Doug Fleenor Designs RERUN-A Users Manual
RERUN ARCHITECTURAL
DMX512 RECORDER
MODEL RERUN-A
OWNERS MANUAL
Doug Fleenor Design
396 Corbett Canyon Road
Arroyo Grande, CA 93420
(805) 481-9599
Software Version 1.5
Manual Revision 1.1
$ Serial #109001
PRODUCT DESCRIPTION
The Rerun Architectural is a lighting control station capable of storing up to ten 40-minute shows. Shows
are recorded by capturing the output of a DMX512 console. The recorded show start and end points may
be trimmed non-destructively. Each show can be set to hold the last look, loop to itself or link to another
show. Shows are started by pressing one of the ten show buttons.
A basic system consists of a Rerun Architectural station and a power supply. The solid aluminum faceplate
is designed to install over a standard two gang electrical box. Single gang remote stations can be added
to remotely select shows. Connections to the Rerun Architectural are power (2 wires), DMX512 Input (3
wires) and DMX512 Output (3 wires). Power for the Rerun Architectural can be supplied from a variety
of sources, including a 10V class 2 “doorbell” transformer.
The Rerun Architectural system can work in conjunction with a lighting console, automatically switching
between recorded shows and console control. When the console generates DMX512 the Rerun
Architectural retransmits the incoming DMX512 data. Thus the console operates normally. Upon loss of
DMX512 from the console, the Rerun Architectural starts its previously active show.
Rerun also comes in a portable version (model RERUN-P) and a rack mount version (model RERUN-R?)
The Rerun Architectural and Rerun Portable units can support one universe of DMX512 data. The rack
mount version can be built to support multiple universes of DMX512. Substitute the number of universes
in place of the question mark in the model number for the rack mount version. As many as four universes
can be supported in a single 1U chassis. Additional universes can be supported in the rack mount version
using expansion units.
Page 2 of 14
SPECIFICATIONS
Connector: Terminal block #1
Phoenix Contact MSTB series
5 position two part terminal block
Model: MSTB 2,5/5-ST-5,08
Order number: 17 57 04 8
Connector pin out: Terminal Block #1 (DMX512 Output) Terminal Block #2 (DMX512 Input)
1 (C) DMX512 common 1 (C) DMX512 common
2 ( -) DMX512 data - 2 ( -) DMX512 data 3 (+) DMX512 data + 3 (+) DMX512 data +
4 (C) Supply common
(internally tied to pin1)
5 (V) Supply voltage “hot”
Input Circuit: ESD protected EIA-485 transceiver (LT1785)
Output Circuit: ESD protected EIA-485 transceiver (LT1785)
Isolation: None. DMX input is not isolated from DMX output.
Indicators: Ten green SHOW LEDs
One green PAUSE LED
One green LOOP LED
One yellow START LED
One yellow END LED
One red INPUT/RECORD LED
User controls: Ten [SHOW] buttons
One [PAUSE] button
One [LOOP] button
One [REWIND] button
One [FORWARD] button
One recessed [RECORD] button
Terminal block #2
Phoenix Contact MSTB series
3 position two part terminal block
Model: MSTB 2,3-G-5,08
Order number: 17 55 74 9
Option Jumpers:
JP1
JP2
JP3
JP4
JP5
JP6
INSTALLED REMOVED
Recording enabled Recording/editing disabled
Run show on DMX512 loss Hold last look on DMX512 loss
Normal operation Run hardware test
Normal operation Factory use only
Pile-on mode disabled Pile-on mode enabled
Normal operation Erase memory (DANGER!)
Page 3 of 14
SPECIFICATIONS (CONTINUED)
Power input: 9 to 15 volts AC or DC / 150mA per station
(A 10 volt class 2 “doorbell” transformer is recommended for fixed installations)
Color: Black anodized with laser engraved nomenclature
Size : Faceplate: 4.5"h X 4.6"w X 0.2"d
Faceplate rear inset: 4.15"h X 4.25"w X 0.1"d
Electrical box minimum inside dimensions: 2.9"h X 3.5"w X 1.5"d
POWER SUPPLY
The voltage provided to the Rerun Architectural must be between 9 and 15 volts AC or DC. The Rerun
Architectural has been designed to operate on a standard class 2 “doorbell” transformer. For example Ace
Hardware’s model# ACE36483 10 volt 5 watt transformer.
Doorbell
Transformer
Page 4 of 14
WIRING INFORMATION
Rerun Architectural is designed to use daisy-chain wiring topology. Please give us a call if you have
any questions.
Note:
! DMX512 from a console will not pass through if the Rerun Architectural is not powered .
CABLE COLOR FROM TO USE
120 Ohm D ata Cab le
1
Belden 9829 or Equivalent
(2) #16 AWG
2
Stranded Wires
120 Ohm D ata Cab le
5
Belden 9829 or Equivalent
Sh ield
W hite/Blue Pin 2 DMX IN (-) Data -
Blue/White Pin 3 DMX IN (+) Data +
Black
Red Power
Sh ield
W hite/Blue PW R/DMX OUT (-) ? Data -
Blue/White PW R/DMX OUT (+) ? Data +
XLR Plate
Power S upply
RE R U N -A
Pin 1
RE RU N-A
Com m on PW R/DMX O UT (C) Sup ply
PWR/DMX OUT (C)
Dim mer
Cabinet
DMX IN (C) Comm on
PW R/DMX O UT (V)
? Comm on
Sup ply “hot”
OPTIONAL REMOTE PANEL
CABLE COLOR FROM TO USE
120 Ohm D ata Cab le
1
Belden 9829 or Equivalent
(2) #16 AWG
2
Stranded Wires
120 Ohm D ata Cab le
3
Belden 9829 or Equivalent
(2) #16 AWG
4
Stranded Wires
120 Ohm D ata Cab le
5
Belden 9829 or Equivalent
Sh ield
W hite/Blue Pin 2 TB1-2 Data -
Blue/White Pin 3 TB1-3 Data +
Black
Red Pow er TB1-5 S upply “hot”
Sh ield
W hite/Blue TB1-2 DMX IN (-) Data -
Blue/White TB1-3 DMX IN (+) Data +
Black TB1-4
Red TB 1-5
Sh ield
W hite /Blue
Blue/White PW R/DMX OUT (+) ? Data +
XLR Plate
Power S upply
PR E10 -A
Slave
RE R U N -A
Pin 1
PR E10 -A
Slave
Comm on TB1-4 Supply
TB1-1
RE RU N-A
PW R/DMX O UT (C)
PW R/DMX O UT (-)
Dimmer
Cabinet
TB1-1 Comm on
DMX IN (C) Comm on
PW R/DMX O UT (C)
PW R/DMX O UT (V)
? Comm on
? Data -
Supply
Sup ply “Hot”
Page 5 of 14
Loading...