Doughpro SL1577 Installation Manual

DDUDHPRD

Operation Manual

Operation Manual

SL1577

SL1577

Digitally Controlled Split Lid Toaster

Digitally Controlled Split Lid Toaster

DDUDHPRD

PROPROCESS CORPORA TION

P.O. Box 869O7328 Madison St.OParamount, CA 90723

PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor

[phone]

O

[phone]OFax [phone]

Website: www.doughpro.com OE-Mail: [e-mail]

Website: www.doughpro.com E-Mail: info©doughpro.com

S

tep 1

Operation Instructions

Step 2

Carefully unpack and clean grill plates with
mild soap then sponge clean with cold water.

W

ARNING

Place in location where it will be used allowing
for clearances per the dimensions indicated.

OALLOW 2” MINIMUM CLEARANCE between

adjacent equipment and/or wall areas.

ODO NOT touch hot surfaces.

S

tep 3

Plug into proper 3 prong wall outlet. If other appliances are connected to the same circuit make sure
the total load does not exceed maximum ampacity of the circuit. Electrical information as follows:

120V / 50/60Hz / 1 Phase / 2200W / 18.3 A (20 Amp Circuit).

220V / 50/60Hz / 1 Phase / 2200W / 10.0 A (20 Amp Circuit).

S

tep 4: Warm-up

Energize by turning on the power switch which will illuminate when turned on.

OThe display flashes and shows left preset timer during warm-up.
OPre-heat temperature time will be 40-50 minutes.
OWhen the setpoint is reached, the display stops flashing and beeps 3 times.

tep 4: Operation

S

OSimply place product on either side of the grill, close lid and

press the desired pre-set time cycle 15 or 27 seconds. After
the time cycle is finished press it again to reset the time cycle.

OTo grill a larger product simply align both platens and slide the

locking guide into position so that both platens become one.

Clean Cycle

To start a clean cycle, push CLEAN button once so the CLEAN LED light is turned on. All preset

0

LED’s are turned off, and the temperature setpoint is changed to the clean setpoint of 275

F. This
also initiates the cool down to clean setpoint condition as well the display starts flashing until the
clean setpoint is reached.

To stop the clean cycle,simply press the CLEAN button once to deactivate the clean cycle. The
CLEAN LED is turned off, the preset LED’s are restored, the temperature set point is changed to the
main setpoint. Again, the warm-up condition is initiated and the display flashes until the cook setpoint
is reached.

FOR SERVICE CALL: [phone]

PROPROCESS CORPORA TION

P.O. Box 869O7328 Madison St.OParamount, CA 90723

PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor

[phone]

O

[phone]OFax [phone]

Website: www.doughpro.com OE-Mail: [e-mail]

DDUDHPRD

SL 1577 Operating Instructions:

SL1577 Operating Instructions:

1. Press desired time to start the time cycle. After the cycle is finished,

1. Press desired time to start the time cycle. After the cycle is finished,

press it again to reset the time cycle.

press it again to reset the time cycle.

Digital Time

Digital Time

Display

Display

Clean Cycle 275

Clean Cycle 275

o

Temperature

Temperature

Controls

Controls

0271

1.5.lS.4tW.E:1J.1:

ATTENTION:

ATTENTION:

To maintain proper temperature

To maintain proper temperature

settings close lid when not in use.

settings close lid when not in use.

HOW TO FIND TEMPERATURE:

HOW T

1. To find the temperature of the UPPER PLATENS:

2. To find the temperature of the LOWER PLATENS:

O FIND TEMPERATURE:

To find the temperature of the UPPER PLATENS:

Press the TEMPERATURE button and the ARROW UP button at the same time.

Press the TEMPERATURE button and the ARROW UP button at the same time.

To find the temperature of the LOWER PLATENS:

Press the TEMPERATURE button and the ARROW DOWN button at the same time.

Press the TEMPERATURE button and the ARROW DOWN button at the same time.

Power Button Flat Bread

Power Button

Flat Bread

Quesadilla,

Quesadilla,

Burrito

Burrito

FOR SERVICE CALL: [phone]

FOR SERVICE CALL: [phone]

DDUDHPRD

PROPROCESS CORPORA TION

P.O. Box 869O7328 Madison St.OParamount, CA 90723

PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor

[phone]

O

[phone]OFax [phone]

Website: www.doughpro.com OE-Mail: [e-mail]

Website: www.doughpro.com E-Mail: [e-mail]

DDUDHPRD

Instruction’s for Adjusting the Temperature

Instruction's for Adjusting the Temperature

PRESS and hold the TEMP and ARROW up

PRESS and hold the TEMP and ARROW up

buttons simultaneously for 5 seconds.

buttons simultaneously for 5 seconds.

The current temperature setting will display on the right

The current temperature setting will display on the right

digital display only.

digital display only.

Using the ARROW buttons, you may now adjust the temperature to your

Using the ARROW buttons, you may now adjust the temperature to your

desired setting.

desired setting.

Once you have set your desired temperature simply push

Once you have set your desired temperature simply push

the TEMP button. The digital displays will now read the

the TEMP button. The digital displays will now read the
preset times.

preset times.

Instruction’s for Adjusting the Set-Time

Instruction's for Adjusting the Set-Time

. 2

PRESS the desired button you

PRESS the desired button you

wish to program.

wish to program.
Now press BOTH button and

Now press BOTH button and

TEMP buttons simultaneously

TEMP buttons simultaneously

for 5 seconds.

for 5 seconds.

The digital displays will now read their preset times as

The digital displays will now read their preset times as

shown here. Each side is capable of having up to 4

shown here. Each side is capable of having up to 4

different settings, making a total of 8 set-times.

different settings, making a total of 8 set-times.

Now using the ARROW buttons you

Now using the ARROW buttons you

can set your desired time.

can set your desired time.

Once you have set the desired time simply press the

Once you have set the desired time simply press the

TEMP button, the unit will display the new set-time.

TEMP button, the unit will display the new set-time.

. 1

*IMPORTANT NOTE: When adjusting the time settings, The RIGHT SIDE time buttons

*IMPORTANT NOTE: When adjusting the time settings, The RIGHT SIDE time buttons

control the left side, so the same time you set on the right will automatically be set to

control the left side, so the same time you set on the right will automatically be set to

the left side accordingly. If you desire an additional set of times you can adjust the left

the left side accordingly. If you desire an additional set of times you can adjust the left

side AFTER you have adjusted the right side without effecting the right side settings.

side AFTER you have adjusted the right side without effecting the right side settings.

PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor