Doug Fleenor Designs DMX8DIM Specifications

DOUG FLEENOR DESIGN

Low Power, 8 Channel, DMX512 Dimmer

model: dmx8dim

technical data sheet

The dmx8dim is an eight output ‘green' dimmer designed for
high efficacy loads, low idle power, and minimal losses. Typical
loads include LED lamps, Neon, Compact Fluorescent,
Electronic and Magnetic Low Voltage, and low power halogen.

The dimmer electronics are housed in a 12x12x4 inch NEMA
Type 1 enclosure and are easily removable so the enclosure can
be installed and rough wired without the electronics in place.
Then, upon completion of dry wall, the electronics can be
reinstalled using only four screws. A protective bag is included
for storing the electronics during installation. Wiring is by
compression type screw terminal blocks. Rated at 240 Watts
per output, the dimmer has self resetting overload protection and
is powered by a single 20A branch circuit. Features include
dim/non-dim per output, local control for load testing, a
troubleshooting LED, and an optically isolated DMX input.
DMX512-A compliant, ETL listed to UL508.

If you would like assistance in your application, please give us a
call. We like to talk with our customers.

SPECIFICATIONS: All specifications meet or exceed DMX512 requirements

Input circuit: Protected EIA-485 receiver (LT1785). Transient protected to 15 KV, Continuous to 60 V.

Input signal: 0.2 volts minimum, 12 volts maximum, DMX512, DMX512/1990, or DMX512-A.

Signal Connectors: Phoenix Contact Combi-Con Pluggable terminal blocks. Two provided: In and Through.

Termination: Removable 120 Ohm termination provided on feed through.

Power Input: 120 VAC 60 Hz 16 Amps at full load (Uses 20 Amp branch circuit at 80% capacity).

Actual current draw is connected load plus 50 mA (m ax).

Idle Power: Less than 1 W att.

Input Power Connector: Three position screw terminal block accepts up to 12 AWG solid or stranded wire (Line,

Neutral, Ground).

Power Output: 120 VAC 60 Hz 2 Am ps per output.

Output Protection: 2 Amp self resetting over current device on output, 100 Ohm PTC thermistor on driver.

Output Connectors: One three position screw terminal block per output accepts up to 12 AWG solid or

stranded wire (Line, Neutral, Ground).

Dimming Circuit: Digitally fired, phase controlled 16 Amp snubberless triac (Alternistor) with high dv/dt

driver. Triacs are screwdriver replaceable. One spare triac provided. A leakage control
circuit on each output prevents ghosting of moderate loads.

SPECIFICATIONS: (Continued)

Rise Time: 12 uS (10% to 90% at 90 degree firing angle) at rated load.

Dimming Curve: Square law. Visually appealing on LED lamps (120V), halogen lamps, magnetic low-

Non-dim Curve: Outputs set to non-dim turn on at 60%, off at 40%. Outputs switch at zero crossing.

DMX Footprint: Eight consecutive DMX slots beginning with the selected DMX Starting Address.

DMX Starting Address: Nine position internal DIP switch. Must be set at time of install. Not user accessible.

Non Dim Switch: Nine position internal DIP switch. One switch per output plus ‘local’. Not user accessible.

Local Control Switch: When local switch is ON, Non-dim switches function as on/off switches for load testing.

Chase Mode: Factory programmable chase sequence (default is 8-step chase 1/8 seconds per step).

Status Indicators: One multi function LED : Blinking Red: power with no signal.

Cooling: Maintenance free convection with front panel ventilation. No fan.

voltage (MLV) and electronic low-voltage (ELV).

Solid Red: local control switch on.
Blinking Green: DMX control signal present.
Solid Green: Output 1 on.

Isolation: Double isolated: DMX512 input is isolated from control electronics to 1500 Volts. Control

electronics are isolated from AC power circuits to 600 Volts.

Color: Gray rear and sides, Green front.

Knock-outs: Ten provided (five each on top and bottom). Each knock-out accepts two fitting sizes.

There are two each of 0.75" / 1.00" and 0.50" / 0.75" and one of 1.00" / 1.25"

Safety listing: ETL listed to UL 508

Size and Weight: 12.1" x 12.1" x 4.4" 10 Pounds

Warranty: Five years parts and labor. Dimmer electronics must be returned to Doug Fleenor Design

for warranty repair (enclosure can remain in place). Shipping to Doug Fleenor Design is
to be paid by the customer. Return ground freight is paid by Doug Fleenor Design. Costs
to remove and re-install the dimmer electronics are not covered. W arranty covers
manufacturing defects. Damage caused by improper installation or mis-use are not
covered.