 5
Warning
chimney fire 4, 9, 11
combustible materials 4
fireproof inner plates 9
glass brokenor cracked 4, 12
hot surface 4
regulations 4
stove window cleaner 12
terms and conditions for insurance 4
ventilation 4-5
Weatherconditions, do not burnwood 11
Weight 14
Wood 9
damp 9
does not keep burning 19
drying 9
right sort 9
storing 9
22
Subjectto change becauseof technicalimprovements
Page 23
Loading...