DOUBLE WIN ENTERPRISE DW920290 User Manual

DW LINK 2003/05/01
Wireless Access Point
User’s manual
Model: PL9510 -WAP

FCC STATEMENT
This product has been tested and complied with the specification for a class B digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This device complies with part 15 of the FCC Rules operation is subject to the
following two conditions (1) This device may not cause harmful interference, and (2)
This device must accept any interference received, including interference that may
cause undesired operation.
If this device does cause harmful interference to radio or television, which is found by

tuning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures;

•Reorient or relocate the receiving antenna.

•Increase the separation between and equipment or device.

•Connect the equipment to and outlet oth er than the receivers

•Consult a dealer or an experienced radio/TV technician for assistance.

FCC Radiation Exposure Statement
This equipment complies with FCC radiation limits set forth for an uncontrolled
environment. This equipment should be installed and operate with minimum distance 20
cm between radiator and your body.

Instruction
Step into the digital age and network your home or office the easy way Combining
two revolutionary networking technologies developed as part of computing world’s
most recent renaissance, Powerline and WiFi, the WireLink PL Wireless Access Point
PL9510-WAP allows you to extend your Powerline network into a Wireless as well.
Instantaneously, you can broaden your Powerline network beyond just the inside of
your home or office and increase your wireless network from a mere 100feet to over
3,300 feet!
The WireLink PL Wireless Access Point offers a convenient way to create a simple
network through the existing electrical wiring of a home or office with the additional
ability to provide you with access to your network without wires. Offering two levels
of security, the WireLink PL Wireless Access Point is built with 128-bit WEP
encryption for the wireless pass-through and 56-bit DES encryption for the Powerline
pass-through so your data will always be secured- guaranteed.

Features:

◆ Up to 11 Mbps of Data Transmission

◆ Interoperable with IEEE 802.11b (DSSS)

◆ Capable of up to 128-bit WEP Encryption

◆ Easy Set-up and Installation

◆ Equipped with HomePlug® 1.0

◆ Built-in Quality of Service (QoS) and Data Error Detection and Correction

Technologies

◆ Power, WLAN Tx, WLAN Rx, PL Act

◆ Operate Range Supports 150m(Indoor)

Cabling Type

◆ Standard AC Plug

◆ Phone line

Environmental：
Dimensions (LxWxH)

◆ 3.9”Lx5”Wx1”H

◆ Weight 0.69 lbs

Power Input ：110V AC

◆ Safety & EMI :TBA

Operating Temperature

◆ 32°F to 131°F (0°C to 55°C)

Storage Temperature

◆ -4°F to 131°F (-20°C to 70°C)

Operating Humidity

◆ 10% to 85% Non-condensing

Storage Humidity

◆ 5% to 90% Non-condensing

Package Contents:

•One WireLink PL Wireless Access Point user manual

•One AC adapter( AD75)

•Two Detachable Antennae

•one setup CD—ROM

•One Wireless card ( optional)

• One hook up kits package
. One PA50 phone adaptor
System Requirements

•A Note book with Wireless Card(IEEE 802.11b).

•A PC with support Ethernet connection

•Window 98, 2000, ME, XP

•One WireLink PL product

•A 10 Mbps Category 3 or Better network RJ-45 connection.

The WireLink PL Wireless Access Point Rear Panel

The WireLink PL Wireless Access Point’s Ports

Dipole Antenna Connectors:
The Two round connectors( SMA F) are where the antenna are connected to the
Access Point

This antenna connector ( SMA-F) is “ unique” which is SMA- Female socket inside,
male pin, it is different from normal one which is SMA-Female socket..
It has to install the original one shipping with package.

AD75 Power connector
The DC power connector are 3 pins, where the Power line signal are connected to unit.
This is adapter includes coupler which is designed by WireLink company, it can’t
replace with any AC/DC adapter.

WireLink PL Wireless Access Point Front Panel

Power LED